Transcript
Optoway
GBB-7580-1590G
1
***********************************************************************************************************************************************************************
GBB-7580-1590G
(RoHS Compliant)
1590 nm TX / 1510 nm RX , 5V / 1.25 Gbps Single-Mode WDM Gigabit Interface Converter (GBIC) ***********************************************************************************************************************************************************************
FEATURES
DESCRIPTION
l l l l
The GBB-7580-1590G series single-mode optical transceivers meet the Gigabit Interface Converter (GBIC) specification Rev. 5.5. It satisfies the optical interface specifications defined in IEEE 802.3ah 1000BASE BX by using 1590 nm transmitter and 1510 nm receiver. The transmitter section uses a multiple quantum well DFB laser and is a class 1 laser compliant according to International Safety Standard IEC 60825. The receiver section uses an integrated 1510 nm detector preamplifier (IDP) mounted in an optical header and a limiting post-amplifier IC. A PECL input / output logic interface is used. TTL RX-LOS output simplifies interface to external circuitry. A 20-pin SCA-2 host connector is used to connect the converter to the host system.
l l l l l l l l l l l
1-Fiber SM Gigabit Interface Converter (GBIC) Compliant with GBIC Specification Rev. 5.5 Compliant with IEEE-802.3ah 1000BASE-BX Compliant with Fibre Channel FC-PH-2 for 100-M5-SN-1 and 100-M6-SN-1 Hot Pluggable Module with SC Connector 1590 nm DFB LD Transmitter 1510 nm Receiver Up to 80 km using Single-mode Optic Cable 24 dB Power Budget at Least SCA-2 Host Connector Single +5 V Power Supply RoHS Compliant Differential PECL Inputs and Outputs TTL RX-LOS Output Class 1 Laser International Safety Standard IEC 60825 Compliant
APPLICATIONS l WDM Gigabit Ethernet Links l SONET/SDH Equipment Interconnect l Fibre Channel Links
LASER SAFETY This single mode transceiver is a Class 1 laser product. It complies with IEC 60825 and FDA 21 CFR 1040.10 and 1040.11. The transceiver must be operated within the specified temperature and voltage limits. The optical ports of the module shall be terminated with an optical connector or with a dust plug.
ORDER INFORMATION P/No.
Bit Rate (Gb/s)
GBB-7580-1590G
1.25
Distance (km) 80
TX (nm) 1590 DFB
RX (nm) 1510
Package SC GBIC
Temp TX Power (oC) (dBm) 0 to 70 3 to -2
RX Sens. (dBm) -26
RoHS Compliant Yes
Absolute Maximum Ratings Parameter Storage Temperature Operating Case Temperature Power Supply Voltage Input Voltage Relative Humidity
Symbol Tstg Topr Vcc ---
Min -40 -5 -0.5 -0.5
Max 85 70 6 Vcc
Units o C o C V V
RH
5
95
%
Min 4.75
Typ 5 200
Max 5.25 300 70
Notes
Recommended Operating Conditions Parameter Power Supply Voltage Power Supply Current Operating Case Temperature Data Rate
Symbol Vcc ITX + IRX Topr
0 1000
1250
Units V mA o C Mb/s
***********************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail:
[email protected] http: // www.optoway.com.tw
12/1/2005 V2.0
Optoway
GBB-7580-1590G
2
***********************************************************************************************************************************************************************
Transmitter Specifications (0 oC < Topr < 70 oC, 4.75V < Vcc < 5.25V) Parameter Optical Optical Transmit Power Output Center Wavelength Output Spectrum Width Side Mode Suppression Ratio Extinction Ratio Optical Rise Time Optical Fall Time Relative Intensity Noise Total Jitter Max. Po at TX-Disable Asserted Electrical Differential Input Voltage Transmit Fault Load Transmit Fault Output-Low Transmit Fault Output-High TX-Disable Input - Low TX-Disable Input - High TX-Disable Assert Time TX-Disable Negate Time Time to initialize, includes reset of TX-FAULT TX FAULT from fault to assertion TX-Disable time to start reset
Symbol
Min
Typ
Max
Units
Notes
Po λ ∆λ SMSR ER tr tf RIN TJ
-2 1580
---
3 1620 1
1
0.26 0.26 -120 227 -35
dBm nm nm dB dB ns ns dB/Hz ps dBm
VIH - VIL TX-FAULTLOAD VTX-FAULT-L VTX-FAULT-H V TX-DISABLE-L V TX-DISABLE-H t_off t-on t-int
0.65 4.7 0.0 Vcc – 0.5 0 2.0
2.0 10 0.5 Vcc + 0.3 0.8 Vcc + 0.3 10 1 300
Vp-p kΩ V V V V µs ms ms
100
µs
30 9
t-fault t-reset
-20 dB width
20% to 80% value 20% to 80% value 2
3
µs
10
Notes: 1. Output power is power coupled into a 9/125 µm single mode fiber. 2. Measured with a 27-1 PRBS. 3. Pull-up resistor on host Vcc.
