Transcript
HALL 05-6043-BW-82U
Design by NAHTRANG DISSENY TECHNICAL CHARACTERISTICS
The photograph may not match the reference exactly. Please read the product description to identify the finish.
Type:
Wall fixture
RPM:
-
Light source 1: Bulb specified at the product label
1 x LED 2.2W Warm White - 2700K (N) 174.8 lm CRI 80
Light source 2: Bulb specified at the product label
1 x E26 60W 0 lm(N)
Location:
DRY
Total power consumption (W):
3.5W
Angle of the optics / Reflector:
30º
Voltage / Frequency:
120-277V/50-60Hz
Warranty:
2
Net Weight (Lb):
0
CFM:
-
355º
0º a 90º
Download photometric file .ldt /.ies
MATERIALS / FINISHES Structure material: Aluminium Structure finish:
Matt white
GEAR Multi-voltage electronic gear included (Yes)
LEDS-C4 reserves the right to make the necessary technical changes they deem adequate, in order to improve the features of the product. Please consult the sales team to clarify any doubt.
(+34) 973 468 100
[email protected] www.leds-c4.com
Accessoris PAN-194-AJ Shade,grey, Ø220mm Diffuser material:
Fabric shade
Diffuser finish:
Opera grey
IP20 PAN-177-BY Shade, oval shape, beige fabric, 285x150x150mm Structure material:
Steel
Diffuser material:
Fabric shade
Diffuser finish:
Sandblasted
PAN-177-14 Shade, oval shape, white, 285x150x150mm Structure material:
Steel
Diffuser material:
Fabric shade
Diffuser finish:
White
PAN-157-BY PANTALLA DE TELA ARENA Structure material:
Steel
Diffuser material:
Fabric shade
Diffuser finish:
Sandblasted
IP20
LEDS-C4 reserves the right to make the necessary technical changes they deem adequate, in order to improve the features of the product. Please consult the sales team to clarify any doubt.
(+34) 973 468 100
[email protected] www.leds-c4.com
PAN-157-14 Shade, white, Ø200mm Structure material:
Steel
Diffuser material:
Fabric shade
Diffuser finish:
White
IP20 PAN-161-14 Structure material:
Steel
Diffuser material:
Fabric shade
Diffuser finish:
White
IP20 PAN-161-BY Structure material:
Steel
Diffuser material:
Fabric shade
Diffuser finish:
Sandblasted
IP20 PAN-179-14 Shade, white, 180x186x150mm Structure material:
Steel
Diffuser material:
Fabric shade
Diffuser finish:
White
IP20
LEDS-C4 reserves the right to make the necessary technical changes they deem adequate, in order to improve the features of the product. Please consult the sales team to clarify any doubt.
(+34) 973 468 100
[email protected] www.leds-c4.com
PAN-179-BY Shade, beige fabric, 180x186x150mm Structure material:
Steel
Diffuser material:
Fabric shade
Diffuser finish:
Sandblasted
IP20 PAN-176-14 Shade, white, 182x170x150mm Structure material:
Steel
Diffuser material:
Fabric shade
Diffuser finish:
White
PAN-176-BY Shade, beige fabric, 182x170x150mm Structure material:
Steel
Diffuser material:
Fabric shade
Diffuser finish:
Sandblasted
PAN-158-J6 Structure material:
Steel
Diffuser material:
Ribboned shade
Diffuser finish:
Brown
IP20
LEDS-C4 reserves the right to make the necessary technical changes they deem adequate, in order to improve the features of the product. Please consult the sales team to clarify any doubt.
(+34) 973 468 100
[email protected] www.leds-c4.com
PAN-162-J6 Structure material:
Steel
Diffuser material:
Ribboned shade
Diffuser finish:
Brown
IP20 PAN-187-20 Shade,beige, pleated, 180x186x150mm Structure material:
Steel
Diffuser material:
Ribboned shade
Diffuser finish:
Beige
IP20
LEDS-C4 reserves the right to make the necessary technical changes they deem adequate, in order to improve the features of the product. Please consult the sales team to clarify any doubt.
