Transcript
Optoway
GBB-7400G
1
***********************************************************************************************************************************************************************
GBB-7400G
(RoHS Compliant)
1310 nm TX / 1550 nm RX , 5V / 1.25 Gbps Multi-Mode WDM Gigabit Interface Converter (GBIC) **********************************************************************************************************************************************************************
FEATURES
DESCRIPTION
l l l l
The GBB-7400G series 1-fiber multi-mode optical transceivers meet the Gigabit Interface Converter (GBIC) specification Rev. 5.5. It satisfies the optical interface specifications defined in IEEE 802.3ah 1000BASE BX by using 1310 nm transmitter and 1550 nm receiver. The transmitter section uses a multiple quantum well laser and is a class 1 laser compliant according to International Safety Standard IEC 60825. The receiver section uses an integrated 1550 nm detector preamplifier (IDP) mounted in an optical header and a limiting post-amplifier IC. A PECL input / output logic interface is used. TTL RX-LOS output simplifies interface to external circuitry. A 20-pin SCA-2 host connector is used to connect the converter to the host system.
l l l l l l l l l l l
1-Fiber MM Gigabit Interface Converter (GBIC) Compliant with GBIC Specification Rev. 5.5 Compliant with IEEE-802.3ah 1000BASE Compliant with Fibre Channel FC-PH-2 for 100-M5-SN-1 and 100-M6-SN-1 Hot Pluggable Module with SC Connector 1310 nm LD Transmitter 1550 nm Receiver 500 m links with 62.5/125 µm MMF Cables 500 m links with 50/125 µm MMF Cables SCA-2 Host Connector Single +5 V Power Supply RoHS Compliant Differential PECL Inputs and Outputs TTL RX-LOS Output Class 1 Laser International Safety Standard IEC 60825 Compliant
APPLICATIONS l WDM Gigabit Ethernet Links l SONET/SDH Equipment Interconnect l Fibre Channel Links
LASER SAFETY This multi-mode transceiver is a Class 1 laser product. It complies with IEC 60825 and FDA 21 CFR 1040.10 and 1040.11. The transceiver must be operated within the specified temperature and voltage limits. The optical ports of the module shall be terminated with an optical connector or with a dust plug.
ORDER INFORMATION P/No. GBB-7400G
Bit Rate (Gb/s) 1.25
Distance (m) 0 to 500
TX (nm) 1310
RX (nm) 1550
Package SC GBIC
Temp (oC) 0 to 70
TX Power (dBm) -4 to -10
RX Sens. (dBm) -17
RoHS Compliant Yes
Absolute Maximum Ratings Parameter Storage Temperature Operating Case Temperature Power Supply Voltage Input Voltage Relative Humidity
Symbol Tstg Topr Vcc ---
Min -40 -5 -0.5 -0.5
Max 85 70 6 Vcc
Units o C o C V V
RH
5
95
%
Min 4.75
Typ 5 200
Max 5.25 250 70
Notes
Recommended Operating Conditions Parameter Power Supply Voltage Power Supply Current Operating Case Temperature Data Rate
Symbol Vcc ITX + IRX Topr
0 1000
1250
Units V mA o C Mb/s
**********************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail:
[email protected] http: // www.optoway.com.tw
12/1/2005 V2.0
Optoway
GBB-7400G
2
**********************************************************************************************************************************************************************
Transmitter Specifications (0 oC < Topr < 70 oC, 4.75V < Vcc < 5.25V) Parameter Optical Optical Transmit Power Output Center Wavelength Output Spectrum Width Optical Rise Time Optical Fall Time Relative Intensity Noise Total Jitter Max. Po at TX-Disable Asserted Electrical Differential Input Voltage Transmit Fault Load Transmit Fault Output-Low Transmit Fault Output-High TX-Disable Input - Low TX-Disable Input - High TX-Disable Assert Time TX-Disable Negate Time Time to initialize, includes reset of TX-FAULT TX FAULT from fault to assertion TX-Disable time to start reset
Symbol
Min
Typ
Max
Units
Notes
Po λ ∆λ tr tf RIN TJ
-10 1260
--1310
-4 1360 5 0.26 0.26 -120 227 -35
dBm nm nm ns ns dB/Hz ps dBm
1
VIH - VIL TX-FAULTLOAD VTX-FAULT-L VTX-FAULT-H V TX-DISABLE-L V TX-DISABLE-H t_off t-on t-int
0.65 4.7 0.0 Vcc – 0.5 0 2.0
2.0 10 0.5 Vcc + 0.3 0.8 Vcc + 0.3 10 1 300
Vp-p kΩ V V V V µs ms ms
100
µs
t-fault t-reset
RMS (σ) 20% to 80% value 20% to 80% value 2
3
µs
10
Notes: 1. Output power is power coupled into a 62.5/125 µm single mode fiber. 2. Measured with a 27-1 PRBS. 3. Pull-up resistor on host Vcc.
