Transcript
skeye.allegro | skeye.allegro LS HW 90250/V4 | HW 90260/V4 with Android 2.3.6 (Gingerbread) Version 1.1
USER GUIDE
Unless consent is given explicitly, any forwarding or copying of the documentation herein, its use and disclosure of the contents is not permitted. Any violations shall be subject to damages. All rights reserved in the case of a patent or utility patent registration.
© Höft & Wessel AG 2014 Subject to amendment, errors excepted BHB_skeye-allegro_V4_Android_1-1_EN.doc
TABLE OF CONTENTS
Table of Contents 1.
Introduction ......................................................................................................... 5
1.1 Document Information ....................................................................................... 5 1.2 Amendment Index ............................................................................................. 5 1.3 Characteristics .................................................................................................. 6 1.4 Purpose of the Document ................................................................................... 6 1.5 Readership ....................................................................................................... 6 1.6 Terminology ...................................................................................................... 6 1.7 Intended Use .................................................................................................... 7 1.8 Explanations on this Manual ................................................................................ 8 1.8.1 Note Pictograms .......................................................................................... 8 1.8.2 Registered Trademark .................................................................................. 9 1.9 Safety Notes ..................................................................................................... 9 1.9.1 General Safety Notes ................................................................................... 9 1.9.2 Safety Notes on the Lithium-Ion Battery ....................................................... 11 1.9.3 Safety Notes on the Communication Cradle/Battery Recharger ........................ 14 1.9.4 Safety Notes on the Power Supply ............................................................... 15 1.9.5 Safety Notes on the Laser ........................................................................... 15 1.9.6 Safety Notes on the Imager with LED Aimer .................................................. 16 1.9.7 Safety Notes on the Imager with Laser Aimer ................................................ 16 1.9.8 Safety Notes on Mobile Radio ...................................................................... 16 1.9.9 Safety Notes on Wireless LAN/Bluetooth ....................................................... 17 1.9.10 Safety Notes on Using GPS ......................................................................... 17 1.9.11 Safety Notes on Data Loss .......................................................................... 17 1.10 Disposal ......................................................................................................... 17 2.
The skeye.allegro ............................................................................................... 18
2.1 Variants ......................................................................................................... 2.2 Hardware Equipment ........................................................................................ 2.3 Software Equipment ......................................................................................... 2.4 Accessory ....................................................................................................... 2.5 Communication Cradles .................................................................................... 2.6 Views ............................................................................................................. 2.6.1 Front View ................................................................................................ 2.6.2 Rear View ................................................................................................. 2.7 Keyboard ........................................................................................................ 3.
Taking into Operation ......................................................................................... 24
3.1 Using the SD Card ........................................................................................... 3.2 Using the SIM Card* ........................................................................................ 3.3 Battery ........................................................................................................... 3.3.1 Inserting the Battery .................................................................................. 3.3.2 Replacing the Battery ................................................................................. 3.3.3 Charging the Battery .................................................................................. 3.4 Switching On/Switching Off the skeye.allegro ...................................................... 3.4.1 Switching On ............................................................................................. 3.4.2 Switching Off ............................................................................................ 3.4.3 Suspend Mode ........................................................................................... 3.4.4 Automatic Standby (Display Timeout) .......................................................... 3.4.5 Complete Power Off ................................................................................... 4.
18 19 19 19 20 21 21 22 23 24 25 26 26 27 28 29 29 29 29 29 31
Initial Steps ........................................................................................................ 32
4.1 Operating the skeye.allegro with the Stylus ........................................................ 4.2 Using the Navigation Key .................................................................................. 4.3 Android – Basics .............................................................................................. 4.3.1 Home Screen ............................................................................................ 4.3.2 Basic Settings ........................................................................................... 4.3.3 Symbols on the Android Status Bar .............................................................. 1.1 15.10.2014
32 32 33 33 34 35
3
TABLE OF CONTENTS
4.3.4 Showing/Hiding the Keyboard ..................................................................... 35 4.3.4.1 Setting the Brightness .......................................................................... 36 4.3.4.2 Setting the Properties of the Input Panel (Keyboard) ................................ 38 5.
Further Functions and Settings ........................................................................... 40
5.1 Scanner Operation ........................................................................................... 5.1.1 BarcodeScanner (skeye) ............................................................................. 5.1.1.1 Scanning ............................................................................................ 5.1.1.2 Settings .............................................................................................. 5.2 System Information (SysInfo) ........................................................................... 5.2.1 Creating a SysInfo Report File ..................................................................... 5.2.2 Calling the SysInfo Report File ..................................................................... 5.3 Sound ............................................................................................................ 5.4 Switching the Radio Modules On and Off ............................................................. 5.5 Updating the Operating System ......................................................................... 6.
Radio Modules .................................................................................................... 55
6.1 6.2 6.3 6.4 7.
Wireless LAN ................................................................................................... Mobile Radio ................................................................................................... Bluetooth ........................................................................................................ GPS* .............................................................................................................
55 57 59 60
Communication Cradles ...................................................................................... 61
7.1 Communication Cradle HW 50250 and 50253 - View ............................................ 7.2 Connections of HW 50250 (USB, Standard) ......................................................... 7.3 Connections of HW 50253 (Ethernet) ................................................................. 7.4 Technical Data HW 50250/HW 50253 ................................................................. 7.5 Connecting the Communication Cradle ............................................................... 7.5.1 HW 50250 ................................................................................................ 7.5.2 HW 50253 ................................................................................................ 7.6 LED Function Display........................................................................................ 7.6.1 HW 50250 ................................................................................................ 7.6.2 HW 50253 ................................................................................................ 7.7 Charging the Battery in the Communication Cradle .............................................. 8.
40 42 42 44 45 47 48 51 53 54
61 62 62 63 65 65 66 67 67 68 69
Technical Data .................................................................................................... 70
8.1 Modules .......................................................................................................... 71 8.1.1 Barcode Scanner ....................................................................................... 73 8.1.2 Imager ..................................................................................................... 74 9.
Troubleshooting ................................................................................................. 75
9.1 9.2
Reset via Hardware .......................................................................................... 75 Resetting the Device to Factory Settings ............................................................. 76
10. Appendix ............................................................................................................ 77 10.1 10.2 10.3
4
Glossary ......................................................................................................... 77 Index ............................................................................................................. 80 Manufacturer's Address .................................................................................... 83
1.1 15.10.2014
INTRODUCTION Document Information
1.
Introduction The skeye.allegro of the 3. generation is a mobile data capture device. It supports all kind of applications in the retail & logistics industry and the field service. The skeye.allegro meets all the requirements for modern data capture:
Connection to a wireless LAN network, Bluetooth devices and GSM/GPRS networks Use of SD memory cards Data capture via laser scanner, imager or RFID
Designed for one-hand operation, the powerful skeye.allegro ensures for an ergonomic working situation. It is handy and the advanced power management makes it the ideal solution for long fatigue-free working sessions. Due to its IP65 rating it can be used in even demanding environments. The skeye.allegro supports common standard applications for mobile terminals and modern Android software with a graphical user interface as well as the use of standard applications such as Internet browser, Android Explorer, Barcode Scanner, Calculator, Calendar, Camera, etc. The current generation of the mobile data capture devices skeye.allegro and skeye.allegro LS are equipped with a powerful Marvell PXA 320 processor and the Android (Gingerbread) operating system. All modules and antennas required for radio transmission are integrated. The SD and SIM card slots accessible for the user are protected by a protective cover.
1.1
Document Information Product: Type of document: Version: Author:
1.2
skeye.allegro (LS) | (HW 90250-60/V4) with Android 2.3.6 USER GUIDE 1.1 Lin Höft & Wessel AG, Hannover
Amendment Index Version:
Changes:
Date:
By:
01.00 01.10
First version/Translation Changes/Corrections
30.09.2014 15.10.2014
LIN/GH LIN
1.1 15.10.2014
5
INTRODUCTION Characteristics 1.3
Characteristics The current versions of the skeye.allegro of the 3. generation differ from the previous models of the 2. generation by the following features:
Operating System Android 2.3.6 (Gingerbread) Marvell PXA 320 806 MHz (Monahans) processor
Identification: Having removed the battery (see chapter 3.3.2) the sticker with the serial number becomes visible. HW 90250/V4… or HW 90260/V4...
Sticker serial number
Designation Fig. 1: Sticker serial number
It also contains the features of the device (see chapter 8.1) On the "HWI-Block" tab (All Apps (x = 0 / 1 / 2 ...).
1.4
Sysinfo) "Revision 3.x" is displayed
Purpose of the Document The documentation provided describes the functions and settings of the skeye.allegro, contains important usage instructions and information on the peripheral devices and technical data.
1.5
Readership The documentation is intended for people operating the skeye.allegro.
1.6
6
Terminology skeye.allegro Portrait Edition or HW 90250/V4
Portable Data Terminal (in the following also referred as mobile terminal).
skeye.allegro LS Landscape Edition or HW 90260/V4
Portable Data Terminal with landscape display (in the following also referred to as mobile terminal).
1.1 15.10.2014
INTRODUCTION Intended Use Battery HW 19200 HW 19201 HW 19202
Rechargeable lithium-ion battery (storage battery) with different capacities to supply the mobile terminal with power.
2-slot Battery Recharger HW 16200
Charging device for no more than 2 batteries of type HW 19200 or HW 19201
4-slot Battery Recharger HW 16250/4 (V2)
4-slot Battery Recharger for HW 90250/V4 und HW 90260/V4.
Communication Cradle HW 50250 (V3C3C4) Communication Cradle HW 50253 (V1C2)
USB communication cradle (host or device, switchable) for the mobile terminal HW 90250/V4 and HW 90260/V4.
4-slot Communication Cradle HW 50250/4 (V2) HW 50251/4 (V2)
4-slot Communication Cradle USB (HW 50250/4) and Ethernet (HW 50251/4) for HW 90250/V4 and HW 90260/V4.
