Gps Pulse Ble - Sg013 Introduction

Transcript

GPS Pulse BLE - SG013 GPS Pulse BLE Optical HRM Watch Introduction Thank you for purchasing the GPS Pulse BLE (BLE 4.0) Optic HRM w atch. This product uses an Electro-optical technology to sense the heart beat. It has an electro-optical cell to sense the volume of blood under your skin. Wear the watch properly in your forearm: Fasten the watch snugly so that the optical sensor makes a tight contact with your skin. The tighter you can wear the watch the better. Wear the watch not on your wrist bone but higher on your forearm. If the Heart rate data displayed in the device is not stable or erratic, try to move the device along your forearm within the best wearing position as illustrated. Know your Watch: This product has also a GPS function with the following main modes as you press S7: TIME, RUN, HRM, CHRONO, TIMER, DATA, ALARM and SET. Push button main function: Important note: Before starting your exercise You may need to tighten the strap. After sweating, you have to tighten the watch again for accurate measurement. Make sure the heart rate reading is already stable. Minimize excessive wrist movement while the HR is in use. WARNING: Consult your doctor before you begin a new exercise program. This is important for persons with pre-existing health problems or persons who have taking medication regularly. This watch provides heart rate measurements. However, this is not a medical device. This watch may affect pacemakers. If you have any concerns, consult your doctor before using this watch. Over exercising may result in serious injury or death. If you feel faint, if you become short of breath, or if you experience pain while doing an exercise, stop immediately and cool down. Caring for your Watch: Clean your Watch with a dampened cloth preferably with mild detergent solution. Wipe dry using a dry cloth. Do not use chemical cleaners and solvents that may damage plastic components. Do not store your Watch to prolonged exposure to extreme temperatures as this may result to permanent damage to your unit. GPS Pulse BLE - SG013 Notes: Charging Battery to PC: If pairing is successful, the watch will display “PAIR OK”. If pairing is not successful, the watch will display “ PAIR FAIL” after 1 minute. In any TIME screen, press and hold S11 button to turn off the Bluetooth. It is recommended to fully charge the watch before first use and never to hit empty. Please immediately charge when the battery level is at 20% to maximize the battery life and must be charged once a month even if it is not used. Plug your USB cable to your PC Align the charging clip with the contacts on the back of the Watch. Connect the charging clip securely to the watch. Note: Please thoroughly dry the charging contacts and surrounding area to ensure proper electrical contact and prevent corrosion. Battery low condition: You cannot turn ON the GPS when the battery is low. You need to recharge the battery in order to use the GPS again. The watch will display “BATT ERY LOW” 2) Open the App on your Smartphone to pair. 3) Tap “LINK DEVICE”. Select Bluetooth ID (ex. GPS Pulse C237) and tap “Done”. 4) Tap “Pair”. 6) Fill-in the User Name and your Email add. Then tap “Return” on the lower right side of the screen and tap “NEXT”. 5) 7) Caution: Prolonged water submersion may cause electronic shorting in the unit which may cause minor skin burn or irritation. How to pair the watch with Smartphone: 1) Press and hold S11 while in Time mode. The “ HOLD TO PAIR” appears followed by pairing ID screen. icon on the upper left side of the Setting MENU screen. Note: The User can set the following setting options such as Unit, User, etc. by tapping the setting sync icon (swipe up/down to view other setting options). Water immersion: This GPS Optic HRM watch, is designed to be water resistant up to 3 ATM. After submersion to water, please make sure to wipe dry and air dry the unit before using or charging. Water damage may occur if the buttons are pressed underwater Tap the Homepage 8) Tap “ HOME” and seconds later , the Home screen appears. Tap to select HR, etc. as shown. icon on the upper right side of the Home screen to Note: Tap the Data Sync sync your current data. How to Disconnect the Smartphone and the watch: 1) Tap the Homepage icon while in the Home screen. 2) Tap the “TAP TO DISCONNECT” on the bottom part of the screen. 3) Tap “Yes” to con rm and sign out. 4) Go to “SETTINGS” on your Smartphone. 5) Tap Bluetooth On. 6) Tap “Connected or Not Connected”. 7) Tap “Forget This Device”. 8) Tap “Forget Device” to con rm. 9) Tap to turn Off the Bluetooth. 