Transcript
ENGLISH
GLOW UP STRIP 100 & FLIGHT CASE
C71080 F21250
INSTRUCTIONS MANUAL
Congratulations on choosing a Clay Paky product! We thank you for your choice. Please note that this product, as all the others in the rich Clay Paky range, has been designed and manufactured with total quality to ensure excellent performance and best meet your expectations and requirements. Carefully read this instruction manual in its entirety and keep it safe for future reference. It is essential to know the information and comply with the instructions given in this manual in order to ensure the fitting is installed, used and serviced correctly and safely. CLAY PAKY S.p.A. disclaims all liability for damage to the fitting or to the other property or persons deriving from installation, use and maintenance that have not been carried out in conformity with this instructions manual, which must always accompany the fitting. CLAY PAKY S.p.A. reserves the right to modify the characteristics stated in this instructions manual at any time and without prior notice.
INDEX Page Contents 2
Safety Information
4
Unpacking and preparation
4
Removal of the protective film
4
Installation and start-up
6
Control panel
8
Button function
9
Preset colors for Stand Alone
10
Menu set
20
Operating Mode
21
RDM Controls implemented for GLOWUP series
21
Aerial
22
Maintenance
24
Optional accessories
25
Technical data
25
Cause and solution of problems
26
Channel functions 1
SAFETY INFORMATION
EN
• Installation Make sure all parts for fixing the projector are in a good state of repair. Make sure the point of anchorage is stable before positioning the projector. The safety chain must be properly hooked onto the fitting and secured to the framework, so that, if the primary support system fails, the fitting falls as little as possible. If the safety chain gets used, it needs to be replaced with a genuine spare. Ensure that the Flight Case, when used for charging Glow UP, is positioned at a distance of 15 cm from any surface or wall, to allow proper ventilation.
LED
• Minimum distance of illuminated objects The projector needs to be positioned so that the objects hit by the beam of light are at least 0.2 metres (8”) from the lens of the projector.
0.2
• Minimum distance from flammable materials The projector must be positioned so that any flammable materials are at least 0.20 metres (8") from every point on the surface of the fitting.
ta 40°C
• Maximum ambient temperature Do not use the project if ambient temperature (Ta) exceeds 40°C.
GLOW UP STRIP 100
IP65
• IP65 protection rating The equipment is fully protected against dust (first digit 6) and against jets of water (second digit 5).
FLIGHT CASE
IP20
• IP20 protection rating The fitting is protected against penetration by solid bodies of over 12mm (0.47”) in diameter (first digit 2), but not against dripping water, rain, splashes or jets of water (second digit 0). • Protection against electrical shock Connection must be made to a power supply system fitted with efficient earthing (Class I appliance according to standard EN 60598-1). It is, moreover, recommended to protect the supply lines of the projectors from indirect contact and/or shorting to earth by using appropriately sized residual current devices. • Connection to the power mains A qualified electrician must perform connection to the power mains. Check that the mains frequency and voltage correspond to the frequency and voltage for which the projector was designed and indicated on the electrical data label. This label also gives the input power. Refer to the latter to evaluate the maximum number of devices to be connected to the mains to avoid overloads.
tc 90°C
• External surface temperature The maximum temperature that can be reached on the external surface of the fitting, in a thermally steady state, is 90°C (194°F). • Maintenance Before starting any maintenance work or cleaning the projector, cut off power from the supply mains. After switching off, do not remove any parts of the fitting for at least 10 minutes. The lenses must be mounted and, if visibly damaged, they have to be replaced with genuine spares. • Photobiological Safety Risk Group 2
Risk Group 2 According to EN 62471
CAUTION. Possibly hazardous optical radiation emitted from this product. Do not stare at operating lamp. May be harmful to the eye.
This product is intended for the following areas of application: studios, stages, theaters, exhibitions, trade fairs, events, theme parks, entertainment venues, architectural lighting and similar
GLOW UP STRIP 100
2
Not suitable for household illumination
Not for residential use
LiFePO4
• Battery This product contains a lithium iron tetraphosphate rechargeable battery. To protect the environment, please discard the battery at the end of its life cycle according to current law.
