Preview only show first 10 pages with watermark. For full document please download

Here.

   EMBED


Share

Transcript

Semi-Industrial Temp mSATA SSD Product Data Sheet MS 801 SATAIII-6.0 Gb/s Semi-Industrial Temperature Grade 1 Page 1 of 16 Semi-industrial Temp XTM mSATA Solid State Drive– MS-801 Series 64 GB~256 GB 1. Features   Form Factor  mSATA solid State Drive (SSD)  50.95 mm x 30 mm x 1 mm  Totally compliant to standard SATA hard disk drive  52 pin (SATA power) mSATA connector Available Capacities   ECC    64GB~256 GB (MLC NAND Flash) Ultra-High ECC for 128 bit correction per 2KBytes High Performance  Up to 600 MB/s burst transfer rate in SATAIII, 6 Gb/s (NCQ Supported)  Sustained Read Performance: up to 520 MB/s  Sustained Write Performance: up to 420 MB/s  4KB Random Read/Write IOPS up to : 80000/62000 (peak value) Encryption and Protection  AES-128/256 Bit Supported  Advanced Power Management Supported  High Reliability  MTBF > 2,100,000 hours  Endurance: In normal operation condition, guarantees for 3 years product lifetime for half the SSD capacity sequential write per day.   Dynamic, static and active (initiative) balanced wear-leveling strategy  Intelligent Read Disturb Management  Intelligent Recycling for advanced free space management  Intelligent Data Retention Optimization  ECC Protection for Longest Data Retention and Drive Life  Power/Performance Balancing  Intelligent Bad-Block Management  S.M.A.R.T Supported  TRIM Command Supported Temperature Ranges  Semi-industrial Temperature Range: -20℃ ~+70℃ Ocean Manufacturing Ocean reserves the right to change products or specifications without notice. Revision: V03 2 2. Contents 1. Features.................................................................................................................................... 2 2. 3. Contents .................................................................................................................................. 3 Ordering Information .............................................................................................................. 4 3.1 Part Number Decoder ......................................................................................................... 5 4. General Description................................................................................................................ 6 4.1 Physical Description ................................................................................................... 6 4.2 4.3 4.4 4.5 4.6 4.7 5. 6. 7. 8. 9. System Performance .................................................................................................. 7 Environmental Specifications...................................................................................... 8 Reliability .................................................................................................................... 9 Physical Dimensions .................................................................................................. 9 CHS Parameter .......................................................................................................... 9 Drive Geometry .......................................................................................................... 9 Functional Block Diagram.................................................................................................... 10 Physical Dimension .............................................................................................................. 11 Electrical Interface ................................................................................................................ 12 7.1 Electrical Description ................................................................................................ 12 Feature Descriptions ............................................................................................................ 14 8.1 Wear Leveling........................................................................................................... 14 8.2 Bad Block Management ........................................................................................... 14 8.3 Endurance ................................................................................................................ 14 8.4 ECC .......................................................................................................................... 