Transcript
NUMBER
TYPE
GS-12-1328
Product Specification
TITLE
PAGE
REVISION
1 of 12 AUTHORIZED BY
SFP+ LR Transceiver
B DATE
Ling.Wang
7 Aug 2015
CLASSIFICATION
UNRESTRICTED
T
he 10136338-001 SFP+ transceiver is intended for 10km reach service form 9.95Gb/s to 10.5Gb/s 1310nm single mode high-speed communications equipment where low-cost, extraordinary performance and reliability are essential. It consumes low power, operates from a 3.3V DC power supply and is offered in the commercial and industrial temperature ranges. They are compliant with IEEE802.3ae 10GBASE-LR/LW , SFF-8431 and SFF-8432. The low jitter and low bit error rate optical assembly features a 1310nm DFB laser transmitter and PIN/TIA receiver. It incorporates the SFP+ MSA LVTTL Loss of Signal (Rx_LOS), Tx Fault (Tx_FAULT), MOD_ABS and Tx Disable (Tx_DIS) monitor and control functions and the SFF-8472 compliant digital diagnostic monitor feature. The differential AC coupled Tx and Rx data interfaces are CML compatible. The device is Class I laser safety compliant.
Applications • 10G BASE-LR/LW 10G Ethernet • CPRI
+
Features • LC Duplex optical interface • Maximum link length of 10km • 9.95Gb/s to 10.5Gb/s • • • • • • • •
3.3 V power supply
Low DC power consumption 2x10 SFP+ MSA compliant package Hot swappable High performance 1310 nm DFB laser High sensitivity PIN/TIA optical receiver Single Mode operation BER < 1X10-12
•
Case Operating temperature ranges: 0 to 70ºC Data and Control Interfaces: • Tx Data CML/AC Coupled • Rx Data CML/AC Coupled • Tx_DIS LVTTL • Tx_FAULT LVTTL • Rx_LOS LVTTL • MOD_ABS LVTTL • 2-wire I2C data bus • RoHS 6 compliance •
Copyright © 2011 FCI Deutschland GmbH. FCI Deutschland GmbH reserves the right to make changes to this document at any time without notice. Information in this document is believed to be reliable. However, no responsibility is assumed for possible inaccuracy or omission.
PDS: Rev :B
STATUS:Released
Printed: Aug 07, 2015
NUMBER
TYPE
GS-12-1328
Product Specification
TITLE
PAGE
REVISION
2 of 12
B
AUTHORIZED BY
SFP+ LR Transceiver
DATE
Ling.Wang
7 Aug 2015
CLASSIFICATION
UNRESTRICTED
Recommended Operating Conditions Parameter
Min
Typ
Case Operating Temperature
Symbol Tcase
0
DC Supply Voltage
VCC
3.135
IIN
-
Module Supply Current
Max
Units
25
70
ºC
-
3.465
V
-
350
mA
Notes
Ordering Information Part Number
Case Operating Temperature
10136338-001
0 to 70ºC
Absolute Maximum Ratings (EXCEEDING THESE RATINGS MAY CAUSE IRREVERSIBLE DAMAGE TO THE DEVICE) Parameter
Symbol
Min
Max
Units
Notes
Storage Temperature
Tstg
-40
+85
ºC
Case Operating Temperature (Commercial)
TO
0
+70
ºC
Relative Humidity - Storage
RHS
0
95
%
Relative Humidity - Operating
RHO
0
85
%
DC Supply Voltage
VCC
0
3.6
V
Symbol
Min
Typ
Max
Units
Differential Data input Swing
VIN
180
-
700
mV
Tx Differential Input Impendence
ZIN
-
100
-
Ω
Transmitter Disable Voltage
VD
2.0
-
Vcc+0.3
V
VEN
0
-
0.8
V
Exceeding the Absolute Maximum Ratings may cause irreversible damage to the device. The device is not intended to be operated under the condition of simultaneous Absolute Maximum Ratings, a condition which may cause irreversible damage to the device.
