Fmwcc38

Transcript

Fujitsu Personal Systems, Inc. has made every effort to ensure the accuracy and completeness of this document; however, because ongoing development efforts are made to continually improve the capabilities of our products, we cannot guarantee the accuracy of the contents of this document. We disclaim liability for errors, omissions, or future changes herein. Fujitsu is a registered trademark of Fujitsu, Ltd. Stylistic LT is a trademark of Fujitsu Personal Systems, Inc. MS, MS-DOS, and Microsoft are registered trademarks of Microsoft Corporation. Windows 98 is a trademark of Microsoft Corporation. Pentium is a registered trademark of Intel Corporation. MMX is a trademark of Intel Corporation. Intellisync is a registered trademark of Puma Technology, Inc. All other products are trademarks or registered trademarks of their respective companies. Copyright 1999 Fujitsu Personal Systems, Inc. No part of this publication may be copied, reproduced, or translated, without the prior written consent of Fujitsu Personal Systems, Inc. No part of this publication may be stored or transmitted in any electronic form without the prior consent of Fujitsu Personal Systems, Inc. Agency Compliance Warnings and Cautions 0 Warnings and Cautions that appear in this manual should be closely heeded. Warnings represent situations that are potentially harmful to the user. Cautions represent situations that can cause physical damage to the system or other equipment. UL Notices 0 Cautions • For continued protection against the risk of fire, replace only with the same type and rating of fuse. • There is a danger of explosion if the CMOS battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to manufacturer's instruction. • Changes or modifications not expressly approved by Fujitsu Personal Systems, Inc. could void this user’s authority to operate the equipment. Warnings • The CMOS battery may explode if mistreated. Do not recharge, disassemble, or dispose of in fire. • For spare battery packs, order only Fujitsu Models FMW29BP1 (6-cell) or FMW29BP2 (3-cell). • To charge battery packs FMW29BP1 or FMW29BP2 externally, use only a Stylistic LTTM external battery charger FMW51BC1. iii FCC Notices 0 DECLARATION OF CONFORMITY according to FCC Part 15 Responsible Party Name: Fujitsu Personal Systems, Inc. 5200 Patrick Henry Drive Santa Clara, CA 408-982-9500 Address: Telephone: Declares that product: Model: Stylistic LT Complies with Part 15 of the FCC Rules This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. David Woo - Mgr. Agency Compliance Full Name / Title Note: iv May 28, 1999 Date The Stylistic LT is available in a number of different configurations, as delineated in the following table. For more detailed information about the FCC rules and their applicability to the Stylistic LT pen tablet, refer to Appendix A of this document. Screen Type Modem? LAN? Cord Type Part Number TFT NO NO US FMW2900TA01 TFT YES NO US FMW2901TA01 TFT NO YES US FMW2902TA01 TFT NO NO UK FMW2900TB01 TFT NO YES UK FMW2902TB01 TFT NO NO EURO FMW2900TC01 TFT NO YES EURO FMW2902TC01 CTF NO NO US FMW2900FA01 CTF YES NO US FMW2901FA01 CTF NO YES US FMW2902FA01 CTF NO NO UK FMW2900FB01 CTF NO YES UK FMW2902FB01 CTF NO NO EURO FMW290OFC01 CTF NO YES EURO FMW2902FC01 Table of Contents Warnings and Cautions ............................................................................. UL Notices.................................................................................................... FCC Notices ................................................................................................. iii iii iv Chapter 1 Getting Started Included with the Stylistic LT Pen Tablet ............................................... Optional Accessories .................................................................................. Stylistic LT Pen Tablet Features................................................................ Status Indicators.......................................................................................... Connectors and Peripheral Interfaces..................................................... 1-1 1-2 1-3 1-6 1-9 Chapter 2 Using the Stylistic LT Pen Tablet System States ............................................................................................... Using the Pen............................................................................................... Using Hovering Mode.................................................................... Starting the Pen Tablet ............................................................................... Using the Security Card ............................................................................. Shutting Down the System ........................................................................ Suspending System Operation.................................................................. Resuming System Operation..................................................................... Using Hotpads............................................................................................. Charging the Battery Pack ......................................................................... Removing and Installing the Battery Pack.............................................. Conserving Battery Power......................................................................... Modem Connection .................................................................................... LAN Connection ......................................................................................... PC Card Slots............................................................................................... 2-1 2-3 2-3 2-4 2-4 2-7 2-7 2-9 2-10 2-12 2-13 2-15 2-16 2-17 2-18 Chapter 3 Care and Maintenance Protecting the Display Screen ................................................................... Storing the Stylistic LT Pen Tablet............................................................ Protecting the Stylistic LT Pen Tablet in Harsh Environments............ Avoiding Overheating ............................................................................... Cleaning the Display Screen...................................................................... Calibrating the Pen ..................................................................................... Replacing the Pen........................................................................................ Solving Problems ........................................................................................ System Will Not Resume Operation ............................................ Display Screen Is Blank or Difficult to Read............................... Infrared Data Transfer Is Not Working ....................................... Pen Tablet Is Not Responding to the Pen.................................... Cursor Is Not Tracking Pen........................................................... 3-1 3-2 3-3 3-3 3-3 3-4 3-5 3-6 3-6 3-6 3-7 3-7 3-7 v Audio Volume Is Too Low ............................................................ Configuring Peripherals Interfaces .............................................. 3-8 3-8 Chapter 4 Using the Optional Peripherals Stylistic LT Mini-Dock................................................................................ Installing the Stylistic LT into the Mini-Dock............................. Removing the Stylistic LT from the Mini-Dock.......................... Stylistic LT Charge-Only Dock ................................................................. Installing the Stylistic LT into the Charge-Only Dock .............. Removing the Stylistic LT from the Charge-Only Dock ........... Stylistic LT Wireless Keyboard ................................................................. Using the Wireless Keyboard........................................................ Entering an Identification Code................................................ Encountering Problems when Using the Wireless Keyboard Replacing the Wireless Keyboard Batteries ............................ 4-1 4-4 4-5 4-5 4-6 4-6 4-7 4-7 4-8 4-8 4-9 Appendix A Agency Notices FCC Notices ................................................................................................. Notice to Users of Radios and Television.................................... Notice to Users of the U.S. Telephone Network......................... DOC (Industry Canada) Compliance Notices ........................................ Notice to Users of Radios and Television.................................... Notice to Users of the Canadian Telephone Network............... Avis Aux Utilisateurs Du Réseau Téléphonique Canadien...... vi A-1 A-1 A-1 A-3 A-3 A-3 A-4 Chapter 1 Getting Started The Stylistic LT™ pen tablet is a high-performance, pen-based computer that is designed to operate under Windows 98. This chapter provides an overview of the Stylistic LT pen tablet and its features. Included with the Stylistic LT Pen Tablet 1 The following items are included with the Stylistic LT pen tablet: • Stylistic LT pen • Stylistic LT 3-cell battery pack • AC adapter • Screen protectors (quantity: 2) • Hard disk drive with Windows 98 operating system installed in the pen tablet • Microsoft Windows 98 operating system user’s guide with certificate of authenticity for operating system software • Certain Stylistic LT models are equipped with either an optional internal 56 Kbps modem*† or an optional internal LAN card. * The 56 Kbps rate is nominal; due to FCC restrictions, actual rates are limited to 53 Kbps. † The internal modem is available as an option in North America only. 1-1 Optional Accessories 1 The following optional accessories can be used with the Stylistic LT pen tablet. Refer to the instructions provided with these accessories for details on their use.* • Auto Adapter FMWCB2 • Mini-Dock FMW29PR1* • Charge-Only Dock FMW29CR1* • External Floppy Disk Drive FMWFD2 • Wireless Keyboard*: • North America - FMWKB4A • United Kingdom -FMWKB4B • Germany - FMWKB4D • France - FMWKB4F • Holster A FMWCC34 • Holster B FMWCC37 • Folding Desk Stand FMWDS3 • Compact Desk Stand FMWDS4 • Carrying Case FMWCC38 • Harsh Environment Case FMWCC39 • Portfolio Case FMWCC40 • Slipcase FMWCC41 • Battery Pack (3 cell) FMW29BP2 • Battery Pack (6 cell) FMW29BP1 • External Battery Charger FMW51BC1 • Screen Protectors (package of 12) FMWSP8 • Pen (package of 5) FMW29PN1 • Security Card (package of 10) FMW29SC1 * Instructions for use of the Stylistic LT mini-dock, the charge-only dock, and the wireless keyboard are also included in Chapter 4 of this manual; instructions for the other options are shipped with the individual peripherals. 