Transcript
FocalpointNet Single-User Using DSL or Cable Modem
T_03
This diagram depicts a typical FocalpointNet Single-User Workstation with one ADP ticket and one itinerary printer, and one MIR device. (Printers/Mir devices are optional)
Ticket Printer
Itinerary Printer
Parallel
Mir Device (optional)
(DB25M) To Com 1 or 2 (DB9S)
I
R
S
Single-User Workstation w/ FPM and internal modem Telco DSL line or Cable connection
DSL or CABLE MODEM
K
E
Com1 (DB9S)
LPT1 (DB25M)
Com2 (DB9S)
on board Ethernet
Itinerary Printer (serial) R (DB25M)
CABLE LEGEND Cables marked with one of the following symbols are Automatically shipped by GI with the equipment
The Itinerary Printer will be connected serial to COM2, unless there is a MIR device. In that case, the Itin will be parallel and connected to LPT1.
Must be ordered Must be validated, may need parts ordered Customer/Vendor supplied Dotted line indicates alternate cabling method or optional device
10_22_fpnet_dsl_single.vsd
sh
1
FocalpointNet Single-User DSL or Cable Modem
T_03
CABLES - NOTE: Equipment placement must take into account the cable lengths specified below, e.g., the Workstation must be placed within 6ft of the DSL/Cable modem; Modem within 6 ft of DSL or Cable demarc. E = Cat5 cable, (Refer to cabling diagrams). I = Local Parallel Printer cable: 10' - 949323, 10' extension; 949324 K= RJ45 to RJ45 phone cord.Attaches dedicated Telco Demark to modem (dsu,dsl, etc.) Can either be provided by the manufacturer or can use 8' PN-949387 or 25' PN-949447 R = FPNet Workstation COM port DB9F to serial printer DB25M: plenum, 30' - 951396, 50' -951397, 100' - 951398 , 150' - 951767 S = Wingate Workstation COM port DB9F(labeled FP) to TS2000/Globalware MIR PC Com port DB9F (labelled Globalware): plenum, 30' - 951594, 50' - 951595, 100' - 951596 , 150' - 951766. Note: If a customer's MIR device requires a 25 pin connector, a 9 pin Male to 25 pin Female adapter, PCN 949554, must be ordered. If the customer supplies the PC, and if not using Globalware, the customer is responsible for the cable. POWER REQUIREMENTS: (locate outlets within 4 ft of devices) 1. One dedicated, 110V duplex (2) outlet for EACH Workstation/montor or MIR PC. 2. One dedicated, 110V duplex (2) outlet for each printer. One duplex may be used for two printers if within 4 ft. 3. One dedicated 110V outlet for DSL/ Cable Modem. EQUIPMENT SPECS: - Workstation/Mir PC: Typically about 22" high x 18" wide x 30" deep. Wt = 65 lbs, 110V, 150 watts (PC) and 100 watts (Monitor), 1200 BTU total. - ADP Floor Model Printer - 30" high x 13" wide x 32" deep. WT 85 to 154lbs, 110V, 370 Watts, 3.5 Amps, 1258 BTU. requires approximately 6 square feet (2 ft wide by 3 ft deep) of floor space. The printer is on casters, and can be pulled out to obtain access to the door if required. - ADP DeskTop Printer - 20" high x 11" wide x 32" deep. WT 78lbs, 110V, 370 Watts, 3.5 Amps, 1258 BTU. Requires approx 22" clearance on right side to open the stock bin door. - Lexmark 2380 Plus Itin Printer - 8" high x 20"w x 12" deep. Wt 20 lbs, 110V, 120 Watts, 409 BTU-Max. No stand provided by GI. Requires desktop space, forms feed from front and below printer. Parallel standard, shipped with serial adapter. - TI810 printer - 36" high (incl stand) x 28" wide x 22" deep. Wt 55lbs, 110V, .9 Amps, 108 Watts, 367 BTU. Requires approximately 9 square feet (3 ft wide by 3 ft deep) of floor space. - Okidata 320 printer (desktop) - 5" high x 16" wide x 14" deep. WT 16 lbs, 110V, .9 amps, 108 Watts. Requires approx 4 square feet of desk space ( 2 ft x 2 ft) for printer and paper. 10_22_ fpnet_dsl_single.vsd
2