Power Supply Unit HW 14200
Wide range switched mode power supply unit to provide the mobile terminal, battery recharger and communication cradle with power.
Power Supply Unit HW 14204
Wide range switched mode power supply unit to provide the 4slot communication cradle and 4-slot battery rechargers with power.
Car Cradle HW 51250
Holds the device and supplies the HW 90250/V4 and HW 90260/V4 with power inside the motor vehicle.
SD card slot
SD memory cards
Ethernet communication cradle for HW 90250/V4 and HW 90260/V4.
There are two display variants of the skeye.allegro: skeye.allegro and skeye.allegro Landscape see chapter 2.1.
1.7
Intended Use The skeye.allegro respectively skeye.allegro LS has been designed for use in the commercial sector and for acquiring and transferring data within buildings or vehicles or outside under moderate climate conditions. The skeye.allegro respectively skeye.allegro LS is not intended for use in private households. Please pay attention to the information of this user guide, especially the safety notes. Intended use means that the device must only be used and operated in accordance with the information contained herein. Any other use is not an intended use and may lead to property damage or even personal injury. Höft & Wessel does not accept any liability for damages caused by a usage other than the intended usage.
1.1 15.10.2014
7
INTRODUCTION Explanations on this Manual 1.8
Explanations on this Manual The User Manual is designed to enable you to get your skeye.allegro up and running quickly and is structured as follows:
Introduction
Taking into operation
Software
Communication/Data exchange
Troubleshooting
Annex
It is assumed that you are familiar with the basics of Android. In case of problems refer to the corresponding Android documentation. The documentation can be found here: https://support.google.com/nexus/s/answer/182077?hl=en-GB
1.8.1
Note Pictograms Safety notes in the text are always illustrated in the same way. In this manual the following safety notes are used: Personal injuries: CAUTION! Describes a hazardous situation with a low level of risk. If not avoided, the situation could result in minor or moderate injury.
Material damages: CAUTION! Describes a hazardous situation for things/devices. If not avoided, the situation could result in damages to the product or something nearby. Other: NOTE! Indicates important information required to complete a task.
Indicates an alternative method to complete a task or additional information on a topic.
8
1.1 15.10.2014
INTRODUCTION Safety Notes 1.8.2
Registered Trademark The following terms and names used in this manual are registered trademarks and products of the corresponding companies:
Android is a registered trademark of Google Inc., 1600 Amphitheatre Parkway Mountain View, California 94043, USA.
Other product and company names may be trademarks of other companies.
All trademarks mentioned and possibly protected by third parties are subjected to the ownership of the corresponding registered owners.
1.9
Safety Notes Carefully read and follow the user manual and the safety information mentioned in this chapter before performing further steps. You have to:
read keep the information in mind during work.
This is the precondition for secure working with the product undisturbed handling
1.9.1
General Safety Notes Transport and Storage: The device must only be shipped in original or comparable robust packaging. Shipping the device e.g. in a normal padded bag does not provide sufficient impact and pressure protection. Such improper packaging would fall under the definition of the term Negligence. The device must only be stored without battery in a dry environment. See also the notes in chapter 1.9.2. Connection: The device has to be connected to a USB 1.1 or higher interface. Otherwise, short circuit and fire may be caused. Handling: Never expose the skeye.allegro to very high temperatures e.g. behind the windscreen of a motor vehicle. Never insert any objects not intended for use with this device in the instrument’s openings.
1.1 15.10.2014
9
INTRODUCTION Safety Notes Operation: Do not use the mobile terminal permanently in an environment with high humidity. Do not dip it into fluid or wet it completely. Only use your mobile terminal with original equipment. Non-compliance voids the warranty. Do not operate your mobile terminal when you are in explosive areas, for instance in petrol stations, fuel depots, chemical plants, below deck in ships, near blasting operations, in locations where a large volume of dust particles (such as flour, wood or metal) is present in the air, LPG-operated vehicles, etc. We recommend switching off the device completely (see chap. 3.4.5). This also applies to places where you are usually advised to switch off your vehicle motor. Do not operate in close range of strong electromagnetic fields. Failures may be caused. Interference may be noticed near electric devices. Therefore, always pay attention to local safety regulations. Users with hearings aids must note that radio signals of electronic devices (with radio equipment) may launch into hearing devices causing an unpleasant noise. Maintenance, service, and disturbances: The mobile terminal is – apart from charging of the battery and the mentioned comments – lifetime maintenance-free and does not need special care. Do not try to open, repair or modify your skeye.allegro. The manufacturer will not be liable for any damage caused in that way. Apart from other things, the function for correctly charging the battery may be influenced. As a result, excessive charging voltage, uncontrolled charging and discharge current, leakage of harmful substances, excessive heat generation, bursting or fire may occur. Any tampering by non-authorised persons will invalidate the warranty. If your skeye.allegro needs to be repaired or maintained, please contact your specialised dealer. Clean the housing only with damp cloth and mild detergent.
10
1.1 15.10.2014
INTRODUCTION Safety Notes 1.9.2
Safety Notes on the Lithium-Ion Battery Carefully read the following safety notes to prevent an incorrect handling of the battery and to avoid possible dangers. Non-observance of the safety information or incorrect use of the battery can lead to excessive current flow, to the discharge of harmful substances, excessive heat development, explosion or fire. Transportation and storage: Do not transport or store the battery together with metal objects such as necklaces, hairpins, etc. Doing so may short circuit the battery, which could result in excessive current flow and possibly cause leakage of battery fluid, heat generation, bursting or fire. When carrying or storing batteries, use an electrically nonconductive (insulated) case.
When the equipment is expected not to be used for a long time do not store the batteries exceeding the appropriate conditions as listed below. Otherwise its performance will be degraded and its service life will be decreased. when the batteries are discharged and remain in the equipment: 1 week when the batteries are fully charged and remain in the switched off equipment: 1 month long-term storage: see next note.
When the battery is expected not to be used for a long time, take the battery out of the equipment and store it in a dry place at or below room temperature. For an optimum service life, the battery should be charged up to 20 to 40% when being stored. After 12 months at the latest the device should be charged and subsequently discharged. Otherwise, its performance will be degenerate and its service life will be decreased. Store the battery in a location where children cannot reach it. Also make sure that a child does not take out the battery from the charger or equipment being used. If a child swallows a battery, seek medical attention immediately. The storage temperature must not be below –20 or above +50°C. Ambient conditions: The temperature may not be outside the admissible operating and storage temperature range of -20 to + 60 degrees centigrade. The temperature may be within the range of 0 °C to + 40 °C during charging. Do not discard the battery into fire and do not leave it in a hot place such as near a fire or on a heater. Doing so melt the insulation, damage the sealing parts or protective devices, cause leakage of battery fluid (Electrolyte) from the batteries, bursting or fire. Do not immerse batteries in water or seawater, and do not allow them to become wet. Batteries which have become wet must always be replaced with new ones because internal short-circuits can cause dangerous heat emissions if further used. Do not throw batteries, and do not allow them to fall on hard surfaces. Connection: Do not connect the battery to an electrical outlet, e.g. vehicle cigarette lighter, power outlets, other power supply units, other charger, etc. Do not reverse the positive (+) and negative (-) terminals when inserting the battery. Since the mechanical design of the battery enables you to insert in one direction only, the battery must not be inserted into the opposite direction by force.
1.1 15.10.2014
11
INTRODUCTION Safety Notes Handling: Protective devices to prevent danger are built into the battery. To ensure for a proper operation, do not disassemble the battery or modify parts of it. If they are damaged, this could result in excessive charging voltage, control loss during charging or discharging, leakage of battery fluid, heat generation, bursting or fire. Do not disassemble Li-ion bare cells of the battery. There is the danger of flammable fluid being spilt. It may also cause an internal or external short circuit, leakage of battery fluid, heat generation, bursting or fire. Do not directly solder the battery. Doing so melt the insulation, damage the sealing parts or protective devices, cause leakage of battery fluid (Electrolyte) from the batteries, bursting or fire. Do not short-circuit the battery by directly connecting the positive (+) and negative (-) terminals with objects such as wire. Short circuiting generates heat which may damage the equipment. In the worst case this could result in leakage of battery fluid, bursting or fire. Do not put the battery into a microwave oven or pressurised container. This could result in leakage of battery fluid, bursting or fire. Do not pierce the battery with a nail or other sharp object, hit it with a hammer, or step on it. This could result in leakage of battery fluid, bursting or fire. Operation: For operation of the device use the delivered battery only. Please use the battery only for the determined purpose. Do not use the battery in any device other than those specified in this manual. Depending on the device being used, doing so may cause abnormal current flow, leakage of battery fluid, heat generation, bursting or fire. If the battery becomes discoloured or deformed, or in any way appears abnormal, stop using it. Return it to the distributor or manufacturer from whom you purchased it. Do not use or leave the battery in very high temperatures (for example, under strong direct sunlight). Otherwise, it may cause leakage of battery fluid, bursting or fire or its performance will be degenerate and its service life will be decreased. To ensure safety, the battery incorporates built-in safety devices. Do not use it in a location where static electricity is greater than what the manufacturer guarantees. Otherwise, the safety devices may be damaged, causing leakage of battery fluid, expose of fire. Do not use the battery in other than the following conditions. Otherwise, it can overheat or fire, or its performance will be degenerate and its service life will be decreased. when the battery is charged: 0 °C ~ +40 °C when the battery is discharged or stored: -10 °C ~ +50 °C Note: higher temperatures increase the self-discharge of the battery. Do not use the battery in combination with primary batteries (such as dry-cell batteries) or batteries of different capacities or brands. That may cause leakage of battery fluid, heat generation, bursting or fire. Do not connect different assembled batteries together. And also do not connect same assembled batteries in series, unless explicitly instructed by the user information to do so.
