Go!control

Transcript

Go!Control Installation and Programming Technical Training HARDWARE • • • • • System Capabilities What’s Inside The Transformer Terminal Block GSM Unit SYSTEM CAPABILITIES • • • • • • • 48 Wireless Zones 2 Hardwired Zones 8 Keyfobs 4 Secondary Keypads 2-Way Over GSM (default) 2-Way Over POTS (optional) 232 Z-Wave devices HARDWARE WHAT’S IN THE PANEL • • • • • • • • Third Hand RJ45 Connector (POTS) 24 HR Back-Up Battery 345Mhz Receiver Terminal Block GSM Antenna Compartment Pop-In Style GSM Unit 85dB Siren/Speaker HARDWARE THE TRANSFORMER • VDC Positive (+) Wire to port 1 (+) inside the panel • VDC Negative (-) Wire to port 2 (-) inside the panel HARDWARE TERMINAL BLOCK • • • • • • • • 8) Hardwire Zone 2 7) Hardwire Zone 1 6) External Bell (-) 5) External Bell (+) (6-12 VDC @ 120mA max) 4) Open Collector Output (250mA @16VDC max) 3) Ground (hardwire zones) 2) 14VDC Input (-) from Transformer negative (-) 1) 14VDC Input (+) from Transformer positive (+) HARDWARE GSM MODULE • Antenna Port • Mounting Screws • IMEI# (Serial Number) PROGRAMMING • Installer Toolbox – System Configuration • Programming a Zone • Programming a Keyfob • Programming a Keypad – Radio Status – System Restore – Walk Test – Disable Sounder PROGRAMMING INSTALLER TOOLBOX Press SECURITY PROGRAMMING INSTALLER TOOLBOX Press MENU PROGRAMMING INSTALLER TOOLBOX Press TOOLBOX PROGRAMMING INSTALLER TOOLBOX Press RIGHT ARROW PROGRAMMING INSTALLER TOOLBOX Press RIGHT ARROW PROGRAMMING INSTALLER TOOLBOX Press INSTALLER TOOLBOX PROGRAMMING INSTALLER TOOLBOX Installer Code (1561) PROGRAMMING INSTALLER TOOLBOX Press SYSTEM CONFIGURATION PROGRAMMING SYSTEM CONFIGURATION NAVIGATION • Navigated by Questions rather than Field Values – Q1: Wireless Zones – Q2: Hardwire Zones – Q3: Keyfobs – Q4: Wireless Keypads – Q5-Q86: System Settings • Press GO TO followed by the twodigit Question (01-86) PROGRAMMING SYSTEM CONFIGURATION • Q1 – Q4 Use the and arrows to move back and forth between SUB-QUESTIONS Use the and arrows to scroll through the different options PROGRAMMING SYSTEM CONFIGURATION • Q5 – Q86 Use the and arrows to move back and forth between QUESTIONS Use the and arrows to scroll through the different options PROGRAMMING Q1: RF SENSORS Select RF Sensor # (01-48) • Up to 48 wireless RF sensors can be used with each Control Panel. The options for each sensor are programmed with sub-questions. – – Begin by entering the RF sensor number or select it using the ← or → arrows. After selecting the sensor number, program the sensor details by using the ↑ and ↓ arrows to select each of the suboptions. Press the ↓ arrow to continue PROGRAMMING Q1: RF SENSORS Select RF Sensor (#) Type Default: Unused (00) • Each RF sensor needs to be assigned to a sensor type. The sensor type determines how and when the Control Panel responds to signals from the sensor. – Select the sensor type that matches the sensor’s function using the ← or → arrows, or enter the sensor type number directly on the keypad. PROGRAMMING Q1: RF SENSORS Select RF Sensor (#) Type Default: Unused (00) • SENSOR TYPES – – – – – – – – – – – – – – – (00) unused (01) exit/entry 1 (02) exit/entry 2 (03) perimeter (04) interior follower (05) day zone (06) 24-hour silent alarm (07) 24-hour audible alarm (08) 24-hour auxiliary alarm (09) 24-hour fire (10) interior with delay (14) 24-hour carbon monoxide (16) 24-hour fire with verification (23) no response type (24) silent burglary Press the ↓ arrow to continue PROGRAMMING Q1: RF SENSORS Select RF Sensor (#) Equipment Code Default: (0000) Other • The equipment code is a 4-digit code that is assigned to the model of sensor being used. The Control Panel will display a list of sensor models and their associated 4-digit equipment code. – Select the model of RF sensor being programmed for this sensor number using the ← or → arrows, or enter the equipment code number directly on the keypad. PROGRAMMING Q1: RF SENSORS Select RF Sensor (#) Equipment Code • SENSOR EQUIPMENT CODES – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – – (0000) other (0862) DW10-345 thin door/window contact (0863) DW20R-345 recessed door contact (0869) PIR1-345 PIR with pet immunity (0864) GB1-345 glass break detector (0895) SMKT2-345 GE smoke/heat detector (USA/Canada) (1058) SMKT3-345 2gig smoke detector (0872) SMKE1-345 smoke detector (USA) (0871) SMKE1-345C smoke detector (Canada) (0868) PANIC1-345 panic button remote (0860) CO1-345 CO detector (USA) (0859) CO1-345C CO detector (Canada) (1026) CO3-345 2gig CO detector (USA/Canada) (0873) TAKE-345 takeover module (0637) HW D/W “5816” (0470) HW R-D/W “5818MNL” (0533) HW PIR “5890” (0530) HW PIR “5894PI” (0519) HW Glass Break “5853” (0589) HW Smoke “5808W3” (0557) HW Heat Sensor “5809” (0624) HW Flood Sensor “5821” (0491) HW Panic Pendant “5802MN2” (0655) Existing door/window contact (0609) Existing motion detector (0475) Existing glass break detector (0616) Existing smoke detector (0692) Existing CO detector (0708) Existing heat sensor (0556) Existing flood/temp sensor (1061) GARAGE01 Resolution Products tilt sensor Press the ↓ arrow to continue PROGRAMMING Q1: RF SENSORS Select RF Sensor (#) Serial # Default: (0000000) • RF sensor serial #s can be manually entered or learned from the sensor. – – For manual entry, enter the sensor number that was logged for the sensor being programmed. Use the SHIFT button to access alpha characters. For automatic entry, press SHIFT, then press LEARN. The Control Panel will wait for a sensor transmission. Trigger the sensor being programmed and the Control Panel will beep four times and learn the sensor’s serial number. Press the ↓ arrow to continue PROGRAMMING Q1: RF SENSORS Select RF Sensor (#) Equipment Age Default: New (0) • The Control Panel can be used with new or existing RF sensors. – – If this RF sensor is new for the installation, leave the default of new (0). If this RF sensor is already installed, select existing (1). Press the ↓ arrow to continue PROGRAMMING Q1: RF SENSORS Select RF Sensor (#) Loop Number Default: (1) • 2GIG-DW10 door/window sensors have two inputs. Either or both sensor inputs can be used. – LOOP 1 • – An external normally closed hardwired input LOOP 2 • An internal magnetic contact Press the ↓ arrow to continue PROGRAMMING Q1: RF SENSORS Select RF Sensor (#) Dialer Delay Default: Enabled (1) • RF sensors can trigger the communicator immediately or after a delay. The delay time is set by the abort window dialer delay programming question Q-35 (the default delay is 30 seconds). – – The default (1) causes delayed dialing for this RF sensor number. For immediate dialing for this RF sensor number, select disabled (0). • NOTE: This default can be changed without affecting SIA CP01 compliance. Press the ↓ arrow to continue PROGRAMMING Q1: RF SENSORS Select RF Sensor (#) Voice Descriptor • The voice descriptors are the words the Control Panel will announce for this RF sensor if this sensor is programmed for voice annunciation. – – – – – Press INSERT to place a word from the vocabulary into the data entry field. Use the ← or → arrows to scroll through the words, or enter the word’s 3-digit index number (see vocabulary table on Page 19). Press INSERT again for the next word. Up to five words are allowed. To move between words, press the FWD and BACK buttons. To remove a word, press DELETE. Press the ↓ arrow to continue PROGRAMMING Q1: RF SENSORS Select RF Sensor (#) Reports Default: Enabled (1) • RF sensors can trigger a report to the Central Station or not. – – The default (1) enables reporting for this RF sensor number. To prevent reporting for this RF sensor number, select disabled (0). Press the ↓ arrow to continue PROGRAMMING Q1: RF SENSORS Select RF Sensor (#) Supervised Default: Enabled (1) • When a sensor is set to supervised, the Control Panel will expect regular timed signals from this sensor or else a sensor supervisory trouble alert will occur. – – The default (1) allows supervision for this RF sensor. To turn off supervision for this RF sensor, select disabled (0). • NOTE: Portable sensors such as panic buttons should not be set as supervised if the sensor will be removed from the premises at times. Press the ↓ arrow to continue PROGRAMMING Q1: RF SENSORS Select RF Sensor (#) Chime Default: Disabled (0) • Each RF sensor can be set to sound a “ding-dong” chime and/or sound its voice descriptor when the sensor is triggered. – – The default (0) disables the chime for this RF sensor. If a chime and/or voice is required for this RF sensor, choose one of the other chime options: • RF SENSOR CHIME – (0) disabled – (1) voice only – (2) voice with ding-dong #1 – (3) ding-dong #2 – (4) voice with ding-dong #2 – (5) ding-dong #1 Press the ↓ arrow to continue PROGRAMMING Q1: RF SENSORS Summary of RF Sensor (#) • The summary page allows you to quickly look over the different settings you chose for that zone and make sure everything is correct. – – – If you need to adjust a setting, press EDIT CURRENT. If everything looks correct, you can press EDIT NEXT to move onto the next zone Press SKIP to move onto the next Question (WIRED ZONES.) Press SKIP to continue PROGRAMMING Q2: WIRED SENSORS Select Wired Sensor # (1 to 2) • The Control Panel can be programmed with up to two wired sensors. The wired sensors are hardwired contact loops connected to the loop input terminals on the Control Panel’s terminal strip. – WIRED SENSOR REPORTING CODES • Wired sensor #1 Reports as sensor #49 • Wired sensor #2 Reports as sensor #50 – NOTE: Wired sensors CANNOT be used for a CO or Fire Sensor loop Press the ↓ arrow to continue PROGRAMMING Q2: WIRED SENSORS Select Wired Sensor (#) Type Default: Unused (00) • Select the sensor type that matches the wired sensor’s function using the ← or → arrows or enter the sensor type number directly on the keypad. – SENSOR TYPES • • • • • • • • • • • • (00) unused (01) exit/entry 1 (02) exit/entry 2 (03) perimeter (04) interior follower (05) day zone (06) 24-hour silent alarm (07) 24-hour audible alarm (08) 24-hour auxiliary alarm (10) interior with delay (23) no response type (24) silent burglary Press the ↓ arrow to continue PROGRAMMING Q2: WIRED SENSORS Select Wired Sensor (#) Equipment Code Default: (0) • The wired sensor equipment code defines the sensor’s manufacturer and type. – Enter the 4-digit equipment code for the sensor Press the ↓ arrow to continue PROGRAMMING Q2: WIRED SENSORS Select Wired Sensor (#) Equipment Age Default: New (0) • The Control Panel can be used with new or existing wired sensors. – – If this wired sensor is new for the installation, leave the default of new (0). If this wired sensor is already installed, select existing (1). Press the ↓ arrow to continue PROGRAMMING Q2: WIRED SENSORS Select Wired Sensor (#) Normal State Default: Not Used (0) • The two hardwired loops can be wired for normally open (N/O) or normally closed (N/C) contacts, or for end-of-line (EOL) resistor. – WIRED SENSOR NORMAL STATE • • • • (0) not used (1) closed (2) open (3) end-of-line resistor Press the ↓ arrow to continue PROGRAMMING Q2: WIRED SENSORS Select Wired Sensor (#) Dialer Delay Default: Enabled (1) • Wired sensors can trigger the communicator immediately or after a delay. The delay time is set by the abort window dialer delay programming question Q-35 (the default delay is 30 seconds). – – The default (1) causes delayed dialing for this wired sensor number. For immediate dialing for this wired sensor number, select disabled (0). • NOTE: This default can be changed without affecting SIA CP01 compliance. Press the ↓ arrow to continue PROGRAMMING Q2: WIRED SENSORS Select Wired Sensor (#) Voice Descriptor • The voice descriptors are the words the Control Panel will announce for this wired sensor if this sensor is programmed for voice annunciation. – – – – – Press INSERT to place a word from the vocabulary into the data entry field. Use the ← or → arrows to