Transcript
1
Firmware Check List C39 Firmware Setting Customer Name Default Value (Highlighted in Blue)
Module Name Filled By Customer (Highlighted in Red)
Copyright © 2011 GlobalTop Technology INC. All Rights Reserved. GT1-S2-00X-0X-X
Rev.110905
2
Firmware Check List C39
1. Baud Rate (bps) : □ Default: 9600 bps □ 4800 □ 14400 □ 19200 □ 38400 □ 57600 □ 115200 2. Update Rate (1~10Hz) : □ Default: 1Hz Others: □ 2 Hz □ 3 Hz □ 4 Hz □ 5 Hz □ 6 Hz □ 7 Hz □ 8 Hz □ 9 Hz □ 10 Hz 3. Datum: □ Default: WGS84 □ Tokyo-M □ Tokyo-A □ Other: 4. Data Decimal: ※ Sets the number of decimal places for longitude & latitude data in NMEA □ Default: 4 decimal places □ 6 decimal places 5. DGPS mode: ※ RTCM and SBAS cannot be enabled at the same time. ※ RTCM supported products: Gmm-u2p/SL3C ※ SBAS can only be enabled when update rate is less than or equal to 5Hz. □ Default: SBAS □ RTCM: Baud rate (bps): □ Default 9600 □ 4800 □ 14400 □ 19200 □ 38400 □ 57600 □ 115200 □ Disable 6. NMEA Sentence & Interval Period: ‘0’ = No output. Ex. GSV(5) -> Output 1 GSV sentence every 5-times interval. □ Default: GGA(1), GSA(1), GSV(5), RMC(1), VTG(1), GLL(0), ZDA(0) □ Custom: GGA(
), GSA(
), GSV(
), RMC(
), VTG(
), GLL(
), ZDA(
)
7. 3D Fix Output: ※ Supported products: Gmm-u2p / SL3C / PA6C Period range: 0.5sec~16sec ; Duty cycle options: OFF(Low), 50ms, 100ms, 200ms, 1/8, 1/2, 7/8, ON(High)
□ Default setting No Fix: Period: 2 sec; Duty cycle: 1/2 Fixed: Period: 0.5 sec; Duty cycle: OFF □ Custom No Fix: Period: Fixed: Period:
sec; Duty cycle: □OFF □50ms □100ms □200ms □1/8 □1/2 □7/8 □ON sec; Duty cycle: □OFF □50ms □100ms □200ms □1/8 □1/2 □7/8 □ON
□ Not Supported
8. 1PPS Output Duration: (Duty cycle range: 1~999ms) ※ Supported products: Gmm-u2p / SL3C/PA6C Copyright © 2011 GlobalTop Technology INC. All Rights Reserved. GT1-S2-00X-0X-X
Rev.110905
3
Firmware Check List C39 □Default: 100 ms
□Custom: Duty cycle:
ms
□Not Supported
9. Timing Mode: 1PPS pulse output mode selection ※ Supported products: Gmm-u2p /PA6C/ SL3C □Default: Output 1 PPS after obtaining 3D-Fix □Output 1PPS after TTFF □Output 1PPS after obtaining 2D-Fix □Always Output 1PPS □Not Supported 10. AIC: Active Interference Cancellation, refer to note 10 □Default: Enabled □Disabled 11. EASY: Embedded Assist System, refer to note 11 □Default: Enabled □Disabled 12. LOCUS: Internal logger function, refer to note 12 Logging Type: □Default: Full&Stop □ Overlap Logging Content: □Default: Basic □ Racing □ Search □ Saving □ All Logging Mode: □Default: Interval 15 sec, Fix Only □ AL □ Fix Only □ Normal □ Interval □ Speed
sec □ Distance
meters
m/s
13. 1-Sentence Output: (It can be outputted as ASCII or Binary format) ※ Note: For 1-Sentence output, Gtop will supply custom spec document based on customer requests, please contact support personnel to confirm the items/methods you desire. □Default: Disabled □Custom Input command: ASCII ONLY Output message: □ASCII □Binary □Both (Switchable by command) 14. Last Position Retention: (Continue to output last known position coordinate when GPS fix is lost) □Default: Disabled
□Enable
15. Magnetic variation: Outputs degree of magnetic variation & measured magnetic heading □Default: Disabled Copyright © 2011 GlobalTop Technology INC. All Rights Reserved. GT1-S2-00X-0X-X
Rev.110905
4
Firmware Check List C39 □Enable (If enable ,the data logger function cannot be enabled because of memory shortage) 16. Geofencing: Allows the user to set radius size around a target position. The GPS receiver will notify the user (in PGTOP serial format) if the current position is inside or outside this predefined boundary. ※ Supported products: Gmm-u2p/PA6C/SL3C □Default: Disabled □Enable 17. Distance Calculation: Outputs distance between two coordinates □Default: Disabled □Enable
Copyright © 2011 GlobalTop Technology INC. All Rights Reserved. GT1-S2-00X-0X-X
Rev.110905
5
Firmware Check List C39
Please make sure you read through the notes section carefully on page 4 and 5. If you have any questions, please feel free to contact our sales or support personnel.