Receiver Specifications (0oC < Topr < 70oC, 4.75 V < Vcc < 5.25V) Parameter Optical Sensitivity Maximum Input Power Signal detect – Hysteresis Wavelength of Operation Optical Return Loss RX-LOS – Asserted RX-LOS – Deasserted Electrical Differential Output Voltage Data Output Rise Time Data Output Fall Time RX-LOS of Light Load RX-LOS Output Voltage --- Low RX-LOS Outpu Voltage --- High RX-LOS Assert Time (off to on) RX-LOS Deassert Time (on to off)
Symbol
Min
Typ
Max
Units
Notes
--Pin
---3 1.0 1480 12 ---40
---
-26 ---
4 4
-26 ---
dBm dBm dB nm dB dBm dBm
2.0 0.35 0.35 10 0.5 Vcc 100 100
Vp-p ns ns kΩ V V µs µs
ORL Pa Pd VOH - VOL TrRX-DAT TfRX-DAT RX-LOSLOAD VRX-LOS-L VRX-LOS-H TA,RX-LOS TD,RX-LOS
--1520 -----
0.37
4.7 0 2.4
5 Transition: low to high Transition: high to low
6
Notes: 4. Minimum sensitivity and saturation levels at BER=1E-12 for a 2 7-1 PRBS. 5. At least 30 dB optical isolation for the wavelength 1580 to 1620 nm. 6. Pull-up resistor on host Vcc. ***********************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail:
[email protected] http: // www.optoway.com.tw
12/1/2005 V2.0
Optoway
GBB-7580-1590G
3
***********************************************************************************************************************************************************************
PIN ASSIGNMENT
PIN
Sequence
Description
1
RX-LOS
Signal Name
2
2 3 4 5 6 7 8 9 10
RGND RGND MOD-DEF(0) MOD-DEF(1) MOD-DEF(2) TX-DIABLE TGND TGND TX-FAULT
2 2 2 2 2 2 2 2 2
11 12 13 14 15 16 17 18 19 20
RGND -RX-DAT +RX-DAT RGND VCCR VCCT TGND +TX-DAT -TX-DAT TGND
1 1 1 1 2 2 1 1 1 1
Receiver Loss of Signal, logic high, open collector compatible, 4.7K to 10K ohm pull-up to VCCT on host Receiver Ground Receiver Ground TTL Low SCL Serial Clock Signal SDA Serial Data Signal Transmitter Disable, logic high, open collector compatible Transmitter Ground Transmitter Ground Transmitter Fault, logic high, open collector compatible, 4.7K to 10K ohm pull-up to V CCT on GBIC Receiver Ground Receiver Data Bar, Differential PECL, AC coupled Receiver Data, Differential PECL, AC coupled Receiver Ground Receiver +5V Supply Transmitter +5V Supply Transmitter Ground Transmitter Data, Differential PECL, AC coupled Transmitter Data Bar, Differential PECL, AC coupled Transmitter Ground
A sequence value of 1 indicates that the signal is in the first group to engage during plugging of a module. A sequence value of 2 indicates that the signal is the second and last group. The two guide pins on the connector are electrically connected to the transceiver circuit ground. These two guide pins make contact with circuit prior to sequence 1 signals.
Module Definition Module Definition 4
MOD-DEF(0) PIN 4
MOD-DEF (1) PIN 5
MOD-DEF (2) PIN 6
Interpretation by Host
TTL Low
SCL
SDA
Serial module definition protocol
Module Definition 4 specifies a serial definition protocol. For this definition, upon power up, MOD-DEF(1:2) appear as no connector (NC) and MOD-DEF(0) is TTL LOW. When the host system detects this condition, it activates the serial protocol. The protocol uses the 2-wire serial CMOS E 2PROM protocol of the ATMEL AT24C01A/02/04 family of components.
***********************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail:
[email protected] http: // www.optoway.com.tw
12/1/2005 V2.0
Optoway
GBB-7580-1590G
4
***********************************************************************************************************************************************************************
PACKAGE DIAGRAM Units in mm
Note: Specifications subject to change without notice.
***********************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303 Tel: 886-3-5979798 Fax: 886-3-5979737 E-mail:
[email protected] http: // www.optoway.com.tw
12/1/2005 V2.0