10) Press and hold S11 button to turn OFF the watch Bluetooth. GPS Pulse BLE - SG013 Configure your Watch: Users can opt to set the Watch before use. Set the 12/24H by pressing S1/S11 and then press S5 to confirm. The watch will return to SET TIME screen. While in TIME mode, press S7 repeatedly to go to SET mode and set the following parameters: AUTO LAP, TIME, UNIT, USER, HRM, VIEW, NIGHT, CONTRAST, CHIME, ALARM, and TIMER. Press S1 or S11 to change the blinking parameter to set. Note: When you sync the watch with the Smartphone App, the watch time will sync with the Smartphone time. How to set the AUTOLAP: Press S5 while “AUTO LAP” is blinking. The autolap distance digit will start to blink. Press S1/S11 to change the setting. (Auto lap preset settings: 0.4, 1, 2, 3, 4, 5 & OFF) Press S5/S7 to confirm and set ALERT ON or OFF. Press S1/S11 to change the setting. Press S5/S7 to confirm. How to set the UNIT: Press S5 while “UNITS” is blinking. Press S1/S11 to change the unit (KM or Mi). Press S5/S7 to confirm. How to set USER details: The watch will take Auto Lap based on your Auto Lap preset settings. How to set the TIME: Press S5 while “TIME” is blinking. The Hour digit will start blinking. Set the Hour by pressing S1/S11 and then press S5 to confirm. Set the Minute by pressing S1/S11 and then press S5 to confirm. Set the Second by pressing S1/S11 and then press S5 to confirm. Set the Year by pressing S1/S11 and then press S5 to confirm. Set the Month by pressing S1/ S11 and then press S5 to confirm. Set the Day by pressing S1/ S11 and then press S5 to confirm. Press S5 while “USER” is blinking. “GENDER” will start to blink. Press S5 or wait for few seconds. “ MALE” will start to blink. Press S1/S11 to change the gender. Press S5/S7 to confirm and set the “AGE”. Press S5 or wait for few seconds. Age digits will start to blink. Press S1/S11 to change the age digits. Press S5/S7 to confirm and set the “WEIGHT”. Press S5 or wait for few seconds. Weight digits will start to blink. Press S1/S11 to change the weight digits. Press S5/S7 to confirm and set the “HEIGHT”. Press S5 or wait for few seconds. Height digits will start to blink. Press S1/S11 to change the height digits. Press S5/S7 to confirm. Note: User has the option to press S1/S11 to select/set while the blinking Gender, Age, Weight or Height. GPS Pulse BLE - SG013 How to set the VIEW You can change Line 1 and Line 3 display information for RUN mode. Press S5 while VIEW is blinking. Press S5 to select between Line 3 or Line 1 Press S5 to confirm selection. While Line 3 is blinking, Press S1/S11 to change the information displayed in Line 3. You can select from the following: Distance, Pace, Speed, Calorie, Clock, HRM and Chronograph. Press S5 to confirm and Line 1 will start to blink. Press S1/S11 to change the information to be displayed in Line 1. You can select from the following: Chronograph, Distance, Pace, Speed, Calorie, Clock and HRM. Press S5 to go back to Line 3 setting. Press S7 to exit. When you return back to RUN mode, the watch will now display the information in Lines1 & 3 you have selected. How to set the HRM: Press S5 while “HRM” is blinking. ZONE 1 will start to blink. Press S1/S11 to change the zone. There are 3 preset zones Press S5/S7 and the watch will display the LOWER limits of the selected zone. LOW limit digit will start to blink. Press S1/S11 to change the low limit value. Press S5/S7 to confirm. High limit digit will start to blink. Press S1/S11 to change the high limit value. Press S5/S7 to confirm. The watch will display ZONE ALERT ON or OFF. Press S1/S11 to change ON to OFF or vice versa Press S5/S7 to confirm. How to set the NIGHT mode function: Press S5 while “NIGHT” is blinking. The watch will display 10 seconds blinking. Press S1/S11 to change to 20 sec or NIGHT ON. While on 10 SEC or 20 SEC setting, Press S5/S7 to accept the setting and go back to NIGHT setting screen. While on NIGHT ON setting screen Press S5 to accept the ON setting. The watch will display the START TIME. Press S1/S11 to toggle between START TIME and END TIME. Press S5 or wait for few seconds to set the START TIME. Hour digit will start to blink. Press S1/S11 to change the hour setting. Press S5 to change the MINUTE. Minute digits will start to blink. GPS Pulse BLE - SG013 Press S1/S11 to change the minute setting. Press S5 to go back to START TIME setting screen. Press S1/S11 to set the END TIME. Hour digit will start to blink. Note: Follow the above procedure in setting the END TIME. How to set the LCD display CONTRAST: Press S5 while “CON-TRAST” is blinking. Contrast percentage will start to blink. Press S1/S11 to change to your desired value. LCD Contrast range is from 10 to 100%. Press S5/S7 to confirm. How to set the CHIME: Press S5 while “ CHIME” is blinking. Press S1/S11 to change ON or OFF. Press S5/S7 to confirm. How to set the ALARM: Night mode settings: 10 SECONDS – Press S5 will turn ON the Light for 10 seconds. 