Transcript
RADIO EQ STACK
TUNERS / CASSETTE / DISC PLAYERS MINI
STAN
DIN
ISO DIN
SINGLE DBL DIN
CHASSIS H
13/4-2
2
2
2
3 7/ 8
3
CHASSIS W
1
7 /8
1
7 /8
1
7 /8
7
7 1/ 8
7 1/ 8
CHASSIS D
43/4-5 1/2
57/8-6 11/16
57/8-6 11/16
57/8-6 11/16
57/8-6 11/16
57/8-6 11/16
NOSE H
15/8-1 3/4
15/8-1 3/4
2 3/ 8
113/16
33/4-4
NOSE W
41/8-4 3/16
41/8-4 3/16
7 1/ 2
611/16
611/16-71/4
SHAFT SP.
1
3
UPDATED THROUGH 2002 2003 2004 2005
FORD 2001-UP EXPLORER 2 Door Sport Utility
1
5 /8-5 /4
5 /8-6
IN DASH APPLICATION NOTES K
KS
K
APPLICATION KIT MODEL:
K4
FRONT DOORS Factory Provisions: 4" Driver (in factory adapter) 11/4" Tweeter (in factory adapter) Aftermarket: 6 x 8", 61/2"KS, 51/4"KS KS=SA68
K4
FD1327B/FD1300/FD1300*
FD16/FDK9
HARNESS ADAPTOR:
KS
ANTENNA ADAPTOR:
IN-DASH INSTALLATION AREA DIMENSIONS MAX DEPTH
DEPTH 3
7 /4"
CAVITY DASH OPENING
WIDTH
3
7 /4"
10 /2"
43/8"
71/4"
4"
TYPE: FORD DOUBLE DIN
DASH MATERIAL:
PLASTIC
HEIGHT
1
1/8"
THICKNESS: REMOVE REAR SUPPORT MODIFY CAVITY
FOR MAX DEPTH
CAVITY
W
H
D
1
AMPLIFIER/EQ MOUNTING LOCATIONS UNDER/IN DASH
UNDER SEAT
GLOVE BOX 1
1
1
5 x 7 /2 x 2 /4" (Factory Adapter) 1 1 5 x 7 /2 x 1 /2" (Cut in Steel)
(WxHxD)
TRUNK/ CARGO 1
12 /2 x 3 /2 x 3 /2"
Various
Dimensions shown are inches. For inch/mm conversions refer to chart section.
NOTE: THIS MANUAL IS BASED ON CAREFULLY DOCUMENTED RESEARCH. ABSOLUTE ACCURACY IS ATTEMPTED BUT NOT GUARANTEED. USE THIS MANUAL AS A REFERENCE GUIDE. SCOSCHE, INC. CANNOT BE RESPONSIBLE FOR INCONSISTENCIES THAT MAY OCCUR.
*
For use in the mounting of either a single double ISO/DIN head unit or two ISO/ DIN head units. Minor dash modification required.
REAR SIDE PANELS - SPORT UTILITY Factory Provisions: Standard 6 x 8" (mounted in steel) Aftermarket: 6 x 8", 61/2"KS, 51/4"KS KS=SA68 xx1/2
Cavity
W
H
D
711/16 x 51/4 x 7" xx
DASH WITH FACTORY STEREO. B C1 C2 D D1 D2 D3 F1 F2 K K1 K2 K3 K4
= = = = = = = = = = = = = =
K5 = WHEN EQUIPPED WITH STANDARD TWO SHAFT RADIO/TAPE PLAYER. FABRICATE KIT WHEN EQUIPPED WITH FLAT FACE ELECTRONIC RADIO/TAPE PLAYER. KS = SCOSCHE KIT RECOMMENDED. N = NOT RECOMMENDED. EXTENSIVE MODIFICATION REQUIRED. P = PERFECT WITHOUT MODIFICATION. P1 = MODIFY OR REMOVE POCKETS. P2 = COIN POCKET LOCATION IN DASH (MAY REQUIRE TRIM KIT). P3 = PERFECT WHEN EQUIPPED WITH STANDARD TWO SHAFT RADIO, K WITHOUT. R = REAR LOAD ISOMOUNT. U = UNDERDASH. W1 = WITH POWER WINDOWS ONLY. W2 = WITHOUT POWER WINDOWS ONLY.
