Transcript
Grass Valley Model 4000 Digital Production Switching Systems
Ordering Guide December 1997 Revision 1
Model 4000
Ordering Guide
Contents PRODUCT OVERVIEW 4000-2 Standard Options Package 4000-3 Standard Option Package 4000-3 Control Panels Control Cable
STANDARD FEATURES INCLUDED IN 4000-2PKG OR 4000-3PKG Power Cables Effects Send Framestore Look-Ahead Preview Tally Input Modules Output Module Borderline Key Edge Generator
1 4 5 5 5
6 6 6 7 7 7 7 7 8
ORDERABLE OPTIONS 9 Control Panel Options Input Options Output Options 4000-2
9 9 10
Output Options 4000-3 Remote Aux Panels Maskstore Secondary Wipe Generator Borderline Key Edge Generator Chroma Keyer Tally Expansion K-Scope Interface Control Panel Redundant Power Supply Electronics Frame Redundant Power Supply Manuals
TECHNICAL SPECIFICATIONS
17
MODEL 4000 VIDEO SPECIFICATIONS
18
TEKCARE SERVICE PRODUCTS
22
WARRANTY
23
© Tektronix, Inc. All rights reserved. Printed in USA. Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supersedes that in all previously published material. Specifications and price change privileges reserved. TEKTRONIX, TEK, Grass Valley Group, Borderline, E-MEM, TEN-X, Wavelink, and ìGVGî are registered trademarks, and Air Link, Auto Match, Doubletake, E-Disk, Eagle V, Emphasys, EZ-Link, 409, Grass Valley, Horizon, Jogger, Kadenza, Kaleidoscope, K-Mask, Key-Layer, KeyLink, Krystal, MASTER System, Master 21, MAX, Omni-Key, Performer, Programmed Motion, Silhouette, Softset, Streamline, Super Edit, TEN-20, 20-TEN, Trace, TrailBlazer, VideoDesktop, Flex-Time, and XEDL are trademarks of Tektronix, Inc., P. O. Box 1000, Wilsonville, OR 97070-1000 U.S.A. The information in this manual is furnished for informational use only, is subject to change without notice, and should not be construed as a commitment by Tektronix, Inc. Tektronix assumes no responsibility or liability for any errors or inaccuracies that may appear in this publication. Tektronix, Inc., Video and Networking Division, P. O. Box 1114, Grass Valley, California 95945 U.S.A.
ii
11 12 13 13 14 14 15 15 16 16 16
Model 4000
Ordering Guide
PRODUCT OVERVIEW The Model 4000 Digital Production Switching System utilizes component digital signal processing for superior image quality and fidelity.
The 4000 series of production switchers consists of two models— the Model 4000-2PKG and the Model 4000-3PKG. The Model 4000-2PKG includes a full-function control panel with a two Mix/Effects (M/E) system, a full length Program/Preset Mixer with mix and wipes and Dual Downstream Keyers (DSK). Up to 24 video inputs can be controlled directly from the Model 4000-2 control panel, plus another 24 shifted inputs. The system architecture provides unlimited effects re-entry. The full list of included options is provided under the package description later in this guide. The Model 4000-3PKG includes a three Mix/Effects (M/E) system and a full-length Program/Preset Mixer with Dual Downstream Keyers (DSK). Two Control Panels are available. The standard 3 M/E Panel is designed for the demanding requirements of the "live" broadcast environment with separate key rows per M/E, and individual E-MEM® control of each M/E. Up to 24 video inputs can be controlled directly from the Model 4000-3 control panel, plus another 24 shifted inputs. The system architecture provides unlimited effects re-entry.
The standard panel consists of a main “tub” and a separate accessory panel. The modular “truck” panel includes a modular 3 Mix/Effects main panel and modules specifically designed to meet the needs of mobile production applications.
The Model 4000 Series Production Switching System can include up to 64 inputs for video and key sources. Every video input can have an associated key input provided that the total number of video and key inputs does not exceed 64. The internal format of the Model 4000 is CCIR 601 component digital. Input and output formats have 10 bit resolution. The input formats are user selectable and may be a mix of component analog and component serial digital. Each serial input module supports 8 inputs. Each input is defined through personality programming to be a video or external key source. Automatic input timing is provided for each serial input. Program outputs from the switcher are provided in serial digital and analog component formats. Each M/E system includes two modes of operation. The traditional mode allows two foreground keys, with exchangeable priority, to be composited over the backgrounds. The Lamina™ Image Layering mode provides keying on the two background buses. Lamina mode provides 4 layer compositing
within a single M/E. The composited image and composited key from an M/E in the layering mode is available as a source on another M/E or the DSK for further compositing. The background keyers provide luminance or linear keys with external key sources or self keys. Preset wipes are also provided on the background keyers. Unrestricted break-away keying is provided on all keyers. Any input to the switcher can be used as a key source.
Each M/E has two full-function foreground keyers. The foreground keyers can be enhanced with Chroma Key and Borderline® key edge generator accessories. Each of the two full-function keyers in an M/E are capable of linear, luminance, and chroma keys (with dual chroma key option). The M/E keyers can use any of the switcher inputs for a video fill or an external key source. Each fill video can have an external key source associated with it or act as a self key. Each foreground keyer has several masking sources available. These include a dedicated shutter mask for each keyer, a mask video input, the M/E's wipe patterns, or optional mask framestore. NonAdditive Mix is available between the two foreground keyers.
1
Model 4000
Six matte generators are included in each M/E. These provide independent color matte fill for the foreground keyers, Borderline® key edge generator, and preset wipe borders. Each of the six matte generators has color wash facilities. Two color background sources, a color black source, and a test signal can be assigned to any video input. Each color background source has the unique Background Wash mode.
Each M/E and the Program/Preset Mixer incorporate Preset Black. Auto Transition and Cut are standard in the M/Es and DSK. Mask dim and show key are available on the preview output. Show Key is a feature that routes the current key signal out to the preview monitor to assist in setting up keyers. Mask dim allows positioning of the masked area by dimming that area on the preview monitor.
Each M/E includes a Full-Additive Mix (FAM) mode. FAM allows all four layers to be additively mixed together. The output of the FAM is clipped to proper levels. Signal processing facilities are also included in the M/E. Each input bus has adjustments for video gain, chroma gain, coring, key timing and opacity.
The Model 4000 wipe systems include an extensive set of patterns. These patterns can be modified with rotation, pattern split, border width, border symmetry, border
2
Ordering Guide
opacity, edge softness, aspect, vertical and horizontal multipliers, modulation and a rate controlled pattern positioner. The vertical and horizontal multipliers repeat patterns up to 8 times. A Texture pattern allows the creation of randomized noise for the creation of unique textures. An optional Secondary Wipe Generator provides additional wipe pattern flexibility within the M/E. The secondary wipe generator can be used for mask generation, a different preset pattern, or matte generator modulation. It also provides patterns which can be mixed with the patterns of the primary generator for the creation of limitless new pattern.s The pattern mix function also includes pattern NAM.