1-2 Getting Started Stylistic LT Pen Tablet Features 1 Features and controls that you use to operate the Stylistic LT pen tablet are described briefly below and illustrated in Figures 1-1 and 1-2. Details on using these features and controls are provided later in this manual. Front and Side Features (Figure 1-1): 1 • Display: Provides an area where you read information and enter data with the pen. • Status Indicators: Indicate the pen tablet’s power status, battery charge level, hard disk access, and hovering state. Reference Chapter 2 for additional information on the hovering state. • Pen: Acts as the main pointing device that you use to run programs and enter data. A pen holder is built into the pen tablet to store the pen when not in use. • Speaker: Allows you to play back audio files monaurally without external hardware. • Microphone Jack: Allows you to connect an external microphone*. • Headphone Jack: Allows you to connect stereo headphones*. • Infrared I/O Port: Provides an infrared interface for communication with devices compliant with IrDA Standard Revision 1.1. • Wireless Keyboard Infrared Port: Provides an infrared interface for communication with the optional wireless keyboard*. Refer to Chapter 4 of this manual for instructions on using the keyboard. • Hotpad Area: Contains several keys that allow you to change settings for the display and speaker, and to allow emulation of a right mouse button. The hotpads also let you select hovering mode and to Save-to-Disk by tapping with the pen. • Mini-Dock Connector: Allows you to install the Stylistic LT in an optional mini-dock* for enhanced connectivity. Refer to Chapter 4 of this manual for instructions on using the mini-dock. • Charging Contacts: Provide power to the system when installed in either the mini-dock* or charge-only dock*.. Refer to Chapter 4 of this manual for instructions on using the charge-only dock. * These peripherals and accessories are sold separately. Stylistic LT Pen Tablet Features 1-3 Hotpad Area Pen Holder Display Status Indicators Charge-only Contacts Mini-dock Connector Speaker Headphone Jack Microphone Jack Figure 1-1 Infrared I/O Port Wireless Keyboard Infrared Port Stylistic LT Pen Tablet Features (Front View) Rear and Side Features (Figure 1-2): 1 • DC Input Connector: Allows you to connect the AC adapter or auto adapter.* • Removable Battery Pack: Provides power to the system when not connected to AC power. • Battery Latch: Secures the removable battery pack when it is installed in the system. • Suspend/Resume Button: Allows you to suspend or resume system operation in order to optimize battery life. • Reset Button: Restarts the pen tablet in the event of system difficulty. Note that pressing this button results in loss of active data. * These peripherals and accessories are sold separately. 1-4 Getting Started • PC Card Door: Allows you to access PC Cards* installed in the PC Card slots. Note that Slot 2 is closest to the display. • Eject Buttons: Allow you to eject a PC Card from a PC Card slot. • USB Port: Allows you to connect Universal Serial Bus-compliant devices to the pen tablet. • Modem Port†: Allows you to connect a standard RJ-11 telephone plug to the pen tablet’s optional internal modem. * These peripherals and accessories are sold separately. PC Card Slots Removable Battery Pack Eject Buttons Battery Latch Suspend/Resume Button Figure 1-2 DC Input Reset Button USB Port Modem Port † Stylistic LT Pen Tablet Features (Rear View) † The modem port is found only on those systems containing an internal modem. The internal modem is available as an option in North America only. Stylistic LT Pen Tablet Features 1-5 Status Indicators 1 Icons appear in the Status display indicating the status of system functions such as system power and battery charge level. The location of icons in the Status indicator section is shown in Figure 1-3. (Power) (Charging) (HDD Access) (Hovering/ Security) Figure 1-3 1-6 Getting Started Status Indicator Icons Table 1-1 shows how the LEDs associated with the individual icons are displayed, and describes what the variations of that display indicate. (If an icon LED is not lit, it indicates that the related system function is off or inactive. Table 1-1 Icon LED Status On Color System Status Indications System Function Green Power On (with battery between 13% and 100%) Amber Power On (during short periods when the system is checking remaining battery life) Red Power On (with battery at 12% or less charge, or no battery installed) Green Suspend Mode (with battery between 13% and 100%) Amber Suspend Mode (during short periods when the system is checking remaining battery life) Red Suspend Mode (with battery at 12% or less charge, or no battery installed) Off Unlit Power Off or Save-to-Disk On Green Charging is complete or running off of AC with no battery installed. Amber Charging is in process. Red There is a problem with the battery. Green --- Amber Battery temperature out of thermal range; charging has stopped. Red --- Unlit No charging in process. Power Icon Blink Charging Icon Blink Off Status Indicators 1-7 Table 1-1 System Status Indications (Continued) On Green Displayed when the hard disk drive is being accessed. Off Unlit Unlit when the hard disk drive is inactive. On Green Operating in Hovering mode. Blink Green Awaiting cancellation of security. (This occurs when the computer is awaiting password input). Off Unlit Operating in normal mode. HDD Access Icon Hovering/ Security Icon 1-8 Getting Started Connectors and Peripheral Interfaces 1 Connectors and peripheral interfaces on the Stylistic LT pen tablet allow you to connect a variety of devices. Figures 1-4 and 1-5 show locations of peripheral connectors on the pen tablet. Additional features are shown for reference. PC Card Door USB Port Modem Port (optional) Figure 1-4 Speaker Figure 1-5 DC Input Reset Button Right-Side Connectors and Interfaces Headphone Jack Microphone Jack Infrared I/O Port Left-Side Connectors and Interfaces Connectors and Peripheral Interfaces 1-9 Infrared Keyboard Port Mini-dock Connector (cover removed) Charging Contacts Figure 1-6 Bottom Connectors and Interfaces Table 1-2 provides a description of each peripheral connector and interface on the Stylistic LT pen tablet. Each of the illustrated icons is embossed on the pen tablet case. Table 1-2 Connector/ Peripheral Peripheral Connectors and Interfaces Pen Tablet Icon DC Input Connector Connects an external power source such as the AC adapter or auto adapter. Infrared I/O Port No icon Microphone Jack 1-10 Purpose Getting Started An infrared transceiver built into the pen tablet allows you to communicate with other devices that are compliant with the IrDA Standard Revision 1.1. Effective range for infrared communication is about 3 feet, and within 15 degrees off of center. A clear line-of-sight path must exist between the IrDA port on the pen tablet and the IrDA transceiver on the other device. Connects an external microphone. The internal microphone is disabled when you plug in an external microphone. Table 1-2 Connector/ Peripheral Peripheral Connectors and Interfaces Pen Tablet Icon Purpose Wireless Keyboard Infrared Port An infrared receiver built into the pen tablet allows you to communicate with a wireless infrared keyboard. The keyboard infrared port works optimally between 10 to 30 cm (approximately 4 in. to 12 in.) from the keyboard infrared port, located on the bottom edge of the pen tablet. Ensure that there is a clear line-of-sight path between the infrared receiver on the pen tablet and the infrared transmitter on the keyboard. Refer to Chapter 4 for more information on the wireless keyboard. Headphone Jack Connects stereo headphones or powered external speakers. Mini-dock Connector* No icon Connects the Stylistic LT mini-dock or other approved docking device. Refer to Chapter 4 for additional information about the mini-dock. USB Port Connects Universal Serial Bus-compliant devices to the pen tablet. PC Cards Two Type II PC Cards or one Type III PC Card can be installed in the PC Card slots. Modem Port No icon This port location is used to connect a telephone line to the optional internal modem using a standard RJ-11 telephone plug. Note that the modem is available only in North American systems. Charging Contacts No icon The charge-only contacts are used when the pen tablet is installed in either the optional mini-dock or charge-only dock. Refer to Chapter 4 for more information on the mini-dock and charge-only dock. * To avoid damaging the pen tablet or your peripheral device, shut down the system or suspend system operation before connecting or disconnecting a peripheral device to this port. Connectors and Peripheral Interfaces 1-11 1-12 Getting Started Chapter 2 Using the Stylistic LT Pen Tablet This chapter covers the fundamental concepts, basic system operation and use, and system functions of the Stylistic LT pen tablet. You should familiarize yourself with this information before you attempt to operate the system. System States 2 Before you begin using the Stylistic LT pen tablet, review the different system states (or modes) that the pen tablet can use. Being familiar with these system states will help you determine whether it is appropriate to turn on, resume, suspend, or shut down the system when you begin a new session or end your current session. System behavior for each system state is described briefly in the following, with each system state listed in decreasing order of power usage: • Fully On (normal) state The system is running and the display screen is on. The system responds to the pen or other input. • Idle and Standby states Some system functions are regulated or turned off to conserve power. The display screen may be turned off. The system returns to the Fully On state when pen activity or other input is detected. • Suspend Modes: When you press the Suspend/Resume button, the system will either go into Suspend-to-RAM mode, or Save-to-Disk mode. The mode the system