Front Panel Rear Panel Power On/off Status Indicator Lamp:the

Transcript

7) Copy EDID function Copy the EDID of the sink which connected the OUTPUT1,it is suggested to put lowest or the most compatible display specification on output1. For example: One SDTV(480p) ,one HDTV(1080p), in order to make the 2 TV work, you need to put the SDTV is connected to the output 1 . Front Panel 1 Power ON/OFF 2 Reset key 3 Status indicator lamp:The LED will illuminate when the HDMI equipment is connected. 4 Power indicator lamp:The LED will illuminate when the power is on. Rear Panel RS-232 pin assignment HDBaseT Splitter 1 Output1 port ( RS232&IR pass-though) 3 HDMI input port 2 Output2 port ( IR pass-though) 4 Power input port 5 RS232 port HDMI cable Connecting and operating 1) Connect the HDMI input sources into HDBaseT splitter. 2) Connect HDMI receiver over Cat5e/Cat6 cables to both the Cat5e/6 port of HDBaseT Splitter and Cat5e/6 port of Receiver,The RJ45 connections must follow EIA-TIA 568b standards. 3) Connect the HDMI output from the Receiver(RX) into the display HDMI input. 4) Connect the IR TX receiving cables into splitter IR TX port on the back panel and affix the emitter onto the source IR windows. . 5) Connect IR-RX cable into IR-RX port on the receiver and affix the IR receiver in direct line of site with the handheld remote control.It is recommended to affix the receiver on the display frame /bezel or the display stand. Note：Do not affix the emitter until the placement is tested. 6) Power up all units, the splitter,Receiver, sources and displays. RS232 cable HDTV HDMI cable HDMI cable Output1 HDTV Computer RS232 port PIN Assignment PIN Assignment 1 NC 1 NC 2 TX 2 RX 3 RX 3 TX 4 NC 4 NC 5 GND 5 GND 6 NC 6 NC 7 NC 7 NC 8 NC 8 NC 9 NC 9 NC Quick Start Guide 2-PORT HDBaseT SPLITTER Features •Incorporates HD Base-T technology •Distributes 1 HDMI source to 2 HDMI Displays simultaneously. •Full HD support: 1080p@60Hz@48 b/pixels, support 3D and 4Kx2K •Extends HDMI and IR up to 230 feet (70 meters) using one CAT5e (or better) cable •With Infrared control signal passing through function. •Supports high bit-rate audio formats (Dolby True-HD / DTS Master Audio ) •HDCP compliant. •CEC Pass-Through •RS-232 Pass-Through (Output1) •DC 5V power supply 8 -5 to +35 C(+23 to +95 F) 5 to 90%RH (No Condensation) 300MHz/9Gbps Up to 1080p@60Hz@48 b/pixels, support 3D ,4K HDMI receptacle. RJ45 Power connector terminal Power DC receptacle IR Blaster D-Type 9pin plug 1080P 230FT/70m over single CAT5E/6 cable TABLE OF CONTENTS Package Contents Dimensional drawing Panel Descriptions Connecting and Operating Typical Application Maintenance Product Service Warranty Packing contents 1) Main Unit: 1x2 HDBaseT Splitter 2) Power supply DC 5V 3A 3) IR-TX cable x 2PCS 4) IR-RX cable x 2 PCS 5) M3x5 Screw x 6PCS 6) Operating Instructions 7) Mounting ear Dimensional drawing 30mm 110-240V/ 5VDC 3A power supply 10Watts Cold-Rolled (Cold Rolled) Steel W200xH116xT30mm 630g 116mm 200mm