Standard E-MEM® Effects Memory System provides storage for 100 complete switcher setups. Learns and recalls of switcher effect setups can be initiated on a combination of levels. (M/E 1, M/E 2, PGM/PST, DSK, BKGD, ETC.). The useful and versatile Effects Dissolve and Sequencer facilities are included in the E-MEM system. The basic EMEM system's operation has been greatly enhanced with the addition of keyframe based effects. This allows the smooth motion of wipe patterns around the screen. Keyframe-based effects in the Model 4000 E-MEM system simplify the creation of consolidated switcher and digital effects. A 3.5 inch floppy disk drive is included for storage of EMEM Effects set ups.
An integral sync pulse generator is included and allows the system to be timed to an analog reference signal. The field rate is user selectable and can be set at 525/60 or 625/50. The system is also user selectable for aspect ratios of 4x3 or 16x9 at 13.5 MHz.
The Model 4000 includes a dedicated editor interface port, diagnostic/maintenance port, status terminal port and GPIs and additional serial communication ports. Frame and control panel are each powered separately. The frame power supplies mount directly below the main electronic chassis. The panel power supplies, standard as well as redundant, are mounted inside of the control panel. One set of manuals, module extenders, and lens designations are supplied with each system.
The control panel is connected to the electronics frame using a single serial cable. A 50-meter control panel cable is included with each control panel. The control cable can be a maximum of 300 meters in length. Specification are available for the building of cables longer than 50 meters.
Model 4000
The Model 4000 Digital Production Switcher includes many exciting and useful standard features. A summary of the key standard features follows. • • • • • • • • • • • • • • •
• •
• • • • •
Adherence to CCIR 601 Unlimited Mix/Effects ReEntry 2 Full-function Keyers in Each M/E Dual Downstream Keyers Up to 64 Inputs for Video and Key Sources Analog and Serial Digital Input Formats Auto-Timed Serial Component Digital Inputs Shaped or Unshaped Video Inputs PGM and Switched PVW Analog Outputs Full 10 Bit Digital Input and Outputs Lamina™ Image Layering on each Mix/Effects Companion Key Channel Throughout the Switcher Extensive Key Masking in each Keyer Six Dual Matte Generators in Each M/E Two Dual Background Generators with Independent Wash Two Dual Matte Generators for each Downstream Keyer Every Matte Generator includes Color Wash Capability Color Black Generator Full Complement of Wipe Patterns Wipe Pattern Mix and NonAdditive Mix (NAM) Key Priority Transition Mode CHROMATTE™ Advanced Chroma Keyer for M/E 1
Ordering Guide
•
• • •
•
• • • •
• •
• •
• • • • • • • • •
Borderline® Key Edge Generator for each M/E Foreground Keyer and DSK Look Ahead Preview & Clean Feed Output for Mix/Effects Frame Store Four Effects Send/Auxiliary Switching Buses with Video and Key Outputs for feeding Digital Effects Systems E-MEM Effects Memory System with Effects Dissolve and Sequencer 100 E-MEM Registers Keyframe Based Effects within each E-MEM Register 3.5" Micro-Floppy Disk for EMEM Data Storage Personality Programming for Video and Key Input Assignment M/E Swap, M/E Copy, and Color Matte Copy Adjustable Luminance and Chroma Gain on each Video Input Bus Adjustable Black Coring on each Video Input Bus Adjustable Key Timing in Keyer 1 and Keyer 2 on each M/E Non-Additive Mix (NAM) in each Mix/Effects Full Additive Mix (FAM) in each Mix/Effects Maintenance/Status Port at Signal Processor Chassis Eight Programmable GPI Inputs and Eight GPI Outputs Editor Serial Interface Port Safe Title and Action Generator Fault Tolerance (to the M/E bank level) Built In Hardware and Software Diagnostics Status Port at Control Panel
• • •
Comprehensive Technical and Operational Documentation Module Extenders Operation and Installation Video Tapes
The Model 4000 Digital Production Switcher also includes many extraordinary optional features. A summary of these follows. •
•
•
• •
•
• • • • • • •
A Second Wipe Pattern Generator for each Mix/Effects and the PGM/PST Mixer (4000-2 only) Fixed-Timed Analog Component Primary Input Modules. (Each provides 2 video and 2 key terminating inputs. Format can be RGB, YUV, Beta® or MII) Fixed-Timed Analog Component Chroma Key Input Modules. (Each provides 2 full bandwidth, terminating inputs. Format can be RGB, YUV, Beta or MII) Serial Input Modules (Each provides eight serial inputs) CHROMATTE™ Advanced Chroma Keyer for M/E 2 and M/E 3 (4000-3) Borderline® Key Edge Generator for each M/E Foreground Keyer and DSK Clean Feed Output for Program/Preset Mixer Mask framestore and “garbage” mask Ten Utility Auxiliary Switching Buses Redundant Power Supplies Tally Relay Output On-Site Operational Training Factory Operations and Technical Training
3
Model 4000
Ordering Guide
4000-2 Standard Options Package Additional input and output modules can be added to this package. See Input and Output Options sections for details. A Model 4000 Component Digital Production Switcher can include up to 8 serial input modules for a total of 64 inputs, which can be a mix of video and key. A maximum of 8 analog input options providing 16 CAV and 16 key inputs and 4 serial input options providing 32 video or key inputs may be included.
MODEL #
Model 4000-2 Digital Production Switching System Package This basic system configuration includes the following components: • • • • •
• • • • • • • • • • •
4
2 Mix/Effects Systems and Program/Preset Mixer with mix/ wipes and Dual DSK Full-function Control Panel with access to 48 video sources One analog output module for DSK program video and switched preview video Two serial digital input modules for 16 inputs One serial digital output module for program video and key, for M/E1, M/E2, and DSK, plus Mask and switched video outputs Safe Title and Action Generator Effects Send matrix and serial digital outputs for Aux 1A/B through 4A/B Video/Key framestore Borderline Key Edge generator for M/E1 Keyer1, M/E2 Keyer1, and DSK1 Dual component chromakeyer for M/E1 Look-ahead preview for M/E1, M/E2, PGM/PST, DSK1 and DSK2 Operation in either 525/60 or 625/50, 4:3 or 16:9 standards. Power supplies Module extenders Instruction manuals One 50-meter control cable
4000-2PKG
Model 4000
Ordering Guide
4000-3 Standard Option Package
Model 4000-3 Digital Production Switching System Package
Additional input and output modules can be added to this package. See Input and Output Options sections for details. A Model 4000 Component Digital Production Switcher can include up to 8 serial input modules for a total of 64 inputs, which can be a mix of video and key. A maximum of 8 analog input options providing 16 CAV and 16 key inputs and 4 serial input options providing 32 video or key inputs may be included.