enters was determined when the system was configured -- usually by the reseller who sold you the pen tablet or by your IS department. Contact one of those individuals for more information on how your pen tablet is configured. ▲ Suspend-to-RAM mode When the Suspend option is set, data is saved to system RAM when the Suspend/Resume button is pressed. ▲ Save-to-Disk mode When Save-to-Disk is set (or when the Save-to-Disk hotpad key is tapped), data is written in the Save-to-Disk area on the hard disk. 2-1 • Off state All system functions are turned off to conserve power. The system does not respond to the pen or other input. The system boots at the next system power-on. Your system may be configured to enter some of these states automatically after a period of inactivity to conserve battery power. When you use the Stylistic LT pen tablet, you can change the current system state in a number of ways, depending on which state the system is in. To determine the current system state, observe the Power icon in the Status display. Table 2-1 gives the different system states represented by the Power icon and describes how you can change the system state from the current state. Table 2-1 Changing System States Power Icon Appearance To Change State* Current State Power icon displayed continuously Fully On, Idle, or Standby Power icon blinking Suspend-to-RAM† To turn the system off, shut down the system using a software shut down. To enter the Suspend-to-RAM or Save-to-Disk† state, suspend system operation using either a hardware or software suspend, or tap the Save-to-Disk hotpad. To turn the system on, resume system operation by pressing the Suspend/Resume button. To turn the system off, resume system operation, then shut down your system. Power icon not displayed Off or Save-to-Disk† To turn the system on, start your system, or resume system operation. * Information in Table 2-1 is supplied to help you understand which system states your system can enter from the current system state. Refer to the procedures on starting the system, shutting down the system, suspending system operation, and resuming system operation given later in this chapter for details on changing the current system state. † 2-2 Your system may be configured to use either Suspend-to-RAM mode, Save-to-Disk mode, or may use both modes sequentially. Using the Stylistic LT Pen Tablet Using the Pen 2 Caution The Stylistic LT pen can be damaged if used improperly. Treat the pen as you would any writing instrument. Observe the following guidelines for proper pen handling: • The pen tip is spring-loaded to provide writing comfort and to prevent screen damage. Avoid tapping it on surfaces other than the pen tablet screen. • To prevent pen loss or damage, it should be stored in the pen holder when not in use. You can use the pen to select items and run programs on the Stylistic LT pen tablet like a mouse on a desktop computer. Programs that support handwriting recognition also allow you to write characters directly on the screen with the pen. You can also use the pen as a drawing tool if your program provides a drawing or inking area on the screen. The screen reacts with the pen when the pen tip touches the screen. The pen tip generally corresponds to the left button on a two-button mouse. In order to emulate a right mouse button, tap on the right mouse button on the keypad. The pen tip automatically returns to left mouse button mode when the screen is tapped again. For more information on using the hotpads, refer to the “Using Hotpads” section later in this chapter. Here are some hints that may help you use the pen more effectively. • To move the cursor, hold the pen tip lightly on the display screen and move the pen. • To start a program, double-tap the pen tip (tap the pen tip twice rapidly) on the program icon as you would double-click a mouse. • To select an object, tap the pen tip once on the object. • To drag an object, place the pen tip directly over the object, then press and hold the pen tip against the display screen while you move the pen. Note: Installing or ejecting a PC Card while the pen is touching the screen could result in pen recognition failure. If this occurs, suspend and resume system operation one or more times, until the pen again becomes operational. Using Hovering Mode 2 Selecting the Pen Hovering icon on the Stylistic LT keypad provides the user with better cursor control. When the hovering option is enabled, the cursor can be Using the Pen 2-3 positioned over an icon without activating it. This is useful when you are performing procedures that require accurate cursor positioning, such as when simulating mouse rollover, selecting a small icon, or beginning a paint session. • To enable hovering, tap the Pen Hovering icon on the keypad. The Hovering system status indicator light illuminates green when hovering is selected. • To disable hovering, tap the Pen Hovering icon again. The Hovering system indicator light is off when hovering is not selected. Starting the Pen Tablet 2 Follow the procedure below to start the Stylistic LT pen tablet. Before you begin, confirm that the system is off. To do so, observe the Status display. If the Power icon is not lit in the Status display, the system is off and it is safe to perform this procedure. If the Power icon is lit (either blinking or on continuously), do not perform this procedure. See “System States” earlier in this chapter for details on operational modes represented by the Power icon. 1. Press the Suspend/Resume button to start the system. 2. Ensure that the battery pack in your pen tablet is sufficiently charged, or connect an external power source such as the AC adapter or auto adapter to your pen tablet. See “Status Display” in Chapter 1 to determine the percentage of charge represented by the Charging icon in the Status display. After performing system initialization, the system starts the operating system installed on the hard disk drive. Once the operating system is running, you can use the system. If you are prompted to enter your password, refer to the following section entitled “Using the Security Card”. Using the Security Card 2 The Stylistic LT can be used with an optional security card that allows you to enter an exclusive password. This ensures that only authorized persons can access a particular system and/or its hard disk drive, depending upon the selections made when the system was configured. 2-4 Using the Stylistic LT Pen Tablet Note: This feature may not be enabled, depending upon how your system is configured. Contact either your reseller or your IS department for more information on how your pen tablet is configured. Card Locator/Escape hole A B C D E F G H I J K L M N O P Q R S T U V W X Y Z * / Password input holes (A through Z, *, and / ) Card Locator/Enter hole Figure 2-1 Stylistic LT Security Card 2-2a. 2-2b. 2-2c. 2-2d. Figure 2-2 Using the Security Card Using the Security Card 2-5 When prompted by your Stylistic LT pen tablet to enter a password, perform the following procedure: 1. Ensure that the system speaker is on. Audible signals are used later in this procedure. 2. Place the security card on the display screen in a position similar to Figure 2-2a. Note that the card can be placed anywhere along the edge, as long as it is positioned with the cut corner facing the upper left. 3. Hold the card firmly against an edge of the screen frame. With your pen, tap the Card Locator/Escape hole just under the cut corner, as in Figure 2-2b. • If you hear two beeps in succession, proceed to step 4. • If you hear four beeps in succession, return to step 2. 4. With your pen, tap the Card Locator/Enter hole, as in Figure 2-2c. • If you hear two beeps in succession, proceed to step 5. • If you hear four beeps in succession, return to step 2. Note: Your password is created during system configuration. To determine your password, check with your system administrator or supervisor. 5. Tap in your password using the password input holes, as in Figure 2-2d. Up to seven characters can be used for a password (including letters and symbols). If you make a mistake while entering your password, tap the Card Locator/Escape hole, and repeat steps 2 through 4. 6. After entering your password, tap the Card Locator/Enter hole. 7. If you enter the wrong password, you receive a Setup Warning message. If this occurs, tap Continue and return to step 2. Notes: • If you have difficulty entering a password, or you move the security card while entering the password, tap the [Esc] key on the keypad until the hovering/ security LED stops blinking. At that point, begin the input procedure again. • If you enter the incorrect password three times in a row, you receive a System Disabled message, and access to the computer is disabled. If this happens, press the reset switch to restart the computer. 2-6 Using the Stylistic LT Pen Tablet Shutting Down the System 2 Follow these steps to shut down and turn off your system: 1. If system operation has been suspended, resume system operation. See “Resuming System Operation” later in this chapter for details. 2. Save your work and close all running programs. 