(+34) 973 468 100
[email protected] www.leds-c4.com
LEDS, C4 S.A. CIF/VAT: A-59.410.910 C/ Afueras s/n -TORA- 25750 (LLEIDA) SPAIN TEL: 34 (73) 46 81 02 FAX: 34 (73) 46 81 06
SHEET: 1/2 EDITION: 01
REF: 05-6043U
FIGURE Nº 1. UNPACK THE FIXTURE: CHECK THE CONTENTS OF THE BOX. YOU SHOULD RECEIVE:
FIGURE 6
FIGURE Nº 1. DÉBALLER LE PLAFONIER: VÉRIFIER LE CONTENU DU CARTON, VOUS DEVEZ RECEVOIR:
FIGURE 7
INSTALLATION INSTRUCTIONS FOR HANGING FIXTURES FIGURE 3, 4 AND 5 MOUNTING HARDWARE. NOTE: TEST THE CONNECTOR BY GENTLY PULLING IT. IF IT PULLS OUT THE CONNECTION, TRY AGAIN TILL YOU HAVE A FIRM CONNECTION. MAKE SURE NO BARE STRANDS OF WIRE STICK OUT FROM UNDER THE CONNECTORS. WHITE OR MARKED WIRE FROM FIXTURE
WHITE WIRE FROM OUTLET BOX FIGURE 3
BLACK OR UNMARKED WIRE
BLACK FIGURE 4
FIGURE 5
INSTRUCTIONS D'INSTALLATION POUR PLAFONIERS FIGURE 3, 4 ET 5 MONTAGE DE L'ÉQUIPE. IMPORTANT: ESSAYER DE TIRER LE CÂBLE D'ALIMENTATION DOUCEMENT.S'IL SORT DE LA CONNECTION, IL FAUDRAIT ASSURER QUE LA CONNECTION SOIT FERME. S'ASSUSER QUE LES FILS DES CÂBLES NE SONT PAS À DÉCOUVERT DU CONNECTEUR. CÂBLE BLANC OU MARQUÉ DU PLAFONIER
CÂBLE BLANC DE LA BOÎTE FIGURE 3
CÂBLE NOIRE OU NOU-MARQUÉ
FIGURE 4
NOIRE
FIGURE 5
CAUTION:
ATTENTION:
"Warning", "This product is to be installed by a qualified electrician only." "Suitable for dry locations only"
"Attention", le raccordement électrique sera effectué par un téchnicien électricien qualifié" "Adéquat seulement en lieux secs."
CAUTION: 1.- Wrong lighting installation can be dangerous for your safety. 2.- Before starting, disconnect the power by turning off the general switch of the electric installation. 3.- Install light bulbs (not provided) that must not exceed markings on the fixture. 4.- To change the bulbs, disconnect the power by turning off the general switch and wait for the bulbs cool down. INSTALLATION: 1.- Make electrical connections, carefully read the Electrical Connection section. 2.- Assemble lighting onto the outlet box as shown on fig. 6, & 7. ELECTRICAL CONNECTIONS: (See fig. 3,4 y 5) 1.- Connect the white wire from the fixture to the white wire of the electric installation. 2.- Connect the black wire from the fixture to the black wire of the electric installation. 3.- Connect the grounding conductor from the fixture to the grounding wire of the electric installation. 4.- Spread out the electrical wires so that the black ones are on one side of the outlet box and the white ones are on the other side, and carefully introduce them into the outlet box.
ATTENTION: 1. Une mauvaise installation peut compromettre votre sécurité. 2. Déconnecter la tension du réseau d'alimentation avant de réaliser toute opération. 3. Installer les ampoules (non fournies), ne pas utiliser d'ampoules d'un autre type ou d'une puissance supérieure à celle indiquée sur l'étiquette de la lampe. 4. Pour changer les ampoules, déconnecter la tension du réseau d'alimention et laisser refroider les ampoules. INSTALLATION: 1. Connecter au réseau, lire attentivement la section de "Raccordements électriques" 2. Installer l'appareil à la boîte de distribution comme indiqué dans les dessins 6 et 7. RACCORDEMENTS ÉLECTRIQUES (dessins 3,4 et 5) 1. Connecter le câble blanc de l'appareil au câble blanc de l'installation électrique. 2. Connecter le câble noir de l'appareil au câble noir de l'installation électrique. 3. Connecter le câble conducteur de prise de terre au câble de prise de terre de l'installation électrique. 4. Distribuer les câbles pour que tout le câblage noir soit par dehors et le câblage blanc soit par dedans. Ajuster et immobiliser à la boîte sans coincer aucun câble.
LEDS, C4 S.A. CIF/VAT: A-59.410.910 C/ Afueras s/n -TORA- 25750 (LLEIDA) SPAIN TEL: 34 (73) 46 81 02 FAX: 34 (73) 46 81 06
SHEET: 2/2 EDITION: 01
REF: 05-6043U
1 1.2 1.1 ON
OFF
2
3
ON
OFF