This basic system configuration includes the following components. Please note that this configuration does not include any control panels. These must be ordered separately. • • • •
• • • • • • • • • • •
4000-3PKG
3 Mix/Effects Systems and Program/Preset Mixer with Dual DSK One analog output module for program video, program key, mask bus video, and switched preview video Two serial digital input modules for 16 inputs One serial digital output module for program video and key, for M/E1, M/E2, and DSK, plus Mask and switched video outputs Safe Title and Action Generator Effects Send matrix and serial digital outputs for Aux 1A/B through 4A/B Video/Key framestore Borderline Key Edge generator for M/E1 Keyer1, M/E2 Keyer1, M/E3 Keyer1, and DSK1 Dual component chromakeyer for M/E1 Look Ahead Preview for M/E1, M/E2, M/E3, PGM/PST, DSK1 and DSK2 Tally Output main frame Operation in either 525/60 or 625/50, 4:3 or 16:9 standards. Power supplies Module extenders Instruction manuals.
4000-3 Control Panels Specify 4000-3-PNLS or PSWL-3T-40 when ordering. Standard 3 M/E Control Panel with Access to 48 Video Sources
4000-3-PNLS
Modular 3 M/E Control Panel Designed Specifically for Mobile Production Applications
PSWL-3T-40
•
Control Cable
4000-3T Control Panel includes 24 display input readout panels
50-Meter Control Cable One 50-meter control cable is included with the system. Maximum cable distance between control panel and electronics frame is 300 meters. Specifications are available for building cables longer than 50 meters.
5
Model 4000
Ordering Guide
STANDARD FEATURES INCLUDED IN 4000-2PKG OR 4000-3PKG Power Cables (For both 4000-2 and 4000-3) In order to meet UL and TUV safety requirements, the appropriate power cables must be used with the system.
Both the TUV and the UL approved cables are provided with each unit.
TUV Approved Power Cables These cables must be used on all units installed in Europe. The control panel power will be supplied with a molded grounding connector (IEC 320-C13) on one end with pigtails on the other. The main electronics frame will have the power cable attached with pigtails on the free end. Appropriate connectors to be supplied by customer per local requirements. Areas outside of Europe may or may not require a TUV approved cable, please check local requirements and order accordingly.
UL Approved Power Cables These cables must be used on all units installed in the United States, Canada, South America and South East Asia. A Standard 110VAC power cable is supplied with the Control Panel. It has a molded grounding plug (NEMA 5-15P) at one end and a molded grounding connector (IEC 320-C13) at the other end. The main electronics frame is supplied with a power cable with a 20 Amp Twist-Lock 240 VAC NEMA Type L6-20P Plug attached.
Effects Send
Effects Send System Effects Send System provides a system of crosspoints and I/O buses that allow the integration of external effects devices within an M/E bank. Using this system, it is possible to "fly" keys or any layer within an M/E bank (e.g., the effects device is "spliced" into the M/E between the keyer and the compositing circuits.) The Effects Send System includes a switching matrix and serial digital outputs for AUX/Effects Send Busses 1-4 Video and Key.
6
Model 4000
Framestore
Ordering Guide
Video and Key Framestore Provides 4 frames of storage for video, and 4 frames for key. Video and/or key may be repositioned over full raster. Video and/or key may be blurred, H and V separately, and Y and C separately. Video may have hue rotated 0-360 degrees (blur, hue rotate, and subpixel repositioning are mutually exclusive). The framestore supports the following bit map effects: Posterize, Solarize, Color Modulate, Contrast stretching or Hue Modulate, and Mosaics. Drop shadow is repositionable over full raster with opacity and blur control. There is also rectangular crop on video and/or key.
Look-Ahead Preview
Look-Ahead Preview Provides look-ahead preview processing for all M/E systems, Program/Preset and DSK in the Model 4000. This option also provides a clean feed output from the Mix/Effects in place of the M/E Key Output. The Mix/Effects Look-Ahead Preview option allows you to preview the next event on the preview bus output.
Tally (Included for 4000-3 only)
Input Modules
Tally Output (Mainframe) Provides relay closures for the on-air sources in the Model 40003. These contact closures may be used for camera, monitor, or machine tally indicators. This module mounts in the main electronics frame. This option is not included in the 4000-2PKG, but is an orderable option.
Two Serial Digital Input Modules Provide 16 inputs for video or key signals
Output Module
Serial Digital Output Module providing the following signals: • Mask
• Switched Preview
• DSK Program Video
• DSK Program Key
• M/E 1 Program Video
• M/E 1 Program Key/Clean Feed Video (switchable)
• M/E 2 Program Video
• M/E 2 Program Key/Clean Feed Video (switchable)
7
Model 4000
Borderline Key Edge Generator
Ordering Guide
BORDERLINE Key Edge Generator Included in the 4000-2PKG and 4000-3PKG Standard Packages: • •
for M/E1 Keyer 1, M/E2 Keyer 1, and DSK1 in the 4000-2 for M/E1 Keyer 1, M/E2 Keyer 1, M/E3 Keyer 1 and DSK1 in the 4000-3
Allows the foreground keyer to be enhanced with edging effects. Modes include a 1 to 3 line border, shadow with 1 to 6 line offset, a 1 to 6 line extrude, or a 1 to 3 line outline. Edges can be any luminance level or colorized with a flat or color wash. Shadow and extrude may be positioned down left or down right.
Chroma Keyer
Chromatteª Advanced Chroma Keyer Included for M/E1 in the 4000-2PKG and 4000-3PKG Standard Packages. Provides component chroma keying on both foreground keyers in the Mix/Effects in which it is installed. Color background suppression, foreground suppression and shadow processing are included. These options require a minimum of one option PSWL530-2 or 4000-530-3 as a prerequisite if external CAV video inputs are to be used. Any internal 4:2:2 chroma key can be done without a PSWL-530-2.
8
Model 4000
Ordering Guide
ORDERABLE OPTIONS Control Panel Options
Input Readout Display Panels, 24 displays for 3 M/E Studio Panel Only
PSWL-40-3
The Readout Display Option provides 24, 4-character readouts for mounting in the Accessory Panel of the 4000-3 only.
Input Options
Digital Inputs
The following input modules may be added to a standard package. A Model 4000 Digital Production Switcher can include up to 8 serial input options for a total of 64 inputs. These may be video and key. They may be a combination of Serial Digital formats in groups of eight, and analog in groups of 4.
By purchasing optional input modules, the Model 4000 can have up to 64 inputs. A maximum of 32 of these can be analog (16 CAV and 16 analog keys). The system can accept up to 8 Serial Input modules. Each Serial Input module provides 8 active loop-thru inputs which can be either video or key.
Please note that only serial digital input signals are autotimed. All CAV and analog key inputs including CAV chroma key inputs are not auto timed.
8 Looping Serial Digital Input Module
PSWL-201-2
With Auto Timing for Model 4000 2 Systems.
8 Looping Serial Digital Input Module
4000-201-3
With Auto Timing for Model 4000-3 Systems.
Analog Inputs The system can accept up to 8 analog modules. Each 4000-202-2, 4000-202-3 Analog Input Module Set provides 2 CAV inputs and 2 analog Key inputs and replaces a serial input module. Each of the Analog Input Module Sets can be expanded to 4 CAV inputs and 4 analog key inputs with the addition of one 4000-203 Analog Input Expansion Module Set.