3. Choose Shut Down from the Windows 98 Start menu and carry out the Shut Down command. The system is now in the Off state. Suspending System Operation 2 The Stylistic LT pen tablet allows you to suspend the system operation without closing programs or exiting the operating system. Use this feature to conserve battery power when a system shutdown is inconvenient. There are two different suspend modes: Suspend-to-RAM and Save-to-Disk. In Suspend-to-RAM mode, active data is saved by maintaining power to RAM while most other system components are powered off. In Save-to-Disk mode, active data is stored on the hard disk drive and power usage is reduced to the same level used in the Off state. To suspend system operation, perform one of the following procedures: • Press the Suspend/Resume button, or carry out the Suspend command from your operating system or power management program. (If your system is configured to suspend operation using Save-to-Disk mode, which is explained later in this procedure, a message is displayed while data is saved to your hard disk.) • Tap the Save-to-Disk hotpad key. Caution If you are replacing the battery pack, be sure to Save-to-Disk before you remove the battery pack. Failure to do so may result in loss of your unsaved data. The Power icon blinks when system operation is suspended-to-RAM, and is off when saved-to-disk. The state your system enters is dependent upon how your system is configured. At this point, programs that were running are stopped, active data is saved, and the system enters one of two different low-power states, or suspend modes, as explained in the following paragraphs. Shutting Down the System 2-7 4. Observe the Power icon in the Status display to determine which suspend mode your system is using. • Power icon is blinking: Suspend-to-RAM mode In this mode, active data is saved by maintaining power to RAM while most other system components are powered off. The Power icon in the Status display indicates the battery charge level. A fully charged 3-cell battery pack can maintain data in RAM for approximately 7 days; a fully charged 6-cell battery pack can maintain data for approximately 14 days. A partially charged battery pack will maintain data in RAM for proportionately less time. • Power icon is not displayed: Save-to-Disk mode In this mode, active data is stored on the hard disk drive and power usage is reduced to the same level used in the Off state. When the system is in Save-to-Disk mode, the Power icon is not visible in the Status display. In this mode, there is no danger of losing data if battery power is lost. If you have successfully performed this procedure, system operation is now suspended. Refer to “Resuming System Operation” later in this chapter to resume system operation. Also, note the following with regard to suspending system operation: • You can remove the battery pack while the system is in Save-to-Disk mode, but not Suspend-to-RAM mode (unless the AC adapter is connected). To prevent losing unsaved data, always perform Save-to-Disk before you remove the battery pack. • Your system may be configured to suspend operation automatically after a period of inactivity. • Your system may be configured to enter Save-to-Disk mode automatically after a period of time in Suspend-to-RAM mode. • The system uses a small amount of battery power when in Suspend-to-RAM mode. Eventually, the battery will become fully discharged. Note: If you will not be using the system for an extended period of time, shut down the system rather than using Suspend-to-RAM mode. • If the battery pack charge drops to the Low-Battery Warning level while the system is running, the Power icon will turn red and blink intermittently. If this occurs, suspend system operation, shut down the system, or attach an external power source, such as the AC adapter, to the pen tablet. • If the battery charge drops to the Critically Low level while the system is running, the system is forced into Suspend-to-RAM mode. If this occurs, you must connect an appropriate external power source such as the AC adapter before you can resume 2-8 Using the Stylistic LT Pen Tablet system operation. (If the battery charge drops to the Critically Low level while the system is in Suspend-to-RAM mode, the system stays in Suspend-to-RAM mode.) • Suspending system operation interrupts data communications; however, some programs may block the system from suspending to prevent an interruption. • The Suspend/Resume button on your system may be configured during system setup to act as an On-only button. If this is the case, pressing the Suspend/ Resume button will not suspend system operation as described here. Contact your IS department or reseller if your system configuration is not suitable. • If your system is equipped with a PC Card that allows you to connect to a wired or wireless network, you may be logged off the network after a period of inactivity while system operation is suspended. Contact your network administrator or local help desk for details on log-off parameters for your network. Resuming System Operation 2 To resume system operation, (from either Suspend-to-RAM or Save-to-Disk modes), press the Suspend/Resume button. • From Suspend-to-RAM mode After a few seconds, the system returns to the Fully On state and system operation resumes. Note that the display turns on shortly before the pen becomes active due to the power-up sequences observed by the system. • From Save-to-Disk mode Active data is read from the hard disk drive, and after 15 to 30 seconds, the system returns to the Fully On state. Note that power to several system components must be restored before system operation resumes. Allow sufficient time for system operation to resume before attempting to use the system. If your system uses Save-to-Disk mode, it will take longer to resume operation as compared to using Suspend-to-RAM mode. Time is needed to read data from the hard disk drive. Use the system as you normally would once system operation resumes. All programs resume at the point where execution stopped when system operation was suspended. Resuming System Operation 2-9 Using Hotpads 2 The Hotpad area consists of several pen-active “keys” on the right side of the system display that you can use to change several settings. The hotpads allow you to: • Adjust the display and speaker settings • Invoke right mouse button • Invoke hovering capability • Use as a numeric pad • Generate a Save-to-Disk request To use a hotpad key, tap directly on it with the pen. You can also press and hold the pen tip against the Volume, Contrast, and Brightness hotpad keys to automatically repeat the hotpad function. The location of each hotpad key is shown in Figure 2-3. Display Key Escape Key Save-toDisk Key ESC Cursor Keys TAB BS 7 8 9 4 5 6 1 2 3 Numeric Keys 0 Mouse Right Button Key SPACE Brightness Keys Figure 2-3 Stylistic LT Hotpad Arrays 2-10 Using the Stylistic LT Pen Tablet Hovering Key Speaker Keys Contrast Keys A summary of each hotpad’s function is given below. Note: Equivalent key codes are included for applicable hotpad keys. These can be used when a keyboard is connected. Table 2-2 Hotpad Keys Icon Name Escape Functions the same as the [Esc] key on a typical keyboard. Display Device Each time the Display Device hotpad key is tapped, the display unit is switched (in the following order): LCD -> CRT -> both LCD and CRT -> LCD... Save-to-Disk Starts the Save-to-Disk operation to save data to the disk. Cursor Control Acts in the same way as the cursor keys on a keyboard. (Up, Down, Left, and Right). Numeric Keypad Acts in the same way as the numeric keypad on a keyboard. Right Mouse Button Switches the pen function from left mouse button to right mouse button emulation. ESC TAB Description BS 7 8 9 4 5 6 1 2 3 0 SPACE Using Hotpads 2-11 Table 2-2 Hotpad Keys Icon Name Description Pen Hovering Switches the hovering mode on or off. Throughout the hovering mode, the hovering/security status indicator is lit green. Speaker Volume Down Lowers the speaker volume. Speaker Volume Up Increases the speaker volume. Speaker Volume Mute Toggles the speaker off and on. Brightness Down Decreases the luminance of the display backlight. Brightness Up Increases the luminance of the display backlight. Contrast Down Provides more contrast on CTF models only. This hotpad has no effect on TFT models. Contrast Up Flattens the contrast on the CTF models only. This hotpad has no effect on TFT models. Charging the Battery Pack 2 The Stylistic LT battery pack can be charged while it is installed in the pen tablet. To do so: 1. Connect a DC power source, such as the AC adapter, to the DC input connector on the pen tablet. The Charging icon appears in the Status display. If the battery pack charge level is below 90%, the battery pack begins charging and the Charging icon 2-12 Using the Stylistic LT Pen Tablet appears in the Status display. If the battery pack charge is 90% or higher when you connect DC power, the battery pack will not charge; this prevents overcharging the battery pack. 2. Look at the Power icon in the Status display to determine the approximate percent of charge in the battery pack. See “Status Indicators” in Chapter 1 of this manual for a description of the Power icon. As long as DC power remains connected to the pen tablet, the charging process continues until the battery pack charge reaches 100%. Charge times shown in Table 2-3 are for a fully discharged battery pack charging while the pen tablet is and is not in use. Table 2-3 Battery Pack Charging Time Approximate Charge Time (tablet not in use) Approximate Charge Time (tablet in use) 3-Cell 6-Cell 3-Cell 6-Cell 2 hours 3 hours 4 to 6 hours 8 to 12 hours Also note the following with respect to charging the battery pack: • You can use the system, suspend system operation, or shut down and turn off the system without interrupting the charging process; however, using the system while the battery pack is charging will cause the battery pack to charge at a slower rate, as noted in Table 2-3. • As noted in the procedure above, the system will not begin charging the battery pack if the battery pack charge level is 90% or higher when the system is initially connected to external DC power. (This prevents the battery pack from being overcharged.) • The Stylistic LT battery pack uses lithium ion battery cells which have no “memory effect.” You do not need to discharge the battery pack before you begin charging. Removing and Installing the Battery Pack 2 The battery pack can be removed from the pen tablet and swapped with a charged battery pack. The battery pack can then be charged in an external charger if one is available. To remove the battery pack from the pen tablet: Removing and Installing the Battery Pack 2-13 Caution The Stylistic LT pen tablet does not have a bridge battery. Prior to removing the battery pack, be sure to save your data by tapping the Save-to-Disk icon on the keypad or connect an AC adapter. Save-to-RAM will not suffice, since all data in RAM is lost when the battery is removed. 1. Choose one of the following: • Save your data by tapping on the Save-to-Disk icon on the keypad. • Close all running programs, then shut down the system. • Plug in an external DC power source. 2. Slide the battery latch to the unlocked position. (See Figure 2-4.) 