Transcript
NT: ompletned RTAfor the cio O ns, a P m IM n.co truct the
g ins tro w.ex tallation onnectin . e c o ww s Go t uide, in s before er sourc g w n user cificatio o the po spe roduct t p
FOX II T HD 4K • Setup Guide This guide provides quick start instructions for an experienced installer to set up and operate the Extron FOX II T HD 4K Fiber Optic Transmitter. The transmitter is compatible with all Extron FOX II receivers.
WARNING: The FOX II T HD 4K outputs continuous invisible light (Class 1 rated), which may be harmful to the eyes; use with caution. Plug the attached dust caps into the optical transceivers when the fiber cable is unplugged.
CLASS 1 LASER PRODUCT, see the FOX II T HD 4K User Guide, at www.extron.com.
AVERTISSEMENT :
Le FOX II T HD 4K émet une lumière invisible en continu (conforme à la classe 1) qui peut être dangereux pour les yeux, à utiliser avec précaution. Branchez les protections contre la poussière dans l’ensemble émetteur/récepteur lorsque le câble fibre optique est débranché.
Produit laser de classe 1, voir le FOX II T HD 4K User Guide sur www.extron.com (en anglais).
Installation
Step 2 — Input and Output Connections a.
RS-232
AUDIO RETURN OUT
AUDIO L
50-60 Hz
HDMI
R
L
RS-232
LOOP THRU
ALARM
Tx Rx G 1
2
T HD 4K
Rx RESET
OPTICAL
FOX II T HD 4K Transmitter Rear Panel
Connect an HDMI video source to the HDMI input connector. HDMI
b. If desired, connect an HDMI video display to the Loop-Thru connector for a local display. c.
Tx
REMOTE
R
FOX
LINK
INPUTS
IR
Tx Rx G Tx Rx
OVER FIBER
Turn off or disconnect all equipment power sources and mount the transmitter as required. For mounting details and considerations, see the FOX II T HD 4K User Guide at www.extron.com.
100-240V ~ 0.5A MAX
LINK
Step 1 — Mounting
LOOP THRU
Connect an audio input device to either the Audio 3.5 mm mini jack or the Audio 5-pole captive screw connector. See the drawing below step 2d to make connections on the captive screw connector.
AUDIO L
d. For optional returned audio, connect an audio output device to the Audio Return Out 5-pole captive screw connector.
See the drawing below to make connections on the captive screw connector.
R
R
Balanced Stereo Input
Unbalanced Stereo Input No Ground Here
Tip Ring Sleeves Tip Ring
R
No Ground Here
Unbalanced Stereo Output
L
R
Tip Sleeves Tip
L
• Pour l’audio asymétrique, connectez les manchons au contact au sol. Ne PAS connecter les manchons aux contacts négatifs (–).
Tip Ring Sleeves Tip Ring
L
• For unbalanced audio, connect the sleeves to the ground contact. DO NOT connect the sleeves to the negative (–) contacts.
AUDIO RETURN OUT L
R
Tip Sleeve Tip Sleeve
L
ATTENTION:
R
Balanced Stereo Output
Do not tin the wires!
NOTE: For returned audio, above, you must also do the following: • Connect an audio input device to the Audio Return In 5-pole captive screw connector on the receiver. • Install the optional Receiver-Tx-to-transmitter-Rx cable in step 3b. e.
RS-232 Device Gnd Rx Tx
Gnd Tx Rx
IR
NOTE: For returned RS-232 and IR responses (from the receiver to the transmitter, you must install the Receiver-Tx-to-transmitter-Rx cable in step 3b.
RS-232
Tx Rx G Tx Rx
If you want the FOX II units to pass serial or IR data or control signals, such as for serial control of a projector, connect the master device to the transmitter and the slave device to the receiver via the Over Fiber 5-pole captive screw connector.
OVER FIBER
IR Device
1
FOX II T HD 4K • Setup Guide (Continued) f.
