Transcript
Model: HE1BIR-50M
____________________________________________________________________________________ HDMI Extender over One CAT5/6 with Bi-Directional IR Control up to 164ft (50m) The HE1BIR-50M uses only one cost effective CAT5/6 cable to extend your HDTV display up to 164ft (50m) at 1080p, with high quality uncompressed video, it delivers significant value to the entire home and commercial entertainment system. This HDMI extender only needs one power supply connected at the transmitter side and the receiver is powered through the CAT5/6 cable for a closer TV to wall installation. Easy to setup, EDID learning feature, Auto EQ, no level adjustments for optimal signal. ! ! ! ! ! ! ! ! ! !
Extends HDMI and IR over one CAT5/6 cable (CAT6 recommended for best results) Full HD 1080p@60Hz and 3D, Deep Color up to 36bit Max Data Rate – 6.75Gbps Supported Audio – LPCM, Dolby AC3, Dolby TrueHD, DTS-HD Bi-Directional IR, carrier frequency 30kHz to 60kHz HDMI and HDCP compliant Transmission range up to 164ft (50m) EDID learning and auto EQ Power needed only at the transmitter side if within 98ft (30m) Easy to install, Plug n Play, Small form factor
Installation View:
Note: In limited space applications, a special USB power cable can be used (Sold Separately) Model: 2USB135 will pull USB power from TV or source components instead of using included power supply.
Panel View:
____________________________________________________________________________________ 8805 Jones Rd. Ste C104, Houston Texas 77065 * 1-888-861-7351 * www.zuummedia.com
ZM 120813
Connection and Operation: Before installation, please make sure all devices you are connecting are turned off. 1) Connect your source to the transmitter extender using an HDMI cable 2) Connect your display to the receiver extender using an HDMI cable 3) Connect up to 164ft (50m) CAT5/6 cable from the transmitter extender to the receiver extender 4) Connect the 5VDC power supply or USB power cable to the transmitter and receiver extender 5) Turn on your source and display 6) No Picture? Test CAT5/6 cable, check the extender status lights or try EDID learning feature
Transmission Range: If connection is through a wall jack (not recommended), this could limit the full transmission distance between the transmitter and receiver extender. We recommended using a straight CAT5/6 cable with RJ45 connections on each end.
Shielded Cable: On most installations, we recommended using a shielded CAT5/6 cable with properly connected shielded RJ45 connectors. This will prevent video and audio loss due to EMI and other interference from switched lighting and ceiling fans.
Caution: 1. The wiring must be away from any equipment with electromagnetic signal, such as mobile phones, microwaves, radio communication equipment, fluorescent lighting, and high voltage power lines. 2. This device is not network compatible; do not connect via network to avoid damage.
IR Control Connections: - Step 1: When using IR remote at display side, plug IR receiver into receiver extender and move IR switch to Rx. On the source side plug IR blaster into transmitter extender and move IR switch to Tx. - Step 2: When using IR remote or control system at source side plug IR receiver into transmitter extender and move IR switch to Rx. On the display side plug IR blaster into receiver extender and move IR switch to Tx.
Status Lights: HE1BIR-50M-TX Blue - On (Power) RJ45 Green - On (Sending 5V power and HDMI data to receiver) RJ45 Yellow - On (No HDMI input or unsupported video format) HE1BIR-50M-RX Blue – On (Power by external power supply) RJ45 Green - On (5V power and HDMI data received from transmitter) RJ45 Yellow - On (No HDMI data or signal to weak)
EDID Default and Learning: EDID Default Dip switch 1 Off " 480i/720p/1080i/1080p Dip switch 2 Off " LPCM 2 Channel Audio Dip switch 2 On # LPCM 5.1 Channel Audio EDID Learning Dip switch 1 On # No picture or using a 3D display? Connect an HDMI cable from the display (HDMI Input1) to the transmitter extender. Turn on the display, select HDMI Input1, then plug in power to the transmitter extender and watch for the blue power light to start flashing. **Note** EDID learning is complete and saved after power is unplugged and re-plugged to transmitter.
____________________________________________________________________________________ 8805 Jones Rd. Ste C104, Houston Texas 77065 * 1-888-861-7351 * www.zuummedia.com
ZM 120813
RJ45 Define:
Package Contents: - HDMI Transmitter - HDMI Receiver - 2 x 5VDC 1Amp Power Supply - IR Receiver - IR Blaster - Mounting Screws - User Instructions
Specifications:
Model:
HE1BIR-50M-TX
Resolution
HE1BIR-50M-RX Up to 1080p@60Hz
Distance
164ft (50m) Max
Deep Color
24bit/36bit
IR Carrier Frequency
30kHz ~ 60kHz
IR Emit/Receive Angle
Tx: ± 30°, Rx: ± 55°
IR Receiver Distance
16ft (5m)
IR Connection
3.5mm Jack
HDMI Connector
Type A
Linking Interface
RJ45 x 1
Switch
2 Pin Dip Switch x 1, Slide Switch x 1
LED
Slide Switch x 1
Blue x 1, RJ45 Yellow/Green x 1
Power Supply
Two Regulated 5VDC 1A
Power Consumption Operation Temperature Dimensions - Inches Weight - lbs
420mA Max
180mA Max
Operation: 5 to 131°F, Storage: -4 to 185°F, Humidity: up to 95% 2.64”(w) x 4.02”(h) x 1.06”(d)
2.64”(w) x 3.58”(h) x 1.06”(d)
.33
.31
Do You Need Technical Support? ZuumMedia is proud to offer free technical support to ensure your product is operating correctly. If you are experiencing difficulties setting up this product, please call us for assistance 1-888-861-7351 or visit www.zuummedia.com for more information.
Here for You 24/7
____________________________________________________________________________________ 8805 Jones Rd. Ste C104, Houston Texas 77065 * 1-888-861-7351 * www.zuummedia.com
ZM 120813