Transmitter Electrical Characteristics Parameter
Transmitter Enable Voltage
Notes
Copyright © 2011 FCI Deutschland GmbH. FCI Deutschland GmbH reserves the right to make changes to this document at any time without notice. Information in this document is believed to be reliable. However, no responsibility is assumed for possible inaccuracy or omission.
PDS: Rev :B
STATUS:Released
Printed: Aug 07, 2015
NUMBER
TYPE
GS-12-1328
Product Specification
TITLE
PAGE
REVISION
3 of 12
B
AUTHORIZED BY
SFP+ LR Transceiver
DATE
Ling.Wang
7 Aug 2015
CLASSIFICATION
UNRESTRICTED Receiver Electrical Characteristics Parameter
Symbol
Min
Typ
Max
Units
Differential Data Output Swing
VOUT
300
-
850
mV
Rx Differential Output Impendence
ZOUT
-
100
-
Ω
LOS Assert Voltage
VLOSA
2.4
-
Vcc
V
LOS De-assert Voltage
VLOSD
VEE
-
VEE+0.4
V
Notes
Transmitter Optical Specification Parameter
Symbol
Min
Transmitter Laser Type
Typ
Max
Units
1310nm DFB
Optical Modulation Amplitude (OMA)
POMA
-5.2
-
-
dBm
Average Output Power
POUT
-8.2
-
+0.5
dBm
Average Output Power (Laser Off)
POFF
-
-
-30
dBm
λ
1260
-
1355
nm
Wavelength
∆λ
-
-
1
nm
SMSR
30
-
-
dB
Extinction ratio
ER
3.5
-
-
dB
Dispersion Penalty
DP
-
-
3.2
dB
Relative Intensity Noise
RIN
-
-
-128
dB/Hz
ORLT
-
-
12
dB
Spectral Line RMS Width @ -20dB Side Mode Suppression Mode
Optical Return Loss Tolerance Transmitter Output Eye
Notes
IEEE 802.3ae Compliant
ITU-T G.691/IEEE802.3ae
Copyright © 2011 FCI Deutschland GmbH. FCI Deutschland GmbH reserves the right to make changes to this document at any time without notice. Information in this document is believed to be reliable. However, no responsibility is assumed for possible inaccuracy or omission.
PDS: Rev :B
STATUS:Released
Printed: Aug 07, 2015
NUMBER
TYPE
GS-12-1328
Product Specification
TITLE
PAGE
REVISION
4 of 12 AUTHORIZED BY
SFP+ LR Transceiver
B DATE
Ling.Wang
7 Aug 2015
CLASSIFICATION
UNRESTRICTED
Receiver Optical Specifications Parameter
Symbol
Min
Receiver Type
Typ
Max
Units
Conditions / Notes
PIN/TIA λ
1260
-
1600
nm
PIN
-
-
-14.4
dBm
BER<10-12, PRBS 231-1
Received Sensitivity (OMA)
PIN(OMA)
-
-
-12.6
dBm
BER<10-12, PRBS 231-1
Optical Power Overload
PIN(SAT)
0.5
-
-
dBm
RFL
-
-
-12
dB
PA
-30
-
-
dBm
Wavelength Received Sensitivity
Receiver Reflectance Rx_LOS of Signal Assert Rx_LOS of Signal De-assert
PD
-
-
-17
dBm
Rx_LOS of Signal Hysteresis
PHy
0.5
-
5
dB
Parameter
Symbol
Min
Typ
Max
Units
Data rate
BR
9.95
9.953
10.5
Gb/s
General Optical Parameter
Bit Error Rate
BER
-
-
Maximum Supported Link Length
L(MAX)
-
-
-12
PRBS 231-1
10
10
Notes
km
Copyright © 2011 FCI Deutschland GmbH. FCI Deutschland GmbH reserves the right to make changes to this document at any time without notice. Information in this document is believed to be reliable. However, no responsibility is assumed for possible inaccuracy or omission.
