Transcript
FP8151 Series User’s Quick Reference
Version 1.0 1. Brief
Page 1/3
4. Features
The FP8151x is an 15-inch Panel PC with touch screen device (FP8151xT). This user’s quick reference provides its outlook information and I/O outlets description.
* *
2. Dimensions (in mm) and Rear I/O Information
*
* *
Cut out dimension 351.2 x 262.6mm Note: 1. FP8151 + PANEL MOUNTING KIT
Processor Board Intel low power Celeron-M processor with 1GB DDR2 RAM. (2GB Max.) I/O Outlets One 10/100/1000 base-TX Ethernet port. 4 USB ports (V2.0) and 1 RS-232/485 serial port. 1 VGA (CRT) and 1 PS/2 compatible keyboard/mouse interface. 2 Audio connectors for Earphone and Microphone. 1 mini-PCI socket for mini-PCI I/O modules, especially for WLAN modules. 1 DC-In plug connector and 1 terminal block for DC power input. 1 power button and 1 reset button. Storage Bay 1 CompactFlash socket for CompactFlash modules or MicroDrives. One 2.5" SATA hard disk space. Power requirement +12 ~ +24V DC, 2.64A maximum (1.96A typical) with 19V input voltage. Mechanical Dimensions: 401.0mm(W) x 308.0mm(H) x 63.5mm (D) (w/o wall mount kit) Weight: 7.24Kg.(Standard packing) Approval: IP65 Compliant.
5. I/O outlets and LED Indicator A. Power Connectors DC12~24V
DC12~24V
/
DC Plug-In Connector Terminal Block DC +12V to +24V, 63W minimum
USB
MIC
LINE GIGALAN KB/MOUSE COM OUT
CRT
RESET DC IN 12V~24V DC IN 12V~24V POWER
B. VGA, Serial port, Keyboard/Mouse, LAN, Audio, and USB Connectors
3. Packing List 1 FP8151x/FP8151xT industrial Panel PC. 1 65W AC to DC19V power adapter and 1 AC power code cable. 1 Y-type (3-end) PS/2 keyboard plus mouse port adapter cable. 1 pack of embedded mounting kit with 4 screws. 1 pack of 2.5” SATA HDD installing kit with 4 screws. 1 touch pen for touch screen (Optional for FP8151T only) 1 Compact Disc including user’s manual and touch screen drivers.
www.fabiatech.com
USB #1, #2
Mic-In Earphone (Line-Out)
USB #3, #4 On the down side of FP8151x
LAN
Keyboard (& Mouse)
COM1
VGA (D-sub 15)
Note 1: Standard PS/2 keyboard can be plugged into this connector without any adapter cable. If PS/2 keyboard and mouse will be used simultaneously, an optional Y-type adapter cable is needed. Note 2: The LAN port is a RJ45 connector with 2 LEDs. The orange LED indicates data is accessing and the green LED indicates on-line status. (When lighted indicates on-line and off indicates off-line)
©2009 FabiaTech Corporation
FP8151 Series User’s Quick Reference
Version 1.0 6. Installation
Page 2/3
C. Installing DDR2 Modules, mini PCI WLAN Modules, and Antenna
A. Installing CompactFlash Modules
2 4 1
3 6 1
2
5
Step 1: Open the CF cover (2 screws)
Step 2: Insert CF and close cover Step 1: Open the back cover as previous section shown and then release 6 screws for main board separation.
B. Installing 2.5” SATA Hard Disks
Step 2: Separate the main board from panel carefully and reverse it and put aside.
13 3
4
5 6
2 7
Step 2: Insert 2.5” SATA HDD with included HDD kit (4 screws) 8
1 11
10
1
2
9
12
Step 3: Install/Change the DDR2 modules
Step 4: Install WLAN module and antenna cable
Step 5: Install antenna cable with back cover
Step 6: Close back cover and install antenna
3 4
Step 1: Open the back cover (13 screws)
1
3
2
4
Step 3: Install HDD kit to FP8151x (4 screws)
www.fabiatech.com
Step 4: Connect SATA cable to HDD
©2009 FabiaTech Corporation
Version 1.0
FP8151 Series User’s Quick Reference
Page 3/3
D. Wall Mounting and Mounting Dimensions
Mounting Option 1: VESA 75/100mm standard for monitor stand (optional)
Wall mounting holes (2 holes, pitch 74mm)
End of Document
www.fabiatech.com
©2009 FabiaTech Corporation
