Transcript
M2M HSPA Smart Telemetry Solution: MA-3010S
CHOOSE WELL... CHOOSE WISELY... CHOOSE MAXON...
FOR COMPREHENSIVE CONTROL OF YOUR M2M APPLICATION, THE ENVIROMAX IS A COMPLETE INTELLIGENT TELEMETRY PACKAGE TO ADVANCE & POWER YOUR INDUSTRIAL APPLICATION. Powered by the intelligence of Maxon’s exclusive Smartmax HSPA Smart Modem, the Enviromax controller is a cost-effective telemetry solution for M2M applications requiring supervisory and control of data equipment over the 3G network. Leveraging off the brains of the Smartmax Modem, the control flexibility of the Smartmax I/O Board, and it’s internal battery power, the Enviromax is impressively fully featured – including 6 digital inputs, 4 digital outputs, 2 analog inputs, 1 pulse input port, reporting using DNP3 or via SMS through programming of the digital inputs and outputs and much more. All this encased in a robust IP66 rated enclosure for challenging environmental conditions. Combine this enclosure with the solar panel option for your complete low cost RTU solution which can be easily interfaced with any M2M application without requiring any additional power supply or charging circuitry. Without requiring costly and time-consuming changes to your existing application setup, the Enviromax can be easily integrated. Ideally designed and developed for communications devices that require remote monitoring and control in M2M applications, the cost-effective Enviromax is an all-in-one smart telemetry solution.
Enviromax Features • Compatible with any wireless operator in Australia • HSPA, GSM, GPRS, EDGE compatible • 6 Digital Inputs • 4 Digital Outputs • 2 Analog Inputs • 1 Pulse Input • Supports DNP3 reporting • SMS reporting and Control • Configurable via Web Interface • Optional Solar Panel, Backup Battery and mounting brackets
210812
• SDK (Software Development Kit) is available for the Smartmax HSPA Modem (Product Code: MA-2010S)
M2M HSPA Smart Telemetry Solution: MA-3010S
Water
Product Code: MA-3010SC
Metering
Package includes:
Enviromax Enclosure Only
PACKAGE 2
Product Code: MA-3010SL
PACKAGE 1
Enviromax Product Options
Package includes:
Enviromax Enclosure + Solar Panel + Bracket & Arm
= =
+
Smartmax I/O Board
+
+
2x 12v 7AH Batteries
20w Solar Panel
+
+
IP66 Rated Enclosure
Mounting Bracket & Arm
Enviromax Optional/Additional Accessories:• Solar Panel, Smartmax Board, I/O Board, I/O Cable
Frequency Bands • WCDMA/HSPA 850MHz, 900MHz, 1900MHz, 2100MHz • GSM/GPRS/EDGE 850MHz, 900MHz, 1800MHz and 1900MHz
Road Signs
Smartmax HSPA Modem
General Specifications Smartmax I/O Board (MA-4020) 6 Digital Inputs Characteristics ·
VIH (Input voltage high range): 2 ~ 24V
Product Content Features:
·
VIL (Input voltage low range): -2 ~ 0.8V
·
Ri (Input impedance): more than 5 kΩ
• Mounting ARM and Bracket (galvanized)
·
Rd (Internal pull-up): 47 kΩ for short to ground detection
• IP 66 enclosure
·
Input chatters are filtered by S/W setting
• 20W solar panel
Security
• Smartmax interface board
1 Pulse at Input 0
• I/O board
·
Frequency range 0 ~ 1000 Hz
• 2 X 12V 7AH battery
·
Accuracy (25°C) 0.05 % of span
·
Temperature stability 0.005 % / °C
·
Input impedance 47kΩ
• Connection terminals
General Specifications -
Smartmax HSPA Modem (MA-2010) • Packet Data
Transport
• 2 Way SMS
MOSFET switch to ground
·
Ro (Output resistance): less than 300 m Ω
·
VOpen (maximum allowed output voltage on open): 24 VDC IOut (maximum allowed switching current to ground): 1A
·
Switching time < 10 msec
• Embedded TCP/IP, UDP/IP STACK
·
Chatter free
• In-built periodic reset
• Support VPN Server and Client Mode
·
2 Analog Inputs
• Dynamic DNS
·
12bit resolution
• Supports DNP3 (Outstation) using extension I/O board
·
Accuracy: Typical ±0.25% ; Worst Case ±1%
• In-Built Web Interface
·
Maximum sampling rate: 10 sample/sec
• Programmable scheduler to control WAN connection
·
Input signal type: one of 0~20mA, 0~5V, or 0~10V
• Telnet support • Save and restore modem configuration from a file • FOTA - Firmware upgrade over the air
www.maxon.com.au
·
·
• Remote SMS diagnostics & reset
Power
4 Digital Outputs
• External antenna connectivity to maximise HSPA coverage
· (The input type is selected by the jumper “PULSE” on the connected Smartmax and INPUT# on the I/O board) ·
Input impedance for the signal type 0 ~ 20mA < 100Ω
·
Input impedance for the signal type 0 ~ 10VDC > 10K Ω
A mini usb cable is required for first time purchasers of the Smartmax, as most of the programming can only be done via the web interface. This is available in the Smartmax Complete Package (MA-2010C), the Smartmax SDK (MA-7000), and separately. Speak to your Maxon Account Manager for more information.
T | +612 8707 3000 ● F | +612 8707 3001 ● E |
[email protected] ● 36A Gibson Avenue, Padstow NSW Australia 2211 ● www.maxon.com.au
