Transcript
ECONOMY SPRAYERS GC SERIES
Parts Manual For Models: GC400 & GC600 Rev. September 2014 Form: GCSeriesSprayersRev3.indd
TABLE OF CONTENTS SECTION 1
2
3
DESCRIPTION ................................................ PAGE
1.1 1.2
Introduction ....................................................................... 1 Purchaser’s Responsibility .............................................. 1 Serial Number Information ............................................ 1
2.1 2.2 2.3 2.4 2.5 2.6
Replacement Parts ..................................................... 2 - 10 GC400 Main Frame & Tank ........................................... 2 GC400 Parts List .......................................................... 3-4 GC600 Main Frame & Tank ........................................... 5 GC600 Parts List .......................................................... 6-7 Run of Fluids ................................................................... 8 Parts List .................................................................... 9-10 Limited Warranty .............................................................. 9
1
INTRODUCTION
This manual contains parts diagrams and replacement parts lists. Do not modify the equipment in any way. Unauthorized modification may impair the function and/or safety and could affect the life of the equipment. It is the responsibility of the owner to make sure the machine is maintained properly, and that all parts are in working order. Where replacement parts are necessary for periodic maintenance and servicing, genuine factory replacement parts MUST be used to restore your equipment to original specifications. The manufacturer will not be responsible for injuries or damages caused by use of unapproved parts and/or accessories. The manufacturer reserves the right to make improvements to the machinery and parts at any time and at their discretion. OPERATOR ORIENTATION - The directions left, right, front and rear, are as seen from the driver's seat and facing in the direction of travel.
1.1
PURCHASER’S RESPONSIBILITY
It is the responsibility of the purchaser and/or operator to.....
1.2
●
Inspect the equipment and replace or repair any parts that are damaged or worn which under continued operation would cause damage, wear to other parts, or cause a safety hazard.
●
Return the equipment or parts to the authorized dealer, from where it was purchased, for service or replacement of defective parts that are covered by warranty. (The factory may inspect equipment or parts before warranty claims are honored.)
●
Payment of all costs incurred by the dealer for traveling to or transporting the equipment for warranty inspection and or claims.
MODEL / SERIAL NUMBER NAME: ____________________________________ PURCHASED FROM: ____________________________ DATE OF PURCHASE: ___________________________ MODEL NUMBER: ______________________________ SERIAL NUMBER: ______________________________
1
2
REPLACEMENT PARTS 2.1
2
GC400 MAIN FRAME & TANK
2
REPLACEMENT PARTS (CONTINUED) 2.1
GC400 MAIN FRAME & TANK (Continued) REF.
QTY.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 38 42 43
2 2 2 2 1 1 1 1 1 2 3 2 3 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 8 2 1 1 1 1 1
PART NO.
DESCRIPTION
2100011 1800168 0102292 1800167 2100001 0102244 0102021 AG2052050 1600571 1500030 1700001 1400130 1400001 0600273 1500003 1600209 1400017 1700015 AG006100PE 1600235 1400074 1400062 1300146 AG502010.020 1700006 1400076 0600355 0600358 0600359 0600357 0600190 0600191 1800351 1800480 0600014 AG3522000 0600356 AG3522060 0600023
Single Complete Pivot 22-22 Washer 23 x 39 UNI 6592 R 40 Galvanized Nut M.22 x 1.5 PF Galvanized Washer Grower D.23 x 35 UNI L. 1751 Galvanized Pin R 3 Pin D.19 Frame GC400 Lock Ring G 1 1/4 Vipla Crystal Hose 12 x 17 L=750 Clamp BIF. A Spring 173 mm 16.8-17.7 Gasket D.32 x 21 x 2 Elbow Fitting D.13 1/2 Ring Nut 1/2 Tank Minnesota ATOM 400 LT NAT L Clamp Perfect 14 x 27 Tube Spiral D.20 L=650 Outlet Gasket 57.5 x 40 x 3 Gasket For Joint D.11.8 x 18 x 2 P Hose CO.PCV 10 x 19 80 Bar L=800 Body Jet Agitation Elbow Connector D.20 1/2 G Extension Cylindrical MF 1/2" Welding For Thread OR D.36 x 26 x 5 Nozzle D.2 Tie Rod 90 x 80 x 100 H120 Plug Handwashing Minnesota ATOM D.80 S/Gasket Flat Gasket D.56 x 80 x 2 Handwashing Plug Minnesota ATOM Tank Handwashing Minnesota ATOM NAT. Handwashing Valve Gasket Valve Tear A Rivet D.5 x 20 Aluminum Rivet TT AL 3 x 10 Tank Ring Group Double Valve Tie Rod 90 x 80 x 100 Tank Lid Tank Filter
3
2
REPLACEMENT PARTS (CONTINUED) 2.1
4
GC400 MAIN FRAME & TANK (Continued)
REF.