Disposing This product is supplied in compliance with European Directive 2012/19/EU - Waste Electrical and Electronic Equipment (WEEE). To preserve the environment please dispose/recycle this product at the end of its life according to the local regulation.
The products to which this manual refers comply with the European Directives pursuant to: • 2014/35/EU - Safety of electrical equipment supplied at low voltage (LVD) • 1999/5/EC – Requirements for radio equipment (R&TTE) • 2011/65/EU - Restriction of the use of certain hazardous substances (RoHS) • 2009/125/EC - EcoDesign requirements for Energy-related Products (ErP)
EN
IT
DE
ES
FR
RU
GLOW UP STRIP 100
HOW TO GET YOUR SAFETY INSTRUCTIONS IN MULTILINGUAL VERSION You may always download the multilingual Safety Instruction manual for this Clay Paky product from: http://www.claypaky.it/en Ref: [FIS012 – Safety Information GlowUp series] COME OTTENERE LE INFORMAZIONI DI SICUREZZA NELLA VERSIONE MULTILINGUE Puoi sempre scaricare la versione multilingue delle Informazioni di Sicurezza per questo prodotto Clay Paky al seguente link: http://www.claypaky.it/en Rif: [FIS012 – Safety Information GlowUp series] SO ERHALTEN SIE IHR INFORMATIONEN ZUR SICHERHEIT IN DER MEHRSPRACHIGEN VERSION Sie können die mehrsprachige Version des Handbuchs mit Sicherheitshinweisen für dieses Clay Paky-Produkt unter folgendem Link herunterladen: http://www.claypaky.it/en Ref: [FIS012 – Safety Information GlowUp series] COMO OBTENER TU INFORMACIONES DE SEGURIDAD EN LA VERSION MULTILINGUE Siempre puedes descargar la versión multilingüe del Manual de Instrucciones de Seguridad para este producto Clay Paky en el siguiente enlace http://www.claypaky.it/en Ref: [FIS012 – Safety Information GlowUp series] COMMENT OBTENIR VOTRE CONSIGNES DE SÉCURITÉ DANS LA VERSION MULTILINGUE Vous pouvez toujours télécharger la version multilingue du Manuel d’Instructions de Sécurité pour ce produit Clay Paky au lien suivant : http://www.claypaky.it/en Réf. : [FIS012 – Safety Information GlowUp series] ГДЕ ДОСТАТЬ ИНСТРУКЦИЮ ПО ТЕХНИКЕ БЕЗОПАСНОСТИ НА НЕСКОЛЬКИХ ЯЗЫКАХ Вы всегда можете скачать многоязычную инструкцию по технике безопасности для данного изделия Clay Paky по ссылке: http://www.claypaky.it/en Наименование: [FIS012 – Safety Information GlowUp series] 3
UNPACKING AND PREPARATION 1
2 x 183102/805
Packing content - Fig. 1
REMOVAL OF THE PROTECTIVE FILM 2
1
INSTALLATION AND START-UP 3
3
2
2
1
2
max 90°
3
GLOW UP STRIP 100
2
4
3 2 3 1
3 1
5
4 5
4
Projector installation - Fig. 3 The projector can be installed on the floor resting on specific rubber feet, on a truss, on the ceiling or wall. WARNING: the safety chain must be installed except when the projector rests on the floor. (Code 105015/801 available upon request). This must be secured to the projector support structure and then hooked to the fastening point at the centre of the base. GLOW UP STRIP 100
5
Continued
➔
4
1
1
4
3
3 2
2
Connecting and disconnecting the power cord - Fig. 4 When connecting the power cord the user can choose whether to use the GLOW UP in one of the following ways: 1) Power cord connected for battery charge. 2) Power cord connected for projector power (thus bypassing battery operations). The GLOW UP cannot work in both ways simultaneously.
