Transcript
NT: ompletned RTAfor the cio O ns, a P m IM n.co truct the
g ins tro w.ex tallation onnectin . e c o ww s Go t uide, in s before er sourc g w n user cificatio o the po spe roduct t p
FOX II T/R DP 4K • Setup Guide This guide provides quick start instructions for an experienced installer to set up and operate the Extron FOX II T/R DP 4K Fiber Optic Extenders.
WARNING: The FOX II T/R DP 4K outputs continuous invisible light (Class 1 rated), which may be harmful to the eyes; use with caution. Plug the attached dust caps into the optical transceivers when the fiber cable is unplugged. CLASS 1 LASER PRODUCT, see the FOX II T/R DP 4K User Guide, at www.extron.com.
AVERTISSEMENT :
Le FOX II T/R DP 4K émet une lumière invisible en continu (conforme à la classe 1) qui peut être dangereux pour les yeux, à utiliser avec précaution. Branchez les protections contre la poussière dans l’ensemble émetteur/récepteur lorsque le câble fibre optique est débranché.
Produit laser de classe 1, voir le FOX II T/R DP 4K User Guide sur www.extron.com (en anglais).
L
50-60 Hz
DISPLAYPORT
R
L
Tx Rx G Tx Rx
R
RS-232
LOOP THRU
b. If desired, connect a DisplayPort video display
T DP 4K
Rx
2
RESET
OPTICAL
FOX II DP 4K Transmitter Rear Panel RS-232
OUTPUTS AUDIO L
50-60 Hz
AUDIO RETURN IN R
L
IR
Tx Rx G Tx Rx
Tx
REMOTE
R
RS-232
DISPLAYPORT
FOX
ALARM
Tx Rx G 1
R DP 4K
Rx LINK
Step 2 — Input and Output Connections Connect a DisplayPort DISPLAYPORT LOOP THRU video source to the transmitter DisplayPort input connector.
ALARM
Tx Rx G 1
100-240V ~ -.-A MAX
a.
Tx
REMOTE
OVER FIBER
Turn off or disconnect all equipment power sources and mount the transmitter and receiver as required. For mounting details and considerations, see the FOX II T/R DP 4K User Guide at www.extron.com.
AUDIO RETURN OUT
AUDIO
FOX
LINK
INPUTS
Step 1 — Mounting
IR
OVER FIBER
RS-232
LINK
100-240V ~ -.-A MAX
LINK
Installation
2
RESET
OPTICAL
FOX II DP 4K Receiver Rear Panel
to the transmitter Loop-Thru connector for a local display. c.
Connect a DisplayPort video display to the receiver DisplayPort output connector.
DISPLAYPORT
d. Connect an audio input device to either the Audio 3.5 mm mini jack or the Audio 5-pole captive screw connector
AUDIO L
on the transmitter. See the drawing below step 2g to make connections on the captive screw connector. e.
Connect an audio output device to either or both the 3.5 mm mini jack or the Audio 5-pole captive screw connector on the receiver. See the drawing below step 2g to make connections on the captive screw connector.
f.
For optional returned audio, connect an audio output device to the Audio Return Out 5-pole captive screw connector on the transmitter. See the drawing below step 2g to make connections on the captive screw connector.
g.
AUDIO RETURN OUT L
R
R
AUDIO RETURN IN L
R
For optional returned audio, connect an audio input device to the Audio Return In 5-pole captive screw connector on the receiver. See the drawing below to make connections on the captive screw connector. L
Tip Ring Sleeves Tip Ring
R
Balanced Stereo Input
Unbalanced Stereo Input No Ground Here
R
Unbalanced Stereo Output
Tip Ring Sleeves Tip Ring
L
No Ground Here
R
Do not tin the wires!
Tip Sleeves Tip
L
• Pour l’audio asymétrique, connectez les manchons au contact au sol. Ne PAS connecter les manchons aux contacts négatifs (–).
R
Tip Sleeve Tip Sleeve
• For unbalanced audio, connect the sleeves to the ground contact. DO NOT connect the sleeves to the negative (–) contacts.
L
ATTENTION:
Balanced Stereo Output
NOTE: For returned audio, above, and RS-232 and IR responses (from the receiver to the transmitter), on the next page, you must install the receiver-Tx-to-transmitter-Rx cable in step 3b.