QTY.
44 45 46 48 49 50 51 52 53 54 55
1 1 1 2 5 5 1 1 1 1 1
PART NO.
DESCRIPTION
2600009 1700011 1400010 1800191 1800011 1800114 E.MATCIR05/600NA 0600360 0600361 1500008 0600356
Small Label Register Gasket D.40 x 25 x 4 Female Plug 1" 1/4 Nut Aut. High M12 Bolt TE UNI 5739 8.8 6 x 16 Galvanized Washer 6 x 18 UNI 6593 R40 Galvanized Clean Water Tank ATOM 500/600 NAT 48 LT. Tank Plug D.122 Spring Valve Plug Gasket D.122 SS Clamp INOX AISI/304 21 x 38/12.7 Tie Rod 90 x 80 x 100 H170
2
REPLACEMENT PARTS (CONTINUED) 2.2
GC600 MAIN FRAME & TANK
5
2
REPLACEMENT PARTS (CONTINUED) 2.2
GC600 MAIN FRAME & TANK (Continued)
REF.
QTY.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 38 42 43
2 2 2 2 1 1 1 1 1 2 3 2 3 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 8 2 1 1 1 1 1
6
PART NO.
DESCRIPTION
2100011 1800168 0102292 1800167 2100001 0102244 0102026 AG2052050 1600883 1500030 1700001 1400130 1400001 0600272 1500003 1600209 1400017 1700015 AG006100PE 1600235 1400074 1400062 1300146 AG502010.020 1700006 1400076 0600356 0600358 0600359 0600357 0600190 0600191 1800351 1800480 0600014 AG3522000 0600356 AG3522060 0600023
Single Complete Pivot 22-22 Washer 23 x 39 UNI 6592 R 40 Galvanized Nut M.22 x 1.5 PF Galvanized Washer Grower D.23 x 35 UNI L. 1751 Galvanized Pin R 3 Pin D.19 Frame GC600 Lock Ring G 1 1/4 Vipla Crystal Hose 12 x 17 L=1050 Clamp BIF. A Spring 173 mm 16.8-17.7 Gasket D.32 x 21 x 2 Elbow Fitting D.13 1/2 Ring Nut 1/2 Tank Minnesota ATOM 600 LT NAT L Clamp Perfect 14 x 27 Tube Spiral D.20 L=650 Outlet Gasket 57.5 x 40 x 3 Gasket For Joint D.11.8 x 18 x 2 P Hose CO.PCV 10 x 19 80 Bar L=800 Body Jet Agitation Elbow Connector D.20 1/2 G Extension Cylindrical MF 1/2" Welding For Thread OR D.36 x 26 x 5 Nozzle D.2 Tie Rod 90 x 80 x 100 H170 Plug Handwashing Minnesota ATOM D.80 S/Gasket Flat Gasket D.56 x 80 x 2 Handwashing Plug Minnesota ATOM Tank Handwashing Minnesota ATOM NAT. Handwashing Valve Gasket Valve Tear A Rivet D.5 x 20 Aluminum Rivet TT AL 3 x 10 Tank Ring Group Double Valve Tie Rod 90 x 80 x 100 Tank Lid Tank Filter
2
REPLACEMENT PARTS (CONTINUED) 2.2
GC600 MAIN FRAME & TANK (Continued)
REF.
QTY.
44 45 46 48 49 50 51 52 53 54 55
1 1 1 2 5 5 1 1 1 1 1
PART NO.