CONTROL PANEL 5
Power Supply
Connections to the power mains - Fig. 5
6
DMX 512
DMX 512 5 PIN
Connections to the control signal line (DMX) - Fig. 6 Use a cable conforming to specifications EIA RS-485: 2-pole twisted, shielded, 120Ω characteristic impedance, 22-24 AWG, low capacity. Do not use microphone cable or other cable with characteristics differing from those specified. End connections must be made using XLR type 3-pin male/female connectors. A terminating plug must be inserted on the last projector with a resistance of 120 (minimum 1/4 W) between terminals 2 and 3. IMPORTANT: The wires must not make contact with each other or with the metal casing of the connectors. The casing must be connected to the shield braid and pin 1 of the connectors.
GLOW UP STRIP 100
6
7
Switching on the projector - Fig. 7 The projector immediately turns on when the power cord is plugged in or, if used in battery mode, by pressing and holding down keys several seconds. Clay Paky GLOW UP STRIP 100
GLOW UP STRIP 100 Software release x.x x
Address xxx xxxxx
A and S for
BAT xx%
The control panel (Figure 8) has a display and buttons for complete programming and management of the projector menu. The display can be in one of two conditions: idle status and settings status. When idle, the projector DMX address and percent battery charge are displayed. If no button is pressed after a wait period (about 60 seconds) when in menu settings status, the display automatically returns to idle status. It should be noted that when this condition occurs, any modified value that has not yet been confirmed with the key will be cancelled. To turn off the GlowUP, hold down keys and for several seconds. A confirmation message will appear (Switch off?). Press -Yes to turn off the GlowUP or press -NO to return to the settings menu.
A
A
A
S S
When GlowUp is in idle status the information page will appear on the display: DMX Address
Time or percent remaining of the battery charge ADDR 001 STND
Operating mode (see page 23)
BAT 40% Yy Link status (Wireless or Wired)
FRES/W Factory reset? Y/N Warning Radio W42 (radio board not found) W43 (radio board not interact) If errors W42/W43 appear on the display, do an RDM Discovery (see page 14) to see if the error disappears. If it does not, check the intactness of the wireless board.
Display symbology - (Link Status) Transmission to DMX cable
Reception from DMX cable
Reception DMX from Radio (wireless)
Transmission DMX from Radio (wireless)
Initial projector address settings An initial address must be set on each single project for the control signal. Address settings: see page 12. GLOW UP STRIP 100
7
Continued
➔
Button functions – Menu SET SELECT
• If pressed in idle status: Cyclically switches between idle status and menu settings. • If pressed while setting a menu: Moves to an upper level without changing anything (exits the function)
DOWN
Decreases the value displayed (with auto-repetitions), or passes to the next item on the menu For quick access to the minimum parameter value, press the UP key while holding down the DOWN key.
UP
Increases the value displayed (with auto-repetitions), or passes to the previous item on the menu For quick access to the maximum parameter value, press the DOWN key while holding down the UP key.
ENTER Confirms the displayed value or activates the displayed function or opens the next menu.
BUTTON FUNCTION By pressing any button when Glow Up is in idle status, the BUTTON FUNCTION menu is accessed. Symbol
SET
or II
MOD
Function
Setting
Play/Pause
Stop
Mode
?? SET
BAT 40% MOD
S
Press SET SELECT to access the menus: Program DMX Address Advanced (Menu use is recommended for qualified technical personnel.)
Press ENTER
A MOD to select the Glow UP operating mode
Mode
Stand Alone DMX Slave Master Repeater
NOTE: in a GlowUp series which is part of a battery, it is imperative to first select all the receivers and finally select the Transmitter.
II PLAY/PAUSE UP
Bkey: activates or pauses a particular mode.
Play
Preset Colors Sequences Manual Control Play Rec
STOP DOWN
C key: deactivates the active programme.
