Transcript
GYROLOCK
User Guide
For video projectors up to 20Kg Ceiling Suspended - 12Kg Wall Mounted. Gyrolock units may be fixed to normal or sloping ceilings, with the telescopic section remaining vertical for correct video projector support. When used as a wall mount the telescopic section works as an angled support arm allowing clearance for the tilt and swivel movements. Units can also be base mounted for rear projection or other applications. Our range of projector adapter plates (order code GAP) is constantly updated - see current list for latest projectors covered.
1 2
SAFETY We recommend installation by a Qualified Tradesperson, SAFETY. using masonry plugs or other reliable fixings to ensure safe installation. - Consult your builder or architect if in doubt.
Standard Gyrolock Unit GK1
CEILING INSTALLATION - STANDARD GK1 UNIT Establish the reuired projector to screen distance and fix the unit through the holes provided in the mounting plate (1). Adjust the telescopic section (2) as required and fully tighten screws. PROJECTOR MOUNTING Fix the adapter plate (3) to the video projector using the screws provided. Raise the projector into position and engage it into the Trilok bayonet (4). Rotate the projector a half turn (180 degrees) then tighten the safety screw (5) into the arrow head void. Hand tighten the two clamp screws (6) to lock the projector in place.
6
5
ADJUSTMENT Using the pan, tilt and screen levelling functions adjust the projector alignment. Finally tighten all dome headed screws using the allen key provided. RANGE OF DIFFERENT DROP LENGTHS The GK2 installers kit comes with alternative telescopic sections which can be used in any combination to give 23-70cm adjustment, intended particularly when working within suspended ceiling voids.The GK3 version has a longer telescopic section for use with high ceilings. The GK4 version uses a CP1 Ceiling plate and chrome column (cut to length), for installations requiring long drops - there is no telescopic section with this model. CLOSE CEILING INSTALLATION Remove the telescopic section (2) and reconnect the bottom half of the Gyrolock unit directly to the mounting plate (1). Follow projector mounting and alignment instructions to continue installation.
Shown adapted for close ceiling use
Trilok Equipment Docking System
Adapter plate typical adapter plate shown
CAMERA SCREW FITTING - GK0 For prtojectors with Camera Screw fittings, remove knurled screw assembly (7) and fix to projector. Ensure locking ring (8) is loose and refit assembly and projector by sliding into position as shown. Tighten locking ring (8) to secure. Follow adjustment instructions to continue installation.
GK0 is restricted to 12Kg Max weight.
WALL MOUNTED INSTALLATION Set the Gyrolock unit so that it appears like the wall version illustrated with the short telescopic mast (2) sloping as shown.
12 Kg Max Weight
IMPORTANT, use only as illustrated with the standard short telescopic mast (2) acting as the support arm.
BASE MOUNTED INSTALLATION Remove the telescopic section (2) from the mounting plate bracket (1) and reset it into the slots as illustrated. Refit and fully tighten the dome headed screws with the allen key provided. Follow projector mounting and adjustment instructions to continue installation.
Follow projector mounting and adjustment instructions to continue installation. Shown set for wall mounting
Shown inverted for base mounting
UNICOL, Green Road, Oxford, OX3 8EU, UK. t: +44(0)1865 767676 f: +44(0)1865 767677 e:
[email protected]
www.unicol.com
4
3
8 7
TETHERLOC ANTI-THEFT KIT
For Gyrolock GK1, 2 & 3 Ref: UNICOL GT40 GT80 GT130
Add this easily fitted kit to your Gyrolock mount unit. Tough steel cable system blocks access to both projector and mount fixing screws in the ceiling, yet allows full movement of projector during set-up. Current GAP adapter plates are designed ready to take the Tetherloc System, which works with most projector models listed. Long series cable versions also available.
Gyrolock Fixing Plate
4 Thread cut end of cable through retaining slots in security top plate
1
Fit Tetherloc fixing plate to Gyrolock fixing plate using the fastenings that hold the Gyrolock to the ceiling, wall, or desktop
5 Slot lock cover into security top plate and lock to complete installation
2
Fit Gyrolock Adapter Plate (GAP) to projector by screwing fixing screws through security block. Fit Projector and GAP to Gyrolock.
3 Thread cable through security block
UGT0514