12
1.1 15.10.2014
INTRODUCTION Safety Notes Charging: When recharging, only use the battery charger specially provided by Skeye. Failure to follow proper charging procedures may cause excessive voltage, excessive current flow, loss of control during charging, leakage of battery fluid, heat generation, bursting, or fire. Do not use or charge the battery near a heat source such as fire or heater or in extremely hot weather. Do not charge a battery when it is cold (below 0 °C). This may cause impaired performance and shortening of battery service life. If a battery is to be used for the first time or it has not been used for a long time, be sure to charge it. Health hazards: If a battery leaks, and the electrolyte enters the eye, do not rub but rinse out thoroughly under flowing water and then seek medical assistance. Otherwise, eye damage can result. If a battery leaks and the electrolyte makes contact with clothing or the skin, the skin or clothing must be rinsed out under flowing water in order to prevent damage to the skin. Maintenance, service, and disturbances: Lithium-ion batteries have a predetermined operating life. If the operating time shortens excessively, this means that the battery life has expired. If it comes to that point, stop use immediately and replace with new batteries. Lithium-ion battery is a designated product of Recycle. The battery after using is a valuable resource. The return of the batteries ensures reuse of the chemicals contained. This recycling process avoids any impact to the environment. Höft & Wessel guarantees that all batteries returned are fed to the recycling process. When a battery is no longer usable, discharge it. When you dispose of the Lithium battery, insulate it by wrapping the terminals with tape. Mixing the battery with other metals or batteries may lead to fire, heat, or explosion. Then, return the battery to Höft & Wessel. As a part of its normal service, Höft & Wessel guarantees that all used batteries are fed to the recycling process. See also extract from BattG (act concerning the placing on the market, collection and environmentally compatible waste management of batteries and accumulators) of 25.06.2009: According to §9, section 1, sentence 1, manufacturers are obliged to take back batteries that have been handed in by distributors or public disposal departments (here, device batteries registered according to §13, sentence 1) free of charge and to treat and recycle them according to §14. Batteries that cannot be treated and recycled shall be disposed of according to §14 If Lithium-ion batteries are not fully charged after the battery charger’s predetermined charging period has elapsed, stop the charging process. Prolonged charging may cause leakage of battery fluid, heat generation or bursting of fire. If the battery leaks or gives off a bad odor, remove it from any exposed flame. Otherwise, the leaking electrolyte may catch fire, and the battery may explode or fire. If the battery gives off an odor, generates heat, becomes discolored or deformed, or in any way appears abnormal during use, recharching or storage, immediately remove it from the device or battery charger and stop using it.
1.1 15.10.2014
13
INTRODUCTION Safety Notes In case the battery terminals are dirty, clean the terminals with a dry cloth before use, otherwise, the contact with equipment may cause insufficiency, and power failure or charge failure.
1.9.3
Safety Notes on the Communication Cradle/Battery Recharger
The batteries may only be charged with the battery charging devices recommended by the manufacturer. The utilisation of another battery charger might be dangerous and leads to an end of the warranty.
Do not try to open, repair or modify your device. The manufacturer will not be liable for any damage caused in that way. Apart from other things, the function for correctly charging the battery may be influenced. As a result, excessive charging voltage, uncontrolled charging and discharge current, leakage of harmful substances, excessive heat generation, bursting or fire may occur.
If the communication cradle/battery recharger changes shape or colour, generates heat or in any way appears abnormal stop using it. Return it to the distributor or manufacturer from whom you purchased the device.
Use the communication cradle/battery recharger only with the supplied power supply. The main voltage must correspond to the technical data mentioned on the power supply.
Use the communication cradle/battery recharger only in dry, closed rooms and not in direct sunlight, e.g. behind windows.
The device has to be connected to a USB 1.1 or higher interface. Otherwise, short circuit and fire may be caused. Otherwise, excessive heat generation, bursting or fire may occur.
Keep the device out of the reach of small children.
14
1.1 15.10.2014
INTRODUCTION Safety Notes 1.9.4
1.9.5
Safety Notes on the Power Supply
Do not try to open and/or repair and/or alter the power supply. The manufacturer will not be liable for any damage caused in that way.
Use the power supply only with the power cable delivered.
Be sure to push the power cable cord always into an easily accessible socket.
The power cable has to be inserted completely into the table power supply. The other end is inserted into a socket. Be sure to push the prongs all the way in.
The outlet of the power supply has to be put all the way into the current supply of the device.
Always connect the power cable to the device before plugging it into the wall outlet.
Check that the plug is clean before plugging it in.
Do not place any objects on top of the cord.
Do not place the cord near heating equipment.
Do not connect cables other than those specified in this manual. Doing so may result in fire or improper operation.
Do not use a damaged cord.
Handle the power cord with care. Improper handling may lead to fire or shock.
Avoid excessive bending, twisting, and pulling of the cord.
When disconnecting the power cable, hold the plug firmly. Do not tug on the cord itself.
Use power supply and power cable only in dry rooms.
Safety Notes on the Laser If the type designation of your skeye.allegro contains option S5, your skeye.allegro is equipped with a laser (e.g.HW 90250/V4S5), please observe the following notes: The laser beam is classified as a class 2 laser according to the following standards: IEC 60825-1:2007 and EN 60825-1:2007 It is presumed that a short contact with this kind of laser beam does not do any harm, however, the following precautions are recommended:
Do not direct the laser beam to persons intentionally.
Do not look directly into the laser beam.
Do not manipulate the laser.
Do not attach optical accessory at the laser beam exit.
Do not observe the laser beam with optical instruments like magnifier, telescope or binoculars.
Be careful that no unintentional reflections at the surface are caused by the laser beam, which may lead to a focusing of the beam.
If you do not use the device store it in a place without access for trespassers.
1.1 15.10.2014
15
INTRODUCTION Safety Notes 1.9.6
Safety Notes on the Imager with LED Aimer If the type designation of your skeye.allegro contains option S7, your mobile terminal is equipped with an imager module with integrated LED aimer (e.g. HW 90250/V4S7). Please observe the following notes: The LED light source is classified as a class 1 LED according to the following standard: IEC 60825-1:2007. A class 1 LED is presumed to be safe under reasonably foreseeable conditions of operation. Even looking directly into the light beam by accident does not do any harm. Caution: When changing the settings of the imager/aimer module except for those described in the user guide the LED radiation may exceed the harmless area of class 1.
1.9.7
Safety Notes on the Imager with Laser Aimer If the type designation of your skeye.allegro contains option S6, your mobile terminal is equipped with an imager module with integrated laser aimer (e.g. HW 90250/V4S6), please observe the following notes: The laser beam is classified as a class 1 laser according to the following standard: IEC60825-1:2007. It is presumed that a short contact with this kind of laser beam does not do any harm, however, the following precautions are recommended: see chapter 1.9.5)
1.9.8
Safety Notes on Mobile Radio A mobile radio communication can be realised using an integrated module. If the type designation of your skeye.allegro contains option G7 or (in the future) G10, your mobile terminal is equipped with an GSM-/GPRS-/UMTS module (e.g. HW90250/V4G7). Please pay attention to the following safety notes. Radio devices (such as GSM) are subject to certain restrictions when used in proximity to electronic instruments: When being in an aircraft completely power off your skeye.allegro (see chapter 3.4.4). Using the skeye.allegro in an aircraft interferes with the electronic equipment on board and might be dangerous. The use is illegal. Non-compliance with this safety instructions may lead to prosecution. Switch off your skeye.allegro in hospitals or similar places to prevent an interference with medical devices. Switch off your skeye.allegro at places where you are advised to switch off your mobile phone. The unit may affect heart pacemakers. The Federal Office for Radiation Protection recommends a distance of no less than 20 cm between a mobile phone and a heart pacemaker to ensure no interference takes place. This recommendation is also in line with studies and recommendations issued by independent institutes. Users with heart pacemakers must ensure a distance of at least 20 cm between the skeye.allegro and the heart pacemaker. The unit may affect hearing aids. Interference may be noticed in close proximity to televisions, radios, PCs.
16
1.1 15.10.2014
INTRODUCTION Disposal 1.9.9
Safety Notes on Wireless LAN/Bluetooth A Wireless LAN- or Bluetooth-communication can be realised using an integrated module. If the type designation of your skeye.allegro contains option R12 or B4, your mobile terminal is equipped with an WLAN or Bluetooth module (e.g. HW90250/V4R12 or HW90250/V4B4). Please pay attention to the following safety notes. Radio facilities – as well as WLAN or Bluetooth - are subject to certain restrictions during use near electronical devices. In this connection please read the safety notes of the previous chapter. Wireless LAN data communication can be easily intercepted and recorded. Anyone who is operating a Wireless LAN card in the same subnet can “sniff out” and decrypt any sent data packets with the appropriate software. Secure your network against unauthorised intrusion into the WLAN. We recommend that you consult a specialist (e.g. a system house).
1.9.10 Safety Notes on Using GPS A GPS communication can only be realised with the skeye.allegro LS via integrated module. If the type designation of your skeye.allegro contains option E6 your mobile terminal is equipped with a GPS module (e.g. HW 90260/V4E6). Please observe the following note: Do not operate your navigation system while driving. Note that there may be different regulations for using such devices within vehicles in other countries. Please observe the respective regulations.
1.9.11 Safety Notes on Data Loss It is very much recommended that all important data be backed up as durable hardcopy. It is very much recommended to store all recorded data to flash disk and to regularly back up the data on an external medium. Given certain conditions, loss or modification of data can occur in practically any electronic storage system. Therefore, we do not accept any liability for loss of data or data being otherwise rendered unusable following incorrect use, repairs, faults, battery problems, software errors or for any other reason. We shall not be held liable either directly or indirectly for any financial loss or third party compensation claims which arise on foot of the use of this product and all and any of its functions, such as stolen credit card numbers, loss or modification of data, etc.
1.10
Disposal The mobile terminal is not intended for use in private households. The device must not be disposed of via a public waste disposal system. For disposal, return the device to the Höft & Wessel AG.
1.1 15.10.2014
17
THE SKEYE.ALLEGRO Variants
2.
The skeye.allegro
2.1
Variants The skeye.allegro is available in two variants: They only differ by their display format and the four additional keys under the display.