DESCRIPTION
2600009 1700011 1400010 1800191 1800011 1800114 E.MATCIR05/600NA 0600360 0600361 1500008 0600356
Small Label Register Gasket D.40 x 25 x 4 Female Plug 1" 1/4 Nut Aut. High M12 Bolt TE UNI 5739 8.8 6 x 16 Galvanized Washer 6 x 18 UNI 6593 R40 Galvanized Clean Water Tank ATOM 500/600 NAT 48 LT. Tank Plug D.122 Spring Valve Plug Gasket D.122 SS Clamp INOX AISI/304 21 x 38/12.7 Tie Rod 90 x 80 x 100 H170
7
2
REPLACEMENT PARTS (CONTINUED) 2.3
8
PUMP ASSEMBLY
2
REPLACEMENT PARTS (CONTINUED) 2.3
PUMP ASSEMBLY (Continued) REF.
QTY.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39
1 4 1 3 3 1 1 5 1 4 1 1 1 1 1 1 1 2 2 2 2 1 4 2 1 1 1 1 1 2 3 4 2 1 1 1 1 1 2
PART NO.
DESCRIPTION
0900098 1800034 AR1498 1800036 1800129 AR1519 AR550242 AR550350 AR550370 1500004 1600692 AR460 AR450145 1300226 AG1102325 AR1041220 1600882 1400057 1700066 1400013 AR160660 AR550390 1800186 1800021 AR320406 AR887 AR391240 AG006100PE 1600235 1300010 1300009 1800036 1800180 AR880830 AR550450 AR550460 1500003 1600209 1800120
Shaft B1 1000 CE A60 A60 Bolt TCEI UNI 5931 8.8 10 x 20 Z Outlet Side Bolt TE M10 x 25 UNI 5739 8.8 Galvanized Washer Grower UNI 1751 M.10 Cardan Joint "C" AR303 Ring Nut O-Ring Elbow Clamp Perfect 21 x 38 Spiral Hose D.25 L=1000 Pump AR403 SP SGC Flange Reducer M.F. CIL 449 1/2 1/4 Curve Adapter 3/4" F. D.25 Cross Fitting 3/8" Hose 25 x 37 Rotary Drill 20 L=1250 Curve Connector D.25 OR D.31 x 25 x 3 Fly Nut 1" 1/4 Bolt Flange Nut Aut. HIGH CL. 8 M 10 Bolt TE UNI 5739 8.8 8 x 20 Galvanized Bracket Reg. of Pression GS20 3 Ways Pressure Gauge D.63 0-24 BAR Gasket For joint D.11.8 x 18 x 2 P Hose CO. PCV 10 x 19 80 BAR L=800 Valve LH 3/8" x 1/2" A.5264 Cock RH 3/8" x 1/2" "Meteor" A.5263 Bolt TE M 10 x 25 UNI 5739 8.8 Galvanized Nut M8 UNI 5587 - 6.8 Galvanized O-Ring Ring Nut Elbow Clamp Perfect 14 x 27 Tube Spiral D.20 L=650 Flat Washer UNI 6592 M.8 Galvanized 9
2
REPLACEMENT PARTS (CONTINUED) 2.3
10
PUMP ASSEMBLY (Continued)
REF.
QTY.
40 41 46 47 48 49 50 51 52 53 54 55 56
2 2 4 1 1 1 1 1 1 1 1 1 1
PART NO.
DESCRIPTION
1800180 1800020 1800130 1600512 AG3122053 AG3102050.010 AG462200.040 AG3122003.030 AG462200.040 AG454237.090 AG3122000.020 1400069 AR1041210
Nut M 8 UNI 5587 - 6.8 Galvanized Bolt TE M8 x 16 UNI 5739 - 8.8 Galvanized Plain Washer UNI 6592 M.10 Spiral Hose D.25 L=600 Filter ASP 1" 1/4 FC 50 M Filter Body ASP. 1" 1/4 OR 2.62 x 58.42 3231 EPDM Filter OR 2.62 x 58.42 3231 EPDM OR 3.53 x 78.97 Cover Filter Filter Nut Adapter 3/8 GAS M-F
2
REPLACEMENT PARTS (CONTINUED) 2.4
PUMP ASSEMBLY AR403
11
2
REPLACEMENT PARTS (CONTINUED) 2.4
PUMP ASSEMBLY AR403 (Continued) REF. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 * 28 29 * 30 31 32 * 33 * 34 * 35 36 37 38 * 39
12
QTY.
PART NO.
