Transcript
Add-On -2
HANDLE BARS $150.95-H
Carbon Fibre/Tapered Aluminum Handlebars • 7075-T6 Heat treated aircraft tapered aluminum wrapped with a thin skin of Carbon Fibre • Tapered walled aluminum flexes to reduce rider fatigue and arm pump • Tapered wall construction offers the strongest snowmobile handlebar available. • Carbon fiber wrap acts as a barrier between the grip heater and aluminum to allow grips to get hotter. • Clamp surface is 1 1/8" and tapers down to 7/8" to fit controls and grips. • 1 1/8" oversized clamp kit or risers are required to mount to snowmobile. • Custom snowmobile specific bends offer more comfort than stock handlebars.
TCI Part # 781-4102 781-4104 781-4103 781-4101
Description Snow Carbon Tapered 10° Handlebar Snow Carbon Tapered 15° Handlebar Snow Carbon Tapered Race Handlebar Snow Carbon Tapered Back Country Handlebar
Width 800 mm 743 mm 760 mm 740 mm
Rise 0 mm 0 mm 3 mm Up Sweep 83 mm
Pullback 10° 15° 10° 14°
Tapered Aluminum Handlebars • • • • • • • •
$ 89.95-H
7075-T6 Heat treated aircraft tapered aluminum. Tapered walled aluminum flexes to reduce rider fatigue and arm pump. Tapered wall construction offers the strongest snowmobile handlebar available. Clamp surface is 1 1/8" and tapers down to 7/8" to fit controls and grips. Black snowmobile bar pad included. 1 1/8" oversized clamp kit or risers are required to mount to snowmobile. Custom snowmobile specific bends offer more comfort than stock handlebars. Gunmetal color only.
TCI Part # 781-4015 781-4016 781-4017 781-4004
Description Snow Tapered 10° Handlebar Snow Tapered 15° Handlebar Snow Tapered Race Handlebar Snow Tapered Back Country Handlebar
Width 800 mm 743 mm 760 mm 740 mm
Rise 0 mm 0 mm 3 mm Up Sweep 83 mm
Pullback 10° 15° 10° 14°
Chromoly Handlebars • • • •
$50.95-H
4130 Chromoly steel. Snowmobile specific bends offer better comfort. Fits 7/8" handlebar clamps. No rise flat design offers more surface area for controls.
• Guide lines on ends of bar for narrowing handlebar to a custom width. • Black only.
TCI PART # 781-4115 781-4116 781-4117
DESCRIPTION Chromoly 10° Handlebar Chromoly 15° Handlebar Chromoly Race Handlebar
Width 800 mm 743 mm 760 mm
Rise 0 mm 0 mm 3 mm Up Sweep
10° Bend
15° Bend
Back Country Bend
Race Bend
Toll Free 1 800 661 9438
www.transcanimports.com
Pullback 10° 15° 10°
Add-On -3
HANDLE BARS 2014 Aluminum Handlebar 5" Rise
781-7220
$79.95-H
• 2014 heat treated aluminum has superior strength to resist bending. • Snowmobile specific 10 degree bend offers increased comfort. • Fits 7/8" handlebar clamps. • Crossbar has pre drilled holes for stud mounted type of mountain /grab strap. • Guide lines on ends of bar for narrowing handlebar to a custom width. • Black only • Black Bar pad included
SPI Aluminum Riser Bars
$45.95-J
• 7/8" • Black
781-3004 - 4.5" Rise
781-3006 - 6" Rise
SPI Chromoly Pullback Handle Bar
781-3100
$29.95-J
706-7600
$57.95-H
• Pullback 10°, Length 813 mm, rise 0 mm • 7/8" • Black
V-Max Mountain Bars • Fits Yamaha T-Bars • Unpainted
HANDLEBAR RISERS UHMW 2" Plastic Risers by DMC Lightweight and Super strong U.H.M.W Plastic make these an excellent choice A/C (pre 2000) & Polaris
A/C (2000 & newer)
Ski-Doo
Yamaha
Retail
757-2302
757-2305
757-2332
757-2342
$29.95-H
SPI Articulating Handlebar Risers • Universal to fit all makes and models • CNC Machined from billet 7075 T-6 aluminum
TCI PART # 781-5532 781-5534 781-5535
Description 2" Riser 4" Riser 5" Riser
Toll Free 1 800 661 9438
Retail $79.95-H $79.95-H $71.95-H
www.transcanimports.com
Add-On -3
HANDLEBAR RISERS Rotating RAD Risers • Universal Rotating Risers to fit all makes and models • Machined out of T-6061 aluminum for strength • Gives the aggressive rider choice of custom bar position
Fits 1 1/8" Tapered Bar 2" 3" 4" 6" 8"
757-2112 757-2113 757-2114 757-2116 757-2118
Fits 7/8" to 7/8" Bar
$130.95-H $130.95-H $142.95-H $142.95-H $142.95-H
2" 3" 4" 6" 8"
757-2102 757-2103 757-2104 757-2106 757-2108
$105.95-H $105.95-H $124.95-H $124.95-H $134.95-H
Angle Handlebar Risers • • • • • • • •
$77.95 pair - H
Precision angle moves handlebars straight up from center of steering post. Offers increased comfort and feel for aggressive mountain riding or trail riding. Fits flat style steering posts only. Fits stock 7/8" handlebars. 6061 T-6 aluminum construction. Universal type design fits multiple applications. Simple bolt on design installs in minutes.
