Transcript
Manufacture’s Limited Warranty for
Pull Behind Accessories
The limited warranty set forth below is given by Precision Products Incorporated with respect to new merchandise purchased and used in the United States, its possessions and territories.
forth in this warranty provide the sole and exclusive remedy arising from the purchase. Precision Products Inc. will not be liable for incidental or consequential loss or damage including, without limitation, expenses incurred for substitute or replacement lawn care services, or for rental expenses to temporarily replace a warranted product.
Precision Products Incorporated warranties the product(s) listed against defects in material and workmanship, and will at our option, repair or replace, free of charge, any part found to be defective in materials or workmanship. This limited warranty shall only apply if this product has been assembled, operated, and maintained in accordance with the owner’s manual furnished with the product, and has not been subject to misuse, abuse, neglect, accident, improper maintenance, alteration, vandalism, theft, fire, water, or damage because of other peril or natural disaster.
Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the above exclusions or limitations may not apply to you.
PO Box 326 Farmingdale, NJ 07727 www.jonathangreen.com
During the warranty period, the exclusive remedy is replacement of the part. In no event shall recovery of any kind be greater that the amount of the purchase price of the product sold. Alteration of safety features of the product shall void this warranty. You assume the risk and liability for loss, damage, or injury to you and your property and/or to others and their property arising out of the misuse or inability to use this product.
Normal wear parts or components thereof are subject to separate terms as follows: All normal wear parts or component failures will be covered on the product for a period of one year. Parts found to be defective within the warranty period will be replaced at our expense. Our obligation under this warranty is expressly limited to the replacement or repair, at our option, of parts found to be defective in material and workmanship.
This limited warranty shall not extend to anyone other than the original purchaser or to the person for whom it was purchased as a gift.
Contacting Service
Local Law to this Warranty
Warranty parts replacements are available, ONLY WITH PROOF OF PURCHASE, through our Customer Service Department.
This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Call 1 (800) 225-5891
GO-GREEN ROTARY SPREADER
Warranty Period
This limited warranty does not provide coverage in the following cases: 1. Routine maintenance items such as lubricants and filters. 2. Normal deterioration of the exterior finish due to use or exposure. 3. Transportation and/or labor charges.
The warranty period stated below begins with the Proof of Purchase. Without the proof of purchase, the warranty period begins from the date of manufacture. Product Warranty Period The warranty period for this product is as follows: All parts are covered for 1 year.
No implied warranty, including any implied warranty of merchantability of fitness for a particular purpose, applies after the applicable period of express written warranty above as to the part as identified below. No other expressed warranty, whether written or oral, except as mentioned above, given by any person or entity, including a dealer or retailer, with respect to any product, shall bind Precision Products Inc. during the period of the warranty, the exclusive remedy is repair or replacement of the product as set forth above. The provisions as set
Rock Salt is not recommended for use in this Spreader. Remove agitator when using Ice Melt.
Manual Contents Safety Instructions Assembly Operation Maintenance Parts Warranty
2 2 2 2 3 4
Your New Broadcast Spreader Congratulations on your purchase of a new Precision Products Inc. Broadcast Spreader. Your aerator has been engineered and built to give you the most dependable and best performing product possible. If you experience any problem you can not easily resolve, please feel free to contact our knowledgeable and helpful customer service department toll-free at 1 (800) 225-5891.
Caution: Carefully read all rules and instructions for safe operation. Retain this manual for reference. 8
(Rev. 11/12)
Rules for Safe Operation 14
The following safety precautions are suggested. This broadcast spreader is designed, engineered and tested to offer reasonably safe and effective service, provided that it is operated in strict accordance with these instructions. Failure to do so may result in personal injury. Always observe the rules of safe operation. Please read and retain this manual.
19
9
9
18
15 7
18
1. Do not allow anyone to operate the broadcast spreader without proper instructions.
6
1
17
10
2. Do not permit children to operate or ride on the broadcast spreader. 3. Wear eye and hand protection when handling or applying lawn or garden chemicals. 4. Read the chemical label instructions and cautions for handling and applying the chemicals purchased for spreading.
15
5. Keep all nuts, bolts and screws tight to be sure equipment is in safe working condition. 6. Follow maintenance and lubrication instructions as outlined in this manual.
12
2
17
3
7. Always wear substantial footwear. Do not wear loose fitting clothing that can get caught in moving parts.
11
17
8. Stay alert for holes in the terrain and other hidden hazards.
20
16
21 4
17
Operation
12
See Broadcast Spreader Operation and Application Chart.
5 13
Maintenance Instructions
8
20 16
After each use, wash unit thoroughly, let dry. Lubricate all moving parts, including slide plate, axle and upright shaft with light oil.
8 21
Assembly Instructions 1. Remove Spreader from the carton. Ref. Part No.
2. Lift handle to upright position.
1 2 3 4 5 6 7 8 9 10 11
3. Tighten two wing nuts, as shown in Figure 1.
2
3936 1307 2614 2699GY 3948 1008 1042 1002GY 6129 1048GY 1032GY
Qty. 1 1 1 1 1 1 1 2 2 1 1
Description
Ref. Part No.