14 8.5 Standards Compliance ............................................................................................. 14 S.M.A.R.T Support.................................................................................................................. 15 9.1 Overview of S.M.A.R.T Support................................................................................ 15 9.2 S.M.A.R.T Command Set ......................................................................................... 15 9. Contact Information.................................................................................................................... 16 Ocean Manufacturing Ocean reserves the right to change products or specifications without notice. Revision: V03 3 3. Ordering Information The following Table 1 lists the part No. for Ocean MS-801 series SSDs. Table 1: Semi-industrial temperature product list Part Number Capacity Flash Type Form Factor OCXTMM-SATA64GTSSN 64 GB* MLC mSATA OCXTMM-SATA128GTSSN 128 GB* MLC mSATA OCXTMM-SATA256GTSSN 256 GB* MLC mSATA OCXTMM-SATA512GTSSN 512 GB* MLC mSATA * 1 GB=1,000,000,000 Bytes For latest ordering information, please consult Ocean’s sales representatives or check on our website: http://www.earthtron.com/ocean-manufacturing-memoright-solid-state-drive Ocean Manufacturing Ocean reserves the right to change products or specifications without notice. Revision: V03 4 3.1 Part Number Decoder OC FTMM 1 2 **** 3 G 4 T 5 S S* S 6 7 S OC: Ocean FTMM = MS801 S: Standard N: Normal, X:Custom Capacity 064G: 64 GB 128G: 128 GB 256G: 256 GB Temperature Option S: Semi-industrial (-20℃~70℃) 512G: 512GB T: mSATA Flash Type: MLC Ocean Manufacturing Ocean reserves the right to change products or specifications without notice. Revision: V03 5 4. General Description The Ocean ultra-speed and ultra-slim MS-801 series SSD provides you ultimate performance over traditional hard disk drive by achieving up to 520 MB/s/420 MB/s sequential read/write rate and up to 80000 IOPS (input/output operations per second) in CrystalDisk Benchmark test (Toshiba 256 GB). Moreover, the ultra-slim 1mm height of Ocean MS-801 series SSD makes it the best solution for ultrabook or any storage application that needs ultra-high performance with height limitation. For ultra-high security protection and reliability, Ocean MS-801 series SSD equips high speed Dual Core CPU for supporting 128/256-bit AES (Advanced Encryption Standard), thus it can fully meet business users’ strict requirement in ultra-low power consumption, ultra-high security and reliability. Moreover, Ocean’s QMS (Quality Management System) offers 100% traceability for every flash solution supporting in the process of production. Ocean MS-801 series SSD provides high-level data protection and reliability by using a combination of superior ECC algorithm up to 128 bytes and achieves longer SSD lifetime by integrating lower write amplification and Wear Leveling Factor. (WLF) By providing above-mentioned characteristics, Ocean MS-801 series SSD is the best solution to satisfy a variety of needs in industrial, military and consumer electronics storage applications no matter in performance, power consumption, form factor and cost considerations. Moreover, Ocean MS-801 series SSD also integrates many advanced technologies for enhancing its reliability such as intelligent Bad Block Management and Wear Leveling, intelligent Read Disturb Management, Power/Performance Balancing and intelligent Recycling for advanced free space management. 4.1 Physical Description The important component of Ocean MS-801 series SSD includes a Flash controller and NAND Flash memory modules. The controller works with a host system to allow data to be written to and read from the Flash memory modules through a (SATA) interface. The SSD is offered in a mSATA form factor with a SATA connector. Ocean Manufacturing Ocean reserves the right to change products or specifications without notice. Revision: V03 Page 6 of 16 4.2 System Performance Table 2: System Performance Table System Performance Max. Unit Data transfer Rate (SATA burst (6 Gb/s) 600 MB/s Sustained Sequential Read Rate 64 GB 520 MB/s Sustained Sequential Write Rate 64 GB 150 MB/s 4KB Random Read IOPS 64 GB 38000 IOPS 4KB Random Write IOPS 64 GB 24000 IOPS Sustained Sequential Read Rate 128 GB 520 MB/s Sustained