Fig. 2: skeye.allegro (HW 90250/V4)
Fig. 3: skeye.allegro LS (HW 90260/V4)
The displays shown in this documentation correspond to the portrait format of the skeye.allegro and the landscape format of the skeye.allegro LS.
18
1.1 15.10.2014
THE SKEYE.ALLEGRO Hardware Equipment 2.2
Hardware Equipment All variants incl. battery, 256 MB RAM, 1 GB Flash and Android (Gingerbread) 1 skeye.allegro WLAN 802.11a/b/g, Bluetooth and Laser scanner 2 skeye.allegro WLAN 802.11a/b/g, Bluetooth and 2D Imager 3 skeye.allegro WLAN 802.11a/b/g, Bluetooth and Laser scanner with cover 4 skeye.allegro UMTS, WLAN 802.11a/b/g, Bluetooth and Laser scanner 5 skeye.allegro LS WLAN 802.11a/b/g, Bluetooth and Laser scanner 6 skeye.allegro LS WLAN 802.11a/b/g and Laser scanner 7 skeye.allegro LS UMTS, WLAN 802.11a/b/g, Bluetooth, GPS and 2D Imager 8 skeye.allegro LS UMTS, WLAN 802.11a/b/g, Bluetooth, GPS and Laser scanner
2.3
Software Equipment Android 2.3.6 (Gingerbread)
2.4
Accessory
Battery HW 19200 with 1800 mAh Battery HW 19202 with 3300 mAh (extended capacity) Battery HW 19201 with 3600 mAh (doubled capacity) Battery recharger HW 16200 for 2 batteries; incl. power supply unit HW 14200 with EU cable 4-slot battery recharger HW 16250/4 (V2); incl. power supply unit HW 14204 Power supply unit HW 14200 Rubber protector for skeye.allegro LS Case with belt clip for skeye.allegro Case with belt clip for skeye.allegro LS Stylus RAM-Mount set for car cradle Hand strap Display protector skeye.allegro LS (1 pc) Cord for stylus
1.1 15.10.2014
19
THE SKEYE.ALLEGRO Communication Cradles 2.5
Communication Cradles
20
Communication cradle HW 50250 USB (Standard, V3C3C4) incl. power supply unit HW 14200 Communication cradle HW 50253 Ethernet (V1C2) incl. power supply unit HW 14200 4-slot Communication Cradle USB HW 50250/4 (V2) incl. power supply unit HW 14200 and USB cable 4-slot Communication Cradle Ethernet HW 50251/4 (V2) incl. power supply unit HW 14204 Car cradle HW 51250 incl. adaptor cable for GPS and power
1.1 15.10.2014
THE SKEYE.ALLEGRO Views 2.6
Views
2.6.1
Front View
LED*
Display
Scanner button
Stylus
Scanner button Power-onbutton Cursor keys
Keypad
System interface Fig. 4: Front view
*Definition: The red LED indicates the battery charging status (shines permanently while loading, flashes when the battery is fully charged). The green LED shines respectively flashes when the system starts. In addition, the LEDs can be controlled by applications; e g. green = barcode read successful (BarcodeConfig program).
1.1 15.10.2014
21
THE SKEYE.ALLEGRO Views 2.6.2
Rear View
Strap lock
Stylus
Loud speaker
Strap
Battery
Fig. 5: Rear view
22
1.1 15.10.2014
THE SKEYE.ALLEGRO Keyboard 2.7
Keyboard The key assignment in Android is as follows:
Cursor keys
Power on button and
Cursor keys
Power on button and
Fig. 6: skeye.allegro (HW 90250/V4)
Fig. 7: skeye.allegro LS (HW 90260/V4)
Home
Back
Default desktop Long pressing: calls the menu of the app most recently started. See also the note in chapter 4.3.1. Scrolls back to previous page
Menu
Context-specific
Switching on Trigger keys
Switching On/Off Long pressing: Calls the power service menu Can e.g. be used for scanning
Function keys
Freely assignable function keys
1.1 15.10.2014
23
TAKING INTO OPERATION Using the SD Card
3.
Taking into Operation The mobile terminal comes with a separate battery. Prior to inserting the battery the SIM card and the SD card (if available for this variant) should be inserted and the battery should be fully charged (see chapter 3.3 ff.).
3.1
Using the SD Card At the front of the mobile terminal there is an extension slot for SD memory cards. This slot is protected by a removable cover. The protection class IP65 is only guaranteed if the protective cover is correctly mounted.
1. Remove the screws at the protective cover.
2. Insert the SD card in the upper slot (rounded edge) as shown in the figure (push-push function). 3. Screw down protective cover.
Fig. 8: Insert SD card
24
1.1 15.10.2014
TAKING INTO OPERATION Using the SIM Card* 3.2
Using the SIM Card* *Only for devices with integrated radio module.
If your skeye.allegro is equipped with a mobile radio module it also has a slot for the required card. This slot can be found on the front side near the SD card slot. Remove the protective cover prior to removing the SIM card. Protection class IP 65 is only guaranteed if the protective cover is correctly mounted.
There is an additional yellow cover in front of the SIM card slot which can be mounted using special screws. During installation, which sometimes requires the replacement of the SD card, this additional cover makes it more difficult to access the SIM card.
Only with a properly mounted inner protective cover, the SIM card is held in the slot in case of high impact load.
1. Remove the screws at the protective cover.
2. Remove the special screws of the inner protective cover.
3. With the contacts facing downwards, insert the SIM card into the lower slot (contacts facing downwards, rounded edge on the left) as shown in the figure (push-push function). 4. Screw together inner and outer protective cover. Fig. 9: Insert SIM card
1.1 15.10.2014
25
TAKING INTO OPERATION Battery 3.3
Battery
3.3.1
Inserting the Battery There is only one way to insert the battery. 1. Rotate the upper clamp of the strap by 90° to the right or left to loosen it.
2. Insert the new battery with the rounded side facing to the front and press it until it audibly engages.
Fig. 10: Inserting the battery
3. Re-insert the upper clamp of the strap. Prior to initial operation the battery should be charged completely. To do so, insert the mobile terminal including battery into the communication cradle or the battery recharger (connected to power) or the car cradle. See chapter 3.3.3. To remove the battery move the slider to the top and remove the battery. See next chapter.
26
1.1 15.10.2014
TAKING INTO OPERATION Battery 3.3.2
Replacing the Battery 1. Back up your data before changing the battery (depends on the application). 2. Switch off the device before changing the battery.
1. Rotate the upper clamp of the strap by 90° to the right or left to loosen it.
2. Move the slider to the top and remove the battery.
3. Insert the new battery and move the slider downwards. The battery audibly locks into place.
Fig. 11: Changing the battery
1. Re-insert the upper clamp of the strap.
1.1 15.10.2014
27
TAKING INTO OPERATION Battery 3.3.3
Charging the Battery The battery in the skeye.allegro is automatically recharged if the skeye.allegro is in the battery recharger or communication cradle (with connected power supply unit), in the car cradle On the Android Status Bar (see Fig. 15) one of the following symbols displays: The storage battery is discharged. The mobile terminal switches off as soon as possible. The storage battery is low and must be charged. The storage battery capacity is very low. The storage battery should be charged as soon as possible. Displays the storage battery capacity (several levels). The storage battery recharges. Fig. 12: Battery symbols
Always recharge the battery in time. If the battery is discharged, data loss may occur.
28
1.1 15.10.2014
TAKING INTO OPERATION Switching On/Switching Off the skeye.allegro 3.4
Switching On/Switching Off the skeye.allegro
3.4.1
Switching On The mobile terminal is switched-on by pressing the left button below.
Power-on button
Fig. 13: Power-on button
3.4.2
Switching Off There are three ways to switch off your skeye.allegro:
3.4.3
Suspend mode Automatic Standby (AutoOff) Complete Power Off
Suspend Mode Shortly press the Power On button.
3.4.4
Automatic Standby (Display Timeout) Here, you can define the time after which the mobile terminal switches to Suspend mode. On the Home screen, press the "Menu" button of the skeye.allegro. Tap [Settings].
1.1 15.10.2014
29
TAKING INTO OPERATION Switching On/Switching Off the skeye.allegro Tap "Display".
Tap the arrow next to "Screen timeout". Set the interval to 1, 2, 10 or 30 min.
Fig. 14: Automatic suspend
If the mobile terminal is connected to charging current, it will not switch to suspend mode. Only the display will be dimmed after a defined period of time.
30
1.1 15.10.2014
TAKING INTO OPERATION Switching On/Switching Off the skeye.allegro 3.4.5
Complete Power Off Completely power off your skeye.allegro in the following situations:
If you do not operate your skeye.allegro for a longer period of time (battery saving) When entering an aircraft. In explosive areas
Performing a complete power off: 1. Keep the Power on key pressed for a while. 2. Then, select "Power off" (or Airplane Mode, if you are on an airplane) 3. Wait until the display is off. 4. Remove the storage battery as described in chapter 3.3.2. This will shut down all running processes. If you do not remove the storage battery, the mobile terminal restarts.
If the storage battery is removed while a process is still running and no complete power off is performed as described above, a data loss may occur. Thus, proceed as described in chapter 3.4.5. If the battery is not inserted, the tightness for the mobile terminal according to IP65 is no longer ensured. Store the mobile terminal in a dry environment.
1.1 15.10.2014
31
INITIAL STEPS Operating the skeye.allegro with the Stylus
4.
Initial Steps 1. Insert the battery (see chapter 3.3.1) 2. Press
to switch on the skeye.allegro.
3. Take out the stylus (see Fig. 5: Rear view)
4.1
Operating the skeye.allegro with the Stylus The stylus functions as a computer mouse. It is used to navigate on the screen and to select elements. Remove the stylus from its clamp and put it back when you do not need it. Operate the touch screen only with the stylus supplied or your finger.
4.2
Tapping Tap the screen with the stylus once to open an app.