GLOW UP STRIP 100
8
PRESET COLORS FOR STAND ALONE
Colour
Reference
01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52
LEE 101 LEE 103 LEE 105 LEE 107 LEE 111 LEE 113 LEE 115 LEE 116 LEE 119 LEE 128 LEE 132 LEE 134 LEE 135 LEE 136 LEE 147 LEE 180 LEE 156 LEE 079 LEE 194 LEE 024 LEE 017 LEE 019 LEE 108 LEE 126 LEE 141 ROSCO 378 ROSCO 358 ROSCO 081 ROSCO 066 ROSCO 030 ROSCO 318 ROSCO 332 ROSCO 034 ROSCO 039
RGBW RED GREEN BLUE YELLOW CYAN MAGENTA WHITE ORANGE PINK VIOLET AQUA SKY BLUE FULL WHITE COOL WHITE WARM WHITE WHITE 3200 WHITE 2500 YELLOW 2 STRAW ORANGE LIGHT ROSE DARK PINK MAGENTA BLUE 2 MED BLUE GREEN DARK BLUE BRIGHT PINK MEDIUM BLUE GOLDEN AMBER DEEP GOLDEN AMBER PALE LAVENDER APRICOT DARK LAVENDER CHOCOLATE JUST BLUE SURPRISE PINK SCARLET SURPRISE PEACH FIRE ENGLISH ROSE MAUVE BRIGHT BLUE ALICE BLUE ROSE INDIGO URBAN BLUE COOL BLUE LIGHT SALMON MAYAN SUN CHERRY ROSE FLESH PINK SKELTON EXOTIC SANGRIA
GLOW UP STRIP 100
R 0 255 0 0 255 0 255 0 255 127 255 85 118 255 225 255 255 255 133 255 246 218 255 255 0 0 0 255 0 255 255 0 152 0 238 0 78 255 145 255 161 255 0 0 0 0 0 255 150 255 255 255
Bit value G B 0 0 0 0 255 0 0 255 255 0 250 185 0 140 0 0 115 0 0 0 0 184 255 105 255 150 255 255 255 253 255 220 176 0 99 0 145 0 255 0 195 0 0 0 0 120 0 78 255 175 255 160 180 180 0 141 255 200 175 0 140 0 0 100 122 0 114 144 189 0 187 175 0 0 0 58 0 0 141 44 119 0 0 208 255 186 255 223 0 255 255 187 255 148 112 0 114 0 0 92 0 132 0 180
9
W 0 0 0 0 0 0 0 100 0 100 200 0 0 255 255 255 255 255 0 240 0 255 255 0 0 0 0 95 0 25 25 190 76 112 227 0 255 113 153 0 255 150 37 140 133 35 153 162 162 0 255 100
Continued
➔
MENU SET
GLOW UP STRIP 100
10
GLOW UP STRIP 100
11
Continued
➔
SELECT
DOWN UP
GLOW UP STRIP 100
ENTER
12
GLOW UP STRIP 100
13
Continued
➔
GLOW UP STRIP 100
14
GLOW UP STRIP 100
15
Continued
➔
GLOW UP STRIP 100
16
GLOW UP STRIP 100
17
Continued
➔
GLOW UP STRIP 100
18
GLOW UP STRIP 100
19
OPERATING MODES
Operating Mode Stand Alone DMX
Descrizione Does not receive DMX and executes only the Play Receives DMX Slave Glow UP receives (on address 1) if the GlowUp Master is set in Play sequences.
Slave
Master Repeater
GLOW UP STRIP 100
Display STND DMX
SLV Slave Glow UP receives on its DMX address if GlowUp Master transmits a recording DMX Broadcasts sequences or recording DMX Receives and repeat, depending on the configuration set in the '' Advance Menu’’.
