Transcript
Spacemaker Dishwasher Dimensions (Pub. 1-G003 pg. 132B) May 12, 1993
GSM2260N GE Spacemaker Under-the-Sink Dishwasher ®
DW PLUMBING/ELECTRICAL ROUGH-IN (IN INCHES)
Dimensions and Installation Information (in inches) Note: Undersink dishwashers can be installed only under sinks and not under other appliances. Plumbing—Hot Water Only: Use 3/8" O.D. copper tubing or 1/2" O.D. plastic tubing minimum inlet line. Water valve has 3/8" internal threads. Hand cut-off valve is recommended.
FRONT VIEW Plumbing and wiring must enter within this area from either side, 4 rear or bottom
Electrical: Fuse circuit with 15 amp or 20 amp standard fuse or circuit breaker. Total amp load is 8.6. Dishwasher operates on 120V, 60HZ power, Two-wire cable (14 Ga. Min.) with ground must be installed. Specifications: Inlet water temperature recommended—minimum 120°F at dishwasher. Inlet water pressure required—15 to 120 lbs./sq. inch. Note: All rough-in, both plumbing and electrical, must be completed before the dishwasher is installed. All plumbing and electrical work must be in accordance with local codes.
6 2" From cabinet
Cold Hot
19" From Cable 24" wall from wall
2" From floor
Ground Black (line) White (neutral)
3
For answers to your Monogram,® GE Profile™ or GE® appliance questions, visit our website at geappliances.com or call GE Answer Center® service, 800.626.2000. Listed by Underwriters Laboratories
Specification Created 10/07
350512
10" from cabinet
GSM2260N GE Spacemaker® Under-the-Sink Dishwasher Note: A close-fitting elbow or special shallow sink strainer is necessary to provide clearance between sink drain and dishwasher. Dishwasher furnished with 1/2" I.D. drain hose, 78" long. If using copper tubing, 2" length of 1/2" I.D. rubber hose must be provided to connect copper tubing to pump outlet. Disposer should have 7/8" I.D. dishwasher drain connector.
Rough-In for Installation with Disposer Dimensions (in inches) Waste air gap To air gap
Directional flow tee
FRONT VIEW Drain connection 4 1-1/2" MAX. dia. hole
Waste tee or disposer Remove hopper plug before connecting dishwasher drain
12" From wall
6 10" from cabinet
6" Double-bowl stainless steel sink
Sink strainer assembly
GFC290/300/700 Disposall® unit
Countertop 25" deep 1-1/2" thick 1-1/2" Close elbow
1-1/2" Directional flow tee
Spacemaker® dishwasher
Cold water Hot water Valve to shut off water to dishwasher
Dishwasher water inlet valve Electrical junction box (on dishwasher)
Allow a 5" radius to prevent kinking
Sink strainer assembly
GFC290/300/700 Disposall® unit
Cold water Hot water Valve to shut off water to dishwasher
Rear View Plumbing Arrangement Dimensions (in inches)
Hot water supply to dishwasher Dishwasher drain hose
6" Double-bowl stainless steel sink
1-1/2" Directional flow tee
Allow a 5" radius to prevent kinking
Countertop 25" deep 1-1/2" thick 1-1/2" Close elbow
Spacemaker® dishwasher
Hot water supply to dishwasher Dishwasher drain hose
Dishwasher water inlet valve Electrical junction box (on dishwasher)
Listed by Underwriters Laboratories
Specification Created 10/07
350512
installer at time of installation.
GSM2260N GE Spacemaker® Under-the-Sink Dishwasher Wall
Cabinet Rough-In Dimensions (in inches) Cabinet Rough-In Note: Either single- or double-bowl sink may be used, centered or offset, as shown in the front view illustration. The 20-1/2" maximum dimension from wall to front of sink bowl must be accurate if dishwasher is to fit properly under sink. Water lines to sink faucet and drain from sink can be run through area “A.”