Tap and hold Tap on an element and keep the stylus pressed onto the screen e.g. to move an app to the home screen.
Using the Navigation Key With the navigation key you can move to the top, to the bottom right, and to the bottom left in the menu. This function is especially useful when operating the device with one hand only.
To move the cursor to a certain direction simply press the corresponding side of the key. To confirm the selection press the key in the middle [OK].
32
1.1 15.10.2014
INITIAL STEPS Android – Basics 4.3
Android – Basics This mobile terminal uses Android 2.3.6 (Gingerbread). Copy deadline, subject to changes. In case of problems refer to the corresponding Android documentation. The documentation can be found here: https://support.google.com/nexus/s/answer/182077?hl=en-GB
4.3.1
Home Screen Having started Android or having pressed the Home key on the mobile terminal a screen similar to the following displays:
Android Status Bar
e.g. time, field strength, storage battery status, Internet connection, WLAN, and synchronization
All Apps
Internet connection
Phone functions Fig. 15: Home Screen
1.1 15.10.2014
33
INITIAL STEPS Android – Basics 4.3.2
Basic Settings The settings are called as follows: On the Home screen, press the "Menu" button of the skeye.allegro.
Tap the [Settings] button.
34
1.1 15.10.2014
INITIAL STEPS Android – Basics The settings menu is displayed:
Fig. 16: Settings (Example)
4.3.3
Symbols on the Android Status Bar The following list contains an explanation of the symbols which can usually be found up on the Android Status Bar. Symbol
Name Mobile phone network
Description Signal strength of the mobile phone network.
Bluetooth
Connected to a Bluetooth device.
USB
Device is connected to a PC via USB cable.
GPS
Reception of standard data via GPS.
Sync
Data is synchronized
WLAN
WLAN is activated.
System warning
4.3.4
Showing/Hiding the Keyboard The screen keyboard displays automatically when a field requiring entries is selected. The keyboard can be hidden by pressing the [Esc] key.
1.1 15.10.2014
35
INITIAL STEPS Android – Basics 4.3.4.1 Setting the Brightness On the Home screen, press the "Menu" button of the skeye.allegro. Tap [Settings].
Tap "Display".
Tap the arrow next to "Brightness".
36
1.1 15.10.2014
INITIAL STEPS Android – Basics In this window, adjust the brightness of the backlight with the slider. Tap [OK].
Fig. 17: Setting the brightness
1.1 15.10.2014
37
INITIAL STEPS Android – Basics 4.3.4.2
Setting the Properties of the Input Panel (Keyboard) On the Home screen, press the "Menu" button of the skeye.allegro. Tap [Settings].
Tap "Language & keyboard".
Tap "Android keyboard".
38
1.1 15.10.2014
INITIAL STEPS Android – Basics Select the required settings here.
Fig. 18: Keyboard settings
1.1 15.10.2014
39
FURTHER FUNCTIONS AND SETTINGS Scanner Operation
5.
Further Functions and Settings
5.1
Scanner Operation To test the scanner function call the "BarcodeScanner" ScanTool ( see chapter 5.1.1). The program automatically adjusts to the respective module (scanner or imager). Hold the skeye.allegro safely and slightly tilted so that it faces towards the barcode to be scanned. Depending on the settings a successfully scanned barcode can be confirmed with a beep or vibration. The distance should be 10 cm (see figure).
Fig. 19: Mobile terminal, scanning position
Apart from the resolution of the barcode and the distance, other factors also influence a reliable reading of the barcode: e.g. print and paper quality, scanner and software settings, barcode type and thus the width of the barcode, the amount of data in the barcode and so on.
40
1.1 15.10.2014
FURTHER FUNCTIONS AND SETTINGS Scanner Operation The following figures show the positions for directing the scanner beam onto the bar codes. Imager:
.. ..
.. ..
..
..
Laser scanner:
. ..
.. ...
... ..
The following figures show incorrect scanner positions. With these positions it is hardly possible to scan successfully. Imager:
.. ..
.. .
..
..
.. ..
.. ..
..
..
Laser scanner:
Scan Keys For scanning you can use the yellow keys.
Scan Key Scan Key
Fig. 20: Scan key
1.1 15.10.2014
41
FURTHER FUNCTIONS AND SETTINGS Scanner Operation 5.1.1
BarcodeScanner (skeye) BarcodeScanner offers the following functions:
The scanner can be triggered via the scan keys. The Scanner is configured. The program works like a keyboard wedge: Like a text entry, the scanned barcodes are e.g. output in a text field.
5.1.1.1 Scanning Tap "All apps" screen.
on the skeye.allegro Home
Tap "BarcodeScanner".
42
1.1 15.10.2014
FURTHER FUNCTIONS AND SETTINGS Scanner Operation Scan a barcode by first pressing the left yellow Scan key of the skeye.allegro. A red dot that serves as aiming aid is displayed. Point the red dot towards the barcode to be scanned. On the bottom in the middle of the screen tap "Scan" or press the right yellow Scan key of the skeye.allegro.
A successfully scanned barcode is acknowledged by two beeps (setting-dependent)
Fig. 21: Scan
1.1 15.10.2014
43
FURTHER FUNCTIONS AND SETTINGS Scanner Operation 5.1.1.2 Settings Tap "Settings" at the bottom right of the screen.
Different settings can be made here. Encodings: use all
Fig. 22: Scan settings
44
1.1 15.10.2014
FURTHER FUNCTIONS AND SETTINGS System Information (SysInfo) 5.2
System Information (SysInfo) Tap "All apps" skeye.allegro.
on the Home screen of the
Tap "Sysinfo".
1.1 15.10.2014
45
FURTHER FUNCTIONS AND SETTINGS System Information (SysInfo) All important system information is displayed here.
Fig. 23: SysInfo
The Versions tab displays information on operating system, serial number, and battery parameters.
The Memory tab displays information on physical memories, drives and data memories.
Operating system and system programs (such as an Update tool) can read the hardware configuration of the devices from the HWI-Block (Hardware Information Block). .
The GSI-Block tab (device specific information block) contains device specific information. .
The Mac Adresses tab informs on the mac addresses of the radio modules. Tap [Esc] to close the window.
46
1.1 15.10.2014
FURTHER FUNCTIONS AND SETTINGS System Information (SysInfo) 5.2.1
Creating a SysInfo Report File When calling the system information a report file can be created containing the same information as SysInfo. 1. Press the Menu button on the skeye.allegro when you are in SysInfo (see previous chapter).
A "Pref" button displays at the bottom of the screen.
2. Tap [Pref].
3. Tap [Report].
1.1 15.10.2014
47
FURTHER FUNCTIONS AND SETTINGS System Information (SysInfo)
A message displays for a few seconds informing the user that a report file was created and stored to the mnt/tmp directory.
4. Change to the mentioned directory. See next chapter.
Fig. 24: System information | Create report file
5.2.2
Calling the SysInfo Report File 1. Tap "AndExplorer".
48
1.1 15.10.2014
FURTHER FUNCTIONS AND SETTINGS System Information (SysInfo) 2. Tap [root].
3. Tap the /mnt directory.
4. Tap the /tmp directory.
1.1 15.10.2014
49
FURTHER FUNCTIONS AND SETTINGS System Information (SysInfo) Here you see the "report.txt".
5. Tap the "Report.txt" and keep the stylus pressed. The file will be selected and marked with a green hook. 6. Press the menu button skeye.allegro.
on the
The following context menu appears. It can be used for the following tasks: Rename Delete Create folder Copy/Paste Sort More o Details o Send o Refresh o Select all files o Deselect all files o Clear selection Fig. 25: System information | Call report file
Please include the report file in case of a support request.
50
1.1 15.10.2014
FURTHER FUNCTIONS AND SETTINGS Sound 5.3
Sound On the Home screen, press the "Menu" button of the skeye.allegro. Tap [Settings].
Tap "Sound".
•
Silent mode: Silences all sounds except for the alarm sound
•
Vibrate: Different options for setting the vibration.
•
Volume: Volume of the different sounds (see the next but one figure)
•
Phone ringtone: Settings the ring tones for incomming calls
1.1 15.10.2014
51
FURTHER FUNCTIONS AND SETTINGS Sound •
Notification ringtone: Settings the ring tones for call waiting tones
•
Audible touch tones: Play tones when using the dial pad
•
Audible selection: Play sound when making an on-screen selection
•
Screen lock sounds: Play sounds when locking or unlocking the screen
•
Haptic feedback: Vibrate when pressing soft keys and other interactions
Volume: Use the sliders to set the volume for ring tones, Media and alarm.
Fig. 26: Sound
52
1.1 15.10.2014
FURTHER FUNCTIONS AND SETTINGS Switching the Radio Modules On and Off 5.4
Switching the Radio Modules On and Off The radio modules are switched on and off here: On the Home screen, press the "Menu" button of the skeye.allegro. Tap [Settings].
Tap "Wireless & networks".
WiFi:
See chapter 6.1, page 55.
Mobile radio:
See chapter 6.2, page 57.
Bluetooth:
See chapter 6.3, page 59.
Fig. 27: Switching the Radio Modules On and Off
1.1 15.10.2014
53
FURTHER FUNCTIONS AND SETTINGS Updating the Operating System 5.5
Updating the Operating System 1. Request an update from the support center. The address can be found on the last page. 2. Copy the update to an SD card. 3. Insert the SD card into the skeye.allegro ( see chapter 3.1, page 24). 4. Remove the battery and execute a hardware reset ( see chapter 9.1, page 75). 5. Re-insert the battery. 6. Repeatedly press the "1" key until the Linux penguin and a first boot text displays. Then stop pressing key "1". 7. Several screens appear informing you of the update status.
If you update the operating system all data in the memory of the skeye.allegro will be deleted. Prior to an update back up all data to an external memory.
Please enquire for current operating system version.
54
1.1 15.10.2014
RADIO MODULES Wireless LAN
6.
Radio Modules
6.1
Wireless LAN Only for devices with integrated WLAN module.