scroll through the words, or enter the word’s 3-digit index number (see vocabulary table on Page 19). Press INSERT again for the next word. Up to five words are allowed. To move between words, press the FWD and BACK buttons. To remove a word, press DELETE. Press the ↓ arrow to continue PROGRAMMING Q2: WIRED SENSORS Select Wired Sensor (#) Reports Default: Enabled (1) • Wired sensors can trigger a report to the Central Station or not. – – The default (1) enables reporting for this wired sensor number. To prevent reporting for this wired sensor number, select disabled (0). Press the ↓ arrow to continue PROGRAMMING Q2: WIRED SENSORS Select Wired Sensor (#) Chime Default: Disabled (0) • Each wired sensor can be set to sound a “ding-dong” chime and/or sound its voice descriptor when the sensor is triggered. – – The default (0) disables the chime for this wired sensor. If a chime and/or voice is required for this wired sensor, choose one of the other chime options: • WIRED SENSOR CHIME – (0) disabled – (1) voice only – (2) voice with ding-dong #1 – (3) ding-dong #2 – (4) voice with ding-dong #2 – (5) ding-dong #1 Press the ↓ arrow to continue PROGRAMMING Q2: WIRED SENSORS Summary of Wired Sensor (#) • The summary page allows you to quickly look over the different settings you chose for that zone and make sure everything is correct. – – – If you need to adjust a setting, press EDIT CURRENT. If everything looks correct, you can press EDIT NEXT to move onto the next zone Press SKIP to move onto the next Question. (KEYFOBS) Press SKIP to continue PROGRAMMING Q3: KEYFOBS Select Fob # (1 – 8) • The Control Panel can be programmed with up to eight RF remote control key fobs. – RF KEY FOB REPORTING CODES • • • • • • • • RF key fob #1 Reports as sensor #51 RF key fob #2 Reports as sensor #52 RF key fob #3 Reports as sensor #53 RF key fob #4 Reports as sensor #54 RF key fob #5 Reports as sensor #55 RF key fob #6 Reports as sensor #56 RF key fob #7 Reports as sensor #57 RF key fob #8 Reports as sensor #58 Press the ↓ arrow to continue PROGRAMMING Q3: KEYFOBS Select Fob (#) Used Default: Unused (0) • Key fobs can be used with the Control Panel or not. – – The default (0) sets all key fobs as unused (0). To enable programming for this key fob, select used (1). Press the ↓ arrow to continue PROGRAMMING Q3: KEYFOBS Select Fob (#) Equipment Code Default: (0000) Other • The key fob equipment code defines the sensor’s manufacturer and type. – – – The default is (0000) other. Select (0866) KEY1-345 4-button keyfob remote for a 2GIG-KEY1 key fob remote. Select (0577) Existing keyfob remote for an existing key fob remote. • NOTE: Only 2GIG-KEY1 key fobs can be used with this system. Press the ↓ arrow to continue PROGRAMMING Q3: KEYFOBS Select Fob (#) Serial Number Default: 0000000 • Key fob serial numbers can be manually entered or learned from the fob. – – For manual entry, enter the fob number that was logged for the fob being programmed. Use the SHIFT button to access alpha characters. For automatic entry, press SHIFT, then press LEARN. The Control Panel will wait for a fob transmission. Trigger the fob being programmed and the Control Panel will learn the fob’s serial number. Press the ↓ arrow to continue PROGRAMMING Q3: KEYFOBS Select Fob (#) Emergency Key Default: Disabled (0) • Pressing the AWAY and DISARM buttons on a key fob at the same time for five seconds can trigger an emergency alarm. – – The default (0) disables the emergency function for this fob. To enable the emergency function for this fob, select one of the four options: • FOB EMERGENCY KEY FUNCTION – (0) disabled – (1) auxiliary alarm – (2) audible alarm – (3) silent panic – (4) fire Press the ↓ arrow to continue PROGRAMMING Q3: KEYFOBS Select Fob (#) Key 2 Can Disarm Default: Enabled (1) • Key fobs can be set to allow disarming the Control Panel with the fob’s DISARM button or not. If using a key fob as a stationary wall fob, it can be set to prevent someone from using