These signals must be 4 Input CAV and Analog Key Input Module timed relative to reference Not autotimed. For 4000-2 System. to the switcher. Module Set Provides for 2 CAV and 2 analog key inputs only. Module set can be expanded to 8 inputs, 4 CAV and 4 analog key inputs with the addition of one option 4000-203. Analog inputs are not autotimed.
4 Input CAV and Analog Key Input Module
4000-202-2
4000-202-3
Not autotimed. For 4000-3 Systems.
4 Input CAV and Analog Key Input Expansion Module
4000-203
Not autotimed. For 4000-2 and 4000-3 Systems. Module Set Provides for 2 CAV and 2 analog key inputs only. Only one of these options can be added to each installed -4000202-2 or 4000-202-3 option. Analog inputs are not autotimed.
9
Model 4000
4000-2 Output Options The following output options may be added to the standard package. Each output option provides outputs for up to eight different switcher outputs.
Please note that all output signals are timed relative to each other with the exception of the utility aux busses 5 A/B through 9 A/ B. Aux busses 5 A/B through 8 A/B can be ordered either as a timed or untimed output module. Aux bus 9 A/B is always untimed.
Ordering Guide
Each Model 4000 output module provides outputs for groups of up to eight different output signals. All Model 4000 systems come standard with one analog output module and one serial digital output module. The analog output module provides outputs for the following: • •
DSK Program Video Switched Preview Video
Serial Digital Output Module A total of 2 optional Serial Digital Output Modules can be installed in the Model 4000-2 Switcher. Following are descriptions of the outputs supported by this module.
Serial Digital Output Module providing the following signals for the Model 4000-2: • M/E 1 Preview Video
• M/E 2 Preview Video
• DSK Preview Video
• PGM/PST Preview Video
order: PSWL-301 then specify: PSWL-SEROUT2
• Aux Bus 9A Video (untimed) • Aux Bus 9B Video (untimed) Clean Feed Video
Serial Digital Output Module providing the following Untimed signals for the Model 4000-2: • Aux Bus 5A Video
• Aux Bus 5B Video
• Aux Bus 6A Video
• Aux Bus 6B Video
• Aux Bus 7A Video
• Aux Bus 7B Video
• Aux Bus 8A Video
• Aux Bus 8B Video
order: PSWL-301 then specify: PSWL-SEROUT3
Aux busses 7A/7B, 8A/8B, Note: The timed and untimed Serial Digital Output Modules are mutually exclusive. and 9A/9B can only be accessed through an editor or via Remote Aux Bus Control Panels.
Serial Digital Output Module providing the following Timed signals: • Aux Bus 5A Video
• Aux Bus 5B Video
• Aux Bus 6A Video
• Aux Bus 6B Video
• Aux Bus 7A Video
• Aux Bus 7B Video
• Aux Bus 8A Video
• Aux Bus 8B Video
Note: The timed and untimed Serial Digital Output Modules are mutually exclusive.
10
PSWL-304-2
Model 4000
4000-3 Output Options
Ordering Guide
Serial Digital Output Module A total of 3 Serial Digital Output Modules can be installed in the Model 4000-3 Switcher. Following are descriptions of the optional outputs supported by this module.
Serial Digital Output Module providing the following signals for the Model 4000-3: • M/E 3 Program Video
• M/E 3 Program Key/Clean Feed Video (switchable)
• M/E 1 PVW/Look Ahead
• M/E 2 PVW/Look Ahead
• M/E 3 PVW/Look Ahead
• DSK PVW/Look Ahead
• Clean Feed Video
• DSK Preview Video
Serial Digital Output Module providing the following signals for the Model 4000-3: • Framestore Video
• Framestore Key
• Aux Bus 9A Video (untimed)
• Aux Bus 9B Video/Key (untimed)
order: PSWL-301 then specify: PSWL-SEROUT1
order: PSWL-301 then specify: PSWL-SEROUT4-3
Serial Digital Output Module providing the following Untimed signals for the Model 4000-3: • Aux Bus 5A Video
• Aux Bus 5B Video
• Aux Bus 6A Video
• Aux Bus 6B Video
• Aux Bus 7A Video
• Aux Bus 7B Video
• Aux Bus 8A Video
• Aux Bus 8B Video
order: PSWL-301 then specify: PSWL-SEROUT2
Note: The timed and untimed Serial Digital Output Modules are mutually exclusive.
Serial Digital Output Module providing the following Timed signals for the Model 4000-3: • Aux Bus 5A Video
• Aux Bus 5B Video
• Aux Bus 6A Video
• Aux Bus 6B Video
• Aux Bus 7A Video
• Aux Bus 7B Video
• Aux Bus 8A Video
• Aux Bus 8B Video
4000-304-3
Note: The timed and untimed Serial Digital Output Modules are mutually exclusive.
11
Model 4000
Ordering Guide
Remote Aux Panels
Single Bus Remote Aux Bus Control Panel
The Remote Aux Bus Control Panels provide remote access to all aux busses within the Model 4000. The Remote Aux Bus Control Panels are required when manual access to Aux busses 7A/7B, 8A/8B, and 9A/9B. Access to these are not supported on the Control Panel as separate aux control buttons, but are accessible form the menu.
Provides control for one Auxiliary Switching Bus, 1 R.U. This panel is similar to those used on Horizon control panels, a single row of buttons consisting of a dome switch with an integral LED.
Remote Aux Bus Control Cable
50-Meter Remote Aux Bus Cable (included with each Aux Bus control panel)
Single Bus Remote Aux Bus Control Panel
Multi Bus Remote Aux Bus Control Panel Provides control for all Auxiliary Switching Buses, 3 R.U's. This panel consists of three rows of Veetronix-type switches.
Remote Aux Bus Power Both the TUV and the UL power cables are provided with each Cables Remote Aux Bus Control Panel.
TUV Approved Power Cables This option must be used with all units installed in Europe. The control panel power will be supplied with a molded grounding connector (IEC 320-C13) on one end with pigtails on the other. Areas outside of Europe may or may not require a TUV approved cable, please check local requirements and order accordingly.
12
PSWL-425
Provides control for one Auxiliary Switching Bus, 2 R.U's. This panel consists of two rows of Veetronix-type switches with incandescent lamps and user changeable key cap legends.
This cable is terminated on one end with a 9-pin "D" connector for connection to the electronics frame, and unterminated on the other end for connection to the Aux Panels The maximum total length of cable interconnecting all aux panels is 300 m. Interconnection between aux panels can use these cables by removing the 9-pin "D" connector, or standard Belden 8451 cable can be used.
In order to meet UL and TUV safety requirements, the appropriate power cables must be used with each remote panel.
PSWL-420
UL Approved Power Cables This option must be used with all units installed in the United States, Canada, South America and South East Asia. A Standard 110VAC power cable is supplied with the Control Panel. It has a molded grounding plug (NEMA 5-15P) at one end and a molded grounding connector (IEC 320-C13) at the other end.