If the type designation of your skeye.allegro contains option R12, your mobile terminal is equipped with a WLAN module 802.11a/b/g (HW 90250/V4R12). 1. On the Home screen, press the "Menu" button of the skeye.allegro. 2. Tap [Settings].
3. Tap "Wireless & networks".
4. Activate the "Wi-Fi" check box. 5. Tap "Wi-Fi settings".
1.1 15.10.2014
55
RADIO MODULES Wireless LAN
6. Select a network.
A lock symbol () indicates an encrypted network. A password is required.
7. You may also select "Add Wi-Fi network".
Add Wi-Fi network: 8. Enter the network SSID. 9. Below "Security" set the security level (Open, WEP, WPA/WPA" PSK, 802.1x EAP). 10. Then, tap [Save].
Fig. 28: WLAN
Be sure to protect your Wireless LAN network. We recommend that you consult a specialist. Further information on the configuration and status query of the WLAN Summit modules can be found here: http://www.summitdata.com/documentation.html
56
1.1 15.10.2014
RADIO MODULES Mobile Radio 6.2
Mobile Radio Only for devices with integrated radio module.
If the type designation of your skeye.allegro contains option G7 or G10, your mobile terminal supports the use of a radio module (HW 90260/V4G7). First insert the SIM card of your provider into the mobile terminal. See also chap. 3.2, page 25. When establishing a mobile radio connection ensure your provider offers a time tariff. First, please request the connection settings and the APN (Access Point Name) from your provider.
1. On the Home screen, press the "Menu" button of the skeye.allegro. 2. Tap [Settings].
3. Tap "Wireless & networks".
1.1 15.10.2014
57
RADIO MODULES Mobile Radio 4. Scroll-down and select "Mobile networks".
5. Different settings can be made here. 6. Below "Access Point Names" enter the APN requested from your provider.
Fig. 29: Mobile radio
Please note:
58
Establishing a mobile radio connection is with costs. For more information please contact your provider.
By default, Android uses GSM connections. However, if you are already logged into a WLAN, a GSM based data connection will be terminated as WLAN usually provides faster and cheaper connections.
1.1 15.10.2014
RADIO MODULES Bluetooth 6.3
Bluetooth Only for devices with integrated Bluetooth module.
If the type designation of your skeye.allegro contains option B4, your mobile terminal is equipped with a Bluetooth module (e.g. HW 90250/V4B4). 1. On the Home screen, press the "Menu" button of the skeye.allegro. 2. Tap [Settings].
3. Tap "Wireless & networks".
4. Activate the "Bluetooth" check box. 5. Tap "Bluetooth settings".
1.1 15.10.2014
59
RADIO MODULES GPS* 6. Different settings can be made here.
Fig. 30: Bluetooth
6.4
GPS* * Only for skeye.allegro LS If the type designation of your skeye.allegro contains option E6, your mobile terminal is equipped with a GPS module (e.g. HW 90260/V4E6). The COM port used in the mobile terminal is COM2. Baud rate: 9.600. Please note: GPS (Global Positioning System) is provided by the government of the USA. Thus, the accuracy of the system can be influenced by the USA under certain conditions (war zone or restricted area). GPS performance gets influenced if the area covered by satellites is near high buildings, in a tunnel or below roofs. The navigation software is available on request.
60
1.1 15.10.2014
COMMUNICATION CRADLES Communication Cradle HW 50250 and 50253 - View
7.
Communication Cradles
7.1
Communication Cradle HW 50250 and 50253 - View Slot for mobile terminal with battery
Slot for spare battery
LEDs*
Fig. 31: Communication cradle
The red LED* shows the battery charging status. (shines permanently during charging process, flashes when the battery is fully charged)
*HW 50250: green/not used/yellow HW 50253: green/yellow/yellow (left yellow LED for data communication display)
For more information on the LEDs please refer to the user guide of the respective communication cradle.
1.1 15.10.2014
61
COMMUNICATION CRADLES Connections of HW 50250 (USB, Standard) 7.2
Connections of HW 50250 (USB, Standard) /V3C3C4
Several connections can be found at the rear side of the communication cradle.
USB-Device to connect to the desktop PC using ActiveSync
Power supply: Power supply unit connection HW 14200
Serial interface
Fig. 32: Communication cradle HW 50250, connections
7.3
Connections of HW 50253 (Ethernet) /V1C2
Ethernet (RJ 45)
Power supply Fig. 33: Communication cradle HW 50253, connections
62
1.1 15.10.2014
COMMUNICATION CRADLES Technical Data HW 50250/HW 50253 7.4
Technical Data HW 50250/HW 50253 Casing:
Shock resistant plastic, self-extinguishing according to UL94V-0 Bottom plate made from galvanised sheet steel Back made from stainless steel
Slots:
HW 50250 und HW 50253: One slot for the mobile terminal including battery. The following interfaces are used: - mobile terminal power supply, 9 V +/-5 %, 2.0 A - The USB OTG interface of the mobile terminal is either connected to the USB A slot (host mode) or the USB B slot (device) of the communication cradle (control via the respective terminal). Charging slot for HW 19200 or HW 19201 battery Only HW 50253:
Ports & Connectors
The USB host of the mobile terminal communicates with the "USB to Ethernet" converter in the communication cradle. Used for data transmission from or to the connected network.
Power supply: - Connection for HW 14200/V2 power supply, DC voltage input Mini DC Power Jack 1,3 mm, 9 V / 2.5 A Data interfaces: -
-
Displays:
USB (only HW 50250)
Ethernet (instead of USB) (only HW 50253)
USB-A, Full Speed USB-B, Full Speed Caution: Only one of the interfaces can be active at a time! 10/100Base-T (10/100 MBit/s) Ethernet jack, 8-pole (8P8C) modular jack
HW 50250 und HW 50253:
1 red LED for spare battery charging process
HW 50250: LEDs on the front panel: green – yellow (not used) – yellow signal communication cradle operating status HW 50253: Battery charging:
LEDs on the front panel: green – yellow – yellow signal communication cradle operating status 2 LEDs integrated into the Ethernet jack (currently not used) In accordance with manufacturer's instructions Charging in mobile terminal: controlled by mobile terminal charging electronics Charging in spare battery charging slot: controlled by USB communication cradle charging electronics When inserted battery is recognised, first charging using constant current charging, subsequently switches over to constant voltage charging. Charging start with reduced charging current for rechargeable
1.1 15.10.2014
63
COMMUNICATION CRADLES Technical Data HW 50250/HW 50253
64
batteries with low voltage. Automatic switch-off of charging process when battery fully charged. Automatic switch-off if battery overheats. Constant current charging: approx. 900 mA Reduced charging current: approx. 180 mA Switch-off charging current: approx. 100 mA Charging end voltage: 4,2 V +/- 1% Battery temperature at the start charging process: 0 °C to +40 °C Charging time: about 2.5 h (HW 19200) or about 5 h (battery HW 19201/HW 19202) Timeout: about 5 h (battery HW 19200) or about 10 h (battery HW 19201/HW 19202)
Ambient conditions:
Rules and Standards:
CE conformity ElektroG and RoHs conformity
Dimensions:
about 180 mm x 110 mm x 95 mm (L x W x H)
Weight:
about 700 g
1.1 15.10.2014
Operate only indoors Ensure good ventilation is available Operating temperature: limit values: 0 °C to +40 °C, recommended range: 10 °C to +30 °C, Storage temperature: -20 °C to +60 °C Humidity: up to 85 % (non-condensing)
COMMUNICATION CRADLES Connecting the Communication Cradle 7.5
Connecting the Communication Cradle
7.5.1
HW 50250
e.g. USB stick
PC
Power supply unit USB cable Fig. 34: Connection ccommunication cradle PC
1. Establish a connection between the communication cradle and the PC at an USB port. 2. Connect the power supply unit to the communication cradle. 3. Insert the mains plug into the socket.
1.1 15.10.2014
65
COMMUNICATION CRADLES Connecting the Communication Cradle 7.5.2
HW 50253
Power supply unit Ethernet cable Fig. 35: Connection ccommunication cradle Ethernet
1. Establish a connection between the communication cradle and your network at an ethernet port. 2. Connect the power supply unit to the communication cradle. 3. Insert the mains plug into the socket.
Further communication cradles: Please enquire for the separate user guides of the communication cradles.
66
1.1 15.10.2014
COMMUNICATION CRADLES LED Function Display 7.6
LED Function Display
7.6.1
HW 50250 The USB communication cradle HW 50250/V3C3C4 supports the USB connection of a mobile terminal either on the USB host slot (USB-A) or on the USB device slot (USB-B). Thus, a mobile terminal can either serve as USB host or as USB device. If the function is changed to "Host" the yellow LED on the right side shines. Green (Front left)
Not used (Front middle)
Yellow (Front right)
Red (Chargi ng control)
Definition
Off
Off
Off
Off
Communication cradle is not ready. (no power)
On
Off
Off
X
Communication cradle is ready. (Power on). Similar display if a mobile terminal with activated USB device is inserted.
On
Off
On
X
Mobile terminal with activated USB host is inserted in the communication cradle.
On
Off
X
Off
No spare battery in place or spare battery not detected.
On
Off
X
On
Spare battery detected, spare battery is being charged.
On
Off
X
Flashes
The battery temperature is too high or too low after it has been placed in the charger, once the correct temperature has been reached, charging will start.
1.5s On; 0.1s Off On
On
On
Off
Off
Off
X
Fast flashing
X
1.55s Off; 0.05s On Flashes
X
0.2s Off; 0.2s On Flashes 0.2s Off; 0.2s On; every 3 periods 1 flash impulse is missing
Charging is complete.