Copyright © 2011 GlobalTop Technology INC. All Rights Reserved. GT1-S2-00X-0X-X
Rev.110905
6
Firmware Check List C39 Confirmed by C
stome Confirmed by Sales (Gl r:
Name (PrintbalTop)
d)
Name (Printed)
Signature
Signature
Date
Date
Note:
Filled by R&D (GlobalTop) Signature Date File Name Version Internal Code
Copyright © 2011 GlobalTop Technology INC. All Rights Reserved. GT1-S2-00X-0X-X
Rev.110905
7
Firmware Check List C39 Notes:
1. Baud Rate: High baud-rate is required for high update rate, as well as for additional NMEA output sentences. Please see “2. Update Rate” and “6. NMEA Sentence & Interval Period” for more details. Formula for calculating required baud rate, assuming each NMEA sentence takes a set amount of #: GLL=6, RMC=8, VTG=4, GSA=7, GSV=26, GGA=8, ZDA=5 If all NMEA sentences are turned on, The selected baud rate must be greater than > (6+8+4+7+26+8+5) x update rate x 100 So if the update rate is at 1 Hz with all NMEA sentences turned on, the formula will be equal to 6400, thus the selected baud rate must be 9600bps or greater! Caution: This formula is not applicable when setting baud rate / update rate / NMEA sentence using Mini GPS Tool or PMTK Command!
2. Update Rate: High baud-rate is required for high update rate. 3. Datum: Please ask our support personnel for a complete list of datums. 4. Data Decimal: Set the number of decimal places for longitude & latitude data reported in NMEA. 5. SBAS and RTCM cannot be enabled at the same time. 6. NMEA Sentence & Interval Period: This option sets the output interval period for each of the NMEA sentences. Please keep in mind that the rate of the NMEA sentences output is directly affected by the update rate. For example, if the default setting is chosen: “GGA( 1 ), GSA( 1 ), GSV( 5 ), RMC( 1 ), VTG( 1 )”, then GGA, GSA, RMC and VTG sentences will output once per second, while GSV will output once every 5 seconds if the update rate is at 1Hz. If the update rate is set to 10Hz, then using the above setting, GGA, GSA, RMC and VTG will now output 10 times per second, while GSV outputs 2 times per second.
7. 3D Fix Output: “Period” specifies the entire cycle time (high + low level signal), while "Duty cycle" specifies the period of time when the signal level is high. For example, if period is set to 2 sec and Duty cycle is set to 100ms, the entire cycle time will be 2sec, where the signal will be high for 100ms and low for 1.9sec. If period is set to 2 sec and duty cycle is set to 1/2, the signal will remain high for 500ms (1/2 of period), and low for 500ms. If duty cycle is OFF or ON, then the period time will be of no use, since it will remain low or high.
8. 1PPS: Sets the length (duration) of the pulse for 1PPS.
Copyright © 2011 GlobalTop Technology INC. All Rights Reserved. GT1-S2-00X-0X-X
Rev.110905
8
Firmware Check List C39
9. Timing Mode: Timing mode functions listed below can also be changed temporarily using MTK packet command 285. Please be aware this is only supported in firmware kernel version AXN1.5
1PPS Output Duration
1PPS pulse output mode selection
10. Active Interference Cancellation (AIC): Provides effective narrow-band interference and jamming elimination. The GPS signal could be recovered from the jammed signal, and let user get better navigation quality.