it to disarm the system. – – The default (1) allows this fob to disarm the system. To not allow this fob to disarm the system, select disabled (0). Press the ↓ arrow to continue PROGRAMMING Q3: KEYFOBS Select Fob (#) Voice Descriptor Default: Keyfob (#) • The voice descriptors are the words the Control Panel will announce for this keyfob sensor for low battery announcements and log entries. – – – – – Press INSERT to place a word from the vocabulary into the data entry field. Use the ← or → arrows to scroll through the words, or enter the word’s 3-digit index number. Press INSERT again for the next word. Up to five words are allowed. To move between words, press the FWD and BACK buttons. To remove a word, press DELETE. Press the ↓ arrow to continue PROGRAMMING Q3: KEYFOBS Select Fob (#) Arm No Delay (Instant) Default: Disabled (0) • Key fobs can be set to arm the Control Panel with or without an Entry Delay. – – The default (0) sets this fob to arm the system with an Entry Delay. To set this fob to arm the system without an Entry Delay, select enabled (1). Press the ↓ arrow to continue PROGRAMMING Q3: KEYFOBS Select Fob (#) Key 4 Output Default: Disabled (0) • The key fob’s AUXILARY (*) button can be used to trigger the Control Panel’s open collector output. – – The default (0) disables this fob’s auxiliary button. To use this fob’s auxiliary button, select the output function. • FOB KEY 4 OUTPUT – (0) disabled – (1) toggle output – (2) momentary output Press the ↓ arrow to continue PROGRAMMING Q3: KEYFOBS Summary of Fob (#) • The summary page allows you to quickly look over the different settings you chose for that keyfob and make sure everything is correct. – – – If you need to adjust a setting, press EDIT CURRENT. If everything looks correct, you can press EDIT NEXT to move onto the next keyfob. Press SKIP to move onto the next Question (KEYPADS.) Press SKIP to continue PROGRAMMING Q4: KEYPADS Select RF Keypad # (1 – 4) • The Control Panel can be programmed with up to four RF remote control keypads or wireless touch screen keypads. – RF KEYPAD REPORTING CODES • RF Keypad #1 Reports as sensor #59 • RF Keypad #2 Reports as sensor #60 • RF Keypad #3 Reports as sensor #61 • RF Keypad #4 Reports as sensor #62 Press the ↓ arrow to continue PROGRAMMING Q4: KEYPADS Select RF Keypad (#) Used Default: Unused (0) • Keypads can be used with the Control Panel or not. – – The default (0) sets all keypads as unused (0). To enable programming for this keypad, select used (1). Press the ↓ arrow to continue PROGRAMMING Q4: KEYPADS Select RF Keypad (#) Equipment Code Default: (0000) Other • The RF keypad equipment code defines the sensor’s manufacturer and type. – – Select (0867) PAD1-345 wireless keypad for a 2GIG-PAD1 RF keypad. Select (1059) TS-1 wireless touchscreen keypad for a 2GIG-TS1 Wireless Touch Screen Keypad. • NOTE: The TS-1 wireless keypad is not for UL985 installations. Press the ↓ arrow to continue PROGRAMMING Q4: KEYPADS Select RF Keypad (#) Serial Number Default: 0000000 • Keypad serial numbers can be manually entered or learned from the fob. – – For manual entry, enter the keypad number that was logged for the fob being programmed. Use the SHIFT button to access alpha characters. For automatic entry, press SHIFT, then press LEARN. The Control Panel will wait for a keypad transmission. Trigger the keypad being programmed and the Control Panel will learn the keypad’s serial number. Press the ↓ arrow to continue PROGRAMMING Q4: KEYPADS Select RF Keypad (#) Serial Number Default: 0000000 • For 2GIG-TS1 Wireless Touch Screen Keypads press LEARN. The Control Panel will display “Pair with TS-1. Initiating learning process.” Press the TS1 keypad’s PAIR WITH PANEL button. Both the TS1 and the Control Panel will display “The learn operation succeeded” when complete. – – – The Control Panel will display “RF keypad (#1-4)” for keypad identification. The TS1 will display “Network ID: xxxx” which is the unique serial number