PSWL-430
Model 4000
Maskstore
Ordering Guide
Maskstore Maskstore provides the ability to create ÒgarbageÓ masks using a Wacom compatible graphics tablet, and to store the created mask.
4000-500
The following Wacom graphics tablet models are supported: (Tektronix does not supply the tablet) • • • •
Secondary Wipe Generator
KT-0405-R “ART PAD” (PC compatible version) UD—XXXX—R (Any PC-compatible UD-series tablet) UD-608-R “ART Z” (PC compatible version) SD series (these tablets are now obsolete; they may be used if a pressure sensitive pen is used with the tablet)
Secondary Wipe Pattern Generator (2 M/E)
PSWL-510-2
This option provides a second, wipe pattern for both M/E 1 and M/E 2 in the Model 4000-2. This option allows two independent wipe patterns within one M/E. The secondary wipe pattern can be mixed with the primary generator's pattern to create many other unique and exciting patterns. It can also be used as a mask source and a matte generator modulation source.
Secondary Wipe Pattern Generator for Program/Preset Mixer
4000-515
This option provides a second, wipe pattern for the Program/ Preset Mixer for the 4000-2 only. This option allows two independent wipe patterns The secondary wipe pattern can be mixed with the primary generator's pattern to create many other unique and exciting patterns. It can also be used as an additional mask source and a matte generator modulation within the Program/Preset Mixer.
Secondary Wipe Pattern Generator (3 M/E)
PSWL-510-3
This option provides a second, wipe pattern for M/E 1, M/E 2 and M/E 3 in the Model 4000-3. This option allows two independent wipe patterns within one M/E. The secondary wipe pattern can be mixed with the primary generator's pattern to create many other unique and exciting patterns. It can also be used as a mask source and a matte generator modulation source.
13
Model 4000
Borderline Key Edge Generator Can be ordered for M/E 1Keyer 2, M/E 2-Keyer 2, M/E3 Keyer 2 (4000-3) or DSK2. Max. 3 per 4000-2 switcher, and 4 per 4000-3 switcher.
Ordering Guide
BORDERLINE Key Edge Generator Included in the 4000-2PKG and 4000-3PKG Standard Option Packages: • •
for M/E1 Keyer 1, M/E2 Keyer 1, and DSK1 in the 4000-2 for M/E1 Keyer 1, M/E2 Keyer 1, M/E3 Keyer 1 and DSK1 in the 4000-3
Allows the foreground keyer to be enhanced with edging effects. Modes include a 1 to 3 line border, shadow with 1 to 6 line offset, a 1 to 6 line extrude, or a 1 to 3 line outline. Edges can be any luminance level or colorized with a flat or color wash. Shadow and extrude may be positioned down left or down right.
Borderline Key Edge Generator for M/E 1-Keyer 2
order: PSWL-521 then specify: ME1K2
Borderline Key Edge Generator for M/E 2-Keyer 2
order: PSWL-521 then specify: ME2K2
Borderline Key Edge Generator for M/E 3-Keyer 2
order: PSWL-521 then specify: ME3K2
(4000-3 Only)
Borderline Key Edge Generator for DSK2
Chroma Keyer
order: PSWL-521 then specify: DSK2
Dual Analog Component Chroma Keyer Input Provides two full-bandwidth manually timed analog component inputs for use by the Chromatte Advanced Chroma Keyer option. Up to three of these options, for a total of 6 analog component inputs, may be included in the system. A minimum of one option PSWL-531 is required.
14
Dual Analog Component Chroma Keyer Input for 4000-2 Systems
PSWL-530-2
Dual Analog Component Chroma Keyer Input for 4000-3 System
PSWL-530-3
Model 4000
Ordering Guide
Can be ordered for M/E 2 Chromatteª Advanced Chroma Keyer and for M/E 3 in 4000-3. Included for M/E1 in the 4000-2PKG and 4000-3PKG Standard Max.1 per 4000-2 and 2 per Option Packages. 4000-3. Provides component chroma keying on both foreground keyers in the Mix/Effects in which it is installed. Color background suppression, foreground suppression and shadow processing are included. These options require a minimum of one option PSWL530-2 or 4000-530-3 as a prerequisite if external CAV video inputs are to be used. Any internal 4:2:2 chroma key can be done without a PSWL-530-2.
Tally (4000-2 only)
Tally Expansion
Chromatteª Advanced Chroma Keyer for 4000-2 and 4000-3, M/E2
order: PSWL-531 then specify: ME2
Chromatteª Advanced Chroma Keyer for 4000-3, M/E3
order: PSWL-531 then specify: ME3
Tally Output (Mainframe)
4000-570-2
Provides relay closures for the on-air sources in the Model 40003. These contact closures may be used for camera, monitor, or machine tally indicators. This module mounts in the main electronics frame. This option is mutually exclusive with PSWL in slot D1.
External Tally Expansion Frame
PSWL-575
Provides an external 2 R.U. 19 inch frame with redundant internal power supplies, and will accept up to three tally expansion modules (PSWL-576). This option, with appropriate tally expansion modules, provides for M/E ISO and individual bus ISO tally. This expansion frame will not accept the internal tally output board mounted in the main electronics frame. Frame includes 16 meter cable for connection to main frame.
External Tally Expansion Module
PSWL-576
Provides for tally expansion modules which reside in the External Tally Expansion Frame, PSWL-575. A maximum of three modules can reside in one tally expansion frame.
K-Scope Interface
K-Scope to Model 3000/4000 Interface Kit
DPM-1305
15
Model 4000
Control Panel Redundant Power Supply
Electronics Frame Redundant Power Supply
Manuals
16
Ordering Guide
Control Panel Redundant Power Supply Provides back-up power to the 4000 control panel. It is designed to protect against a line failure or power supply failure.
Control Panel Redundant Power Supply for -2 Systems
PSWL-580-2
Control Panel Redundant Power Supply for -3 System
PSWL-580-3
Control Panel Redundant Power Supply for -3T System
PSWL-583
Electronics Frame Redundant Power Supply Provides back-up power to the Model 4000 signal system. It is designed to protect against a power supply failure.