11. Embedded Assist System (EASY): is the abbreviation of Embedded Assist System. The benefits are including:
EASY to TTFF EASY works as an embedded software which can accelerate TTFF by predicting satellite navigation messages from received ephemeris.
EASY to calculate No additional computing interval for EASY task. EASY was efficiently scheduled and computed in the free time of every second after GPS navigation solution.
EASY to design-in World leading technology with no additional design-in efforts.
12. LOCUS (Data Logger solution): 12.1 Auto logging data to MTK chip internal flash, no need to wakeup HOST side. 12.2 Smart overlapping mechanism to keep latest logger data (4KB base). 12.3 Flexible configuration to support most logging type, mode and contents. 12.4 Logger capability in MTK chip internal flash: (1) With 1 sector flash (64KB), user can log >16 hours 12.5 Details for logging content: Table
Naming
Size
UTC
Fix Type
Lat
Lon
(bytes)
(4)
(1)
(4)
(4)
Height Speed Heading HDOP SatNo Checksum (2)
A
Basic
16
o
o
o
o
o
B
Racing
20
o
o
o
o
o
C
Search
18
o
o
o
o
o
D
Saving
13
o
o
O
E
All
23
o
o
o
o
(2)
(2)
(2)
(1)
(1) O
o
O
O O
O O
o
Copyright © 2011 GlobalTop Technology INC. All Rights Reserved. GT1-S2-00X-0X-X
o
o
o
o
O
Rev.110905
9
Firmware Check List C39 12.6 LOCUS operation during Normal and Power saving mode Positioning
Normal mode
Power saving mode (Periodic / AlwaysLocate running)
LOCUS config
AL mode
No logging
Logging once before go to sleep
Normal mode
Logging per fix
Logging per fix
Interval mode
Logging when over the interval
Logging when over the interval
Distance
Logging when over the distance
Logging when over the distance
Speed
Logging when over the speed
Logging when over the speed
AL mode+Normal mode Logging per fix
Logging once before go to sleep
AL mode+Interval mode Logging when over the interval
Logging once before go to sleep
13. 1-Sentence: Customize and compact the output NMEA sentence to decrease MCU loading. See One Sentence Output page for more details. If you wish to use binary mode, one sentence output must be enabled, please specify the desired NMEA items. Optional functions are supported, but customer will need to supply detail algorithm or methods.
14. Last Position Retention: convenient yet elegant solution that allows the GPS module to continue output its last known position in the event of losing GPS satellite fix. Please refer to our website.
15. Magnetic variation: Magnetic Variation data output allows electronic compass based device to adjust for declination when using bearing to determine directions (Ex. Ships) Please refer to website
16. Geofencing: Set a radius around a target position, and informs the user if the receiver position is inside or outside this predefined boundary, like school attendance zone or neighborhood boundary. Please refer to website
17. Distance calculation: GlobalTop GPS module is able to specify the exact line-of-sight distances between current location and other points of interests. This calculation is done internally within the GPS module and can help decrease the calculation loading on the main processor. Please refer to website
Copyright © 2011 GlobalTop Technology INC. All Rights Reserved. GT1-S2-00X-0X-X
Rev.110905
10
Firmware Check List C39
Other Notes:
1. AGPS function is supported in firmware version Mcore2.02 & AXN0.3 or later revisions. 2. “Navigation Speed Threshold” function can be enabled in all GPS modules to help reduce stationary drifting problem of GPS through a special drifting elimination algorithm. If you wish to enable or change the threshold value (1.0 m/s), please contact us. In addition, the setting can also be changed temporarily using MTK packet command 397.
3. Items 1, 2, 3 (mini GPS Tool only), 5, 6, can be changed through PMTK command or Mini GPS Tool, but will return to chosen setting when re-booted without supplying backup power. Please contact us for the complete PMTK command document or download Mini GPS Tool from www.gtop-tech.com.
4. “Application notes” document for our module is available. It contains design tips, layouts, and cautions you should watch out for when designing around GlobalTop GPS modules. Please contact us if you have not received your application notes document.
Copyright © 2011 GlobalTop Technology INC. All Rights Reserved. GT1-S2-00X-0X-X
Rev.110905