Error, charging was terminated: Spare battery voltage is still too low after a charging time of approx. 90 minutes. Spare battery is defective Error, charging was terminated: The spare battery temperature got too high or low during charging. Cause: The docking station was exposed to adverse temperatures while charging, for instance it was exposed to direct sunlight or situated near an open window in winter. Once the adverse conditions have been rectified, the charging process can be restarted by taking out the battery and putting it back in. Spare battery is defective
Tab. 1: HW 50250/V3C3C4, LED states, X= may have any state (on, off, flashing)
1.1 15.10.2014
67
COMMUNICATION CRADLES LED Function Display 7.6.2
HW 50253 Green (front left)
Yellow (front middle)
Yellow (front right)
Red (chargi ng control)
Meaning
Off
Off
Off
Off
Docking station is not ready (no power).
On
Off
Off
X
Communication cradle is ready. (Power on). Similar display if a mobile terminal with activated USB device is inserted.
On
Off
On
X
Mobile terminal with activated USB host is inserted in the communication cradle.
On
X
X
Off
No spare battery in place or spare battery not detected.
On
X
X
On
Spare battery detected, spare battery is being charged.
On
X
X
Flashes
The battery temperature is too high or too low after it has been placed in the charger, once the correct temperature has been reached, charging will start.
1,5s On; 0,1s Off On
On
On
X
X
X
X
Fast flashing
X
1,55s Off; 0,05s On Flashes
X
0,2s Off; 0,2s On Flashes 0.2s Off; 0.2s On; every 3 periods 1 flash impulse is missing
On
On
On
X
On
Flickers
On
X
Charging is complete..
Error, charging was terminated: Spare battery voltage is still too low after a charging time of approx. 90 minutes. Spare battery is defective. Error, charging was terminated: The spare battery temperature got too high or low during charging. Cause: The docking station was exposed to adverse temperatures while charging, for instance it was exposed to direct sunlight or situated near an open window in winter. Once the adverse conditions have been rectified, the charging process can be restarted by taking out the battery and putting it back in. Spare battery is defective. Mobile terminal with activated USB host is inserted and an Ethernet cable is connected (link available). Mobile terminal inserted, data are transferred via Ethernet.
Tabelle 2: HW 50253/V1C2, LED states, X= may have any state (on, off, flashing)
68
1.1 15.10.2014
COMMUNICATION CRADLES Charging the Battery in the Communication Cradle 7.7
Charging the Battery in the Communication Cradle The communication cradle provides the charging and operating current for the inserted mobile terminal and includes a charger for a spare battery. Charge battery
in the mobile terminal: If you cannot switch on the mobile terminal although the battery is inserted or if the mobile terminal displays a message stating that the battery voltage is low, charge the battery. A message on the mobile terminals screen indicates that the battery is in need of charging. To charge the battery, place the mobile terminal (including battery) in the communication cradle (connected to power). If the LED on the mobile terminal is red, the mobile terminal has been placed correctly in the communication cradle. In addition, the charging process is indicated on the mobile terminals screen. Spare battery: If you wish to charge a spare battery, place the battery in the communication cradle (connected to power). If the red LED in front of the spare battery compartment is on, the battery has been inserted correctly in the communication cradle and will be charged.
Charging completed
in the mobile terminal: If the red charging control LED of the mobile terminal changes from permanent shining to flashing, the battery is fully recharged. The mobile terminal is ready to use. Spare battery: If the red LED in front of the spare battery compartment is just flashing, the spare battery is fully charged
Charging time
A completely discharged battery will be recharged in approx. 2.5 to 3 hours. If the battery is not fully discharged, the recharging period is shortened accordingly. For a HW 19201 battery, the charging time doubles.
The red charging control LED at the mobile terminal and communication cradle may
be off shine permanently or flash.
It may also indicate possible failures by
blinking
When flashing, the LED is activated only for a short time. When blinking, the on and off times of the LED are nearly equal. To differ between blinking and flashing, a closer look at the LED is required. However, this is only necessary when the charging process does not start immediately, i.e. the charging control LED does not shine permanently or when the charging process takes remarkably long.
1.1 15.10.2014
69
TECHNICAL DATA Charging the Battery in the Communication Cradle
8.
Technical Data Casing:
Upper shell, lower shell and Interface cap in impact-resistant plastic, self-extinguishing in accordance with UL94V-0 Housing protection IP 65
Processor:
Marvell PXA 320 806 MHz
Memory:
1 GB Flash 256 MB DDR-RAM
Display: Type: Size / Resolution: Amount of colours:
QVGA colour TFT with touch screen skeye.allegro: 2,8" / 240 x 320 pixels skeye.allegro LS: 3,5" / 320 x 240 pixels 65,536 Colours
Touch: Technology: Battery:
Analogue Resistive exchangeable Lithium-Ion battery, Standard-Akku: 3.7 V/1800 mAh Erweiterter Akku: 3.7 V/3300 mAh Doppel-Akku: 3.7 V/3600 mAh
Connectors & Ports: Extension slot for SD memory cards SIM card for integrated GSM module (optional) System connectors for - Charging power connection - USB device - Serial communication 2-Wire RS232 port with V24 levels - Barcode reader - Headset
70
Temperature range:
Working: Storage: Relative humidity:
Dimensions:
W 54/73 mm, H 26/47 mm, L 201 mm (skeye.allegro) W 54/116 mm, H 26/47 mm, L 201 mm (skeye.allegro LS)
Weight:
About 350 or 400 g (incl. battery)
Rules and Standard:
CE conformity ElektroG and RoHs conformity
1.1 15.10.2014
-10 °C - +50 °C -20 °C - +60 °C 10-90%, not condensing
TECHNICAL DATA Modules 8.1
Modules The mobile terminal can be equipped with different optional modules. The equipment is indicated by a letter code (e.g. R12). If one of the optional modules has been integrated, the relevant letter code can be found on the serial number sticker.. Having removed the battery (see chapter 3.3) the serial number sticker becomes visible. Example: HW 90250/V4B4S9 or HW 90260/V4E6S7... WLAN:
Letter code: R12 Integrated WLAN module IEEE 802.11a/b/g (11/54 Mbit/s) Dual Band 2,4 GHz/5 GHz Integrated antenna diversity
Bluetooth:
Letter code: B4 (B = Bluetooth) Integrated Bluetooth module Class 2 According to Bluetooth specification V2.0 + EDR Integrated antenna
Mobile Radio:
Letter code: G7, G10 (G = GSM) G7 GSM/GPRS/EGPRS(EDGE): 900 / 1800 MHz GPRS Multislot Class 12, EGPRS Multislot Class 12 Integrated antenna G10
GPS: skeye.allegro LS only
(R = Radio)
UMTS(WCDMA)/HSDPA: 900 / 2100 MHz UMTS max. 384 kbps, HSDPA max. 3,6 Mbps (Cat 12, 5, 6) GSM/GPRS/EGPRS(EDGE): 900 / 1800 MHz GPRS Multislot Class 10, EGPRS Multislot Class 12 Integrated antenna
Letter code: E6 Receiver type: Time To First Fix (TTFF): Cold start (autonomous): Hot start (autonomous): Sensitivity: Tracking: Cold start (autonomous): Galileo ready
(E = Receiver) 50 channels >2 Mio. Correlators 29 s <1s -162 dBm -147 dBm
1.1 15.10.2014
71
TECHNICAL DATA Modules
Scanner/ Imager: Scanner Letter code: S5 Barcode scanner of laser class 2 See chap. 8.1.1
(S = Scanner)
Letter code: S9 Barcode scanner of laser class 2 See chap. 8.1.1 Imager Letter code: S6 2-D imager: Aiming device: Laser frame – the barcode can be targeted using a frame with a cross in the middle. See chap. 8.1.2 Letter code: S7 2-D imager: Aiming device: Green LED – the barcode can be targeted using a green LED bar. See chap. 8.1.2
Protection class IP65 of the mobile terminal is only ensured if the battery is inserted and the protective cover at the top end of the device is mounted.
72
1.1 15.10.2014
TECHNICAL DATA Modules 8.1.1
Barcode Scanner 1D scanner (Option S5, S9)
Barcode scanner (laser class 2) Currently supported barcode types (depends on the software used, e.g. BarcodeConfig): Codabar Code 39 Code 93 Code 128 Databar (RSS Exp) Databar Limited Databar Expanded EAN 8 EAN 13 EAN 128 2 of 5 Industry 2 of 5 Interleaved Plessey Code UPC-A UPC-E
Reading distance 1D scanner
The following figure displays the reading distance of the scanner with respect to the line spacing of the barcode to be scanned. Term definition: mil Module width: Specifies the widths of the individual barcode elements. A \'mil\' is the thousandth part of an inch (0.001") and thus 0.0254 mm. If a min. width of 6.8 is specified, each barcode element (bar or space) must have a minimum width of 0.173 mm. Depth of Depth of field: Specifies the max. distance of the Field scanner's exit window to the barcode at which barcodes can be read. Note: Typical performance at 73.4 F (23 C) on high quality symbolss
4 mil
1.50
5.50
5 mil
1.80 2.20
8.00 7.5 mil
13.00
10 mil
2.20
18.00
100% UPC
2.20
24.00
15 mil
2.20
28.00
20 mil
2.50
29.00
40 mil
*
Inch 0 cm 0
33.00
55 mil
5 12,7
10 25,4
15 38,1
*Minimum distance determined by symbol length and scan angle
42.00
20 50,8
25 63,5
30 76,2
35 88,9
40 101,6
Depth of Field
1.1 15.10.2014
73
TECHNICAL DATA Modules 8.1.2
Imager 2D Imager (Option S6 or S7)
CMOS imager for 1D and 2D barcodes Resolution: 640 x 480 pixels, 256 greyscale To record common barcodes and 2D barcodes Currently supported barcode types: (depends on the software used, e.g. HWImagerTool) Implemented 1D barcodes:
Planet Code Plessey Code PosiCode Postnet Code Straight 2 of 5 Straight 2 of 5 IATA Telepen Code Trioptic Code UPC-A UPC-E
Australian Post British Post Canadian Post China Post Codabar Code 11 Code 16K Code 39 Code 49 Code 93 Code 128 Codablock Databar (RSS Exp) Dutch Post EAN 8 EAN 13 Interleaved 2 of 5 ISBT 128 Japanes Post Korean Post Matrix 2 of 5 MSI OCR Reading distance 2D imager
1D barcodes - continued:
Implemented 2D barcodes: Aztec Aztec Mesa Composite DataMatrix Maxi Code Micro PDf PDF 417 QR Code TLC39 Code
This figure shows the dependency between reading direction and image size. 30 20 10
19,0 12,9
6,5
4,8 9,7 14,5
Measurements in cm
74
1.1 15.10.2014
TROUBLESHOOTING Reset via Hardware
9.