PDS: Rev :B
STATUS:Released
Printed: Aug 07, 2015
NUMBER
TYPE
GS-12-1328
Product Specification
TITLE
PAGE
REVISION
5 of 12
SFP+ LR Transceiver
AUTHORIZED BY
B DATE
Ling.Wang
7 Aug 2015
CLASSIFICATION
UNRESTRICTED
Electrical Interface
10136338-001
Copyright © 2011 FCI Deutschland GmbH. FCI Deutschland GmbH reserves the right to make changes to this document at any time without notice. Information in this document is believed to be reliable. However, no responsibility is assumed for possible inaccuracy or omission.
PDS: Rev :B
STATUS:Released
Printed: Aug 07, 2015
NUMBER
TYPE
GS-12-1328
Product Specification
TITLE
PAGE
REVISION
6 of 12 AUTHORIZED BY
SFP+ LR Transceiver
B DATE
Ling.Wang
7 Aug 2015
CLASSIFICATION
UNRESTRICTED
PIN Assignment P in 2 0
T O P V IE W OF BOARD P in 1 1
P in 1 0
B O T T O M V IE W OF BOARD P in 1
Copyright © 2011 FCI Deutschland GmbH. FCI Deutschland GmbH reserves the right to make changes to this document at any time without notice. Information in this document is believed to be reliable. However, no responsibility is assumed for possible inaccuracy or omission.
PDS: Rev :B
STATUS:Released
Printed: Aug 07, 2015
NUMBER
TYPE
GS-12-1328
Product Specification
TITLE
PAGE
REVISION
7 of 12 AUTHORIZED BY
SFP+ LR Transceiver
B DATE
Ling.Wang
7 Aug 2015
CLASSIFICATION
UNRESTRICTED
PIN Description PIN
Symbol
Name/Description
Note
1
VEET
Transmitter Ground
1
2
TFAULT
3
TDIS
Transmitter Fault. Transmitter Disable. Laser output disabled on high.
2
4
SDA
2-wire Serial Interface Data Line (MOD-DEF2)
5
SCL
2-wire Serial Interface Clock (MOD-DEF1)
6
MOD_ABS
Module Absent, connected to VEET
7
RS0
Rx Rate Select: NOT implement
3
8
Rx_LOS
Loss of Signal indication. Logic 0 indicates normal operation.
2
9
RS1
Tx Rate Select: NOT implement
3
10
VEER
Receiver Ground
1
11
VEER
Receiver Ground
1
12
RD-
Receiver Inverted DATA out.
4
13
RD+
Receiver Non-inverted DATA out.
4
14
VEER
Receiver Ground
1
15
VCCR
Receiver Power Supply
16
VCCT
Transmitter Power Supply
17
VEET
Transmitter Ground
1
18
TD+
Transmitter Non-Inverted DATA in.
5
19
TD-
Transmitter Inverted DATA in.
5
20
VEET
Transmitter Ground
1
Notes 1. 2. 3. 4. 5.
Module ground pins VEET and VEER are isolated from the module case and chassis ground within the module. Shall be pulled up with 4.7k-10k ohms to a voltage between 3.15V and 3.6V on the host board. The pins are pulled low to VEET with a >30k resistor in the module. The 100Ohms differential Rx Data output is internally AC coupled and terminated. The 100Ohms differential Tx Data input is internally AC coupled and terminated.
Copyright © 2011 FCI Deutschland GmbH. FCI Deutschland GmbH reserves the right to make changes to this document at any time without notice. Information in this document is believed to be reliable. However, no responsibility is assumed for possible inaccuracy or omission.