20
MAST RPTR
RDM CONTROLS IMPLEMENTED FOR GLOWUP SERIES
Control
PID
GET
SET
Description controller side
DEVICE_INFO
0x0060
X
IDENTIFY_DEVICE
0x1000
DMX_START_ADDRESS
0x00F0
X
SOFTWARE_VERSION_LABEL
0x00C0
X
Reads the firmware version
SUPPORTED_PARAMETERS
0x0050
X
Gathers the PIDS on the non-basic controls
PARAMETER_DESCRIPTION
0x0051
X
Gathers information on the controls related to the manufacturer
DMX_PERSONALITY
0x00E0
X
DMX_PERSONALITY_DESCRIPTION
0x00E1
X
Reads the description of the channel mode
MANUFACTURER_LABEL
0x0081
X
Reads the manufacturer name
DEVICE_LABEL
0x0082
X
SENSOR_DEFINITION
0x0200
X
Reads the description of the sensors present
SENSOR_VALUE
0x0201
X
Reads the level of the led temperature sensor
RECORD_SENSORS
0x0202
DEVICE_MODEL_DESCRIPTION
0x0080
Gathers information from the device X
Makes the red leds on the addressed device pulse
X
Reads or sets the DMX address
X
X
X
Reads or sets the channel mode
Reads or writes a label on the device
Saves the current temperature level Reads the text description of the model
X
AERIAL 8
Aerial
NOTES: To achieve best wireless performance, it is recommended to position GLOW UP with the aerial side facing the transmitter, when possible.
GLOW UP STRIP 100
21
MAINTENANCE 9
5
90°
3 4
2
1 Charging GLOW UP - Fig. 9 From 1 to 4 GLOW UPs can be simultaneously charged by appropriately connecting and powering the flight-case.
10 Fuse 6,3x32mm 2.5AT 250Vac (FUS000)
1
Fuse 6,3x32mm 10AT 250Vac (030470)
2 Replacing flight case fuses - Fig. 10 Each flight-case has 2 fuses associated with the main power cord connection and one fuse for each GLOW UP charge station. GLOW UP STRIP 100
22
11
1
3
2
3
1
2 3
3 2
Battery removal - Fig. 11 This product contains lithium iron tetraphosphate rechargeable battery. To protect the environment, please discard the battery at the end of its working life according to current law. LiFePO4
Notes on how to achieve correct battery operations 1) Do not tamper with the control electronic circuit, do not tamper with the battery, do not short-circuit the battery. 2) Do not reuse GLOW UP after self-switch off as this indicates a low battery; recharge GLOW UP before using it again. 3) Do not leave the battery completely flat for over 5 days. 4) When not in use, recharge the battery at least every 4 months.
GLOW UP STRIP 100
23
Continued
➔
12
Parts requiring frequent cleaning. Periodic cleaning - Fig. 12 To ensure optimal operation and performance for a long time it is essential to periodically clean the parts subject to dust and grease deposits. The frequency with which the following operations are to be carried out depends on various factors such as wear and the work environment quality (air humidity, dust, salinity, etc.). To remove dirt from external parts, use a soft cloth dampened with any liquid glass cleaning detergent. It is recommended that the projector undergoes an annual service by a qualified technician for special maintenance involving at least the following operations: • General cleaning of internal parts. • General visual check of internal parts, cabling, mechanical parts, etc. • Electrical, photometric and functional checks; eventual repairs.
OPTIONAL ACCESSORIES 13
C61460 C61461
C61460 - longitudinal elliptic diffuser C61461 - cross elliptic diffuser GLOW UP STRIP 100
24
TECHNICAL DATA • Repeater: Receives the signal from the master and re-transmits it to other Slaves hidden from the master • XLR 5-pole DMX-in DMX-out standard sockets • Default macros, user programmable macros. • DMX recorder to save scene sequences.
Source 10x LED RGBW Ostar (OSRAM) Led pilot power 100W Total output Max 3400 lumens
User interface • LCD display 2 lines with 16 characters each, backlit LED, white on black • 4 membrane buttons
Optics Electronically controlled optic zoom
External power Full range 100-240V 50-60Hz, PowerCon connector, for both battery charge and normal operations
LED color temperature 6000K Head adjustment 0 - 90°
Input Power • 200 VA GLOW UP STRIP 100 • 650 VA Flight Case
Cooling Natural Convection Control • Wireless DMX multimode: Master, Slave and Repeater • Antenna built in the case IP65 • Master: can transmit other slaves the synchronised DMX scenes saved on it, both as macros and as DMX recorder.
