Transcript
G-106/G-106Ex Warp Processor G-106 is multiple purpose video processor with warp, de-warp, video wall control, format conversion, scaler switcher, PIP/POP, 3D format conversion, image cropping and flip/rotation. In addition to above functions, G-106Ex also has embedded edge blending function. Each G-106 has 3 input ports (1x HDMI, 1x DP, 1x DVI-I) to support 5 input formats (HDMI, DP, VGA, DVI-D, YPbPr) and 1x 4K HDMI output port. One HDMI loop out port can provide raw signal output for daisy chain connection to other processor. Input ports support up to 3840x1080 @60Hz and 4k UHD @30Hz resolution with 4:4:4 full color sampling. It is integrated with 10-bit high end processor with motion adaptive de-interlace, low angle smooth algorithm and 3:2/2:2 pull-down film mode processing. PIP (picture in picture) and POP (side by side) are standard functions. It can display two landscape contents on one portrait LCD at top/bottom position. Advanced warp technology is embedded in G-106. User can use front panel keypad, IR controller or PC to perform edge blending and sophisticated geometry alignment up to 17x17 grids. Each corner geometry adjustment range is up to H:+_600 pixels and V: +_400 pixels in full HD output through remote controller. If using PC tool, the range can be double. G-106Ex can perform curved screen edge blending with color adjustment and white balance correction. Edge blending region gamma correction and non-edge blending area black level uplift are also standard function in G-106Ex. HDMI loop out supports daisy chain connection up to 3840x1080 @60Hz or 4k/2k @30Hz and allows display with multiple G-106 cascaded. Video wall function in G-106 is to crop and allocate source image for each projector. Complete curved edge blending can be achieved without PC, video distributor and splitter. In order to optimize video performance, G-106 is designed to support non-VESA standard input timing and allow user to create any EDID timing in the range between 1024x768 and 3840x2160. G-106 is an ideal solution for image geometry alignment, image warp/de-warp, PIP/POP and image flip/rotation. It provides easy configuration, low entry barrier, cost effective, reliable and flexible solution.
Features: 1.
Input and output: a、 Input ports: 1x HDMI, 1x DisplayPort and 1x DVI-I (support HDMI, DVI, VGA, YPbPr input signals)
HDMI & DisplayPort support 4k/2k @30Hz, WQXGA & 3840x1080 @60Hz with 4:4:4 sampling
without compression.
DVI-I port: if the input is through HDMI cable, it can support 4k/2k @30Hz. If input from DVI or VGA signal source, it can only support up to 1920x1200 @60Hz.
Connect with all kinds of video sources and support none VESA standard input resolution.
b、 Output ports: 1x HDMI. Preset output resolution: 720x480、XGA、WXGA、1280x1024、1366x768、 1400x1050、1600x1200、1920x1080 & 1920*1200。 c、 Loop out port: 1x HDMI (supports 3840*2160@30Hz) for daisy chain connection and monitoring. 2.
Warp and geometry alignment: a、 With full functions for quick 4 corner alignment, vertical and horizontal keystone correction, Pincushion & Barrel adjustment, image warp and image rotation and flip. b、 Each unit controls one projector and can be expanded with multiple G-106 to support unlimited number of projectors. c、 Integrated with full function front panel keypads and IR remote controller. Manual geometry alignment up to 9*5 grid patterns. The geometry adjustment range is up to +_600 in horizontal direction and +_400 pixels in vertical direction at one side in FHD output. d、 PC software tool is available for warp and geometry alignment up to 17x17 grid pattern. After finishing geometry alignment, the parameters can be stored inside G-106, then no more PC is needed. The geometry adjustment range will be double if compared with remote controller adjustment, i.e. H=+_1200 pixels and V=+_800 pixels in full HD output resolution. e、 Through applying serial connection among several processing modules, user can expand geometry alignment range. It is convenient for special application required extreme big geometry adjustment range.
3.
Edge Mask: Able to do edge mask with black background in each edge up to 500 pixels.
4.
Image stacking Image stacking for flat and curved screen with multiple projectors to increase brightness.
5.
PIP/POP Multiple windows display
PIP function with selectable input selection in both main and PIP display windows
Flexible image size, aspect ratio, position adjustment through OSD or IR controller
Max. PIP size is 1024x768 resolution
POP function with selectable full screen or original aspect ratio.