DESCRIPTION
3 3 1 3 3 3 3 6 3 1 1 3 3 1 1 1 1 2 1 1 1 1 1 1 3 1 1 1 1 2 1 1 1 1 1 2 2 1 1
800090 800350 2387 1880050 1880110 1880060 1880120 380080 1880070 1880160 1500350 380241 850250 620330 50X65X8 DHK5020 1880190 1880180 1880170 47247 1461430 47120 550460 550450 780060 1880021 880831 OR293 550340 550350 550242 550370 390201 1880130 OR1872262 550331 1200440 1040310 650920
Pin, Diaphragm Washer, Cup Diaphragm Kit Sleeve Piston Ring Piston Pin, Piston Circlip, Piston Rod, Connecting Crankshaft Shield Washer D.8.5 Bolt M10 x 16 Circlip Oil Seal Bearing Seal Ring Ring Spacer Circlip I47 Bearing Circlip E20 Elbow Nut Bolt M6 x 25 Manifold O-Ring 15.54 x 2.62 O-Ring 29 x 3 Nipple 1" O-Ring 23.81 x 2.62 Nut Elbow O-Ring O-Ring O-Ring 18.72 x 2.62 Washer D.6.5 Bolt M6 x 30 Tank, Oil O-Ring
2
REPLACEMENT PARTS (CONTINUED) 2.4
PUMP ASSEMBLY AR403 (Continued)
REF.
QTY.
PART NO.
DESCRIPTION
40 41 42 43 44 45 46 47 48 49 50 * 51 52 * 53 54 55 56 * 57 58 59 60 61
1 2 1 1 1 1 1 1 1 3 1 9 1 6 3 3 1 2 2 1 6 1
1040320 540290 450145 1433 1620450 621370 961340 680350 800860 1880030 2388 1140450 1880010 OR2670178 280080 1880040 1880090 OR14178 880530 1880080 780050 620680
Cap Bolt M8 x 25 Flange Relief Valve Tee PTO Adapter Washer Bolt M8 x 35 Bolt M8 x 55 Head Check Valve Kit (with O-Rings Ref. #51) O-Ring 20.24 x 2.62 Housing O-Ring 26.7 x 1.78 Bolt M8 x 60 Cover Bracket L.H. O-Ring 14.1 x 1.78 Plug Bracket R.H. O-Ring 28.25 x 1.78 Tempered Key 6 x 6 x 30
Ref. 28 30 33 34 35 39 51 53 57
* KIT 2389 Part No. OR293 550350 390201 1880130 OR1872262 650920 1140450 OR2670178 OR14178
Qty. 1 2 1 1 1 1 9 6 2
13
2
REPLACEMENT PARTS (CONTINUED) 2.5
VALVE ASSEMBLY GS40
REF. 1 3 4 5 6 7 8 10 Ø 11 12 13 14 15
14
QTY. 1 3 2 1 2 1 2 1 1 1 1 1 1
PART NO.
DESCRIPTION
620220 130491 390270 450110 550350 550545 180370 320420 110121 320433 320511 390140 550460
Body, Lower Ball Valve R.H. Nut M8 Seat, Valve O-Ring 23.81 x 2.62 Pressure Gauge Bolt M8 x 25 Spring Valve Seat Retainer O-Ring 40 x 3.53 Gasket Elbow
2
REPLACEMENT PARTS (CONTINUED) 2.5 VALVE ASSEMBLY GS40 (Continued) REF.
QTY.
16 17 18 19 20 21 22 23 24 25 28 30 31 32 33 36 38 43 44 45 46
1 1 2 1 1 1 1 1 1 1 1 1 1 1 2 1 1 2 1 1 1
PART NO.
DESCRIPTION
550440 320410 320480 320460 320470 320490 320450 320440 110190 230120 320406 450145 550450 110130 160660 880830 180101 130492 1041210 1041220 881560
Threaded Adapter Body, Upper Pin Fork Lever Locking Clip Adjustment Nut Guide Spring Seat Bracket Flange Ring Nut Fitting Bolt M8 x 35 O-Ring O-Ring Ball Valve L.H. Extension Adapter Elbow
Ø KIT 1922 Ref. Qty. 11 5
Ref. 5 10 11 12
KIT 1757 Qty. Ref. 1 13 1 14 1 1
Qty. 1 1
15
2
REPLACEMENT PARTS (CONTINUED) 2.6
16
OPTIONAL SPRAYER BOOMS
2
REPLACEMENT PARTS (CONTINUED) 2.6
OPTIONAL SPRAYER BOOMS (Continued) REF.
QTY.