Body • Body extruded in black anodized aluminium • 2 carrying handles • 4 non-slip rubber feet
Safety Eyebolts for safety cables Weight 15 Kg Protection rating IP65 Valves Compensation valve IP65 Battery • Duration 5 hours full • Carica da Flight Case o con PowerCon • More than 2000 charge/deplete cycles • No memory effect • No acid leaks Working position Works in any position
Fittings 4 fast-look holes for omega hook-up
115 (4.53")
1000 (39.37")
130 (5.12")
230 (9.06") 170 (6.69")
CAUSE AND SOLUTION OF PROBLEMS THE PROJECTOR WILL NOT SWITCH ON
TROUBLE
THE PROJECTOR WILL NOT SWITCH ON DEFECTIVE PROJECTION
POSSIBLE CAUSES
CHECKS AND REMEDIES
REDUCED LUMINOSITY
No power supply. LED burnt out or defective. Signal transmission cable faulty or disconnected. Incorrect addressing. Fault in the electronic circuits. Optic fault. Dust or grease deposits.
GLOW UP STRIP 100
Check the power supply voltage or battery charge. Call an authorised technician. Replace the cables. Check addresses (see instructions). Call an authorised technician. Call an authorised technician. Clean (see instructions).
25
CHANNEL FUNCTIONS
GLOW UP STRIP 100
CHANNEL
COMMON MODE
SINGLE MODE
1
RED
RED
2
GREEN
GREEN
3
BLUE
BLUE
4
WHITE
WHITE
5
DIMMER
RED
6
STROBE
GREEN
7
MACRO COLOR
BLUE
8
ZOOM
WHITE
9
DIMMER
10
STROBE
11
MACRO COLOR
12
ZOOM
GLOW UP STRIP 100
26
COMMON MODE • RED - channel 1
• DIMMER - channel 5 BIT 255
0
BIT
EFFECT
255
LED MAX BRIGHTNESS
0
LED OFF
• GREEN - channel 2
EFFECT LED MAX BRIGHTNESS
LED OFF
• STOP / STROBE - channel 6
BIT 255
EFFECT LED MAX BRIGHTNESS
LED ON
LED ON
LED ON
0
LED OFF
LED ON
• BLUE - channel 3
• MACRO COLOR - channel 7 BIT 255
0
EFFECT LED MAX BRIGHTNESS
LED OFF
• WHITE - channel 4 BIT 255
0
GLOW UP STRIP 100
EFFECT LED MAX BRIGHTNESS
LED OFF
27
BIT
EFFECT
248 - 255 240 - 247 232 - 239 224 - 231 220 - 223 216 - 219 212 - 215 208 - 211 204 - 207 200 - 203 196 - 199 192 - 195 188 - 191 184 - 187 180 - 183 176 - 179 172 - 175 168 - 171 164 - 167 160 - 163 156 - 159 152 - 155 148 - 151 144 - 147 140 - 143 136 - 139 132 - 135 128 - 131 124 - 127 120 - 123 116 - 119 112 - 115 108 - 111 104 - 107 100 - 103 96 - 99 92 - 95 88 - 91 84 - 87 80 - 83 76 - 79 72 - 75 68 - 71 64 - 67 60 - 63 56 - 59 52 - 55 48 - 51 44 - 47 40 - 43 36 - 39 32 - 35 28 - 31 24 - 27 20 - 23 0 - 19