20 SECONDS – Press S5 will turn ON the Light for 20 seconds. NIGHT ON – Default Start Time / End Time for NIGHT ON setting is 5 PM to 7 AM. Following are the characteristics of NIGHT ON setting: o o o Start Time and END TIME for NIGHT ON setting can be changed in SET mode/ NIGHT. When the Night setting is ON, pressing any button within the Start Time / End Time will turn ON the EL for 10 seconds. Outside the Start time / End Time, only press S5 will turn ON the EL for 10 seconds. Press S5 while “ALARM” is blinking. AL-1 will start to blink. Press S1/S1 to toggle through Alarm 1 to alarm 5. Press S5 to set the selected Alarm number. The HOUR digit will start to blink. Press S1/S11 to change the hour digit. Press S5 to confirm and set the MINUTE digit. Press S1/S11 to change the minute digit. Press S5 to confirm and set the Alarm “ON” or “ OFF”. Press S1/S11 to change the setting. Press S5 to confirm and set the Chime” ON” or “OFF”. Press S1/S11 to change setting. Press S5 to confirm. GPS Pulse BLE - SG013 Acquire Satellite signals: In order to get the correct time of day and begin using your watch, you have to acquire the Satellite signals. It may take a few minutes to get the signals. Press S7 to search signal. Go outside to an open area away from tall buildings and trees. Orient the GPS antenna towards the sky for best reception. The antenna is located at the 12 o’clock position of the watch. Stand still and do not begin moving while locating the Satellites until the GPS signals are already received. If no Satellite signal is received, after approx. 10 minutes, the watch will go to Time mode. How to Turn ON the GPS: How to set the TIMER: Press S5 while “TIMER ” is blinking. The segment number 1 (SG-1) will start to blink. Press S1/S11 to change the segment number Press S5 to set the HOUR. The hour digit starts to blink. Press S1/S11 to change the digit. Press S5 to set the MINUTE. The minute digit starts to blink. Press S1/S11 to change the digit. Press S5 to set the SECONDS. The second digit starts to blink. Press S1/S11 to change the digit. Press S5 to confirm Following are the possible ways to turn On the GPS. Press S7 from Time mode to go to RUN mode. The watch will automatically search for GPS signal and once signal is received, it will go to “GPS GO” screen . Press S7 from Time mode to go to TIMER mode. The Watch will display the “GPS / INDOOR” selection screen. Select “GPS” by pressing S1 and press S5 to confirm. The watch will start searching for GPS signal and once signal is received, it will go to “GPS GO” screen . Press and hold S7 from any mode while GPS is initially OFF. The watch will display “GPS ON” and it will then automatically search for GPS signal. And once signal is received, it will go to “GPS GO” screen . How to turn OFF the GPS: Press and hold S7 from any mode while GPS is initially ON. The watch will display “GPS OFF”. GPS signals and its meaning: How to turn ON the HRM: Press S7 TIME mode to go to HRM mode. Or press and hold S5 to turn ON the HRM in any mode. GPS Pulse BLE - SG013 How to turn OFF the HRM: In any mode press and hold S5 button to turn Off the HRM. Go for an Activity: Using RUN mode: Press S7 to go to RUN mode. The watch will prompt you to GPS GO screen (if Satellite signal is received). If GPS signal is already received, the watch will skip the SEARCH screens. How to change views in RUN mode: How to START, take LAP, STOP, and SAVE: o o o o Press S1 to start, or re-start. Press S11 to take lap. The display will freeze for 10 seconds. Press S1 to stop. Press and hold S1 or press S11 to save your data. o o o Press S5 to change the information displayed in Line2 (middle row). Following are the information that you can display in line 2: HRM, Chrono, Distance, Pace, Speed, Calorie, and Clock. If HRM is OFF, the HRM value in the first screen will be replaced by PACE. GPS Pulse BLE - SG013 Using HRM mode: Press S7 to go to HRM mode. The watch will go to INDOOR screen. How to change views in HRM mode: o o Press S5 to change the information displayed in Line 3 (bottom row). Following are the information you can display in line 3: Calorie, In Zone, Distance, Pace, Speed, and Clock. How to START, STOP, and SAVE: o o o o Press S1 to start, or re-start. Press S11 to take lap. The display will freeze for 10 seconds. Press S1 to stop Press and hold S1 or press S11 to save your data Using CHRONO mode: Press S7 to go to CHRONO mode. The watch will go to INDOOR screen. How to START, take LAP, STOP, and SAVE: o o o o Press S1 to start, or re-start. Press S11 to take lap. The display will freeze for 10 seconds. Press S1 to stop. Press and hold S1 or press S11 to save your data. GPS Pulse BLE - SG013 Using TIMER mode: Press S7 to go to