Countertop 1-1/2" MIN. thick
If the sink bowl is more than 20-1/2" maximum specified distance form the wall, or if the base cabinet is less than the 24" minimum depth from the wall, a gap between the tub front flange and the front of the base cabinet may result.
to Either single- or double-bowl si sink flange shown in the front view illustrat 10-1/4" MAX. singleor be doub A Plumbing to front ofEither sink bowl must ac depth 6" MAX. 1-1/4" shown inlines the front vie under sink. Water to sink 10-1/4" MAX. 7-1/2 MIN. I.R. A Plumbing to front sinkWATER bowl m depth through area “A.”ofHOT 1-1/4" 11-3/4" under sink.water Water line 7-1/2 Garbage disposer, lines 34-1/4 MIN. I.R. MAX. Plumbing through area “A.” HOT cutoff valve are installed in 12" ± 1/4 Garbage disposer, 34-1/4Dishwasher MAX.11-3/4" opening for garbage disposerwa m Plumbing C valve are install ± 1/4SIDE VIEW view, areacutoff “C” (7-1/2"). This wil Dishwasher opening for garbage plumbing in cabinet “C” when ud Front of cabinet areaMAX. “C” (7-1/2" SIDE VIEW Toe more thanview, 20-1/2" specifD Flange cabinet “C kick Front of cabinet cabinet isplumbing less thaninthe 24" MIN (Pub. 1Toe more than 20-1/2" MA area 4" MAX.FlangeB tub front flange and the front of kick cabinet is less than th B area 4" MAX. front flange and th Dishwashers tub Installation Floor Dishwashers Installation 24" Floor (Pub. 1-G003 pg. 131B) May 12, 1993 GE/Hotpoint/RCA min. cabinet (Pub. 1-G003 pg. 131B) May 12, 1993 Floor 12" 24" Floor MIN. min. cabinet
Countertop 1-1/2" MIN. thick 10-1/4" MAX.
A 10-1/4" MAX.
A C
FRONT VIEW
FRONT VIEW 6" MAX. B
HOT WATER line to dishwasher is installed in area “B.” Garbage disposer, water lines to faucet, trap, waste air gap and water cutoff valve are installed in 12" wide cabinet shown in area “C.” Sink opening for garbage disposer must be dimensioned as shown in front view, area “C” (7-1/2"). This will provide clearance for the disposer and plumbing in cabinet “C” when using double bowl sink.
3/4" MIN.
6" MAX. B 24 24
12" MIN.
20-1/2" MAX. Wall Sink bowl 1" MAX. to 20-1/2" MAX. 11" MIN sink flange Sink bowl Drain CL 1" MAX.
3/4" MIN.
11" MIN
6" MAX. Drain CL
Wood Insert Cut-Out Dime
Wood Wood Insert Insert Cut-Out Cut-Out Dimensions Dimensions (in (in inches) inches)
Cabinet Cut-Out for Sink Dimensions (in inches)
GE/Hotpoint/RCA GE/Hotpoint/RCA
Undersink Dishwasher Wood Insert Dimensions (in inches) Door insert
Sink installation cutout
Panel Thic
A
3/
8" x 20" Adjacent cabinet rear cutout
5
Cabinet side adjacent to D/W FRONT VIEW
Door Door insert insert 18-7/8 Door insert
5
3-1/4 11-3/4
12-1/2
Access Access insert insert 3-11/16 Access insert 23-9/16
12
Cabinet cutouts for offset single and double bowl sinks. Dishwasher not provided with complete enclosure. Enclosures for sides, top, bottom and back must be provided by installer at time of installation.
A A
C C
B B
Inserts must not exceed When 1/4" thickness using GPF325 When GPF325 within 5/16" of using dishwasher 1/4" custom 1/4" custom dishwasher edge around full door door and and access access panel panel kit. kit. circumference. When using GPF375 When using GPF375 3/4" 3/4" custom custom dishwasher dishwasher door door and and access access panel panel kit. kit.
Front of Panel
Panel Panel Thickness Thickness 3/4
3/4 insert Access Front Front of of B Panel Panel
C
1-1/2
1-1/2 1-1/2 1/2 1/2
When using GPF325 1/4 dishwasher 1/4" custom 1/4 door and access panel kit. When using GPF375 3/4" custom dishwasher door and access panel kit.
Specification Created 10/07
Listed by Underwriters Laboratories
350512
1/2
GSM2260N GE Spacemaker® Under-the-Sink Dishwasher Features and Benefits • Stainless Steel Door - Brings a polished look to any kitchen • Spacemaker® Upper Rack - Makes the most of any space, providing a roomy area for glassware and dishes • 4-level PowerScrub™ Wash System - Four wash levels quietly and efficiently scrub dishes clean • Deluxe Silverware Basket - Provides convenient space and capacity to clean silverware efficiently and effectively • QuietPower™ Motor - Runs quietly and efficiently to keep the kitchen peaceful and quiet • HotStart™ Option - Preheats water before the main wash cycle for dependable performance every time • Model GSM2260NSS - Stainless steel
GSM2260NSS
Specification Created 10/07
350512