Electronics Frame Redundant Power Supply for -2 Systems Electronics Frame Redundant Power Supply for -3 System
PSWL-581
Model 4000 Manual Set (all models)
TP0789-00 A1
4000 Installation & Service
TP0621-02 A1
4000 Operation Reference
TP0764-00 A1
4000 User Guide
TP0790-00 A1
4000 Drawings Manual
TP0624-01 A1
4000 Parts List
TP0623-01 A1
PSWL-581-3
Model 4000
Ordering Guide
TECHNICAL SPECIFICATIONS Specifications are subject to change without notice
Power Requirements
Dimensions
Switcher Power Supply Consumption: 1600 Watts (max) 1200 Watts (typical) Voltage: 176-264 VAC Frequency4 7-63 Hz
Switcher Frame Height: 111.13 cm, 43.75" (25 RU) Width: 48.3 cm, 19.0" Depth: 57.35 cm, 22.58" Weight: 136kg, 300 lbs (max)
Control Panel Consumption: 300 Watts Voltage: 110/220 VAC (nom) Frequency: 47-63 Hz
Environmental Characteristics Operating ambient temperature: 0-40° C, 32-104° F Ambient temperature for specification: 20 -30° C (68-86° F) Relative Humidity: 95% max (non-condensing)
Power Supply: Height: 31.1 cm, 12.25" (7 RU) Width: 48.3 cm, 19.0" Depth: 55.88 cm, 22.0" Weight: 65 kg, 143 lbs
4000-3 Main Control Panel Height: 55.1 cm, 21.7" Width: 137.16 cm, 54" Depth: 21.9 cm, 8.625" Weight: 62.14 kg, 137 lbs 4000-3 Accessory Control Panel Height: 25.9 cm, 10.2" Width: 137.16 cm, 54" Depth: 16.5 cm, 6.5" Weight: 25.58 kg, 63 lbs
4000-2 Control Panel Height: 63.9 cm, 25.14" Width: 124.5 cm, 49" Depth: 20.3 cm, 8" Weight: 59kg, 130 lbs
17
Model 4000
Ordering Guide
MODEL 4000 VIDEO SPECIFICATIONS Analog Input Video Characteristics (Chroma Key Inputs) Characteristics
Specification
Video amplitude (Luminance
714 mV with/without setup or
channel) for primary inputs
700 mV without setup (with or without sync) (Each input selectable by CAV input)
Maximum luminance excursion relative to black level (before clipping)
+108 IRE peak positive -6 IRE peak negative
Video amplitude for color difference Chroma key and Analog inputs (100% saturated Bars)
Betacam ±467 mV MII 60 Hz ±324 mV MII 50 Hz ±350 mV SMPTE ±350 mV EBU ±350 mV (Each input selectable by CAV input)
Video amplitude for RGB Chroma Key and Analog Inputs
714 mV with/without setup or
Linear Key Amplitude
714 mV with/without setup or
700 mV without setup (with or without sync) (Each input selectable by CAV input)
700 mV without setup (with or without sync) (Each input selectable by CAV input) DC offset of blanking level
±2 Volts
Common mode hum (reference only)
<2.0 V p-p max
Differential mode hum
<1.0 V p-p max
Random noise
<-30 dB RMS relative to 1.0 V p-p
Analog Reference Input
Black (loop-through) (burst is not required)
Impedance (Chroma Key and Analog Inputs)
75 Ohms Terminating
Return loss
>40 dB to 5 MHz
Manual timing steps
18 nS (Chroma Key inputs)
Manual timing range
±20 nS
Common mode hum attenuation
>34 dB
18
Model 4000
Ordering Guide
Serial Digital Input Video Characteristics Characteristics
Specification
Channel Coding
Conforms to SMPTE RP-259M
Aux Data
Auxiliary data is blanked
Connector
BNC
Input Impedance
75 Ohms
Return loss
>15 dB from 5 MHz to 270 MHZ
Autotiming range
±22 µs (4000-2) ±13 µs (4000-3)
Maximum cable length
225 meters (738 feet)
Number of bits
10
Serial Digital Output Characteritics Characteristics
Specification
Rise and Fall Times (Between 20% and 80% amplitude points)
Between 400pS and 1.5 nS across 75 Ohm termination
Jitter
Timing of rising edges of data signal shall be within ±0.25 nSec of average timing of rising edges over a period on 1 line.
Channel Coding
Conforms to SMPTE RP-259M
Aux data
None
Connector
BNC
Output impedance
75 Ohms
Return loss
>15 dB from 5 MHz to 270 MHz
Output amplitude
800 mV p-p terminated
DC level on output
<50 mV
Number of bits
10
Number of outputs
2 (except Timed Aux Output which has one)
19
Model 4000
Ordering Guide
Analog Output Characteristics Characteristics
Specification
Output amplitude
1.0 V p-p nominal
DC on output blanking level
<50 mV
Output return loss
>34 dB to 5 MHz
Output isolation
>54 dB to 5 MHz
Output Y/C Timing error
<10 nS
Number of outputs
2 (RGB or Color Difference - SMPTE/EBU or Betacam)
Output amplitude
<50 mV
Output Y/C timing error
<10 nS
Number of outputs
1
Video System Characteritics (Analog In to Analog Out) Characteristics
Specification
Frequency response
±0.2 dB to 5 Mhz, -40dB at 8 MHz
Group delay error
±8nS to 5 Mhz
Field rate tilt
<0.25%
K Factor (2t Pulse)
<0.25%
K Factor (Bar)
<0.25%
K Factor (Pulse to Bar)
<0.25%
Signal/P-P Noise Ratio (unweighted, 5 Mhz bandwidth)
>60dB
Line time non-linearity
<0.5%
Gain stability
1%
Crosstalk
>50dB to 5 MHz
20
Model 4000
Ordering Guide
Video System Characteritics (Analog or Digital) Characteristics
Specification
Blanking Width
10.222 µS (525 line) 10.666 µS (625 line)
Number of quantization bits
10 minimum
Mix tracking error
0
Linearity during mix
Linearity is not affected by mix
Frequency response during mix
Response is not affected by mix
Path length
80 µS (4000-2) 90 µS (4000-3)
Rounding method (digital only)
Adaptive Bit Reduction ™ (Patent Pending)
Environmental Characteritics Characteristics
Specification
Operating ambient temperature
0 - 40° C (32-104° F)
Ambient temperature for specifications
20-30° C (68-86° F)
Relative humidity
95% max (non-condensing)
21
Model 4000
Ordering Guide
TEKCARE SERVICE PRODUCTS TekCare is a comprehensive portfolio of software and hardware support services designed to ensure that you get the best performance from your Tektronix Video and Networking Products. Services include complimentary basic support, hotline support, extended warranties, on-site service coverage, installation
22
support, customer training, and software update support. Each service can be customized to meet specific organization and system requirements. With TekCare, Tektronix offers a level of support and satisfaction that only a worldwide service and support organization can deliver.
For details, phone Service Sales at 1-800-547-8949 then press 3 and 1.