For remote monitoring of the status of the Rx optical link, connect a locally constructed or obtained device to the two rightmost Alarm poles of the Alarm and Remote RS-232 5-pole captive screw connector. The unit shorts both poles together when no light is detected.
REMOTE RS-232
ALARM
Tx Rx G 1
2
NOTE: The transmitter Alarm port reports the status of the link from the receiver. g.
For remote control of a unit and loading firmware, connect a host device, such as a computer or control system, to either of the following ports: Configuration port — The front panel mini USB connector.
CONFIG
NOTE: Extron recommends performing firmware updates via the Configuration port only. Remote RS-232 port — The rear panel Remote RS-232 port, the 3 leftmost poles of this 5-pole captive screw connector. The protocol for the Remote port is as follows: • •
no parity no flow control
•
8 data bits
Step 3 — Throughput Connections NOTE: See the two fiber cable connection drawing at right. You can connect the transmitter to a compatible receiver in one of two ways: • One way (transmitter to receiver) only, perform step 3a.
ALARM
Tx Rx G 1
Tx
2
Rx LINK
9600 baud 1 stop bit
RS-232
LINK
• •
REMOTE
OPTICAL
Transmitter
1
2
• Two way (transmitter to receiver and return), perform steps 3a and 3b. a.
Connect the fiber between the Tx port on the transmitter and the Rx port on the receiver (1, at right).
b. If you want the receiver to return serial data (such as responses from a controlled device) to the transmitter, connect
a cable between the Tx port on the receiver and Rx port on the transmitter (2).
1 Tx
Rx LINK
NOTE: The Link LEDs indicate transmission of light only, not whether there is data encoded in the optical link.
2 LINK
Tx Link and Rx Link LEDs — When lit, the link is active (light is output [Tx] or received [Rx]).
Receiver OPTICAL
2
Operation After the receiver, the transmitter, and their connected devices are powered up, the system is fully operational. If any problems are encountered, verify that the cables are routed and connected properly and that the display device has a compatible resolution and refresh rate. If problems persist, call the Extron S3 Sales & Technical Support Hotline. See the contact numbers on the last page of this guide for the Extron office nearest you.
Indications Power LED — Indicates that power is applied to the unit. Video LEDs —
VIDEO
Signal LED — Lights when the unit detects an input video signal.
CONFIG
HDCP LED — Lights when the input signal is HDCP encrypted.
AUDIO
SIGNAL
INPUT
HDCP
RETURN OUT
EDID SELECT
Audio LEDs — Input LED — Lights when an analog audio or PCM digital audio signal remains above -35 dBV. The LED goes unlit if the audio signal level drops below the threshold for 10 seconds or longer. Return Out LED — Lights when analog audio is present on the transmitter Return Audio Output connector.
EDID EDID Select rotary switch — Set this switch to one of the positions shown in the table below to select the source of the DDC or a specific resolution. Position 0 — An EDID that has previously been captured from a connected display or manually imported via an SIS command or the Product Configuration Software. Position 1 — The EDID is selected via the remote or USB port on the transmitter only, using an SIS command or the Extron Product Configuration Software. Position 2 — Use the EDID from the display connected to the receiver. NOTE: EDID from the display connected to the receiver requires connection of both fiber cables. Position 3 — Use the EDID from the display connected to the transmitter loop-through. Positions 4 through E — Specify a resolution. The table at right identifies the resolutions associated with the switch positions. All resolutions are at 60 Hz with the exception of 4096x2160 (E), which is 30 Hz. Position F — No EDID assigned.