Hopper Slide Plate Spinner Disc Axle Gear Case Assembly 3/8” Retaining Ring Agitator Clip Hopper Support 1/4” x 1-1/2” Hex Head Bolt Handle Leg
12 13 14 15 16 17 18 19 20 21
7
1916L 1040 1868 2828 5118 1408 1817 2441 1270 2680
Qty. 2 2 1 3 2 6 2 1 4 2
Description Wheel 1/2” Hubcap 1/4” x 2-1/4” Carriage Bolt 1/4” Wing Nut 1/4” KEPS Nut 1/4” x 1-3/4” Carriage Bolt 1/4” Flat Washer Control Cable Assembly 1/4” Hex Nut Split Bushing/Spacer
Calculating Your Flow Setting
Caution On the bag of fertilizer there should be a chart that gives the recommended settings for that particular bag. Because different manufactures of fertilizer make the granules different sizes it is impossible for spreader manufactures to give guidelines for all of the different fertilizers. In addition to this walking speed and terrain, may vary, therefore settings may need to be adjusted. Because of these conditions, Precision Product Inc. makes no warranty as to the uniformity of coverage actually obtained from any of these calculations.
To calculate how many pounds of material to spread per 1000 square feet of lawn. Follow these steps. 1. Read on your material bag how many square feet of area the contents of the bag will cover and how many pounds the bag weighs. Example: You have purchased a bag of fertilizer that states that it will cover 5,000 square feet, and weighs 16.0 pounds. 2. To calculate coverage divide bag weight by suggested coverage to obtain pounds per square foot that is needed to be applied. Example: 16.0 lbs. ÷ 5,000 sq. ft. = .0032 lbs./sq. ft. 3. To calculate how much you need for 1000 sq. ft. multiply the pounds per square foot obtained above by 1000. Example: .0032 lbs/sq. ft. x 1000 = 3.2 lbs./1000 sq. ft.
Wing Nuts
_____________________Length X_____________________Width =_____________________Total sq. ft.
4. Refer to standard settings table and locate the appropriate settings number. Example: 3.2 lbs./1000 sq. ft is closest to a 3 lbs./1000 sq. ft so the spreader setting is a 5.
-______________________Non-Lawn Area House, drive etc. =_____________________Total sq. ft. Coverage
These are general information setting intended to be used as only references.
STANDARD SETTINGS Setting Broadcast Spreaders
2.5 3.0 3.5 4.0
4 5 5.5 6
Grass Seed
Setting
Blue Grass Bent Grass Fine Mixture Coarse Seed
3 3 10 10
Insecticide (Diazinion)
Setting 3.5
CALCULATING COVERAGE AREA
Length
Width
Fertilizer Lbs. per 1000 sq. ft.
Figure 1 6
3
Using your Spreader Controller
Broadcast Spreader Application Chart
Storage Applying Product
1. Rinse inside of hopper and exterior of spreader. 2. Store in a clean, dry area.
See Application Chart for Setting Information.
DO NOT allow spreader to sit stationary with material in the hopper and control lever in the ON position.
Broadcast Spreader Operation
Control Lever
1. Set Flow Rate Calculate or find the rate setting for the product being spread. See the calculation chart on the next page. With control lever in the off position, press down on the calibration indicator button and slide it to desired setting number. 2. Fill the Hopper With the spreader control lever in the off position, fill the spreader over a patch of bare ground or sidewalk/driveway. DO NOT fill the spreader on the lawn. Sweep up any spilled product.
Calibration Indicator Button
OF F
Settings are made by loosening the Wing Nut and sliding the Calibration Indicator to the desired setting, tighten the Wing Nut. Pull the Control Lever to the desired setting and begin spreading. To stop fertilizer distribution, push the Control Lever forward, to the closed position.
Settings Numbers
3. Apply
1. Always have the control lever in the OFF position before filling the hopper. 2. Always push the spreader forward to operate; do not operate in reverse. 3. Start moving forward before pushing the control lever to the ON position. Pull the control lever to the OFF position before stopping or turning. 4. Push the spreader at a steady speed. 5. To avoid misses or striping, space each pass across the lawn so approximately 20% of the spread width overlaps the previous pass. This provides a feathered overlap to even out distribution over the with of the spread.
CAUTION: Care must be taken with any weed killer, pesticide, or combination product. They can be harmful to other plant life in the yard.
While unit is in motion at approximately 3 miles per hour, push spreader control lever up to calibration indicator button to release product.
Figure 1
Application Tips
Parts and Support STOP
Please do not return this product to the store prior to contacting Precision.
At Precision Products Inc. our goal is to deliver quality, value and outstanding service. If for any reason our product does not meet your expectations, please contact us and we will take care of any problem you may have with this unit.
Maintenance Instructions 1. Before each use, check all nuts and bolts for tightness.
When ordering replacement parts please have the model number, part description, part number, inspector number and date available so that we can best serve you.
2. Empty hopper after each use. Do not store spreader with material left in hopper. 3. Washer spreader thoroughly and wipe dry. The key to years of trouble-free service is to keep your unit clean and dry.
1 (800) 225-5891 www.precisionprodinc.com
4. If rust should develop, sand lightly and then paint area with enamel.
Precision Products Inc. 316 Limit St. Lincoln IL 62656 4
For rectangular lawns, apply two header strips at each end of the lawn and then go back and forth between the header strips. Close spreader at the end of each pass and reopen at the start of next pass. For irregular-shaped lawns, apply one header strip around the entire lawn, and then go back and forth. To avoid streaks or misses, slightly overlap each strip over the edge of the previous strip. Use the settings under “Standard Settings” Section for most applications by figuring lbs. per 1000 square feet. These numbers are for a one pass application. A two pass application is recommended, using a crisscross pattern. If using this method, us half the setting number given. If you think too much is being applied, cut down your setting. The solution for too much fertilizer is water. Close Spreader at the end of each pass. Open again at the start of your next pass.
Over Lap
5