Model 4000
Ordering Guide
WARRANTY •
•
•
Tektronix warrants that the Video and Networking Division hardware products that it manufactures and sells, will be free from defects in materials and workmanship for a period ending at the earlier of one (1) year from the date of installation or fifteen (15) months from the date of shipment. If any such product proves defective during this warranty period, Tektronix, at its option, either will repair the defective product or part without charge for parts and labor, or will provide a replacement in exchange for the defective product or part. In order to obtain service under this warranty, Customer must notify Tektronix of the defect before the expiration of the warranty period and make suitable arrangements for the performance of service. Customer shall be responsible for packaging and shipping the defective product or part to the service center designated by Tektronix, with shipping charges prepaid by Customer. Tektronix shall pay for the return of the product to Customer. During the first ninety (90) days of the warranty period, warranty service will include (i) reasonable telephone support during Tektronix normal business hours to
implied for such products and software. Additional copies of such warranties and software license agreements may be obtained by contacting Tektronix VND Contract Administration Department.
assist with advanced level problem resolution and (ii) replacement of defective modules by advance shipment. •
•
This warranty shall not apply to any defect, failure or damage caused by improper use or improper or inadequate maintenance and care. Tektronix shall not be obligated to reimburse Customer for service provided by personnel other than Tektronix representatives or to furnish service under this warranty a) to repair damage resulting from attempts by personnel other than Tektronix representatives to install, repair or service the product; b) to repair damage resulting from improper use or connection to incompatible equipment; or c) to service a product that has been modified or integrated with other products when the effect of such modification or integration increases the time or difficulty of servicing the product. Certain products and software supplied by Tektronix and manufactured by others may be subject to the respective manufacturer’s warranty and software license agreement copies of which are provided with the product. Tektronix assumes no warranty obligation either express or
•
THIS WARRANTY IS GIVEN BY TEKTRONIX WITH RESPECT TO THE PRODUCTS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED. TEKTRONIX AND ITS VENDORS DISCLAIM ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. TEKTRONIX’ RESPONSIBILITY TO REPAIR OR REPLACE DEFECTIVE PRODUCTS IS THE SOLE AND EXCLUSIVE REMEDY PROVIDED TO THE CUSTOMER FOR BREACH OF THIS WARRANTY. TEKTRONIX AND ITS VENDORS WILL NOT BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES IRRESPECTIVE OF WHETHER TEKTRONIX OR THE VENDOR HAS ADVANCE NOTICE OF THE POSSIBILITY OF SUCH DAMAGE.
23
MODEL 4000-2 OPTION CONFIGURATION DIAGRAM
A Video/Key B Video/Key Key 1 Video/Key
B11, B14
A6 M/E 1 Keyer 1
Borderline Included
A7 M/E 1 Keyer 2
Borderline PSWL-521
Key 2 Video/Key Serial Digital Input Auto Timed C16 Serial Digital Input Module
A Video/Key B Video/Key Key 1 Video/Key
A3, A4, A5
Borderline Included
Mixer Interface Video/Key
1-8 A12 M/E 2 Keyer 2
Included C15 Serial Digital Input Module
A11 M/E 2 Keyer 1
Borderline PSWL-521
Key 2 Video/Key 9-16
Included 17-24
VIDEO CROSSPOINT MATRIX
C14 Serial Digital Input Module PSWL-201-2 Analog Input Fixed Timed D17 D16 D15 D14 D13
CAV Input Module Set 4000-202-2 CAV Input Expansion 4000-203 CAV Input Module Set 4000-202-2 CAV Input Expansion 4000-203 CAV Input Module Set 4000-202-2
C13 Serial Digital Input Module PSWL-201-2 C12 Serial Digital Input Module
33-40
PSWL-201-2 C11 Serial Digital Input Module
41-48
C10 Serial Digital Input Module
B12, B13
Aux 1 Video/Key Aux 2 Video/Key Aux 3 Video/Key Aux 4 Video/Key
Effects Send Included
M/E 1 Video/Key M/E 2 Video/Key F/F Video/Key Aux 9A/B Aux 5A/B Aux 6A/B Aux 7A/B Aux 8A/B
PSWL-201-2
D12 CAV Input Expansion PSWL-201-2 4000-203 D11 CAV Input Module Set C8 Serial Digital 4000-202-2 Input Module D10 CAV Input Expansion PSWL-201-2 4000-203
D9
25-32
49-56
A16
Dual DSK 57-64
Program Video/Key Preset Video/Key DSK 1 Video/Key DSK 2 Video/Key
1
A14
Borderline Included A15
Borderline PSWL-521
Program/Preset Mixer Look Ahead PVW Included Sec Wipe Gen 4000-515
Black Background 1 Background 2 Test
Chroma Key Input 2 PSWL-530-2
Chroma Key Formats: RGB YUV SMPTE Beta MII
D8
3
Chroma Key Input
M/E 1 Chroma Keyer
B4
4 PSWL-530-2 D7
Included
5
M/E 2 Chroma Keyer
Chroma Key Input
Tally Expansion Frame PSWL-575
D1
Tally Exp. Module PSWL-576
1
Tally Exp. Module PSWL-576
1
Tally Exp. Module PSWL-576
1
4000-570-2 67
B5
6 PSWL-530-2 PSWL-531
Tally Output Module (installed in 4000 frame) Note: Tally Output Module and Serial Digital Output Module in this slot (D1) are mutually exclusive)
67
67
Control Panel Redundant Power Supply PSWL-580-2
A8 M/E 1 Mixer C17
Sec Wipe Gen PSWL-510-2
Analog Output
Look Ahead PVW Included
DSK PGM Video Switched Preview
(part of base system)
A13 M/E 2 Mixer
D6
Sec Wipe Gen PSWL-510-2 Digital Serial Output
Look Ahead PVW Included
Mask Switched Preview DSK Program Video DSK Program Key M/E 1 Program Video M/E 1 Program Key/Clean Feed M/E 2 Program Video M/E 2 Program Key/Clean Feed
Included D4
Aux 1 A/B Video/Key Aux 2 A/B Video/Key Aux 3 A/B Video/Key Aux 4 A/B Video/Key
Digital Serial Output
M/E 1 Video/Key M/E 2 Video/Key F/F Video/Key
Aux/Effects Send Bus 1A Video Aux/Effects Send Bus 1B Key Aux/Effects Send Bus 2A Video Aux/Effects Send Bus 2B Key Aux/Effects Send Bus 3A Video Aux/Effects Send Bus 3B Key Aux/Effects Send Bus 4A Video Aux/Effects Send Bus 4B Key
Included Aux 9A/B Aux 5A/B Aux 6A/B Aux 7A/B Aux 8A/B
D5
Digital Serial Output
DSK Video and Key PGM/PST Preview Video
M/E 1 Preview/Look-Ahead Video M/E 2 Preview/Look-Ahead Video DSK Preview/Look-Ahead Clean Feed Video PGM/PST Preview Video Aux Bus 9A Video (untimed) Aux Bus 9B Vid/Key (untimed)
Clean Feed/DSK PSWL-301 D3
D3
Maskstore 4000-500
Digital Serial Output (untimed)
Digital Serial Output (timed)
PSWL-301
PSWL-304-2
B15
Framestore (Video/Key) Included Black Background 1 Background 2 Test
A17
Mask
Preview Black Test & Bkg Gen
Switched Preview M/E 1 Preview M/E 2 Preview
Safe Title and Action Generator
DSK Preview
D1
Digital Serial Output
PSWL-301 Analog Reference
A9
Clocks to all boards Sync Generator
Serial Digital Reference
Signal System Redundant Power Supply PSWL-581
Video Timing Signals
Aux Bus 5A Video Aux Bus 5B Video/Key Aux Bus 6A Video Aux Bus 6B Video/Key Aux Bus 7A Video Aux Bus 7B Video/Key Aux Bus 8A Video Aux Bus 8B Video/Key
Explanation: The alpha numeric designation in the blocks, i.e. A17, designate the frame location of the board.