1 2 3 4 5 6 7 8 9 10 10 10 11 12 13 14 15 16 17 18 19 20 20 21 21 21 22 23 24 25 26 27 28 36 37 40 41 42 43
4 4 2 2 4 4 2 2 2 2 2 2 12 6 6 2 1 8 4 8 8 1 1 2 2 2 2 4 4 2 2 2 1 9-12-17 1 6 2 6 18-34
PART NO.
DESCRIPTION
0100097 1700021 2000011 1600024 1300003 1700010 0100111 1800186 1800041 2000018 2000002 2000011 0100098 1800059 1800180 1800200 0100102 0100107 0100108 1800130 1800036 2000012 2000003 0100118 0100104 0100110 0100105 0100106 1800165 2500002 1800212 1800195 0100103 1700022 1300022 1800179 0100112 1800014 P3400100
Blind Plug 1/2 Gasket 19 S S Tube 20/500 G28B 41 1/2 Complete Hose 10 x 19 l=620 Self Lock Nut Connector 10 x 19 Gasket Support G28B Self Lock Nut M10 Bolt M10 x 45 Stainless Steel Tube G14B Stainless Steel Tube G20B Stainless Steel Tube G28B Plate Bolt M8 x 25 Nut M8 Nut M16 Inferior Support G14B & G20B Plate Clamp Washer 10 Bolt M10 x 25 Stainless Steel Tube G14B & G28B Stainless Steel Tube G20B Support G14B Support G20B Support G28B Pin Washer 20 x 55 Washer 20 Spring Nut M20 x 1.5 Nut M14 Superior Support G14B & G20B Gasket 10 Nipple MF 1/2 - 3/8 Nut M6 Support Bolt M6 x 20 Bolt & Nut 17
2
REPLACEMENT PARTS (CONTINUED) 2.6
OPTIONAL SPRAY BOOMS (Continued) REF.
QTY.
44 45 46 47 48 49 50 51 52 52A 53 54
9-12-17 9-12-17 9-12-17 9-12-17 9-12-17 9-12-17 9-12-17 9-12-17 9-12-17 9-12-17 9-12-17 9-12-17
PART NO.
DESCRIPTION
400020.030 402225.010 00226010 400020.020 00226011 00226002 02311000 02309010 30-04F80RE 30-03F110UB 402900 402225C
O-Ring D.6 x 2.5 Nozzle Body Diaphragm, Anti-Drip Nozzle Clamp Anti-Drip Assembly Nut 3/4" GAS Filter Gasket Jet 80O (Red) Jet 110O (Blue) Cap, Quick Coupling Complete Nozzle Assembly (96)
G20B 12
G28B 17
Quantity Count: G14B 9
18
2
REPLACEMENT PARTS (CONTINUED) 2.7
NOZZLE SPACING
GPM (Per Nozzle)
=
GPA
=
GPM GPA MPH W
-
If the nozzle spacing on your boom is different than those tabulated, multiply the tabulated GPA coverages by one of the following factors.
GPA x MPH x W 5940
5940 x GPM (Per Nozzle) MPH x W Gallons Per Minute Gallons Per Acre Miles Per Hour Nozzle spacing in inches for broadcast spraying Spray width in inches for single nozzles, band spraying or boomless spraying row spacing in inches divided by the number of nozzles per row for directed spraying
Where Tables Are Based on 20" Nozzle Spacing Other Spacing 8" 10" 12" 14" 16" 18" 22" 24" 30" Conversion Factor 2.5 2 1.7 1.4 1.3 1.1 0.9 0.8 0.7
Where Tables Are Based on 40" Nozzle Spacing Other Spacing 28" 30" 32" 34" 36" 38" 42" 44" 48" Conversion Factor 1.4 1.3 1.3 1.2 1.1 1.1 1 0.9 0.8
Tractor Speeds
SUGGESTED MINIMUM SPRAY HEIGHTS Spray Spray Height Angle 20" Spacing 65 73 80 110
Speed Time Required in SECONDS In MPH to Travel a Distance of: (miles per hour) 100 feet 200 feet 300 feet 3.0 23 45 68 3.5 20 39 58 4.0 17 34 51 4.5 15 30 45 5.0 14 27 41 6.0 23 34 7.0 19 29 7.5 18 27 8.0 17 26 9.0 15 23
22" to 24" 20" to 22" 17" to 19" 10" to 12"
ºSpray angles apply to flat spray tips spraying at rated pressure of 40 P.S.I. Lower pressures will result in reduced spray angles, except for the XR TeeJet.