3. Slide the battery pack out of the pen tablet. If you are using an external battery charger, refer to the instructions provided with the battery charger. To install the battery pack, slide the battery pack into the pen tablet until it is firmly seated. The spring-loaded battery latch automatically clicks into place. Warning To prevent pinching your fingers, keep them clear of the area between the battery pack and the pen tablet when you install the battery pack. Once the battery pack is installed, you can start your system and use the system as you normally would. 2-14 Using the Stylistic LT Pen Tablet Battery Latch Removable Battery Pack Figure 2-4 Removing and Installing the Battery Pack Conserving Battery Power 2 You can extend the charge life of your battery pack by conserving battery power. A fully charged battery pack can run the system under normal use in most applications for approximately 2 hours (standard, 3-cell battery pack) or 4 hours (extended, 6-cell battery pack). Your results may vary depending on your application and how the system is configured. Here are some suggestions to help you conserve battery power: • Use an external power source such as the AC adapter to power the system when possible. • Suspend system operation if you won’t be using the system for a few minutes. • Shut down the system if you won’t be using the system for an extended period of time. • Use power management timeouts to help you conserve power automatically. Conserving Battery Power 2-15 Modem Connection Note: 2 The optional internal 56 Kbps modem installed in some models of the Stylistic LT pen tablet* has actual transfer rates of 53 Kbps (receive), 33.6 Kbps (send), and 14.4 Kbps (fax). Download rates are limited to 53 Kbps in the United States due to FCC restrictions. * The internal modem is available as an option in North America only. The Stylistic LT pen tablet is designed to accept a standard RJ-11 telephone plug. Connect the plug to the modem jack located on the right of the pen tablet, as shown in Figure 2-5. The telephone plug can be installed whether or not the pen tablet has power applied. If you need assistance configuring the Stylistic LT pen tablet modem, contact your local help desk or your reseller. Phone Jack Modem Plug Figure 2-5 Connecting the Modem 2-16 Using the Stylistic LT Pen Tablet LAN Connection 2 Some models of the Stylistic LT have an internal LAN card that allows the computer to be connected to a high-speed LAN by 100BASE-TX Ethernet. Note: An optional Stylistic LT mini-dock (Part Number FMW29PR1) is required in order to use the LAN option. 1. To use the internal LAN, first shut the system down and unplug the AC Adapter, if necessary. 2. Install the system into the optional Stylistic LT mini-dock. Refer to Chapter 4 of this manual for instructions on use of the mini-dock. 3. Connect the AC adapter to the mini-dock, then connect the LAN cable between the mini-dock and the LAN hub, as shown in Figure 2-6. Mini-Dock AC Adapter Plug LAN Hub LAN Plug Figure 2-6 Connecting the LAN 4. To remove the LAN connector from the mini-dock, press the tab on the plug while pulling the plug away from the system. LAN Connection 2-17 PC Card Slots 2 The Stylistic LT pen tablet has two PC Card slots that allow you to install up to two Type II PC Cards using both slots 1 and 2, or a single Type III PC Card using slot 1 only. Slot 2 is closest to the screen; slot 1 is closest to the back of the system. See Figure 2-7 for PC Card slot location. Notes: • Type II PC Cards will work in either slot, with one exception: zoomed video PC Cards must be installed in slot 1. • Some PC Cards require that the system be shut down before installation. Check the user manual for your particular card before installing it. To install a PC card, position it with the label facing up and slide it through the PC card door shutters. When it is properly seated, the eject button will extend away from the computer. Flip the eject button into the eject button tray such that it is parallel with the system. To remove a PC Card from a PC Card slot, flip up the adjacent eject button so that it is perpendicular to the system, then push it in. When the PC Card pops out, carefully remove it from the slot. If you need assistance installing a PC Card in the Stylistic LT pen tablet, contact your local help desk or your reseller. Eject Buttons PC Card PC Card 2 (upper slot) PC Card 1 (lower slot) Figure 2-7 PC Card Slots 2-18 Using the Stylistic LT Pen Tablet Chapter 3 Care and Maintenance This chapter provides pointers on how to care for and maintain your Stylistic LT pen tablet. Protecting the Display Screen 3 The Stylistic LT pen tablet is designed to provide you with years of service. Using a screen protector will help ensure that the screen remains as clear as possible. When installed, the screen protector becomes a durable, replaceable, antiglare writing surface that protects the display screen from abrasion. To obtain additional screen protectors use Fujitsu part number FMWSP8 (12-pack) when ordering. Additional information about installation is included with the screen protectors. Caution During normal use of the pen tablet, small particles from the environment can become embedded in the pen tip and scratch the screen. To prevent scratching the screen, ensure that a screen protector is installed before using your pen tablet. The warranty does not cover a screen that is scratched as a result of not using a screen protector. To install a new screen protector on your pen tablet: 1. If a screen protector is already installed on the display screen, remove it before installing the new screen protector. The screen protector is held onto the display screen surface by a thin strip of adhesive around the edges. A notch in one corner of the screen protector allows you to slide your fingernail under the screen protector for easy removal. 2. Clean the adhesive residue from the screen surface by gently wiping the residue using a soft cotton cloth dampened with denatured alcohol. Ensure that all film has been removed from the screen before applying a new screen protector. 3-1 Cautions • Cleaning the screen surface with denatured alcohol may result in streaking. If streaking occurs, buff the screen surface lightly with a soft, dry cloth. • The Stylistic LT pen tablet is not waterproof. Do not pour liquids on the system or wash it with a soaked cloth. 3. Remove the protective coating from the adhesive side of the new screen protector first. 4. Apply the screen protector to the display screen surface. When doing so, orient the screen protector with the adhesive side of the screen protector facing the display screen and the notched corner of the screen protector toward the lower left corner of the display screen. 5. Remove the protective plastic cover from the face of the screen protector. 6. Apply pressure to the screen protector with your finger using a continuous wiping motion along the edges. The adhesive sets completely within 48 hours. To ensure a good seal between the screen protector and the display, do not lift the screen protector from the display once it has been applied. 7. Clean any residue left behind by the protective coating from the exposed surface of the screen protector by wiping gently with a soft cotton cloth dampened with denatured alcohol. Wipe the screen protector with a soft dry cloth to remove any low-tack adhesive; this will help to prevent the pen tip from squeaking. The screen protector is now installed. Storing the Stylistic LT Pen Tablet Store the Stylistic LT pen tablet in the Fully Off state with a fully charged battery pack installed. The Stylistic LT battery pack always provides power to some system components, even when the system is in the Fully Off state. If you plan to store the system with the battery pack removed, be sure to Save-to-Disk prior to storing; failure to do so could result in lost data. You can store the pen tablet for about 14 days (standard 3-cell battery pack) or 25 days (extended 6-cell battery pack) with a fully charged battery pack installed. After this period, the battery pack should be recharged or replaced with a charged battery pack. 3-2 Care and Maintenance 3 Protecting the Stylistic LT Pen Tablet in Harsh Environments 3 The Stylistic LT pen tablet is designed for use in environments where there is no direct exposure to rain, mist, sprays, dirt, or other abrasive particles. The optional Stylistic LT harsh environment case (FMWCC39) and the Stylistic LT screen protector (FMWSP8) provide some protection in these environments, as well as from physical damage due to shock or vibration. Note that the harsh environment case does not render the pen tablet waterproof, dustproof, or submersible. The pen tablet is easily used while installed in the harsh environment case. For additional information on the Stylistic LT harsh environment case as well as additional carrying cases, portfolio cases, and holsters, contact your reseller. Avoiding Overheating 3 The Stylistic LT pen tablet monitors its internal temperature. As the internal temperature approaches the tolerable limits of heat-sensitive components, system functions are automatically limited or turned off to prevent heat damage. To avoid overheating the pen tablet, do not charge the pen tablet while it is in the harsh environment case unless the system is either suspended or off. Using proper power management techniques while the pen tablet is in the harsh environment case also helps to prevent overheating. Cleaning the Display Screen 3 To clean the pen tablet display screen, wipe the screen surface gently using a soft cotton cloth slightly dampened with water or denatured alcohol. Using denatured alcohol may resulting in streaking. If this occurs, gently buff the surface with a soft, dry cloth. Caution The Stylistic LT pen tablet is not waterproof. Do not pour liquids on the pen tablet or wash the pen tablet with a heavily soaked cloth. Protecting the Stylistic LT Pen Tablet in Harsh Environments 3-3 Calibrating the Pen 3 You calibrate the pen to adjust the cursor position on the screen relative to the position of the pen tip. If the cursor is not displayed under the pen tip when you use the pen, you should calibrate the pen. Pen calibration may be required due to the following situations: • The previous user of the Stylistic LT pen tablet writes with the opposite hand. • The system has been in use for some time and the pen has not been recalibrated. To Calibrate the Pen 3 1. In the Control Panel, double-tap the Pen Configuration icon. Select the Calibration property sheet, then click on Pen Calibration. 