Most snowmobiles will allow 2" or 3" of rise without extending cables or wiring. • Anodized Silver or Black finish.
30° Fits:
All Arctic Cat (except M-Series Chassis) All Polaris (Except 2009) Ski-Doo Rev and ZX Chassis Yamaha Mtn Max , SX, SRX, Viper
15° Fits:
All Arctic Cat M-Series and Crossfire Chassis 2009 IQ Polaris with flat style steering posts.
3" Silver 30° 781-5513
3" Black 30° 781-5514
3" Silver 15° 781-5517
3" Black 15° 781-5518
Pivoting Handlebar Risers
$89.95 pair - H
• Dual pivoting adjustability allows you to position handlebars where you want them. • Inserts that allows risers to fit stock 7/8" handlebars or oversize 1 1/8" handlebars. • Extruded from 6061 T-6 Aircraft aluminum to resist bending or twisting. • Machined to reduce weight • Rise is measured from center to center. • Black, anodized finish • Sold in pairs *
Check the length of the existing cables/brake lines to ensure proper fit - extensions may be required.
*
For use with pivot style steering posts or steering posts with adapter tubes. (See page 4)
2" Riser 781-5502
3" Riser
781-5503
4" Riser 781-5504
5" Riser 781-5505
Toll Free 1 800 661 9438
6" Riser 781-5506
7" Riser 781-5507
8" Riser 781-5508
9" Riser 781-5509
www.transcanimports.com
10" Riser 781-5510
Add-On -5
RSI Steering Post Pivot Tube
781-5400
$14.95-H
• 5 1/2" tube converts stock flat style steering post to a pivot style steering post when using a pivoting style handlebar riser. • Super strong Chromoly Steel. • Clamps into stock handlebar clamps or any 7/8” handlebar clamps. • Positions pivoting style risers on outside of stock handlebar clamps. • Anodized black finish. *
Steering Post Pivot Tube
Double check handlebar clamping surface width to verify riser/pivot tube combination fits correctly.
STEERING POST PIVOT ADAPTER • Converts a flat steering post to a double pivot style post. • Simple bolt on design. • Adds 3/4" of rise. • Works with most 2 piece aftermarket risers.
Steering Post Pivot Adapter
APPLICATION Arctic Cat Polaris Ski-Doo (Except Rev) Ski-Doo Rev Yamaha *
TCI PART# 781-5401 781-5402 781-5403 781-5405 781-5404
Since these pivot adapters put the risers on the outside of the steering post plate the widths of the clamping surface varies. Double check the clamp surface area width on your stock bars to make sure it is wide enough for the risers to clamp down on a flat surface and not into the curve of the handlebar. If the clamping surface is too wide for your stock bars you will need an RSI offset adaptor clamp kit.
Clamp Surface Minimums for RSI Risers:
Steering Post Offset Adapter Kit
RETAIL $24.95-H $24.95-H $24.95-H $24.95-H $24.95-H
Arctic Cat - 116 mm Ski Doo - 110 mm
Polaris - 116 mm Yamaha - 122 mm
RSI STEERING OFFSET ADAPTER KIT 781-5406
$41.95-H When using a RSI Pivot Adaptor and RSI Pivot Risers on a snowmobile with a flat style steering post, the Pivoting Risers often are positioned too wide to clamp on the stock handlebars properly. It make the Pivot Risers want to clamp on the bend portion of the handlebar which is not acceptable. These offset clamp adaptors will re-locate the handlebar clamps to the stock location and allowing you to use the RSI Pivoting Risers and Pivot Adaptor together on a flat style steering post with your stock handlebars. • Allows stock handlebars to be used with the RSI Pivot Risers and RSI Pivot Adaptor. • 6061 T-6 CNC Billet Aluminum construction. • Sold in pairs with mounting hardware.