PDS: Rev :B
STATUS:Released
Printed: Aug 07, 2015
NUMBER
TYPE
GS-12-1328
Product Specification
TITLE
PAGE
REVISION
8 of 12
B
AUTHORIZED BY
SFP+ LR Transceiver
DATE
Ling.Wang
7 Aug 2015
CLASSIFICATION
UNRESTRICTED I2C Memory Map (Page A0 HEX, Unlisted Fields are Blank / Empty) IIC Addr
Size
Name
Description
0
1
Identifier
SFP
03
Values (HEX)
1
1
Extended Identifier
Extended Identifier
04 07
2
1
Connector
Connector Type = LC
3-10
8
Transceiver
10G Base LR
11
1
Encoding
Encoding Type = 64/66B
06
12
1
BR, Nominal
Nominal Bit Rate 10.3Gb/s
67
13
1
Reserved
Reserved
00
14
1
Length(9µm)-km
10km Link Length in Kilometers / SMF
0A
15
1
Length (9µm)-100m
10km Link Length in Hundreds of Meters / SMF
64
16
1
Length (50µm)-10m
50-micron MMF Link Length = N/A
00
17
1
Length (62.5µm)-10m
62.5-micron MMF Link Length = N/A
00
18
1
Length (Copper)
Copper Link Length = N/A
00
19
1
Reserved
Reserved
00
20-35
16
Vendor name
36
1
Reserved
37-39
3
Vendor OUI
SFP Vendor IEEE Company ID
40-55
16
Vendor PN
The Part number in the Ordering Information
56-59
4
Vendor Revision Number
Programmed by Factory
60-61
2
Wavelength
Laser Wavelength = 1310nm
62
1
Reserved
Reserved
63
1
CC_BASE
Check sum of bytes 0-62
64-65
2
Transceiver Options
66
1
BR, max
10%
0A
67
1
BR, min
10%
0A
68-83
16
Vendor SN
Programmed by Factory
Programmed by Factory
84-91
8
Date code
Year,Month,Day
Programmed by Factory
92
1
Diagnostic Monitoring Type
Compliant with SFF-8472 V10.2 Internally Calibrated Received power measurement type-Average Power
68
93
1
Enhanced Options
1. Optional Alarm/Warning Flags Implemented 2. Soft Rx_LOS Monitor 3. Soft Tx_FAULT Monitor
B0
94
1
SFF-8472 Compliance
SFF 8472 Revision 10.2 Implemented
20 00 00 00 00 00 00 00
FCI MergeOptics
ASCII Format
Reserved
00 00 0A 0D ASCII Format Programmed by Factory 05 1E 00 Programmed by Factory
1. Rx_LOS 2. Tx_FAULT 3. Tx_DIS
00 1A
03
95
1
CC_EXT
Check sum of bytes 64-94
Programmed by Factory
96-127
32
Vendor Specific
Vendor Specific EEPROM
Programmed by Factory
Copyright © 2011 FCI Deutschland GmbH. FCI Deutschland GmbH reserves the right to make changes to this document at any time without notice. Information in this document is believed to be reliable. However, no responsibility is assumed for possible inaccuracy or omission.
PDS: Rev :B
STATUS:Released
Printed: Aug 07, 2015
NUMBER
TYPE
GS-12-1328
Product Specification
TITLE
PAGE
REVISION
9 of 12
B
AUTHORIZED BY
SFP+ LR Transceiver
DATE
Ling.Wang
7 Aug 2015
CLASSIFICATION
UNRESTRICTED 128-255
128
Vendor Specific
Vendor Specific
Programmed by Factory
A2 (hex) 8472 Digital Diagnostic Table - Summary of Parameters in the A2 (hex) Parametric Table The data in the parameter tables are compared with the data in the measured data tables in order to create a warning or alarm status bit The Warning or Alarm bit is set when the parameter drops below or exceeds the Low or High values stored in memory.
SFF-8472 Rev 9.3 A2 (HEX) Address Table for Alarm and Warning Data Alarm Threshold Data 8472 Parameter
High Value
Warning Threshold Data
Low Value
High Value
Low Value MSB LSB
Measured Values
Alarm Bit (Set) Address + Position
Warning Bit (Set) Address + Position
MSB
LSB
MSB
LSB
MSB
LSB
MSB
LSB
High
Low
High
Low
Temperature
00
01
02
03
04
05
06
07
96
97
112 (7)
112 (6)
116 (7)
116 (6)
Vcc
08
09
10
11
12
13
14
15
98
99
112 (5)
112 (4)
116 (5)
116 (4)
Tx Bias
16
17
18
19
20
21
22
23
100
101
112 (3)
112 (2)
116( 3)
116 (2)
Tx Output
24
25
26
27
28
29
30
31
102
103
112 (1)
112 (0)
116 (1)
116 (0)
Rx Input
32
33
34
35
36
37
38
39
104
105
113 (7)
113 (6)
117 (7)
117 (6)
Copyright © 2011 FCI Deutschland GmbH. FCI Deutschland GmbH reserves the right to make changes to this document at any time without notice. Information in this document is believed to be reliable. However, no responsibility is assumed for possible inaccuracy or omission.