Troubleshooting In case there is no problem solution in this chapter
9.1
send an e-mail to:
[email protected] or contact our service line. The phone numbers can be found ad the end of this document.
Reset via Hardware If the touch screen does not react or if you cannot switch on the device, press the reset button in the battery compartment of the device. To initiate a reset, proceed as follows: 1. Remove the battery. 2. Press the reset key located underneath the battery. Press the reset key carefully with low expenditure of force. ok
Fig. 36: skeye.allegro, reset
You can do this using an opened paper clip or similar. 3. Insert the battery. The skeye.allegro switches on automatically.
Note: After a hardware reset, all data and settings in RAM are deleted from your mobile terminal. Data and settings in FLASH are not deleted.
1.1 15.10.2014
75
TROUBLESHOOTING Resetting the Device to Factory Settings 9.2
Resetting the Device to Factory Settings To reset the device to factory settings proceed as follows: Caution: After a factory reset all data and settings are lost!
On the Home screen, press the "Menu" button of the skeye.allegro. Tap [Settings].
Tap "Privacy".
Tap "Factory data reset". All data on the device will be deleted! Caution: This will reset the mobile terminal to factory settings.
76
1.1 15.10.2014
APPENDIX Glossary
10.
Appendix
10.1
Glossary ADB log
[Abbr. for Android Debug Bridge]; This is a software interface for the Android operating system. It can be used by a connected computer to interact with the mobile terminal using the command line.
AES
[Abbr. for Advanced Encryption Standard]; A symmetric encryption system declared as standard by the National Institute of Standards and Technology (NIST). The algorithm is freely available and can be used in software respectively hardware. No license fee.
App
[Short for application]; These are downloadable programs that can be started by pressing a button enabling the use of certain functions.
Bluetooth
Industrial standard according to IEEE 802.15.1 for a wireless network of devices over a short distance.
Calibration
Optimisation/fine adjustment of the touch
Cold start
In case of a cold start the boot loader always copies the Windows CE image from the flash to the SRAM and starts it. Here, registry and RAM file system are rebuild and registry values from the KDI and GSI block are applied.
COM
[Abbr. for Communication Port]; Communication ports are the serial interfaces COM1 and COM2.
DECT
[Abbr. for Digital Enhanced Cordless Telecommunications]; A cordless phone standard widely used in Europe with a range of up to 300 m.
DFÜ
Short for German Datenfernübertragung (Remote data transfer). Generic term for transferring data either by wire or wireless over large distances.
DRAM
[Abbr. for Dynamic Random Access Memory]; dynamic, volatile direct access memory (working memory) [Abbr. for Enhanced Data Rates for GSM Evolution]; Enhancement of data transmission rates in GSM mobile radio networks.
EDGE EDR
[Abbr. for Enhanced Data Rate]; An up-to-date Bluetooth standard that triples the Bluetooth data rate (from 723 kbit/s to 2.169 Mbit/s.
EGPRS
With EDGE GPRS data services are enhanced to E-GPRS./////
Flash memory
The flash-memory is a non-volatile memory type with a block-orientated way of work.
GPS
[Abbr. for Global Positioning System]; A system that uses satellites for position determination.
GPRS
[Abbr. for General Packet Radio Service]; Package oriented service for data transmission in GSM and UMTS networks.
1.1 15.10.2014
77
APPENDIX Glossary
GSM
[Abbr. for Global System for Mobile Communications]; Mobile radio standard of the 2. generation (2G).
Hardware reset
Depending on the hardware used the user defines settings that will be reset after a hardware reset. A hardware reset always come with a software restart. In case of a hardware reset it is not possible to shutdown the system i.e. to close network connections or to flush file systems. A hardware reset always results in a cold start.
HSDPA
[Abbr. for High Speed Downlink Packet Access]; Data transmission process of the UMTS mobile phone standard.
Launcher
The Launcher is a program that manages frequently used applications and programs and that enables the user to directly execute them via the touch screen.
LED
[Abbr. for Light Emitting Diode]
LTE
[Abbr. for Long Term Evolution]; (4G) This is the UMTS (3G) successor
RAM
[Abbr. for Random Access Memory]; Volatile (working) memory with random access
Registry
A central hierarchical database storing important information on system configuration, user, applications, and hardware devices.
Reset
Resets the computer to a defined state.
SDRAM
[Abbr. for Synchronous Data Random Access Memory]
SIP
[Abbr. for Soft Input Panel]; Virtual shown keyboard on the screen.
SoftwareReset
A software reset can be a preparatory action like a "soft shutdown" of the system but does not generate the same states at the start as a hardware reset. A software reset may trigger either a cold or a warm start.
SSID
[Abbr. for Service Set Identifier]
SVGA
[Abbr. for Super Video Graphics Array]; Graphics standard with a resolution of 800 x 600 pixel
UMTS
[Abbr. for Universal Mobile Telecommunications System]; Mobile radio standard of the 3. generation (3G)
VPN
[Abbr. for Virtual Private Network]; defines the construction of a secure communication channel (also called tunnel) via the Internet. VPN encrypts data packages of any protocol and transmits them via the Internet. [Abbr. for Universal Serial Bus]; A bus system to connect a computer to external USB peripheral devices for exchanging data.
USB
VPN
78
1.1 15.10.2014
[Abbr. for Virtual Private Network]; defines the construction of a secure communication channel (also called
APPENDIX Glossary tunnel) via the Internet. VPN encrypts data packages of any protocol and transmits them via the Internet. Warm start
In case of a warm start the system available in the SDRAM is restarted. Registry and RAM file system are maintained. KDI and GSI are not evaluated.
WEP
[Abbr. for Wired Equivalent Privacy]; Encryption type used in wireless local area networks according to IEEE standard 802.11.
Widget
A widget is a component of a graphical window system. A widget consists of a window, a visible area that receives mouse and/or keyboard events and a non visible object that stores the status of the component and that can change the visible area via certain character operations.
WPA
[Abbr. for WiFi (Wireless Fidelity) Protected Access]; a specification for standardised compatible security improvements improving data protection (encryption) and access control (authentication) for existing and future wireless WiFi LAN systems.
WPA2
[Abbr. for Wi-Fi (Wireless Fidelity) Protected Access 2]; Implementation of a security standard for radio networks according to WLAN standard IEEE 802.11a, b, g on the base of the Advanced Encryption Standard (AES). It replaces the WPA which bases on the Wired Equivalent Privacy (WEP) which is supposed to be unsecure. WPA2 is an additional protection measurement that uses dynamic keys on the base of the Temporal Key Integrity Protocol (TKIP). To authenticate user PreShared Keys (PSK) or Extensible Authentication Protocol (EAP) IEEE 802.1x is used.
1.1 15.10.2014
79
APPENDIX Index 10.2
Index Showing 35
—A— Accessory 19 Automatic Standby 29
—B—
Mobile radio 57 Connection 57 Mobile radio module 71
BarcodeScanner 42 Battery 26 Charging 28 Charging time 69 Inserting 26 Replacing 27 Bluetooth 59 Settings 59 Bluetooth module 71 Brightness 36
—N—
—C—
Power Off 31
Characteristics 6 Communication Cradle 20, 61 Charging the battery 69 Connecting with Ethernet 66 Connecting with PC 65 Ethernet connection 62 HW 50250 61 HW 50253 61 LED HW 50250 67 LED HW 50253 68 Technical Data 63 USB Connection 62 Complete Power Off 31
—R—
—D— Disposal 17
—F— Factory settings 76
—G— GPS 60 GPS module 71
—H— Hardware Equipment 19 Home Screen 33
—I— Imager module 72, 74 Initial Steps 32
—K— Keyboard Settings 38
80
—M—
1.1 15.10.2014
Navigation key 32
—O— Operating system Update 54
—P—
Radio module 55 Switching on/off 53 Reset Hardware 75
—S— Safety Notes 9 Battery 11, 14 Communication Cradle/Battery Recharger 14 Data Loss 17 General 9 GPS 17 Imager with Laser Aimer 16 Imager with LED Aimer 16 Laser 15 Mobile radio 16 Power Supply 15 WLAN 17 Scan Key 41 Scanner module 72, 73 Scanner operation 40 Scanning 42 Settings 44 Scanning positions 41 SD Card 24 Serial number 6 Settings 35 Settings: 34 SIM Card 25 skeye.allegro Front view 21 Keyboard 23 Modules 71 Rear view 22 Technical data 70 Variants 18 Software Equipment 19
APPENDIX Index Sound 51 Stylus 32 Tapping 32 Tapping and Hodling 32 Suspend Mode 29 Switching off 29 Switching on 29 Symbols 35 SysInfo Calling report file 48 GSI-Block 46 HWI-Block 46 Mac Address 46 Memory 46 Report file 47
Versions 46 System information 45, See SysInfo
—T— Trademarks 9 Troubleshooting 75
—W— WiFi See WLAN WLAN 55 WLAN module 71
1.1 15.10.2014
81
APPENDIX Index
82
1.1 15.10.2014
APPENDIX Manufacturer's Address 10.3
Manufacturer's Address Höft & Wessel AG Rotenburger Str. 20 30659 Hannover, Germany Phone. +49 511 6102-0 Fax. +49 511 6102–713 Web. www.hoeft-wessel.com Mail.
[email protected] Serviceline. Phone. +49 511 6102-600 Fax. +49 511 6102-601 Mail.
[email protected]
1.1 15.10.2014
83