**Adjust spray height in the field to overlap approximately 30% of each edge of pattern.
Tip Color
Tip No. (Strainer Screen Size)
Liquid Pressure in PSI
Capacity 1 Nozzle in GPM
4 MPH
5 MPH
6 MPH
7 MPH
Orange
8001 LP (100 Mesh) 80015 LP (50 Mesh) 8002 LP (50 Mesh) 8003 LP (50 Mesh) 8004 LP (50 Mesh) 8005 LP (50 Mesh) 8006 LP (No Strainer) 8008 LP (No Strainer) 8010 LP (No Strainer)
15 20 30 40
.10 .12 .14 .16 .15 .17 .21 .24 .20 .23 .28 .33 .30 .35 .42 .49 .40 .46 .57 .65 .50 .58 .71 .82 .60 .69 .85 .98 .80 .92 1.10 1.30 1.0 1.2 1.4 1.6
7.4 8.6 10.5 12.1 11.1 12.9 15.8 18.1 14.9 17.2 21.0 24.0 22 26 32 36 30 34 42 48 37 43 53 61 45 51 63 73 59 69 84 97 74 86 105 121
5.9 6.9 8.4 9.7 8.9 10.3 12.6 14.5 11.9 13.7 16.8 19.4 17.8 21.0 25.0 29.0 27 27 34 39 30 34 42 48 36 41 50 58 48 55 67 78 59 69 84 97
5.0 5.7 7.0 8.1 7.4 8.6 10.5 12.1 9.9 11.4 14.0 16.1 14.9 17.2 21.0 24.0 19.8 23.0 28.0 32.0 25 29 35 40 30 34 42 48 40 46 56 65 50 57 70 81
4.2 4.9 6.0 6.9 6.4 7.4 9.0 10.4 8.5 9.8 12.0 13.8 12.7 14.7 18.0 21.0 17.0 19.6 24.0 28.0 21 25 30 35 25 29 36 42 34 40 48 55 42 49 60 69
Green Yellow Blue Red Brown Grey White
15 20 30 40 15 20 30 40 15 20 30 40 15 20 30 40 15 20 30 40 15 20 30 40 15 20 30 40 15 20 30 40
Gallons Per Acre - 20" Spacing
19
2
REPLACEMENT PARTS (CONTINUED) 2.8
20
DRIVELINE ASSEMBLY
REF.
QTY.
PART NO.
DESCRIPTION
1 2 3 4 5 6 7 8 9 10 11 12
2 2 1 1 1 1 1 1 1 1 2 1
507010351 41201 204016851 341036000 225020933 225010933 341037000 204016852 255010005 255010006 252000001 5N01086N1
Yoke 1 ⅜", 6-Spling Cross Kit #1 Outer Tube Yoke Roll Pin Outer Drive Tube Inner Drive Tube Roll Pin Inner Tube Yoke Outer Shield Bearing Inner Shield Bearing Safety Chain Complete Shield
3
LIMITED WARRANTY
GEARMORE, INC., warrants each new Gearmore product to be free from defects in material and workmanship for a period of twelve (12) months from date of purchase to the original purchaser. This warranty shall not apply to implements or parts that have been subject to misuse, negligence, accident, or that have been altered in any way. Our obligation shall be limited to repairing or replacement of any part, provided that such part is returned within thirty (30) days from date of failure to Gearmore through the dealer from whom the purchase was made, transportation charges prepaid. This warranty shall not be interpreted to render us liable for injury or damages of any kind or nature, direct, consequential or contingent, to person or property. This warranty does not extend to loss of crops, loss because of delay in harvesting or any other expenses, for any other reasons. Gearmore in no way warranties engines, tires, or other trade accessories, since these items are warranted separately by these respective manufacturers. Gearmore reserves the right to make improvements in design or changes in specification at any time, without incurring any obligations to owners or units previously sold. Please be advised that all warranty work done by your dealer must be approved by Gearmore before work begins. GEARMORE, INC. 13477 Benson Ave. Chino, CA 91710 Always refer to and heed machine operating warning decals on machine.
Please fill out the warranty registration form and return to Gearmore. You will find the form on our website www.gearmore.com and can submit it online or print and mail to Gearmore, Inc.
21