Silver Handlebar Clamp Kit
RSI Oversize Handlebar Clamp Universal clamps allow 1-1/8” bars to be clamped to Snowmobiles • Works with PowerMadd and stock OEM Pivot style Riser Blocks as well as on Snowmobiles with flat style steering posts.
TCI PART # 781-5331 781-5332
COLOR Silver Black
RETAIL $41.95-H $41.95-H
Black Handlebar Clamp Kit
HANDLEBAR HOOKS Ultra Hooks
$32.95-H
• Molded from super-tough, unbreakable nylon • Will not rob heat from hand -warmers • Fits all standard OEM handlebars, including all 120cc mini sleds • 45°
Toll Free 1 800 661 9438
Blue
Green
706-5006
706-5005
www.transcanimports.com
TRANS CAN IMPORTS
Add-On -6
HANDLEBAR HOOKS RSI Billet Handlebar Hooks
$17.95-H/ea
• Easy bolt on design. • Extends handlebar for a more comfortable feel when leaning off of snowmobile. • Fits tapered aluminum and steel handlebars. • Allows extended length grips to be installed over the top for a seamless feel. • 7/8" Outside diameter is same size as handlebar diameter for a even seam. • Sold each
DESCRIPTION Long Hook Short Hook Long Hook Short Hook
FI Tapered Bar Tapered Bar 7/8" stock bar 7/8" stock bar
TCI PART 781-5301 781-5311 781-5322 781-5320
Stock 7/8" Bar/ Short Hook 781-5320
Tapered Bar/ Long Hook 781-5301
Handlebar End Hooks
706-2001 $31.95-H This unique device has been needed ever since snowmobiles have had a track and went over 25 mph! The handlebar Hook is designed to help prevent your hand from slipping off the handlebars. If you "hang out" on corners or side hill around mountains, the Handlebar Tool will help keep you on your sled with better control and safety. • Aluminum Wedge (diameter 0.69") • Kit includes 2 black aluminum hooks, 2 washers, 2 bolts
RSI Handguard Mounts • • • • •
710-3026
$60.95-H
Universal billet handguard mounts fit a wide variety of handguards Anti-Spin clips included prevent handguards from spinning down from hard bumps. Powder-coated black 2 piece handlebar clamp design installs in minutes. Offset angle positions handguards out so ample room is available when side hilling or reaching off the end of the handlebar. Prevents wrist hitting guards.
• Sold per pair
SPI Handguard Mount
706-7899
$32.95-J
Fits SPI and Sno Pro Handguards
SpeedGuard Chrome Hand Guards
$122.95-H
*
• Ride all day in thin gloves without suffering from popsicle fingers • Aluminum mounting hardware allows hand guards to be infinitely adjustable. • Custom molded from super-tough HDPE material. Please see our Essential Catalog for more hand guards
Chrome
Orange Chrome
706-7810
706-7822
Toll Free 1 800 661 9438
www.transcanimports.com
TRANS CAN IMPORTS
Add-On -7
HANDLEBAR PADS RSI Handlebar Pads • Designed specifically for snowmobiles. • Heavy duty outer nylon with TPR rubber logos will not separate in the coldest weather. • Hi Density closed cell foam will not absorb water. • Helps protect rider from sharp bolt edges on handlebar risers.
Bar Pad Large Black Bar Pad Large White Bar Pad Small Black Bar Pad Small White
781-4200 781-4201 781-4210 781-4211
SPI Mountain/Grab Bar • • • •
$24.95-H $24.95-H $24.95-H $24.95-H
706-8299
$13.95-H
706-8298
$7.95-H
More flexible than most flex-bars 390 mm NBR 85 degree hardness Includes universal u-bolt mounting hardware
Replacement Mounting Hardware
Ekholm Grab Extension $19.95-H The Mountain Grab Extension is no cheap screw-on extension. Made with the expertise you have come to expect from Ekholm. These extensions are inexpensive and yet offer the same advantage as mountain bars. The custom aluminum mount allows everything to remain stock. TCI PART # MODEL MFG 706-7910 706-7920 706-7930 706-7931 706-7941 706-7942 706-7942 706-7931 706-7931
Arctic Cat Polaris Ski-Doo Yamaha
Toll Free 1 800 661 9438
Ext, Wildcat, ZR All ”F” Series Chassis S2000 / ‘96 Summit Phazer / Exciter Vmax 4 ‘92-’97 Vmax 500/600 '94-'96 Vmax 500/600/700'97-'98 Venture ‘97-’98
www.transcanimports.com