2. Position the Stylistic LT pen tablet as you normally would during use. Be sure to hold the pen at the angle that you regularly use. Touch the screen only with the pen tip; if you inadvertently touch the screen with your finger or hand during the calibration process, faulty calibration may result. 3. Perform the calibration steps according to the instructions on the screen. The calibration utility displays a cross-hair symbol in each corner of the screen, one corner at a time. Hold the pen as you normally would while using the system and, as accurately as possible, tap the center of each crosshair as it is displayed. A dialog box is displayed after you tap the last of the four cross-hair symbols. 4. In the dialog box, tap your response. (If you do not tap any of the buttons within 20 seconds, your new calibration settings are discarded and previous calibration settings are used.) • If you are satisfied that you tapped the cross-hairs accurately, tap OK. The taps that you performed in step 3 are then used to calibrate the screen. • If you do not want to use your taps to calibrate the screen, tap Cancel. • If you want to try again, tap Recalibrate. The calibration instructions reappear. If you have successfully performed the procedure above, the pen is now calibrated, and you can use the system as you normally would. 3-4 Care and Maintenance Replacing the Pen 3 With use, the pen tip may become worn or may pick up abrasive particles that can scratch the screen. A damaged or warped tip may not move freely, causing unpredictable results when using the pen. If your pen exhibits any of these problems, replace the pen. Replacing the Pen 3-5 Solving Problems 3 Solutions to some common problems are described in the following sections. If you are experiencing a problem with your Stylistic LT pen tablet that you cannot solve by taking the actions described, contact your local help desk or your reseller for further assistance. System Will Not Resume Operation 3 If the system will not resume operation after system operation has been suspended, check the following possible causes: • The battery pack may be either defective or discharged to a critically low level. When the battery pack reaches the critically low level, the system is forced into Suspend-to-RAM mode to avoid a total system power failure. To correct this problem, connect an external power supply (such as the AC adapter). • The system may be at the critical thermal limit. To avoid damage to heat-sensitive components, the system enters Suspend-to-RAM mode when it gets too hot. System operation cannot be resumed until the pen tablet cools off to a tolerable temperature. Move the pen tablet to a cooler location and prevent direct sunlight from shining onto the pen tablet. Display Screen Is Blank or Difficult to Read 3 If the display screen on your Stylistic LT pen tablet appears blank or is unreadable, confirm that the system is running (the Power LED is displayed continuously on the Status display), and check the following: • The system brightness may be set too low, causing the screen to appear too dark. Use the brightness hotpad to adjust the screen brightness. • An external monitor may be selected. Tap on the Display Select hotpad to determine whether the pen tablet display screen is selected. • The video timeout may have expired. Tap on the display screen to reactivate the display. Note that this is a normal, power-saving feature. • Transflective (CTF) systems only: The display contrast settings may be set to extreme high or low level causing the screen to appear blank. Try adjusting the contrast setting using the hotpads. Note that the surrounding temperature will affect the display contrast. You may need to adjust the contrast periodically to compensate for changes in environment temperature. 3-6 Care and Maintenance Infrared Data Transfer Is Not Working Note: 3 For troubleshooting problems between the Stylistic LT and the optional wireless keyboard, refer to the section of Chapter 4 entitled “Encountering Problems when Using the Wireless Keyboard.” If you are experiencing problems transferring data over the system’s infrared interface, check the following: • Can the IrDA port on the pen tablet “see” the IrDA port on the other device? A direct line-of-sight path must exist between the IrDA port on the pen tablet and the IrDA port on the other device. • The distance between the two devices must not be more than approximately 3 feet or 1 meter. • The center line of the IrDA port on the pen tablet must not be more than 15 degrees from the center line of the IrDA port on the other device. • The device with which you are trying to communicate must be compliant with the IrDA Standard Revision 1.0 or 1.1. Pen Tablet Is Not Responding to the Pen 3 If your pen tablet is not responding to the pen, connect an external keyboard (either wired or wireless) to the system to see if it responds to keyboard commands. If the system doesn’t respond to the keyboard, the application or system may have crashed, and it may be necessary to reset the system. Note that the optional mini-dock is required to connect a wired keyboard. Cursor Is Not Tracking Pen 3 If the cursor on the screen is not accurately tracking the pen or appears to be misaligned with the pen, calibrate the pen. See “Calibrating the Pen” earlier in this chapter for details. Solving Problems 3-7 Audio Volume Is Too Low 3 If the audio volume on your pen tablet speaker or external headphones is too low, check the following: • Ensure that the speaker (or headphone output if using headphones) is enabled. To do so, tap the Speaker Mute hotpad. The system beeps when the speaker or headphone output is turned on using the Speaker Mute hotpad. • Ensure that the volume level set with the Volume hotpads is set to an audible level. • Ensure that the mute box in the system volume control (accessible from the system tray) is not set. • Ensure that any volume control in your audio software is set to an audible level. Configuring Peripherals Interfaces 3 Note that peripheral devices such as serial port A can be disabled during the BIOS Setup. If the peripheral interface you want to use does not appear to be working with your peripheral device, ensure that it is enabled in the BIOS. Contact your local help desk or reseller if you need assistance using BIOS Setup. 3-8 Care and Maintenance Chapter 4 Using the Optional Peripherals Several custom options are available to support your Stylistic LT pen tablet, as listed in the “Optional Accessories” section of Chapter 1. This chapter contains information to assist you in using three of the more complex peripherals: the Mini-Dock (FMW29PR1), the Charge-Only Dock (FMW29CR1), and the Wireless Keyboard (North America: FMWKB4A, United Kingdom: FMWKB4B, Germany: FMWKB4D, and France: FMWKB4F). Note: Each of the optional items is delivered with instructions on its use. The information contained in this chapter is provided as a quick reference for three of the more commonly used peripherals. Stylistic LT Mini-Dock 4 The Stylistic LT mini-dock is designed to extend the connectivity of your pen tablet by providing a number of ports that are not available on the system. Refer to Figures 4-1, 4-2, and 4-3 for port locations. The mini-dock can also be used as a charging dock for periods when the pen tablet is not being used. The Stylistic LT mini-dock provides the following interfaces: • PS/2-style Mouse Port Used for connecting a mouse with a PS/2-style connector. • AC Adapter Port Used for connecting the AC adapter to supply power to the system. • Parallel Port Ordinarily used for connecting a printer. • Serial Port Used for connecting a serial device. • Video Port Used for connecting a video monitor for displaying the contents of the Stylistic LT screen. • Floppy Disk Drive Port Used for connecting the optional floppy disk drive (FMWFD2). Stylistic LT Mini-Dock 4-1 • PS/2-style Keyboard Port Used for connecting a keyboard with a PS/2-style connector. • LAN Port Used for connecting the pen tablet’s optional internal LAN card to a LAN hub. Note: The LAN port can only be used with systems that have been pre-configured with the optional internal LAN card. The mini-dock is required in order to use the LAN card; there is no LAN port on the pen tablet. Stylistic LT Pen Tablet Floppy Disk Drive FMWFD2 Stylistic LT Mini-Dock PC Card Video Monitor PS/2-Style Keyboard PS/2-Style Mouse Printer Figure 4-1 Mini-Dock Peripheral Interfaces The viewing angle of the mini-dock can be adjusted to four different positions. The bottom of the support bail on the rear of the support platform (see Figure 4-3) snaps into one of four slots. When storing the mini-dock, flip the bail up against the back of the support platform to allow the platform to lie flat. 4-2 Using the Optional Peripherals AC Adapter Port LAN Port PS/2-style Mouse Port Figure 4-2 Right-Side of Stylistic LT Mini-Dock Support Platform Support Bail PS/2-style Keyboard Port Parallel Port Serial Port Video Port Floppy Disk Drive Port Figure 4-3 Rear and Left-Side of Stylistic LT Mini-Dock Stylistic LT Mini-Dock 4-3 Installing the Stylistic LT into the Mini-Dock 4 Cautions • Dropping conductive material onto the charging contacts could result in internal damage to the pen tablet circuitry. • Prior to installing the Stylistic LT into the mini-dock, be sure to disconnect the AC adapter first. Failure to do so could result in damage to the system or the mini-dock. 1. Shut down the system and disconnect the AC adapter, if used. 2. Position the pen tablet against the positioning guide and the back of the mini-dock. 3. Slide the pen tablet into the tray at the bottom of the mini-dock and press it down firmly until it is seated, as shown in Figure 4-4. The alignment guide in the bottom of the tray ensures that the system is properly seated over the connector. 4. Connect the AC adapter to either the pen tablet or mini-dock and re-start your system. Stylistic LT Pen Tablet Positioning Guide Stylistic LT Mini-Dock Mini-Dock Base Figure 4-4 Installing the Stylistic LT in the Mini-Dock 4-4 Using the Optional Peripherals Removing the Stylistic LT from the Mini-Dock 4 1. Shut down the system and disconnect the AC adapter from the mini-dock or pen tablet, if required. 