identifying the specific keypad. Press OK on both the Control Panel and TS1 to continue. • NOTE: The Model 2GIG-TS1 wireless touch screen keypad will display “The security system is temporarily not operational” after learning the keypad. This is normal, and will be displayed anytime the Control Panel is in system configuration (programming) mode. Press the ↓ arrow to continue PROGRAMMING Q4: KEYPADS Summary of RF Keypad (#) • The summary page allows you to quickly look over the different settings you chose for that keypad and make sure everything is correct. – – – If you need to adjust a setting, press EDIT CURRENT. If everything looks correct, you can press EDIT NEXT to move onto the next keypad. Press SKIP to move onto the next Question (SETTINGS) Press SKIP to continue IMPORTANT QUESTIONS Q:8 Dialer (default 0) If the system you are installing is POTS primary or GSM back-up, you must enable Q:8 so the system will look for a POTS line. Q:11 Enter CS Phone # (no default) Here is where you would enter the Central Station Receiver line. Remember to check for prefixes that might be required to dial out (Q:9). Only necessary for POTS systems. Q:12 CS Account # (no default) Here is where you would enter the last 4 digits of your Central Station account #. Only necessary for POTS systems. Q:63 Phone Fail Detect (default 0) Again, if the system you are installing is POTS primary or GSM back-up, you must enable Q:63 so the system will look for a POTS line and then send a trouble signal if the line is lost. IMPORTANT QUESTIONS Q:43 Enter Installer Code (1561) Here is where you can change your installer code. Q:44 Lock Installer Programming (default 0) The installer programming lockout feature is provided to prevent takeovers. The Control Panel can be set To limit an installer’s access to programming questions after a period of 48 hrs. The 48 hr lockout timer Starts when the installer exits system configuration. 0 – unlimited full access (default) 1 – deny access to programming after 48 hrs 2 – limited access to programming after 48 hrs. Installer can view, but not change CS phone # or or account #, or change installer lock settings. Q:79 Select Z-Wave feature (default 1) Here is where you can enable Z-Wave and remote access settings. INSTALLER TOOLBOX RADIO STATUS The radio status option allows you to monitor your cell strength, the activity of the cell unit, its serial number, and other information. You can also run a cell phone test manually to check to make sure it is linked correctly to your Central Station. INSTALLER TOOLBOX RESTORING DEFAULTS You can choose to restore the system to its original default settings, or reset only the console or zones individually. INSTALLER TOOLBOX WALK TEST The Walk Test (Installer Toolbox) and System Test (Customer Toolbox) are identical. This will enable you, or the customer to trip the sensors to test the signal strength of the equipment and to make sure the components are installed correctly. This will not send a signal to your Central Station. INSTALLER TOOLBOX DISABLE SOUNDER By pressing “ok,” you will disable the sounder (siren) for 30 min. After that, It will automatically enable itself. Or you can manually enable the sounder with the same menu option. TAKEOVER MODULE SUPER SWITCH • Convert 8 hardwire zones into 8 wireless zones by utilizing the existing hardwire system. • Stack up to 6 Takeover Modules onto 1 GO!CONTROL system. • Take over dry contacts as well as powered zones. TAKEOVER MODULE SUPER SWITCH G PORT Common ground port “LO” wires from the existing system 12V PORT 12 VDC power from the existing systems AUX power ZONE PORTS “HI” wires from existing system TAKEOVER MODULE WIRING *Wiring order: 1) 2) 3) 12V BATT 4) Disconnect all power to existing hardwire system Completely wire the takeover module Connect back-up battery terminals (module and existing system) Reconnect the existing systems power supply DC (AUX) POWER LO WIRES *If not powered up in correct order, The