BACK UP PLATES REQUIRED. CUT TRIM/PLASTIC (STRUCTURE). CUT STEEL. BELOW DECK ONLY. LIFT PORTION OF DECK. (MAY REQUIRE STRUCTURAL REINFORCEMENT). CUT STEEL WHEN TOP MOUNTED. DO NOT IF BELOW DECK. NARROW SURFACE, BELOW DECK ONLY. MINIMUM MODIFICATION FILE SHAFT HOLES OR DASH OPENING. MODIFY DASH CAVITY AND/OR PANEL. INSTALLATION KIT, SPACER OR ADAPTOR REQUIRED. KIT MODIFICATIONS REQUIRED. EXTENSION KIT RECOMMENDED. WHEN EQUIPPED WITH FACTORY "ELECTRONIC" RADIO. FABRICATE PANEL/BRACKETS.
© 2000 SCOSCHE INDUSTRIES, INC. 87
ALL RIGHTS RESERVED FOR MORE INFORMATION VISIT www.scosche.com OR CALL SCOSCHE INDUSTRIES, INC. AT 800-363-4490
2001-UP FORD EXPLORER 2 DOOR SPORT UTILITY
DASH WITH FACTORY RADIO REMOVED.
PRELIMINARY:
FRONT DOOR PANEL.
DISCONNECT THE NEGATIVE BATTERY CABLE.
ANTENNA:
THE FACTORY ANTENNA IS LOCATED ON TOP OF PASSENGER’S SIDE FRONT FENDER.
RADIO REMOVAL AND IN-DASH INSTALLATION: NOTE: THE FACTORY RADIO PROVISION IS FOR A FORD DOUBLE DIN STYLE RADIO. WHEN INSTALLING AN AFTERMARKET HEAD UNIT, A DASH INSTALLATION KIT IS NEEDED. WE RECOMMEND THE SCOSCHE FD1327 OR FD1300 DASH INSTALLATION KIT FOR DIN MOUNT STEREOS AND THE SCOSCHE FD1330 FOR DOUBLE ISO/DIN MOUNT STEREOS. WHEN REMOVING THE STEREO, A SET OF FORD DIN REMOVAL TOOLS IS NEEDED. WE RECOMMEND THE SCOSCHE DT-1 FORD DIN REMOVAL TOOLS. 1. INSERT FORD DIN REMOVAL TOOLS TO RELEASE CLIPS, PULL RADIO OUT, DISCONNECT AND REMOVE.
FRONT DOOR SPEAKER INSTALLATION: NOTE: THE FACTORY SPEAKER PROVISION IS FOR A 4” DRIVER AND A 1 ¼” TWEETER MOUNTED IN A FACTORY SPEAKER ADAPTER. WHEN INSTALLING AN AFTERMARKET 5 ¼ OR 6 ½ SPEAKER, A SPEAKER ADAPTER IS REQUIRED. WE RECOMMEND THE SCOSCHE SA68 SPEAKER ADAPTER. 1. EXTRACT (2) PHILLIPS HEAD SCREWS FROM ARMREST. 2. EXTRACT (2) PHILLIPS HEAD SCREWS FROM BOTTOM EDGE OF DOOR PANEL. 3. USING A PANEL REMOVAL TOOL, UNSNAP PANEL FASTENERS AROUND PERIMETER OF DOOR PANEL, LIFT AWAY, DISCONNECT AND REMOVE. 4. EXTRACT (3) ¼” SCREWS SECURING SPEAKER, LIFT AWAY, DISCONNECT AND REMOVE.
FRONT DOOR FACTORY PROVISION IS FOR A 4" DRIVER AND A 1-1/4" TWEETER.
REAR SIDE PANEL SPEAKER INSTALLATION: NOTE: THE FACTORY SPEAKER PROVISION IS FOR A STANDARD 6 X 8” SPEAKER. WHEN INSTALLING AN AFTERMARKET 5 ¼ OR 6 ½ SPEAKER, A SPEAKER ADAPTER IS REQUIRED. WE RECOMMEND THE SCOSCHE SA68 SPEAKER ADAPTER. 1. USING A PANEL REMOVAL TOOL, CAREFULLY PRESS DOWN ON TOP OF SPEAKER GRILL TO RELEASE, LIFT AWAY AND REMOVE. 2. EXTRACT (4) 7/32” SCREWS SECURING SPEAKER, LIFT AWAY, DISCONNECT AND REMOVE.
REAR SIDE PANEL SPEAKER SLOCATION.
© 2000 SCOSCHE INDUSTRIES, INC. 88
ALL RIGHTS RESERVED FOR MORE INFORMATION VISIT www.scosche.com OR CALL SCOSCHE INDUSTRIES, INC. AT 800-363-4490
