Transcript
GHANI FREESTANDING TUB FAUCET INSTALLATION INSTRUCTIONS Before you begin, read the installation instructions below. Observe all local plumbing and building codes. Unpack and inspect faucet and parts for damage. If any damage is found, contact Customer Service at 1-866-855-2284 and return faucet to container. If you need assistance while installing your new faucet, call our Customer Service number. Your application and circumstances may call for variations to the installation instructions. We recommend consulting a professional if you are unfamiliar with installing bathroom fixtures and plumbing. Signature Hardware accepts no liability for any damage to the floor, walls, plumbing, or personal injury during installation.
TOOLS AND MATERIALS: Adjustable Wrench Level Pencil Damp Cloth
Tape Measure Straight Edge Drill Protective Clothing
Plumber’s Tape Silicone Sealant Loctite Thread Sealant Safety Glasses
INSTALLATION Part
Qty
1. Faucet Body
1
2. Decorative Escutcheon
1
3. A Screw
2
4. A Gasket
2
5. Base
1
6. B Screw
6
7. B Gasket
10
8. C Screw
4
9. Installation Plate
2
10. Handshower
1
11. Shower Hose
1
12. Plastic Guard
1
13. Test Plate
1
14. Rubber Plug
2
15. 5.0 mm Allen Wrench
1
16. 6.0 mm Allen Wrench
1
Ghani Freestanding Tub Faucet Installation Instructions
1
1. Attach the Base (5) to the Plates (9) with the C Screws (8) and B Gaskets (7).
2. Use the Base (5) as a template to mark the location of the mounting holes on wood blocking. Make sure the wood is 1-3/8"-1-15/16" thick.
15. 5.0 mm Allen Wrench Wood Blocking
8. C Screw
9. Installation Plate
35-50 mm
5. Base
1-3/8"- 1-5/8"
7. B Gasket
Mounting Holes 8. C Screw
5. Base
7. B Gasket 9. Plate
Mounting Holes
Ghani Freestanding Tub Faucet Installation Instructions
2
3. Drill mounting holes with the appropriate drill bit. Attach the Base (5) to the wood blocking with the B Screws (6), and B Gaskets (7).
4. Connect the hot and cold water supplies. Attach the Rubber Plugs (14), and Test Plate (13) to the Base (5) with the A Screws (3) and A Gaskets (4).
Mounting Holes
16.
6.0mm Allen Wrench
3.
Screw A
4.
Gasket A
13.
Test Plate
14.
Rubber Plug
Mounting Holes
Cold Water 6. Screw B 7. Gasket B
Hot Water Wood Blocking
Wood Blocking
Floor
Ghani Freestanding Tub Faucet Installation Instructions
3
5. Put the Plastic Guard (12) onto the Base (5). Install the finished floor. When the finished floor is installed remove the Plastic Guard (12), Rubber Plug (14), and Test Plate (13).
6. Attach the Faucet Body (1) to the base (5) with the A Screws (3), and A Gaskets (4). Make sure the body is firmly in place and tighten the screws with the 6.0 mm Allen Wrench (16).
12. Plastic Guard
3. Screw A 4. Gasket A 13. Test Plate 14. Rubber Plug
Min 50 Min 1-15/16"
12. Plastic Guard
Ghani Freestanding Tub Faucet Installation Instructions
4
7. Connect the handshower (10) to the Faucet Body (1) with the Shower Hose (11).
8. Turn the water on to make sure that all connections are tight, no water should be leaking. Push the Decorative Escutcheon (2) into place, and finish the floor.
Ghani Freestanding Tub Faucet Installation Instructions
5
USAGE: •
Raise the handle to make the water flow. Turn the handle to the left for hot, and to the right for cold.
•
Pull the diverter up to divert the water to the handshower. Push the diverter down to diver the water to the faucet spout.
Ghani Freestanding Tub Faucet Installation Instructions
6