system will show a low battery On each zone controlled by the Takeover module. HI WIRES EXISTING SYSTEMS AC POWER TAKEOVER MODULE PROGRAMMING Type: Equipment: Serial#: Age: Loop: Dialer Delay: Voice Descriptor: Reports: Supervised: Chime: entry/exit, perimeter, etc… 0873 TAKE-345 XXX-XXX1 for each zone after, add 1 to the last digit 1st zone – new each zone after - existing 1 (always) disabled (unless required) program accordingly enabled enabled (customer) XXX-XXX3 XXX-XXX2 XXX-XXX1 HOME SERVICES WHAT IS Z-WAVE? SYSTEM CONFIGURATION ADDING A Z-WAVE DEVICE CREATING SCENES CREATING RULES Z-STAT (CT30) HOME SERVICES WHAT IS Z-WAVE? Z-Wave is a next-generation wireless ecosystem that lets all your home electronics talk to each other, and to you, via remote control. It uses simple, reliable, low-power radio waves that easily travel through walls, floors and cabinets. Z-Wave control can be added to almost any electronic device in your house, even devices that you wouldn't ordinarily think of as "intelligent," such as appliances, window shades, thermostats and home lighting. • Z-Wave Is Simple – Z-Wave control is easily added to almost any device in minutes. Simply plug the device you want to control into a Z-Wave module, and "join" it to your Z-Wave network! • Z-Wave Is Modular – With Z-Wave, you can add as much or as little home control as you want over time. You can add Z-Wave to a device, a room, a floor or the entire home, according to your needs and desires. •Z-Wave Is Affordable – Unlike costly whole-home control systems that need special wiring and professional installation, Z-Wave is accessible and easy for the do-it-yourselfer •Z-Wave Is Powerful – Z-Wave's intelligent mesh networking 'understands" the present status of any enabled device, and gives you confirmation that your devices have received the automatic or manual control commands you want • Z-Wave Is Versatile – Z-Wave can be added to almost anything in your home that uses electricity, and gives you the power to control or monitor them from your home or away from home.• Z-Wave Is Intelligent – Z-Wave enabled devices can work together as a team. Have your garage door turn on your house lights when you come home. Have your door locks notify you when your children arrive home from school. Turn your downstairs lights off from upstairs. Create your own intelligent control "scenes" with Z-Wave! Z-Wave Z-Wave is a WIRELESS COMMUNICATION PROTOCOL using the 908.42 MHz frequency. • Simple, energy efficient, two-way communication • Easily control lights, thermostats, locks, etc. • Uses mesh network topology for increased network robustness and range • Used by over 200 companies to make a wide variety of products. Z-Wave & the Install • Most Z-Wave devices have a lineof-sight range of 30-40 feet. • Unfortunately, homes have walls, appliances, or other things that can interfere with the signal. • Using another Z-Wave device that repeats (like an Evolve lamp module) will relay the signal to the out of range device. • The more devices you add to your network, the more reliable your network becomes. HOME SERVICES PROGRAMMING Questions 79 – 82 in System configuration are required to be modified for The Home Services portion of the Go!Control panel to function. Below are the questions and their options. HOME SERVICES PROGRAMMING Q79 SELECT Z-WAVE FEATURE Defaulted as (1) Disabled, Visible (0) Disabled (the Home Services button is hidden globally) (1) Disabled, Visible (The Home Services button is visible and when user presses the Home Services button the panel will read: “The Home Services feature is not currently activated. To activate Home Services, please call your security provider. (2) Local fully enabled, remote access disabled (3) Local partially enabled, local rules disabled, remote control enabled HOME SERVICES PROGRAMMING Q80 SELECT Z-WAVE SWITCH CONTROL FEATURE Defaulted as (0) Disabled (0) Disabled (1) Enabled HOME SERVICES PROGRAMMING Q81 SELECT Z-WAVE