Pos. Source or resolution 0 User recorded EDID 1 Selected via RS-232 2 Display on Rx output 3 Display on Tx loop-through 4 1280x720 5 1280x800 * 30 Hz
Pos. 6 7 8 9 A B
Resolution 1366x768 1440x900 1680x1050 1920x1080 1920x1200 2048x1536
Pos. C D E* F
Resolution 2048x2160 2560x1600 4096x2160 N/A
3
FOX II T HD 4K • Setup Guide (Continued) Application Diagram Extron FOX T HD 4K
Fiber Optic Transmitter Extron IPCP Pro 250
IP Link Pro Control Processor IPC
P PR
O
25
0
Ethernet
L I/O
DIG M
D
X
TH
M
L
DIO
PU
TS
AU L
G
AR
Tx
Rx
G
1
Tx
M
AL
R
Rx
G
Tx RTS
CTS
V
C
4
3
2
G
AYS REL C 1
VOL
Rx
eBU +V
+S
G
IR/S
S
-S
2
LAN
G S =
G
6W
OUT
G
PWR
ET
RES
TCP/IP Network
Rx
Tx
E
LINK
Rx
T MO RE 232 S-
LINK
OVER FIBER
RS
Tx
DIO UT AURN O TU RE R
Tx
ER POW X 12V MA --A
Rx
1
1
CO
FO
IR -232
ITA
2
CO
4K
AL
TIC
OP
2
RS-232
R
Ethernet
240V 100-
5A ~ 0.
OP
r ne
Audio
RU TH
LO
e
lum
4
ts te
Mu
HDMI Downscaled to 1080p
st
La
9 er
Ent
0 ber em Dec p
Hel
re Mosets Pre
dio Auntrol Co
tem Sys Off
8 7
n
ree
Sc
15,
201
3-
8 AM 7:5
E ttrxon nEoxr
ng hti Lig
Extron TLP Pro 720T
7" Table Top TouchLink Pro Touchpanel
Up to 30 km (18.75 miles) Singlemode Fiber SM Model
S
TU STA Y PLA R
WE PO
US
6 5
om Ro ol ntr Co
Local Monitor
CA
1
te Mu
4K HDMI
SD
2
y
On Off
Hz
se
3 pla
Dis
MI
50
an
Ch
Tu
op
Pre
l
ne
Lapt
HD
-60
3
Vo
VCR DVD PC
MAX
12
r
Tune Doc Cam
IN
B
RD
Extron XPA 1002 02 A 10 XP S2
G T RIN TPU 2 WI OU
AS
CL
1
Power Amplifier
TE
MO
RE
4K Media Player
UTS
mA 50 TE /MU 10V VOL
INP
2 1 EL
LEV
STA
Y NDB
2
1 1
0Hz , 50-6
1.3A 240V
R/ ITE T LIM EC OT PR NAL SIG
0
2
0
100-
P 4K
RD
X
L
S DIO UT TP AU
OU
Extron FOX R DP 4K
Fiber Optic Receiver
240V 100-
AX AM ~ -.-
-60
50
Hz
YP LA
R
L
Rx
G
T MO RE 232 SRx
G
M
AR
AL
1
RES
ET
Rx
Tx
E
R
Tx
Tx
Rx
LINK
Tx
DIO IN AU RN TU RE R
LINK
OVER FIBER
FO
IR -232 RS
AL
TIC
OP
2
Audio
T OR
P DIS
RS-232
4K DisplayPort
L 80
MO
DE
Extron SI 28
Surface-mount Speakers
Extron Headquarters +800.633.9876 Inside USA/Canada Only Extron USA - West Extron USA - East +1.714.491.1500 +1.919.850.1000 +1.714.491.1517 FAX +1.919.850.1001 FAX
4
Extron Europe +800.3987.6673 Inside Europe Only +31.33.453.4040 +31.33.453.4050 FAX
Extron Asia +65.6383.4400 +65.6383.4664 FAX
Extron Japan +81.3.3511.7655 +81.3.3511.7656 FAX
Extron China +86.21.3760.1568 +86.21.3760.1566 FAX
4K Display
Extron Middle East +971.4.299.1800 +971.4.299.1880 FAX
Extron Korea +82.2.3444.1571 +82.2.3444.1575 FAX
Extron India 1800.3070.3777 (Inside India Only) +91.80.3055.3777 +91.80.3055.3737 FAX
© 2015 Extron Electronics All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com
68-2300-50 Rev. Ax 04 15
