Transcript
HD-DVI Board The HD-DVI Board is a small form factor module for formatting and conversion of generic digital video streams to standard compliant formats. Different cables types are supported from the transmitter side including DVI and HDMI cable, coaxial cable and twisted pair LAN cable. The modules directly connect to the digital video interface of Sony’s FCB-H10 HDTV block camera and support 1080i/50Hz, 1080i/59,94Hz, 720p/50Hz and 720p/59.94Hz HDTV formats. As no analog to digital conversion is done on these modules, best image quality is guaranteed for the output signals.
Features + DVI compliant digital video output (HDTV over DVI) + Support of all HDTV formats of FCB-H10 + 1080i/50Hz, 1080i/59.94Hz, 720p/50Hz and 720p/59.94Hz + LVDS 4 link digital video input + Full digital signal processing chain for best image quality + Additional analog HDTV YPrPb output on analog pins of DVI-I connector + Pass through connector for camera power and RS232 serial control + Single power input for camera and module + Power requirements: 7V to 12V DC regulated / 2,3W + Tiny module size 44mm x 42mm x 1,6mm (width x height x thickness) + Three mounting holes, 2,5mm diameter + DVI cable length up to 12m
Block Diagram DIGITAL INPUT FROM CAMERA (10pin Micro Coax Connector)
Data_LVDS
Diff Rx
PLL w. VCXO
FPGA DESER DATA FORMATTER
Clk_LVDS
Diff Rx
DVI Transmitter
ENCODER
HD analog Y, Pb, Pr DVI-I OUTPUT Cable Conn.
0.5mm FLAT FLEX CABLE TO CAMERA
RS232 Rx Tx SD analog CVBS
24pin FFC Camera Conn.
RESET
LDO 12V DC input
DC/DC Converter
LDO ONBOARD DC SUPPLY VOLTAGES LDO LDO
HD-DVI Board Specification INPUTS: DATA CLOCK CAMERA RESET CONTROL Rx OUTPUTS: CONTROL Tx VIDEO (HD MODE)
VIDEO (SD MODE)
Onboard Connector 4 LINK LVDS (from Sony FCB-H10) LVDS (from Sony FCB-H10) LVTTL RS232
RS232 DVI, digital, 1080i or 720p, 59.94Hz or 50Hz analog Y, Pb, Pr (direct from camera, see camera data sheet for Y, Pb, Pr spec.) CVBS (direct from camera)
J2 Power, Signal and Control connector: Pin 1 = +8V DC typ. (7V to 12V range allowed) Pin 2 = +8V DC typ. (7V to 12V range allowed) Pin 3 = GND Pin 4 = RXD (serial data from Host to Camera) Pin 5 = TXD (serial data from Camera to Host) Pin 6 = GND Pin 7 = RESET IN (Reset to Camera) Pin 8 = CVBS OUT (available only in SD camera mode)
Cables
POWER INPUT: 7V TO 12V regulated, 8V recommended 6 Watts (FOR BOTH, CAMERA AND MODULE, CAMERA in HD mode) OPERATING CONDITIONS: Ambient Temperature (min/max): +5°C/+45°C = 41°F/113°F Humidity: 20%-70% STORAGE CONDITIONS: Temperature (min/max): 0°C/+50°C = 32°F/122°F Humidity: 20%-80% BOARD MECHANICAL: WIDTH = 44mm HEIGHT = 42mm THICKNESS = 1.59mm
From left to right: Micro coax cable, FFC and power/control/signal cable (all cables are supplied with module)
Board Mechanical TOP VIEW
(blue = PCB mounting holes, red = Panel cut-out holes location)
BOTTOM VIEW (J2 DETAIL)
42 mm 33 mm
11,75 mm 3 mm 5,845 mm
5 mm
SAFETY NOTE: The supplied FFC MUST be used with the HD-DVI Board and the FCB-H10.
6,5 mm 10 mm 34 mm 38,355 mm 44 mm
MaxxVision GmbH Sigmaringer Straße 121 70567 Stuttgart Tel.:0711/997-996-3 Fax:0711/997-996-50
[email protected] www.maxxvision.com