Receiver Specifications (0oC < Topr < 70oC, 4.75 V < Vcc < 5.25V) Parameter Optical Sensitivity Maximum Input Power Signal detect – Hysteresis Wavelength of Operation Optical Return Loss RX-LOS – Asserted RX-LOS – Deasserted Electrical Differential Output Voltage Data Output Rise Time Data Output Fall Time RX-LOS of Light Load RX-LOS Output Voltage --- Low RX-LOS Outpu Voltage --- High RX-LOS Assert Time (off to on) RX-LOS Deassert Time (on to off)
Symbol
Min
Typ
Max
Units
Notes
--Pin
---3 1.0 1480 12 ---31
---
-17 ---
4 4
-17 ---
dBm dBm dB nm dB dBm dBm
2.0 0.35 0.35 10 0.5 Vcc 100 100
Vp-p ns ns kΩ V V µs µs
ORL Pa Pd VOH - VOL TrRX-DAT TfRX-DAT RX-LOSLOAD VRX-LOS-L VRX-LOS-H TA,RX-LOS TD,RX-LOS
--1580 -----
0.37
4.7 0 2.4
5 Transition: low to high Transition: high to low
6
Notes: 4. Minimum sensitivity and saturation levels at BER=1E-12 for a 2 7-1 PRBS. 5. At least 30 dB optical isolation for the wavelength 1260 to 1360 nm. 6. Pull-up resistor on host Vcc.
***********************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail:
[email protected] http: // www.optoway.com.tw
12/1/2005 V2.0
Optoway
GBB-7400G
3
**********************************************************************************************************************************************************************
PIN ASSIGNMENT
PIN
Sequence
Description
1
RX-LOS
Signal Name
2
2 3 4 5 6 7 8 9 10
RGND RGND MOD-DEF(0) MOD-DEF(1) MOD-DEF(2) TX-DIABLE TGND TGND TX-FAULT
2 2 2 2 2 2 2 2 2
11 12 13 14 15 16 17 18 19 20
RGND -RX-DAT +RX-DAT RGND VCCR VCCT TGND +TX-DAT -TX-DAT TGND
1 1 1 1 2 2 1 1 1 1
Receiver Loss of Signal, logic high, open collector compatible, 4.7K to 10K ohm pull-up to VCCT on host Receiver Ground Receiver Ground TTL Low SCL Serial Clock Signal SDA Serial Data Signal Transmitter Disable, logic high, open collector compatible Transmitter Ground Transmitter Ground Transmitter Fault, logic high, open collector compatible, 4.7K to 10K ohm pull-up to V CCT on GBIC Receiver Ground Receiver Data Bar, Differential PECL, AC coupled Receiver Data, Differential PECL, AC coupled Receiver Ground Receiver +5V Supply Transmitter +5V Supply Transmitter Ground Transmitter Data, Differential PECL, AC coupled Transmitter Data Bar, Differential PECL, AC coupled Transmitter Ground
A sequence value of 1 indicates that the signal is in the first group to engage during plugging of a module. A sequence value of 2 indicates that the signal is the second and last group. The two guide pins on the connector are electrically connected to the transceiver circuit ground. These two guide pins make contact with circuit prior to sequence 1 signals.
Module Definition Module Definition 4
MOD-DEF(0) PIN 4
MOD-DEF (1) PIN 5
MOD-DEF (2) PIN 6
Interpretation by Host
TTL Low
SCL
SDA
Serial module definition protocol
Module Definition 4 specifies a serial definition protocol. For this definition, upon power up, MOD-DEF(1:2) appear as no connector (NC) and MOD-DEF(0) is TTL LOW. When the host system detects this condition, it activates the serial protocol. The protocol uses the 2-wire serial CMOS E 2PROM protocol of the ATMEL AT24C01A/02/04 family of components.
***********************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail:
[email protected] http: // www.optoway.com.tw
12/1/2005 V2.0
Optoway
GBB-7400G
4
**********************************************************************************************************************************************************************
PACKAGE DIAGRAM Units in mm
Note: Specifications subject to change without notice.
***********************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail:
[email protected] http: // www.optoway.com.tw
12/1/2005 V2.0