COLD TONE WARM TONE PASTEL TONE SEQ1 SKELTON EXOTIC SANGRIA FLESH PINK CHERRY ROSE MAYAN SUN LIGHT SALMON COOL BLUE URBAN BLUE ROSE INDIGO ALICE BLUE BRIGHT BLUE MAUVE ENGLISH ROSE FIRE SURPRISE PEACH SCARLET SURPRISE PINK JUST BLUE CHOCOLATE DARK LAVENDER APRICOT PALE LAVENDER DEEP GOLDEN AMBER GOLDEN AMBER MEDIUM BLUE BRIGHT PINK DARK BLUE MED BLUE GREEN BLUE 2 MAGENTA 2 DARK PINK LIGHT ROSE ORANGE 2 STRAW YELLOW 2 WHITE 2500 WHITE 3200 WARM WHITE COOL WHITE FULL WHITE SKY BLUE AQUAMARINE VIOLET PINK ORANGE WHITE MAGENTA CYAN YELLOW BLUE GREEN RED NONE
Continued
➔
• ZOOM - channel 8 BIT
GLOW UP STRIP 100
EFFECT
255
WIDE BEAM
0
NARROW BEAM
28
SINGLE MODE • RED - channel 1
• RED - channel 5 BIT 255
0
EFFECT
BIT
LED MAX BRIGHTNESS
255
LED OFF
0
• GREEN - channel 2
EFFECT LED MAX BRIGHTNESS
LED OFF
• GREEN - channel 6
BIT 255
0
EFFECT
BIT
LED MAX BRIGHTNESS
255
LED OFF
0
• BLUE - channel 3
EFFECT LED MAX BRIGHTNESS
LED OFF
• BLUE - channel 7 BIT 255
0
EFFECT
BIT
LED MAX BRIGHTNESS
255
LED OFF
0
• WHITE - channel 4
EFFECT LED MAX BRIGHTNESS
LED OFF
• WHITE - channel 8 BIT 255
0
GLOW UP STRIP 100
EFFECT
BIT
LED MAX BRIGHTNESS
255
LED OFF
0
29
EFFECT LED MAX BRIGHTNESS
LED OFF
Continued
➔
• DIMMER - channel 9
• ZOOM - channel 12 BIT 255
0
EFFECT BIT
LED MAX BRIGHTNESS
WIDE BEAM
0
NARROW BEAM
LED OFF
• STOP / STROBE - channel 10
LED ON
LED ON
LED ON
LED ON
• MACRO COLOR - channel 11
GLOW UP STRIP 100
EFFECT
255
BIT
EFFECT
248 - 255 240 - 247 232 - 239 224 - 231 220 - 223 216 - 219 212 - 215 208 - 211 204 - 207 200 - 203 196 - 199 192 - 195 188 - 191 184 - 187 180 - 183 176 - 179 172 - 175 168 - 171 164 - 167 160 - 163 156 - 159 152 - 155 148 - 151 144 - 147 140 - 143 136 - 139 132 - 135 128 - 131 124 - 127 120 - 123 116 - 119 112 - 115 108 - 111 104 - 107 100 - 103 96 - 99 92 - 95 88 - 91 84 - 87 80 - 83 76 - 79 72 - 75 68 - 71 64 - 67 60 - 63 56 - 59 52 - 55 48 - 51 44 - 47 40 - 43 36 - 39 32 - 35 28 - 31 24 - 27 20 - 23 0 - 19
COLD TONE WARM TONE PASTEL TONE SEQ1 SKELTON EXOTIC SANGRIA FLESH PINK CHERRY ROSE MAYAN SUN LIGHT SALMON COOL BLUE URBAN BLUE ROSE INDIGO ALICE BLUE BRIGHT BLUE MAUVE ENGLISH ROSE FIRE SURPRISE PEACH SCARLET SURPRISE PINK JUST BLUE CHOCOLATE DARK LAVENDER APRICOT PALE LAVENDER DEEP GOLDEN AMBER GOLDEN AMBER MEDIUM BLUE BRIGHT PINK DARK BLUE MED BLUE GREEN BLUE 2 MAGENTA 2 DARK PINK LIGHT ROSE ORANGE 2 STRAW YELLOW 2 WHITE 2500 WHITE 3200 WARM WHITE COOL WHITE FULL WHITE SKY BLUE AQUAMARINE VIOLET PINK ORANGE WHITE MAGENTA CYAN YELLOW BLUE GREEN RED NONE
30
IST003/001 – EN - Rev.D 04/2016
CLAY PAKY S.p.A. - Via Pastrengo, 3/b - 24068 Seriate (BG) Italy - Tel. +39-035-654311 - Fax +39-035-301876 - www.claypaky.it