THERMOSTAT CONTROL FEATURE Defaulted as (0) Disabled (0) Disabled (1) Enabled HOME SERVICES PROGRAMMING Q82 SELECT Z-WAVE DOOR LOCK CONTROL FEATURE Defaulted as (0) Disabled (0) Disabled (1) Enabled HOME SERVICES ADDING & REMOVING DEVICES Press SERVICES HOME SERVICES ADDING & REMOVING DEVICES Press TOOLBOX HOME SERVICES ADDING & REMOVING DEVICES Enter INSTALLER CODE HOME SERVICES ADDING & REMOVING DEVICES Press ADD/REMOVE DEVICES HOME SERVICES ADDING & REMOVING DEVICES HOME SERVICES ADDING & REMOVING DEVICES DISCOVERY SCREEN: PRESS AND RELEASE DEVICE BINDING SWITCH WHEN A DEVICE IS DISCOVERED, IT WILL SHOW THE MANUFACTURER AND THE NODE # HOME SERVICES ADDING & REMOVING DEVICES DISCOVERY SCREEN: PRESS AND RELEASE DEVICE BINDING SWITCH WHEN A DEVICE IS REMOVED IT WILL SHOW THAT IT HAS BEEN REMOVED HOME SERVICES RENAMING A DEVICE Press SWITCHES HOME SERVICES RENAMING A DEVICE Press DEVICE BAR HOME SERVICES RENAMING A DEVICE Press RENAME HOME SERVICES RENAMING A DEVICE KEYBOARD: USE THE KEYBOARD TO CUSTOM NAME THE DEVICE HOME SERVICES RENAMING A DEVICE KEYBOARD: USE THE KEYBOARD TO CUSTOM NAME THE DEVICE NOW THE STATUS SCREEN WILL SHOW THE DEVICE NAME RATHER THAN THE MANUFACTURER HOME SERVICES CREATING A SCENE Press SCENES HOME SERVICES CREATING A SCENE Press ADD SCENE HOME SERVICES CREATING A SCENE Name the Scene HOME SERVICES CREATING A SCENE Press ADD ACTION HOME SERVICES CREATING A SCENE Select a Device Type HOME SERVICES CREATING A SCENE Select The Action Press OK HOME SERVICES CREATING A SCENE List of Scenes HOME SERVICES CREATING A RULE Press RULES HOME SERVICES CREATING A RULE Press ADD RULES HOME SERVICES CREATING A RULE Select the EVENT Select the SCENE HOME SERVICES CREATING A RULE List of Rules HOME SERVICES CREATING A RULE ON ALARM.COM THERMOSTAT CT-30e WHY DO WE OFFER ONE? INSTALLATION STEPS NETWORK INCLUSION THERMOSTAT CT-30e The Z-Stat (CT-30e) Manufactured by Radio Thermostat Co Flawless integration with the CNTRL2 Panel Touch Screen Interface 10 month battery life Also has a “C” wire for powered applications THERMOSTAT WIRING Step 1 Cut all power to the HVAC system (turn off the breaker) Step 2 LABEL! LABEL! LABEL! There isn’t any wire color code with HVAC systems, so it is vital that you label the wires as you remove them from the existing thermostat. Step 3 Install your new 2GIG-Z-Stat by lining up your labeled wires with the ports. If some of your labeled wires do not correspond with any ports on the thermostat, see your installation guide for alternative labeling (p.17 +18.) Step 4 Power up the HVAC system. A good way to test if the thermostat is working is to manually turn on the fan. You will hear the fan kick on. USE THE INSTALLATION GUIDE INCLUDED WITH THE THERMOSTAT TO IDENTIFY WHAT TYPE OF HVAC SYSTEM YOU ARE WORKING WITH SO YOU CAN SET UP THE THERMOSTAT CORRECTLY. THERMOSTAT NETWORK INCLUSION Step 1 Make sure Questions 79 and 81 are enabled Step 2 Now, go to ADD DEVICES and link the thermostat. Press the MENU button on the right, then the MATE touch screen button on the left twice. Wait for the ADD DEVICES page to upload all the information from the thermostat, this may take a little bit (30 sec or so). THERMOSTAT NETWORK INCLUSION Step 1 Make sure Questions 79 and 81 are enabled Step 2 Now, go to ADD DEVICES and link the thermostat. Press the MENU button on the right, then the MATE touch screen button on the left twice. Wait for the ADD DEVICES page to upload all the information from the thermostat, this may take a little bit (30 sec or so). THERMOSTAT NETWORK DISCOVERY Step 3 Allow device to fully query and upload Step 4 Add to scenes or rules 2GIG Technical Support 855.2GIGTEC 855.244.4832 HRS of Operation Mon – Fri: 8am – 7pm (MST) Sat: 8am – 4pm (MST) Alarm.com Tech Support 9am – 7pm (EST M-F) Radio Thermostat Tech Support 9am – 12am (EST 7 days/week) 866.834.0470 888.207.6317 [email protected] Andrew Curtis Director of Customer Support [email protected] o: 801-221-9162 c: 801-874-4085