Transcript
Free-Standing Bathtub Installation Instructions
Contents: Product drawing ....................................1 Jacuzzi installation instructions................2 Cleaning and maintenance tips................3 Caution....................................................4
1.Product Drawing
2.Jacuzzi installation instructions (1)The need to prepare material 1. Source: Stainless steel tube each a root, from the ground level 300 mm, the wall with globe valve 2. Power: AC120V/frequency 60 Hz, single phase three wire, BV = 3, from the ground level 400 mm, with 10 A waterproof socket 3. From ground level in 130 mm or so, the product with the power control switch. 4. Drainage: buccal should be a drain on here as the center, the radius of the 200 mm range (don't in the center), and hose connection (2) The installation process This product components adopt standard part, when installation, please refer to the product technical parameters, according to the following steps to installation: 1. Determine product installation position: please refer to the water and electricity parameter table and hydropower installation figure decorate water pipe, power outlets, pipes, etc. And to ensure enough position connection. Then will bath crock as for installation place, adjust the bottom to keep balance nut cylinder level. In order to the next step of convenient installation, the first move out of a bath crock, to install complete to move back to install a. 2. Connections sewer: drain in bath crock bottom, is 1 throat section plastic pipe, can be arbitrary Angle bending, connection will be fixed in the sewers please end, then use adhesive tape or glass seal. Note can't discount, so as not to affect the drainage 3. Connect feed line: feed line for heat resistant to high temperature high pressure pipe net silk, please click joints connected cold 'hot water mark joint, do not take the, in order to maintain convenient, the proposal within the cold and hot water to install a valve 4. Connect the power: this product is suitable for 120 v ac power, please according to the installation drawing with electricity and water leakage switch and socket position, note waterproof. Insert the plug into the power supply socket, press the reset button leakage protection plugs, the indicator light can. Pay attention to ensure good bath crock grounding. 5. Check the cleaning: the above steps after completion, check the pipe joints is sealed, make sure clear after the cylinder is sundry, open the drainage device, water to clean bath crock (be sure to clean in order to avoid damage the pump).
6. Adding water test: confirmation without sundries in cylinder closed after drainage, then water storage, electric test
3. Cleaning and maintenance tips 1.The cleanness of massage bath. (1)Daily cleaning massage bath use liquid detergent and soft cloth. Not clean with det ergent containing contain ketone or chlorine water composition; During disinfection, disable use disinfectant containing formic acid and formaldehyde. (2)Suggest use granular detergent can be mixed with water to clean the massage bath , avoid to use for ceramic tile or enamel surface cleanser. (3)Do not leave the containers of liquid detergent on bathtub surface for a long time, d o not use the spray or thickening agent or other similar cleaning supplies. (4)Please do not let the nail polish, nail polish remover, dry liquid detergent, acetone, paint remover or other solvent get to Acrylic surface.
(5)Corrosive cleaner will damage Acrylic’s surface, pay attention to clean bath surfac e after each use, don't let the cleaner into the circulatory system. 2.The maintenance of the massage bath (1)if the bath surface has scratches, burnish with 2000 waterproofabrasive paper, appl y with toothpaste , with a soft cloth polishingcan make it bright and clean like new ag ain. (2)The surface of the bath with Scale can use detergent containing light acidic , such a s lemon juice, vinegar with soft cloth to wipe after slight fever. (3)Cleaning the Hydraulic friction device when the bath filled with 40 degrees celsius hot water, per liter add 2 grams cleaner, start the hydraulic massage for about 5 minutes, stop the pump drainage, and then fill it with cold water, start the hydraulic massage for 3 minutes, stop the pump drainage and clean bath.
(4)Use wet towel to wipe Cylinder block surface dirt, this process can be repeated thre e times, make it bright and clean like new. (5)Do not use rough surface cleaning equipment, don’t use detergents containing che mical solvent or particles clean bath surface.
(6)Do not use hard objects, blade struck score bathtub surface, also should not let ciga rette or Pyrogen higher than 70 degree centigrade get in the bath surface. (7)After using, should be no water and power off. (8)Backwater and the nozzle blocked by hair or other sundry , unscrewed and clean. (9)Gold Plating, chrome plating, do not need to wipe often.
4.Caution 1.No matter whether to use massage equipment, in order to ensure the normal operatio n of equipment the water inlet of the massage bath should no cover or blockage. 2.Because the massage bath massage can lead to accelerated blood flow to the human body, people has the heart cerebrovascular disease such as heart disease and blood cl ots should be careful to use, and the water temperature can not too high, the man with leg varicose veins should ask doctor's advice and opinion. 3.Best bath time is after 9 o 'clock in the evening, before going to bed so can let a pers on's mental and physical very flabby, it much better massage time not exceed 30 minu tes each time, the water temperature does not exceed 38 ° C, don't start up after bath, t o avoid dizziness accidents.