1
FOX II T/R DP 4K • Setup Guide (Continued) h. If you want the FOX II DP 4K units to pass serial or IR data or control signals, such as for serial
RS-232 Device Gnd Rx Tx
REMOTE RS-232
ALARM
Tx Rx G 1
2
IR
For remote monitoring of the status of the Rx optical link on either the transmitter or receiver, connect a locally constructed or obtained device to the two rightmost poles of the Alarm and Remote RS-232 5-pole captive screw connector on that unit. The unit shorts both poles together when no light is detected.
RS-232
i.
Tx Rx G Tx Rx
control of a projector, connect the master device to the transmitter and the controlled device to the receiver via the Over Fiber 5-pole captive screw connectors on both units.
OVER FIBER
Gnd Tx Rx
IR Device
NOTE: The transmitter port reports the status of the link from the receiver. The receiver port reports the status of the link from the transmitter. j.
For remote control of a unit and for loading firmware, connect a host device, such as a computer or control system, to either of the following ports on the unit to be controlled: Configuration port — The front panel USB mini-B connector.
CONFIG
NOTE: Extron recommends performing firmware updates via the Configuration port only. Remote RS-232 port — The rear panel Remote RS-232 port, the 3 leftmost poles of this 5-pole captive screw connector. The protocol for the Remote port is as follows: • •
no parity no flow control
•
8 data bits
Step 3 — Throughput Connections NOTE: See the two fiber cable connection drawing at right. You can connect the transmitter and receiver in one of two ways: • One way (transmitter to receiver) only, perform step 3a.
ALARM
Tx Rx G 1
Tx
2
Rx LINK
9600 baud 1 stop bit
RS-232
LINK
• •
REMOTE
OPTICAL
Transmitter
1
2
• Two way (transmitter to receiver and return), perform steps 3a and 3b. Connect the fiber between the Tx port on the transmitter and the Rx port on the receiver (1, at right).
b. If you want the receiver to return serial data (such as responses from a controlled device), IR data, or returned audio
to the transmitter, connect a cable between the Tx port on the receiver and Rx port on the transmitter (2). Tx Link and Rx Link LEDs — When lit, the link is active (light is output [Tx] or received [Rx]). NOTE: The Link LEDs indicate transmission of light only, not whether there is data encoded in the optical link.
2
2
1 Tx
Rx LINK
NOTE: Ensure that the transmitter and connected receiver are the same transmission mode, singlemode (SM) or multimode (MM) and that you use the correct SM or MM fiber cable to connect the devices.
LINK
a.
Receiver OPTICAL
Operation After the receiver, the transmitter, and their connected devices are powered up, the system is fully operational. If any problems are encountered, verify that the cables are routed and connected properly and that the display device has a compatible resolution and refresh rate. If problems persist, call the Extron S3 Sales & Technical Support Hotline. See the contact numbers on the last page of this guide for the Extron office nearest you.
Indications NOTE: The figure below right is of a receiver. A transmitter has similar indications. Power (
) LED — Indicates that power is applied to the unit.
Video LEDs — Signal LED — Lights on both units when the unit detects an input video signal.
VIDEO CONFIG
HDCP LED — Lights on both units when the input signal is HDCP encrypted.
AUDIO
SIGNAL
OUTPUT
HDCP
RETURN IN
Audio LEDs — Input LED (transmitter) — Lights when an analog audio or PCM digital audio signal remains above -35 dBV. The LED goes unlit if the audio signal level drops below the threshold for 10 seconds or longer. Output LED (receiver) — Lights when an analog audio or PCM digital audio signal remains above -35 dBV. The LED goes unlit if the audio signal level drops below the threshold for 10 seconds or longer. Return Out LED (transmitter) — Lights when analog audio is present on the transmitter Return Audio Output connector. Return In LED (receiver) — Lights when analog audio is present on the receiver Return Audio Input connector.
EDID (Transmitter)
EDID SELECT
EDID Select rotary switch — Set this switch to one of the positions shown in the table below to select the source of the EDID or a specific resolution. Position 0 — An EDID that has previously been captured from a connected display or manually imported via an SIS command or the Product Configuration Software. Position 1 — The EDID is selected via the Remote or USB port on the transmitter only, using an SIS command or the Extron Product Configuration Software. Position 2 — Use the EDID from the display connected to the receiver. NOTE: EDID from the display connected to the receiver requires connection of both fiber cables. Position 3 — Use the EDID from the display connected to the transmitter loop-through. Positions 4 through E — Specify a resolution. The table at right identifies the resolutions associated with the switch positions. All resolutions are at 60 Hz with the exception of 3840x2160 (E), which is 30 Hz. Position F — No EDID assigned.