2. While holding the base of the mini-dock with one hand, grasp the pen tablet at the top and firmly pull it straight up from the base. 3. Reconnect the AC adapter and restart your system. Stylistic LT Charge-Only Dock 4 The Stylistic LT charge-only dock is designed to allow you to use the pen tablet on your desktop as it charges from the AC adapter. The charge-only dock is the same size as the mini-dock, but the AC adapter plug is the only connector on the dock. AC Adapter Port Figure 4-5 Inserting Stylistic LT into Charge-Only Dock The viewing angle of the charge-only dock can be adjusted to four different positions. The bottom of the support bail on the rear of the support platform (see Figure 4-6) fits into one of four slots. When storing the dock, flip the bail up against the back of the support platform to allow the platform to lie flat. Stylistic LT Charge-Only Dock 4-5 Support Bail Support Platform Figure 4-6 Charge-Only Dock Support Bail Installing the Stylistic LT into the Charge-Only Dock 4 Caution • Dropping conductive material onto the charging contacts could result in internal damage to the pen tablet circuitry. • Prior to first installing the Stylistic LT into the charge-only dock, be sure to disconnect the AC adapter from the dock. Failure to do so could result in damage to the system or the dock. 1. Position the pen tablet against the positioning guide and the back of the charge-only dock. 2. Slide the pen tablet into the tray at the bottom of the dock and press it down firmly until it is seated, as shown in Figure 4-5. The alignment guide in the bottom of the tray ensures that the system is properly seated over the charging pins. Removing the Stylistic LT from the Charge-Only Dock 4 1. Disconnect the AC adapter from the charge-only dock or pen tablet, if required. 2. While holding the base of the dock with one hand, grasp the pen tablet at the top and firmly pull it straight up from the base. 4-6 Using the Optional Peripherals Stylistic LT Wireless Keyboard 4 The wireless keyboard allows you to transmit between the Stylistic LT and the keyboard using infrared rays. Using the Wireless Keyboard 4 There are several key points to remember when using the wireless keyboard: • The pen tablet should be securely seated upright, either in a mini-dock, charge-only dock, or portfolio carrying case. • The keyboard should be positioned so that its infrared transmitter is directly facing the infrared photosensor on the pen tablet (see Figure 4-7). Pen Tablet Infrared Photosensor Wireless Keyboard Infrared Transmitter Figure 4-7 Keyboard-to-Stylistic LT Wireless Transmission • The keyboard performs optimally when it is within 30 cm (approximately 12 inches) of the pen tablet, although it will operate at greater distances. • Do not attempt to use a wireless keyboard at the same time as a wired keyboard (via the PS/2-style connector on the mini-dock). The wired keyboard takes precedence over the wireless, so the wireless keyboard becomes disabled. • If a key on the keyboard is depressed continuously, the battery will automatically shut off after approximately 60 seconds. Stylistic LT Wireless Keyboard 4-7 Entering an Identification Code 4 When multiple keyboards and pen tablets are used in a small area, it may be necessary to assign an individual identification code to each keyboard/pen tablet pair. Assigning identification codes prevents interference or “cross-talk” between closely situated keyboards and systems. The identification code assigned to a keyboard/pen tablet pair is temporary. The code is cancelled whenever the computer is turned off, suspended, or reset. When the system is initially turned on, the pen tablet identification code defaults to 0 (zero). At that point, any keyboard will work with the pen tablet until a new code is entered via a keyboard. Once a new code is entered, only the coded keyboard will work with the pen tablet unless other keyboards are individually coded with the same identification code. The system will recognize the code of the first keyboard with which it is used; other keyboards will not be recognized unless they are assigned the same code as the first keyboard used. For example, if two keyboards (A and B) are within infrared range of the pen tablet, they can both be used when the system is initially reset or suspended. If the identification code for keyboard A is set to 123 and it is used with the pen tablet first, the pen tablet will recognize 123 as the code; keyboard B would be disabled unless you enter 123 as its code. If you assign keyboard A the identification code 123, but use keyboard B first, the pen tablet will only recognize keyboard B (with the default code of 0). To enter an identification code for your keyboard, perform the following steps: Note: In the following step, be sure to press and hold down the keys in the same order as they appear below, and leave them depressed until after the code is entered. There is no on-screen indication that the code has been entered. 1. Press [Fn]+[Left Alt]+[Left Shift]+[ID Code]. Use up to seven keys for the ID Code, consisting of number characters 0 through 7. Encountering Problems when Using the Wireless Keyboard The wireless keyboard is used in the same way as a normal wired keyboard. In typical operation, you should encounter few problems in transmitting data to your pen tablet. If your keyboard fails to perform properly, check for the following circumstances: 4-8 Using the Optional Peripherals 4 • The infrared transmitter on the keyboard is not properly aligned with the pen tablet infrared photosensor. • The keyboard is too far from the pen tablet, or something is obstructing the line-of-sight between the ports. • The remote control for another device (such as a television or wireless headphones) is being operated in the same vicinity as the keyboard. • The infrared transmitter on the keyboard and/or the infrared photosensor on the pen tablet are directly exposed to sunlight or bright artificial light. • The infrared transmitter on the keyboard and/or the infrared photosensor on the pen tablet are dirty. • The keyboard batteries are dead (see the section of this chapter entitled “Replacing the Wireless Keyboard Batteries”). • The keyboard may not have the correct identification code entered for the system with which it is being used (see the section of this chapter entitled “Entering an Identification Code”). Replacing the Wireless Keyboard Batteries 4 Occasionally the batteries in the wireless keyboard will require replacement. The keyboard uses two AAA-size alkaline batteries. Caution • Ensure that the correct polarities (+ and -) are used when installing new batteries in the keyboard. • Don’t mix old and new batteries. • If the keyboard won’t be used for a long period, remove the batteries to prevent electrolyte leakage. If the batteries leak, clean out the battery compartment with a damp cloth, then dry thoroughly. • Handle the batteries carefully, and dispose of old batteries in accordance with local regulations. Stylistic LT Wireless Keyboard 4-9 To replace the batteries in your wireless keyboard: 1. Close any open programs on your pen tablet. 2. Remove the wireless keyboard battery compartment cover by pinching the latch towards the cover, then pulling the cover away from the keyboard, as in Figure 4-8a. 3. Remove the old batteries and dispose of them in accordance with local regulations. 4. Insert two new AAA-type alkaline batteries into the battery tray. Be sure to observe correct polarity, as shown in Figure 4-8b. 5. Replace the battery compartment cover. a. Latch Battery Compartment Cover b. - ++ Figure 4-8 Replacing the Wireless Keyboard Batteries 4-10 Using the Optional Peripherals Appendix A Agency Notices FCC Notices 4 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. Changes or modifications not expressly approved by Fujitsu Personal Systems, Inc., could void the user’s authority to operate the equipment. Notice to Users of Radios and Television 4 These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If the equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet that is on a different circuit than the receiver. • Consult the dealer or an experienced radio/TV technician for help. Shielded interconnect cables must be employed with this equipment to ensure compliance with the pertinent RF emissions limits governing this device. Notice to Users of the U.S. Telephone Network Note: 4 Some configurations of the Stylistic LT do not have an internal modem. The following information applies only to those systems with an internal modem. The Stylistic LT pen tablet is supplied with an internal modem which complies with Part 68 of the FCC rules. On the pen tablet is a label that contains the FCC Registration Number and Ringer Equivalence Number (REN) of this system, along Agency Notices A-1 with other information. If requested, users must provide their telephone company with the following information: • The telephone number to which the pen tablet is connected • The Ringer Equivalence Number (REN) for this equipment • The information that the system requires a standard modular jack type USOC RJ-11C which is FCC Part 68-compliant • The FCC Registration Number This equipment is designed to be connected to the telephone network or premises wiring using a standard modular jack type USOC RJ-11C which is FCC Part 68-compliant. The REN is used to determine the number of devices you may connect to your telephone line and still have all those devices ring when your number is called. Too many devices on one line may result in failure to ring in response to an incoming call. In most, but not all, areas, the sum of all of the devices should not exceed five (5). To be certain of the number of devices you may connect to your line, as determined by the RENs, contact your local telephone company. If this equipment causes harm to the telephone network, your telephone company may discontinue your service temporarily. If possible, they will notify you in advance. If advance notice is not practical, they will notify you as soon as possible. You will also be advised of your right to file a complaint with the FCC. This fax modem also complies with fax branding requirements per FCC Part 68. If you experience trouble with this equipment, please contact your support representative. Your telephone company will probably ask you to disconnect this equipment from the telephone network until the problem is corrected and you are sure that the equipment is not malfunctioning. This equipment may not be used on coin service telephones provided by your telephone company. Connection to party lines is subject to state tariffs. Contact your state’s public utility commission, public services commission, or corporation commission for more information. FCC rules prohibit the use of non-hearing aid compatible telephones in the following locations or applications: A-2 Appendix • All public or semipublic coin-operated or credit card telephones. • Elevators, highways, tunnels (automobile, subway, railroad, or pedestrian) where a person with impaired hearing might be isolated in an emergency. • Places where telephones are specifically installed to alert emergency authorities such as fire, police, or medical assistance personnel. • Hospital rooms, residential health care facilities, convalescent homes, and prisons. • Workstations for the hearing impaired. • Hotel, motel, or apartment lobbies. • Stores where telephones are used by patrons to order merchandise. • Public transportation terminals where telephones are used to call taxis or to reserve lodging or rental cars. • In hotel and motel rooms at least ten percent of the rooms must contain hearingaid compatible telephones that will be provided to hearing impaired customers on request. DOC (Industry Canada) Compliance Notices 4 This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set forth in the radio interference regulations of the Canadian Department of Communications. Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de classe B prescrites dans le règlement sur le brouillage radioélectrique édicté par le Ministère des Communications du Canada. Notice to Users of Radios and Television 4 This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment regulations. Cet appareil numérique de la classe B respecte toutes les exigences du règlement sur le matériel brouilleur du Canada. Notice to Users of the Canadian Telephone Network 4 The Canadian Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, Agency Notices A-3 operational, and safety requirements. The Department does not guarantee the equipment will operate to the user’s satisfaction. Repairs to telecommunication equipment should be made by a Canadian authorized maintenance facility. Any repairs or alterations not expressly approved by Fujitsu Personal Systems, Inc. or any equipment failures may give the telecommunications company cause to request the user to disconnect the equipment from the telephone line. The connecting arrangement code for this equipment is CA11A. The Load Number is 0.2. The Load Number assigned to each telephone terminal device denotes the percentage of the total load to be connected to a telephone loop or circuit to be used by the device to prevent overloading. The termination on a loop may consist of any combination of devices such that the total of the load numbers of all devices does not exceed 100. Caution For safety, users should ensure that the electrical ground of the power utility, the telephone lines, and the metallic water pipes are connected together. Users should not attempt to make such connections themselves but should contact the appropriate electric inspection authority or electrician. This may be particularly important in rural areas. Avis Aux Utilisateurs Du Réseau Téléphonique Canadien 4 L’étiquette canadienne Industrie Canada identifie l’équipement certifié. Cette certification signifie que l’équipement satisfait certaines normes de protection, d’exploitation et de sécurité des réseaux de télécommunications. Le département ne garantit pas le fonctionnement de l’équipement à la satisfaction de l’utilisateur. Le Stylistic LT possede un modem interne conforme aux normes de certification d’Industrie Canada pour protéger les réseaux de télécommunications et satisfaire aux normes de sécurité. Avant de connecter cet équipement à une ligne téléphonique, l’utilisateur doit vérifier s’il est permis de connecter cet équipement aux installations de télécommunications locales. L’utilisateur est averti que même la conformité aux normes de certification ne peut dans certains cas empêcher la dégradation du service. A-4 Appendix Les réparations de l’équipement de télécommunications doivent être effectuées par un service de maintenance agréé au Canada. Toute réparation ou modification, qui n’est pas expressement approuvée par Fujitsu Personal Systems, Inc., ou toute défaillance de l’équipement peut entrainer la compagnie de télécommunications à exiger que l’utlilisateur déconnecte l‘équipement de la ligne téléphonique. Le code d’arrangement de connexion de cet équipement est CA11A. Le numéro de charge est 0.2. Le numéro de charge assigné à chaque terminal téléphonique indique le pourcentage de la charge totale pouvant être connecté à une boucle ou à un circuit téléphonique, utilisé par ce périphérique afin de prévenir toute surcharge. La terminaison d’une boucle peut être constituée de n’importe quelle combinaison de périphériques de sorte que le total de numéros de charge de tous les périphériques n’excède pas 100. Avertissement Pour assurer la sécurité, les utilisateurs doivent vérifier que la prise de terre du service d’électricité, les lignes téléphoniques et les conduites d’eau métalliques sont connectées ensemble. Les utilisateurs NE doivent PAS tenter d’établir ces connexions eux-mêmes, mais doivent contacter les services d’inspection d’installations électriques appropriés ou un électricien. Ceci peut être particulièrement important en régions rurales. Agency Notices A-5 A-6 Appendix Index A AC Adapter port, 4-1 Auto Adapter, 1-2 B battery charger, external, 1-2 battery gauge, 2-13 battery latch, 1-4 battery pack 3-cell, 1-2 6-cell, 1-2 charging, 2-12 charging time, 2-13 critically low level, 2-8, 2-9 low-battery warning, 2-8 no memory effect, 2-13 overcharge protection, 2-13 removing and installing, 2-13, 2-14 storing in system unit, 3-2 will not begin charging, 2-13 battery power conserving, 2-15 used in suspend-to-RAM mode, 2-8 brightness, 2-10 hotpads, 2-10 configuring peripherals interfaces, 3-8 connectors and peripheral interfaces, 1-9 conserving battery power, 2-15 contrast hotpads, 2-10 critically low battery level, 2-8, 2-9 cursor moving with pen, 2-3 not tracking pen, 3-7 cursor key hotpad, 2-10 D DC input connector, 1-4, 1-10 determining suspend mode, 2-8 display screen is blank, 3-6 screen, cleaning, 3-3 display area, 1-3 display select hotpad, 2-10 dragging an object, 2-3 E eject buttons, 1-5 external battery charger, 1-2 external floppy disk drive, 1-2 C F Calibrating, 3-4 calibrating the pen, 3-4 care and maintenance, 3-1 carrying case, 1-2 charge-only contacts, 1-11 charge-only cradle, 1-2, 4-5 installing the Stylistic LT, 4-6 removing the Stylistic LT, 4-6 charging icon, 1-7 charging the battery pack, 2-12 cleaning the display screen, 3-3 compact desk stand, 1-2 floppy disk drive port, 4-1 folding desk stand, 1-2 Fully On, 2-1 H hard disk drive access icon, 1-8 harsh environment case, 1-2, 3-3 headphone jack, 1-3, 1-11 holster, 1-2 hotpad area, 1-3 hotpads, using, 2-10 Index-1 hovering key hotpad, 2-10 hovering mode, 2-3 disabling, 2-4 hovering/security icon, 1-8 I icons, 1-7 charging, 1-7 HDD access, 1-8 hovering/security, 1-8 power, 1-7 identification code, wireless keyboard, 4-8 Idle or Standby state, 2-1 infrared data transfer not working, 3-7 infrared keyboard port, 1-11 interfaces connectors and peripherals, 1-9 IrDA port, 1-3, 1-10 ports, 4-1 removing the Stylistic LT, 4-5 using, 4-1 mini-dock connector, 1-11 Modem, 1-11, 2-16 modem port, 1-5 modem, internal, 1-1 N numeric key hotpad, 2-10 O Off state, 2-2, 2-7 operating systems, 1-1 optional accessories, 1-2 optional peripherals using, 4-1 overheating, avoiding, 3-3 K Keyboard, 4-7 keys brightness, 2-12 contrast, 2-12 cursor control, 2-11 display device, 2-11 escape, 2-11 numeric keypad, 2-11 pen hovering, 2-12 right mouse, 2-11 save-to-disk, 2-11 speaker volume, 2-12 L LAN connection, 2-17 LAN port, 4-2 LAN, internal, 1-1 low-battery warning, 2-8 M microphone jack, 1-3, 1-10 mini-dock, 1-2 installing the Stylistic LT, 4-4 Index-2 P parallel port, 4-1 PC Card, 1-11, 2-18 door, 1-5 pen, 1-2, 1-3 calibrating, 3-4 cautions, 2-3 moving cursor with, 2-3 not responding, 3-7 replacing, 3-5 selecting object with, 2-3 using, 2-3, 2-12 peripheral connectors, 1-9, 1-10 portfolio case, 1-2 power icon, 1-7, 2-2 blinking, 2-2, 2-8 not displayed, 2-2 Power On, 1-7 power usage, 2-1 problems, solving, 3-6 protecting the display screen, 3-1 protecting the Stylistic LT in harsh environments, 3-3 PS/2-style keyboard port, 4-2 PS/2-style mouse port, 4-1 R removable battery pack, 1-4 reset button, 1-4 resuming system operation, 2-9, 3-6 right mouse button hotpad, 2-10 S Save-to-Disk hotpad, 2-10 Save-to-Disk mode, 2-1, 2-7, 2-8, 2-9 screen protectors, 1-2 security card, 1-2 using, 2-4 selecting an object with the pen, 2-3 serial port, 4-1 shutting down the system, 2-7 slipcase, 1-2 solving problems, 3-6 Speaker, 1-3 speaker mute hotpad, 2-10 starting a program, 2-3 starting the system, 2-4 status display, 1-6 charging icon, 1-7 HDD access icon, 1-8 hovering/security icon, 1-8 indicators, 1-3 power icon, blinking, 2-2 power icon, system states indicated by, 2-2 status display power icon, 1-7 Storing, 3-2 Stylistic LT care and maintenance, 3-1 features, 1-3, 1-4, 1-5 items included with, 1-1 optional accessories, 1-2 protecting, 3-3 resuming operation, 2-9 shutting down, 2-7 starting, 2-4 storing, 3-2 suspending operation, 2-7 using, 2-1 suspend modes save-to-disk, 2-1 Suspend-to-RAM, 2-1 Suspend/Resume button, 1-4, 2-4 disabled, 2-9 suspending system operation, 2-7 Suspend-to-RAM mode, 2-8, 2-9 Suspend-to-RAM mode, 2-1 system states, 2-1, 2-2 changing, 2-2 system will not resume operation, 3-6 T troubleshooting, 3-6 audio too low, 3-8 infrared not working, 3-7 pen not responding, 3-7 pen not tracking cursor, 3-7 screen is blank, 3-6 system will not resume operation, 3-6 turning off the system, 2-7 turning on the system, 2-4 U USB port, 1-5, 1-11 using the pen, 2-12 using the Stylistic LT, 2-1 V video port, 4-1 volume hotpads, 2-10 W Windows, 1-1 Windows 98, 1-1 wireless keyboard, 1-2, 4-7 batteries, replacing, 4-9 entering an identification code, 4-8 troubleshooting, 4-8 using, 4-7 wireless keyboard port, 1-3 Index-3