Framestore Video Framestore Key Note: Tally Output Module and Serial Digital Output Module in this slot (D1) are mutually exclusive)
MODEL 4000-3/3T OPTION CONFIGURATION DIAGRAM
A Video/Key B Video/Key Key 1 Video/Key
B11, B14
A6 M/E 1 Keyer 1 Borderline
Included
A7 M/E 1 Keyer 2
Key 2 Video/Key Serial Digital Input Auto Timed C16 Serial Digital Input Module
A3, A4, A5 B2
Key 2 Video/Key 9-16
A Video/Key B Video/Key Key 1 Video/Key
VIDEO CROSSPOINT MATRIX
17-24
4000-201-3 Analog Input Fixed Timed
C13 Serial Digital Input Module
4000-201-3 D17 C12 CAV Input Module Set Serial Digital 4000-202-3 Input Module D16 CAV Input Expansion 4000-201-3 4000-203 D15 C11 CAV Input Module Set Serial Digital 4000-202-3 Input Module D14 CAV Input Expansion 4000-201-3 4000-203 D13 C10 CAV Input Module Set Serial Digital 4000-202-3 Input Module D12 CAV Input Expansion 4000-201-3 4000-203 D11 C8 CAV Input Module Set Serial Digital 4000-202-3 Input Module D10 CAV Input Expansion 4000-201-3 4000-203
25-32
33-40
41-48
Chroma Key Input
Borderline
Included
Mixer Interface Video/Key
Borderline
PSWL-521 B7 M/E 3 Keyer 1 Borderline
Included B 8 M/E 3 Keyer 2 Borderline
Key 2 Video/Key
PSWL-521
Aux 1 Video/Key Aux 2 Video/Key Aux 3 Video/Key Aux 4 Video/Key
Borderline Key Edge Generator
B12, B13
Effects Send Included
M/E 1 Video/Key M/E 2 Video/Key M/E 3 Video/Key F/F Video/Key Aux 9A/B Aux 5A/B Aux 6A/B Aux 7A/B Aux 8A/B
49-56
Aux 9A/B
Dual DSK 57-64
Program Video/Key Preset Video/Key DSK 1 Video/Key DSK 2 Video/Key
1
D9
A11 M/E 2 Keyer 1
A12 M/E 2 Keyer 2
Included C14 Serial Digital Input Module
Borderline
PSWL-521
1-8
Included C15 Serial Digital Input Module
A Video/Key B Video/Key Key 1 Video/Key
A14
A16
Borderline
Look Ahead PVW
Included A15
Included Program/Preset Mixer
Borderline
PSWL-521
Black Background 1 Background 2 Test
2
4000-530-3 Tally Expansion Frame PSWL-575
3
D8
Chroma Key Formats: RGB YUV SMPTE Beta MII
Chroma Key Input
B4 4
4000-530-3
M/E 1 Chroma Keyer Included
5
D7
Chroma Key Input
C5
Tally Exp. Module PSWL-576
1
Tally Exp. Module PSWL-576
1
Tally Exp. Module PSWL-576
1
Tally Output Module (installed in 4000 frame) Included
67
B5 6
M/E 2 Chroma Keyer
4000-530-3 PSWL-531 B6
M/E 3 Chroma Keyer PSWL-531
67
67
Control Panel Redundant Power Supply PSWL-580-3
A8
M/E 1 Mixer
Sec Wipe Gen PSWL-510-3 Look Ahead PVW Included C17
A13 M/E 2 Mixer
Analog Output
Sec Wipe Gen PSWL-510-3
(part of base system)
Look Ahead PVW Included B9
DSK PGM Video Switched Preview
D6
M/E3 Mixer
Sec Wipe Gen PSWL-510-3
Digital Serial Output
Look Ahead PVW Included
Mask Switched Preview DSK Program Video DSK Program Key M/E 1 Program Video M/E 1 Program Key/Clean Feed M/E 2 Program Video M/E 2 Program Key/Clean Feed
Included D4
Aux 1 A/B Video/Key Aux 2 A/B Video/Key Aux 3 A/B Video/Key Aux 4 A/B Video/Key
Digital Serial Output
M/E 1 Video/Key M/E 2 Video/Key M/E 3 Video/Key F/F Video/Key
Aux/Effects Send Bus 1A Video Aux/Effects Send Bus 1B Key Aux/Effects Send Bus 2A Video Aux/Effects Send Bus 2B Key Aux/Effects Send Bus 3A Video Aux/Effects Send Bus 3B Key Aux/Effects Send Bus 4A Video Aux/Effects Send Bus 4B Key
Included D5
Aux 5A/B Aux 6A/B Aux 7A/B Aux 8A/B
Digital Serial Output
DSK Video and Key PGM/PST Preview Video Clean Feed/DSK
PSWL-301
B16
D2 D3
D3
Digital Serial Output (untimed)
Maskstore 4000-500
Digital Serial Output (timed)
B15
Framestore
Aux Bus 5A Video Aux Bus 5B Video/Key Aux Bus 6A Video Aux Bus 6B Video/Key Aux Bus 7A Video Aux Bus 7B Video/Key Aux Bus 8A Video Aux Bus 8B Video/Key
PSWL-301 PSWL-304-3
Included Black Background 1 Background 2 Test
M/E 1 Preview/Look-Ahead Video M/E 2 Preview/Look-Ahead Video M/E 3 Preview/Look-Ahead DSK Preview/Look-Ahead DSK Clean Feed Video PGM/PST Preview Video M/E 3 Program Video M/E 3 Program Key/Clean Feed
A17
Mask
Preview Black Test & Bkg Gen
Switched Preview M/E 1 Preview M/E 2 Preview
Safe Title and Action Generator
M/E 3 Preview
D1
Digital Serial Output
Aux Bus 9A Video (untimed) Aux Bus 9B Vid/Key (untimed) Framestore Video Framestore Key
DSK Preview
PSWL-301 Analog Reference
A9
Clocks to all boards Sync Generator
Serial Digital Reference
Electronics Frame Redundant Power Supply PSWL-581-3
Video Timing Signals
Control Panel Redundant Power Supply (-3T Panel Only) PSWL-583
Explanation: The alpha numeric designation in the blocks, i.e. A17, designate the frame location of the board.
For further product and service information or the sales office nearest you, please contact: Tektronix, Inc. Video and Networking Division P.O. Box 500 M.S. 58-965 Beaverton, OR 97077-0001 USA
Copyright © Tektronix, Inc. All rights reserved. Printed in the U.S.A. TEKTRONIX is a registered trademark and Grass Valley is a trademark of Tektronix, Inc. All registered trademarks and trademarks are property of their respective holders.
12/97 LM2945R1 2WW-2701-8
No. America Phone: (800) 547-8949 No. America fax: (503) 627-7275 Europe fax: 33 (1) 69 07 0937 Asia fax: +852 2802 2996 Japan fax: +81 (3) 5992 9377 Latin America fax: (305) 477-5385 InfoFax: (800) 704-8843 (North America) URL: http://www.tek.com/VND