Dual landscape contents displayed at portrait TV.
6.
Corner wall display
7.
Image flip
Image flip at 90/180/270 degrees with full screen display
Image flip at Front/Rear, Right/Left, Top/Bottom direction
Image rotation and maintain original aspect ratio
Dual landscape contents displayed on portrait LCD
8.
High end video processing
10-bit high bandwidth processor with 3D motion adaptive de-interlace, low angle algorithm and 3:2/2:2 film mode detecting and recovery.
Support up to 4k/2k @30Hz input with 4:4:4 full color sampling without compression.
Color adjustment, including preset display modes, hue, saturation, brightness, contrast sharpness adjustments and RGB separate adjustment.
9.
Format conversion Convert below input signal formats into HDMI output: HDMI, DisplayPort and DVI-I (support HDMI, DVI, VGA, YPbPr input signals)
10.
Video wall function
Video wall function to split, crop and location assignment with pixel based location shift up to 900 pixels at H&V directions.
Pixel by pixel precise bezel compensation.
Video wall control up to 15x15 matrix displays.
Image PIP/POP, flip and rotation function can be applied to video.
11. Image cropping There are two ways of image cropping through OSD by remote controller:
[Video Wall] menu: ZOOM, PAN and OVERLAP In combination with image split (ZOOM), location assignment (PAN) and H&V 900 pixels cropping position shift function (OVERLAP), user can crop any location of the image to show on the screen.
[WARP] menu User can use Warp function to do geometry adjustment function for the image, including image resizing, accurate position and change the shape of the image.
12. Image de-warp for camera or video system
Image de-warp can be implemented through Warp function.
De-Warp function can be applied to correct image distortion of any image. It can be also applied to de-warp for medical endoscope and fish eye lens in surveillance system.
13. Passive 3D display:
Decoding 3D formats from Blue Ray, Set Top Box, PC…for dual projector passive 3D display.
Convert active 3D signal up to 1080p @120Hz for full HD passive 3D display.
Support HDMI 1.4a 3D formats, including 1080p/24Hz frame packed, Side by Side, Top-Bottom, Line by Line and frame sequential for passive 3D display.
Support 3840x1080 side by side and 1080i/60Hz frame packed 3D from Sony FHD 3D camcorder.
Support PIP function in passive 3D display, both main and PIP windows are still with 3D effect.
Support passive 3D image geometry alignment, curved screen display and stacking.
Convert discrete RH/LH 3D signals into one side by side 3D format output.
Convert line by line 3D format into side by side 3D format.
HDMI splitter
14. 3D signal conversion In additional projector active 3D and passive 3D application, G-105 can convert below 3D formats into one Side by Side 3D format output to meet the requirement in most of 3D display: --RH/LH discrete 3D format --Line by line (line interleaved) --Frame packing --Frame sequential --Top-bottom 3D.
15. Edge blending (only in G-106Ex)
G-106Ex can execute 4 directions edge blending. No limitation in the number of projector.
Provide complete function for edge blending area fine-tune and color correction.
Precise black level uplift at selectable area to compensate light leakage in the projector.
White balance and individual color correction for each projector.
Able to perform flat & curved screen seamless edge blending, including irregular curved screen and 360 degrees curved screen.
Flexible display
Left display modes can be configured in 3 projector edge blending system: 1+1+1: Each projector can display independent content. 1+2: two projectors shows one content and another one
show
standalone content. All in one User can save all the settings in PROFILE and recall at any time by RS232 or remote controller.
Edge Blending with projector at portrait position
Able to execute edge blending with projector at portrait position to increase image height. G-106Ex can rotate the content and implement edge blending. It is not necessary to rotate the content in advance.
16. System control & others
Optional rack mount bracket. Professional design and reliable.
Full function front panel keypads, IR remote controller and RS232 control.
USB interface for code update and PC tool operation.
Internal grid pattern for easy geometry alignment.
Programmable EDID for user to create any EDID with timing between 1024x768 and 3840x2160.
BOX ID for convenient multiple units control at the same time.
Five preset Profiles to save user settings and can be recalled at any time.
Automatic power ON/OFF through input signal control. While no input signal is detected, it will shut down output so that user can power ON/OFF complete system through the control in signal source.
Gwarp PC tool for sophisticated geometry alignment up to 17x17 grids.
Dimension and weight: 303x160x45mm, 1.6kg
