Transcript
HARTING Electronics GmbH & Co. KG D-32339 Espelkamp
Assembly instruction ENGLISH
HARTING RJ Industrial® Gigalink IP 67 Push Pull connector Part no.: 09 45 145 1500 (cable manager white) 09 45 145 1510 (cable manager blue)
Only a few steps are necessary in order to quickly and reliably attach an Industrial Ethernet cable to a HARTING RJ Industrial® Gigalink connector.
1. Fit the universal sealing ring to the cable sheath diameter which is used. Push the nut, thrust washer, sealing ring and housing over the cable sheath.
6. Cut the over standing ends of the wires in the way that no electrical shortcuts are possible. Excess end max. 0.3 mm.
7. Insert the cable manager into the data module adaptor and lock it with an audible click.
2. Strip the sheath and the braid. 40 – 42 mm
EIA / TIA 568 B
1
green / white
orange / white
2
green
orange
3
orange / white
green / white
4
blue
blue
5
blue / white
blue / white
6
orange
green
7
brown / white
brown / white
8
brown
brown
1
3
6
8
1
4
5
8
2
4
5
7
2
3
6
7
20 – 21 mm
white 3. Cut 7 - 8 mm of the sheath and push it up to the end of the braid.
9. Put on the upper shielding shell and press it over the cable screen. Afterwards put on the lower shielding shell and lock it with the upper shell with an audible click.
7 – 8 mm
Recommended cable types
l
EIA / TIA 568 A
8. Press down the cable fixing and lock it with an audible click.
47 – 50 mm
l
Pin
Back view of the cable manager
Description
The IP 67 data version in push pull housing is fitted with innovative housing locking technology. The housing of the connector is locked tightly to the coupling by means of a surrounding locking sleeve. The connector can be locked and unlocked using one hand and only a little force. In spite of its high degree of protection, the dimensions of the housing are very small. By this the HARTING RJ Industrial® Push Pull Category 6 is ideally suited to compact industrial applications that require 4 pair or Gigabit Ethernet wiring.
Pin assignment
HARTING RJ Industrial® Fast Ethernet cable, four pair, for flexible installation, cabling standard Category 5 acc. to ISO/IEC 11801, two wires twisted to a pair, four pairs twisted with shielding foil, 4 x 2 x AWG26/7. Part number 09 45 600 0103
4. Insert the wires pair wise up to the braid into the cable manager.
HARTING RJ Industrial® Gigalink Industrial Ethernet cable, four pair, for flexible installation, cabling standard Category 6 acc. to ISO/IEC 11801, two wires twisted to a pair, shielded, four pairs twisted with shielding, 4 x 2 x AWG26/7. Part number 09 45 0600 0500
5. Crimp the cable manager.
!
ATTENTION: Use only the HARTING RJ Industrial® crimp tool (part no. 09 45 800 0500)! Be aware to insert the cable manager up to the end into the tool.
10. Push the housing over the installed data module and lock it with an audible click.
11. Tighten the cable gland. We recommend to use an open box wrench with size 19 mm.
blue
Technical data Transmission properties in accordance with Category 6 ISO/IEC 11 801:2002 and EN 50173-1 Protection level
IP 67/65
Mating interface
RJ 45 in accordance with IEC 60603-7
Wire gauge data1)
AWG 26-24 stranded
Temperature range
-40 °C ... +70 °C
Cable sheath diameter
5.8 mm - 7.2 mm
Mating cycles
min. 750
Housing material
Thermoplastic, black UL 94-V0
1)
Details see technical data sheet
Version 1.0 05/2004 Errors and technical changes excepted.