Pos. Source or resolution 0 User recorded EDID 1 Selected via RS-232 2 Display on Rx output 3 Display on Tx loop-through 4 1280x720 5 1280x800 * 30 Hz
Pos. 6 7 8 9 A B
Resolution 1366x768 1440x900 1680x1050 1920x1080 1920x1200 2048x1536
Pos. C D E* F
Resolution 2048x2160 2560x1600 3840x2160 N/A
Remote control See the FOX II T/R DP 4K User Guide, available at www.extron.com, for details on operating and monitoring the transmitter and receiver using either SIS commands or the Extron Product Configuration Software.
3
FOX II T/R DP 4K • Setup Guide (Continued) Application Diagram Extron FOX T DP 4K
Fiber Optic Transmitter Extron IPCP Pro 250
IP Link Pro Control Processor IPC
P PR
O
25
0
Ethernet
L I/O
DIG M
ITA
2
CO
X
T
M
4K DP Tx
RS
L
DIO
TS
AU L
Rx
G
T MO RE 232 S-
Tx
Rx
G
Tx
M
AR
AL
R
1
Rx
G
RTS
CTS
C
Rx
2
C
4
3
2
G
AYS
REL 1
VOL V
ER POW X 12V MA --A
Tx
eBU +V
+S
G
IR/S
S
-S
LAN
G S =
G
6W
OUT
G
PWR
ET
RES
TCP/IP Network
Rx
Tx
E
LINK
Tx
DIO UT AURN O TU RE R
Rx
LINK
OVER FIBER
FO
IR -232
1
1
CO
AL
TIC
OP
2
RS-232
R
Ethernet
AX AM ~ -.-
OP
e
lum
ts
se
Audio
RU
TH
LO
r
Ch
Pre
l
ne
an
ne
Tu
op Lapt
te
Mu
3 pla
2
y
1
Dis
T OR
YP PLA
6 5
On
4
Off
DIS
9
ber em Dec p
Hel
re Mosets Pre
dio Auntrol Co
tem Sys Off er
Ent
0
n
ree
Sc
Hz
st
La
8 7
te Mu
om Ro ol ntr Co
-60
3
Vo
VCR DVD PC
240V 100-
12
r
Tune Doc Cam
PU
IN
15,
201
3-
8 AM 7:5
E ttrxon nEoxr
ng hti Lig
50
Extron TLP Pro 720T
4K DisplayPort 4K DisplayPort
7" Table Top TouchLink Pro Touchpanel
Up to 30 km (18.75 miles) Singlemode Fiber SM Model
Local Monitor
Extron XPA 1002
PC
02 A 10 XP S2
G T RIN TPU 2 WI OU
AS
CL
1
Power Amplifier
TE
MO
RE
UTS
mA 50 TE /MU 10V VOL
INP
2 1 EL
LEV
STA
Y NDB
2
1 1
0Hz , 50-6
1.3A 240V
R/ ITE T LIM EC OT PR NAL SIG
0
2
0
100-
P 4K
RD
X
L
S DIO UT TP AU
OU
Extron FOX R DP 4K
Fiber Optic Receiver
240V 100-
AX AM ~ -.-
-60
50
Hz
R
L
Rx
G
M
AR
AL
R
Tx
Rx
G
Tx
1
RES
ET
Rx
Tx
E
T MO RE 232 S-
Rx
LINK
Tx
DIO IN AU RN TU RE R
LINK
OVER FIBER
FO
IR -232 RS
AL
TIC
OP
2
Audio
T OR
YP LA
P DIS
RS-232
4K DisplayPort
MO
DE
L 80
Extron SI 28
Surface-mount Speakers
Extron Headquarters +800.633.9876 Inside USA/Canada Only Extron USA - West Extron USA - East +1.714.491.1500 +1.919.850.1000 +1.714.491.1517 FAX +1.919.850.1001 FAX
4
Extron Europe +800.3987.6673 Inside Europe Only +31.33.453.4040 +31.33.453.4050 FAX
Extron Asia +65.6383.4400 +65.6383.4664 FAX
Extron Japan +81.3.3511.7655 +81.3.3511.7656 FAX
Extron China +86.21.3760.1568 +86.21.3760.1566 FAX
4K Display
Extron Middle East +971.4.299.1800 +971.4.299.1880 FAX
Extron Korea +82.2.3444.1571 +82.2.3444.1575 FAX
Extron India 1800.3070.3777 (Inside India Only) +91.80.3055.3777 +91.80.3055.3737 FAX
© 2016 Extron Electronics All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com
68-2540-50 Rev. B 01 16