TIMER mode. The Watch will display the “GPS / INDOOR” selection screen. either “GPS or INDOOR” and press S5 to confirm. Press S1/S11 to select Please set the TIMERS (in SET mode) first before using this mode. The watch has 6 interval timers (SG-1 to SG-6) segment 1 to segment 6. The default values for all segments are 0:00:00. When a segment reaches zero, there will be a beep sound. The cycle will loop for 50 loops (LO1 to L50) and stop. If only 1 segment timer is set and the other segments are set to zero, only that segment will countdown and loop up to 50 loops. How to change views in CHRONO mode o o Press S5 to change the information displayed in Line 3 (bottom row). Following are the information you can display in line 3: HRM, Chrono, Distance, Pace, Speed, Calorie, and Clock. How to START, take LAP, STOP, and SAVE: o o o o Press S1 to start, or re-start. Press S11 to take lap. The display will freeze for 10 seconds. Press S1 to stop. Press and hold S1 or press S11 to save your data. GPS Pulse BLE - SG013 General Operations The Watch has the following main modes: Time, Run, HRM, Chronograph, Timer, Data, Alarm and Set modes. Press S7 to scroll through these modes. TIME mode Press S7 from SET mode to TIME mode. The watch will momentarily display TIME and then display Time 1 (T1) If there is no activity after 1 minute, the watch will go to power saving screen How to change views in TIMER mode: o o Press S5 to change the information displayed in Line 3 (bottom row). Following are the information you can display in line 3: HRM, Chrono, Distance, Pace, Speed, Calorie, and Clock. DATA mode How to enter DATA mode, view details, and delete Data: Press S7 to go to Data mode. The watch will momentarily display “DATA” and then the latest data file. If there is no data available, it will display “NO DATA”. Press S1 to scroll through the various data files. Press S5 to enter the selected data file. Press S1/S5 to forward view the details. o Start Time / End Time / Distance o CHRONO /Distance / Calorie o CHRONO / Ave Pace / Max Pace o CHRONO/ Ave Speed / Max Speed o Ave HRM/ Max HRM / In-Zone o Lap 1 up to last lap view VIEW / DEL / DELETE ALL sub menus (press S1 to select). GPS Pulse BLE - SG013 Press S7 to exit Note: Timer data views will not be shown if no Timer data. Deleting Data/ All Data: Enter data mode. Press S1 to select data to be deleted. Press S5 repeatedly until the VIEW / DELETE / DEL ALL screen appears. Press S1 to select VIEW / DELETE / DELETE ALL. Press and hold S5 to delete selected data if you select DELETE. Press and hold S5 again to delete all data if you select DEL ALL. GPS Pulse BLE - SG013 Data numbering system/ Legend: Battery: The device is powered by a built-in lithium-ion battery. It can be charged using the USB port and it takes 4-5 hours to fully charge the battery. For further details, please read on page 2 “Charging Battery to PC. Battery Life: Sample data number: D03-03 1031- 1 02 G D 03 03 10 31 1 02 G Data Total number of files File number counter Month Date Refer to Time 1 File number of the day GPS workout, H -for INDOOR workout ALARM mode The battery will last for 8.0 hrs typical in a single charge. But this will vary depending on Customer’s us e. Battery Replacement: The battery on this watch is not User replaceable and it is highly recommended to be done by an authorized service personnel only. Troubleshooting guide PROBLEM/ QUESTION I cannot get a GPS signal How to enter Alarm mode Press S7 to go to ALARM mode. Press S5 to view Alarm 1 to Alarm 5 and Chime. Press S1 to turn ON or OFF the Alarm and Chime. Press S7 to exit. Can I reset the Watch? Will my data and personal settings be lost after Watch reset? My heart rate data seems inaccurate. SOLUTION/ ANSWER Take your GPS Watch outdoors and away from trees and tall buildings. Remain stationary and try acquiring the Satellite signal again. Be sure that the antenna (6 o’clock position) is pointing towards the sky for better signal reception. You can reset the Watch by pressing S1, S5, S7, and S11 together. The date and time will be reset to default values. You can set it again manually or automatically thru GPS. Your data and personal settings are saved in the flash memory and will not be lost after Watch reset. - If the Heart rate data displayed in the watch is not stable or erratic, try to move the watch along your forearm within the best wearing position as illustrated in page 1. - Your skin should be no SCARS or any other object in your skin that will interfere with the sensor. - The heart rate is taken directly through your skin to the watch sensor, so it is very important that there are no obstructions that will interfere with the transmission of the Heart rate data. - Try to wear the watch on your other wrist.