PDS: Rev :B
STATUS:Released
Printed: Aug 07, 2015
NUMBER
TYPE
GS-12-1328
Product Specification
TITLE
PAGE
REVISION
10 of 12
SFP+ LR Transceiver
AUTHORIZED BY
B DATE
Ling.Wang
7 Aug 2015
CLASSIFICATION
UNRESTRICTED RECOMMENDED PCB LAYOUT
RECOMMENDED FRONT PANEL LAYOUT OPENING FOR LC
Copyright © 2011 FCI Deutschland GmbH. FCI Deutschland GmbH reserves the right to make changes to this document at any time without notice. Information in this document is believed to be reliable. However, no responsibility is assumed for possible inaccuracy or omission.
PDS: Rev :B
STATUS:Released
Printed: Aug 07, 2015
NUMBER
TYPE
GS-12-1328
Product Specification
TITLE
PAGE
REVISION
11 of 12
SFP+ LR Transceiver
B
AUTHORIZED BY
DATE
Ling.Wang
7 Aug 2015
CLASSIFICATION
UNRESTRICTED Mechanical Dimensions
Dimensions are mm Tolerance +/-0.1mm
EYE SAFETY
REQUIRED LABEL AND LASER EMISSION
The transceiver is a Class 1 eye-safe device according to FDA 21CFR1040.10 and 1040.11, IEC 60825-1 and IEC 60825-2.
This device is labeled in accordance with FDA and IEC requirements for laser safety.
ELECTROMAGNETIC INTERFERENCE (EMI), IMMUNITY AND PRODUCT SAFETY
REQUIRED LABEL
The transceiver is ESD safe (electrical pins) when tested according to MIL-STD-883, Method 3015.4 and ESD safe (optical connector) when tested according to IEC 61000-4-2. The device is immune to strong RF fields when tested in accordance with IEC 610004-3. The device complies with (US) FCC, Part 15, Subpart J; (Europe) CENELEC EN 55022; (Canada) Class B (CISPR22A); and (Japan) VCCI Class 1. The device has been designed to conform to product safety requirements including UL1950, CSA 22.2, and IEC 60950, and has been designed to meets the flammability requirements of UL94.
Copyright © 2011 FCI Deutschland GmbH. FCI Deutschland GmbH reserves the right to make changes to this document at any time without notice. Information in this document is believed to be reliable. However, no responsibility is assumed for possible inaccuracy or omission.
PDS: Rev :B
STATUS:Released
Printed: Aug 07, 2015
NUMBER
TYPE
GS-12-1328
Product Specification
TITLE
PAGE
REVISION
12 of 12
B
AUTHORIZED BY
SFP+ LR Transceiver
DATE
Ling.Wang
7 Aug 2015
CLASSIFICATION
UNRESTRICTED Complies with 21 CFR 1040.10 and 1040.11
Class 1 Laser Device
NOTICE The factory has made all adjustments to this device prior to shipment. No adjustments or modifications to the device are required or permitted. Any adjustment, modification or tampering of the device voids the product warranty. The US Food and Drug Administration may consider that any adjustment or modification to this device is an act of manufacturing and therefore will require that the device be recertified in accordance with 21 CFR 1040.10 .
LASER RADIATION INFORMATION Wavelength
1310nm
FDA Total Pout: 7mm aperture at 20cm distance
< 790µwatts
IEC Total Pout: 7mm aperture at 14cm distance
< 10,000µwatts
Beam Divergence
17.25º
Copyright © 2011 FCI Deutschland GmbH. FCI Deutschland GmbH reserves the right to make changes to this document at any time without notice. Information in this document is believed to be reliable. However, no responsibility is assumed for possible inaccuracy or omission.
PDS: Rev :B
STATUS:Released
Printed: Aug 07, 2015