Sequential Write Rate 128 GB 280 MB/s 4KB Random Read IOPS 128 GB 80000 IOPS 4KB Random Write IOPS 128 GB 62000 IOPS Sustained Sequential Read Rate 256 GB 520 MB/s Sustained Sequential Write Rate 256 GB 420 MB/s 4KB Random Read IOPS 256 GB 80000 IOPS 4KB Random Write IOPS 256 GB 62000 IOPS *1 GB=1,000,000,000 Bytes Ocean Manufacturing Ocean reserves the right to change products or specifications without notice. Revision: V03 Page 7 of 16 4.3 Environmental Specifications 4.3.1 Recommended Operating Conditions Table 3: Recommended Operating Conditions Parameter Value -20℃ to70℃ Semi-industrial Operating Temperature Temperature Gradient (℃ per hour max, non-condensing) 20℃ (operating) Temperature Gradient (℃ per hour max, non-condensing) 30℃ (non-operating) Power Supply Voltage Range 5V 4.3.2 Power Consumption (*) Table 4: Power Consumption Current/Power Consumption 3.3V Unit Continue Read Power (Average) 2 W Continue Write Power (Average) 2.1 W Idle Mode Power (Average) 0.5 W Standby Mode Power (Average) 0.5 W * All values are tested under room temperature 25℃ @ 3.3V. The power consumption may vary depends on different platform, OS, BIOS & test tools. 4.3.3 Recommended Storage Conditions Table 5: Recommended Storage Conditions Parameter Semi-industrial Storage Temperature Value -40℃ to 85℃ 4.3.4 Shock, Vibration and Humidity Table 6: Shock, Vibration and Humidity Parameter Value Humidity (non-condensing) 5%~95% (Operating) Relative Humidity Gradient 30% per hour max Vibration 10G (Peak, 10~2000Hz) Shock (Operating) 1000G Shock (Non-Operating) 1500G Ocean Manufacturing Ocean reserves the right to change products or specifications without notice. Revision: V03 Page 8 of 16 4.4 Reliability Table 7: Reliability Parameter Value > 2,100,000 hours (Calculation mode: Mean Time Between Failures (MTBF) Telcordia SR-332 Issue 1 Method 1, Case 1) Data Retention 4.5 10 years Physical Dimensions Physical Dimensions Unit Length 50.95 mm Width 30 mm Thickness 1 mm 4.6 CHS Parameter Unformatted Capacity Guaranteed Sectors Bytes per Sector 64 GB* 125000064 512 128 GB* 250000000 512 256 GB* 500000256 512 512 GB* 100000025 6 512 *1GB=1,000,000,000 Bytes 4.7 Drive Geometry Capacity Default Cylinders Default Heads Default Sectors 64 GB* 124008 16 63 128 GB* 248016 16 63 256 GB* 496032 16 63 512GB* 992064 16 63 Page 9 of 16 Ocean Manufacturing Ocean reserves the right to change products or specifications without notice. Revision: V03 5. Functional Block Diagram Figure 1: Functional Block Diagram MS-801 Series 2.5" SATA III Connector SATA Host up to 6 Gbps CPU0 CPU1 Sequencer RAID AES DMAC SPM NAND ECC NAND UART I2C SPI JTAG PWR MGMT GPIO TIMER DDR DDR2/3-800 Ocean Manufacturing Ocean reserves the right to change products or specifications without notice. Revision: V03 Page 10 of 16 6. Physical Dimension Physical Dimensions Unit Length 50.95 mm Width 30 mm Thickness 1 mm Ocean Manufacturing Ocean reserves the right to change products or specifications without notice. Revision: V03 Page 11 of 16 7. Electrical Interface 7.1 Electrical Description The drive uses the industry-standard Serial ATA interface that supports 16-bit data transfers. It supports programmed input/output (PIO) modes 0–4; Ultra DMA modes 0–6. The drive also supports the use of the IORDY signal to provide reliable high-speed data transfers. For detailed information about the Serial ATA interface, refer to the draft of AT Attachment with Packet Interface Extension (ATA/ATAPI-7), NCITS T13 1410D, subsequently referred to as the Draft ATA-7 Standard. For detailed information about the Serial ATA interface, refer to the draft of AT Attachment with Packet Interface Extension (ATA/ATAPI-7), NCITS T13 1410D, subsequently referred to as the Draft ATA-7 Standard. The connector on Ocean mSATA MS-801 series SSD is divided into a signal Segment and a power Segment. The following tables summarize the signals on the SATA interface connector. For a detailed description of these signals, refer to the Draft ATA-7 Standard. Please see following Figure and table for signal and power pin assignment. Figure 2 mSATA pin Ocean Manufacturing Ocean reserves the right to change products or specifications without notice. Revision: V03 Page 12 of 16 Table 8 Pin Assignment and description for Signal and Power pins Pin No. Pin Name Pin No. Pin Name Pin No. Pin Name Pin No. Pin Name 1 NC 14 NC 27 GND 40 GND 2 +3.3V 15 GND 28 NC 41 +3.3V 3 NC 16 NC 29 GND 42 NC 4 GND 17 NC 30 NC 43 GND 5 NC 18 GND 31 SATA_ RX- 44 NC 6 NC 19 NC 32 NC 45 NC 7 NC 20 NC 33 SATA_ RX+ 46 NC 8 NC 21 GND 34 GND 47 NC 9 GND 22 NC 35 GND 48 NC 10 NC 23 SATA_TX + 36 NC 49 NC 11 NC 24 +3.3V 37 GND 50 GND 12 NC 25 SATA_TX- 38 NC 51 GND 13 NC 26 GND 39 +3.3V 52 +3.3V Ocean Manufacturing Ocean reserves the right to change products or specifications without notice. Revision: V03 Page 13 of 16 8. Feature Descriptions 8.1 Wear Leveling For extending SSD’s life time, a sophisticated wear leveling technology is important. Ocean MS801 series provides dynamic, static (initiative) balanced wear leveling strategy. The dynamic wear leveling algorithm ensures that erase/write cycles can be evenly distributed across all flash memory block locations to prevent excessive writes to the same physical flash memory location. 8.2 Bad Block Management Ocean MS-801 series SSD provides bad block management function with a certain number of reserved blocks. When a user data block fails, a reserved block will replace the failed block. The replacement of bad block is transparent to user. 8.3 Endurance In normal operation condition, guarantees for 3 years product lifetime for half the SSD capacity sequential write per day. 8.4 ECC Ocean MS-801 series SSD provides ultra-high ECC for 128 bit correction per 2KBytes. 8.5 Standards Compliance Ocean MS-801 series SSD complies with following standards. FCC CE RoHS Ocean Manufacturing Ocean reserves the right to change products or specifications without notice. Revision: V03 Page 14 of 16 9. S.M.A.R.T Support 9.1 Overview of S.M.A.R.T Support Data storage drives capture a variety of information during operation that may be used to analyze drive “health.” Drive manufacturers have adopted S.M.A.R.T. (Self-Monitoring, Analysis, and Reporting Technology) to help warn system software, a system administrator, or a user of impending drive failure, while time remains to take preventive action. The technical documentation for S.M.A.R.T. is captured in the AT Attachment (ATA) standard. The standard defines the protocols for reporting errors and for invoking self-tests to collect and analyze data on demand. The ATA specification is flexible and provides for individual manufacturers to define their own unique vendor specific information. This section describes the baseline S.M.A.R.T. Commands and Attributes supported by the MS-801 series processor. The information herein should be used in conjunction with the ATA standard and related documents, which may serve as references for topics and details not addressed here. Further, it is recommended to consult the list of public S.M.A.R.T. attributes. 9.2 S.M.A.R.T Command Set Table 9 S.M.A.R.T command Set Index ID(Dec) ID(Hex) Attribute Name 2 5 05h Retired Block Count 3 9 09h Power On Hours Count 4 12 0Ch Power Cycle Count 7 173 ADh Average Erase Count 8 174 AEh Unexpected Power Loss Count 10 181 B5h Non-4K Aligned Access 11 183 B7h SATA Interface Downshift 13 188 BCh Command Timeout 14 189 BDh Factory Bad Block Count 15 194 C2h Temperature 18 199 C7h Ultra DMA CRC Error Rate 29 206 CEh Write Error Rate 20 231 E7h SSD Life Left 23 247 F7h Host Program Page Count 25 255 FFh Power on minutes information Ocean Manufacturing Ocean reserves the right to change products or specifications without notice. Revision: V03 Page 15 of 16 9. Contact Information EarthTron 210 West Rd Unit 6 General Support 603-433-2007 Portsmouth, NH 03801 Fax 603-433-9376 USA E-mail [email protected] DISCLAIMER OF LIABILITY Ocean Manufacturing reserves the right to make changes to specifications and product descriptions such as but not limited to numbers, parameters and other technical information contained herein without notice. Please contact Ocean Manufacturing to obtain the latest specifications. Ocean Manufacturing grants no warranty with respect to this datasheet, explicit or implied, and is not liable for direct or indirect damages. Some states do not grant the exclusion of incidental damages and as such this statement may not be valid in such states. The provisions of the datasheet do not convey to the purchaser of the device any license under any patent right or other intellectual property right of Ocean Manufacturing or others COPYRIGHT NOTICE Copyright © 2013 by Ocean Manufacturing All rights reserved. Information contained in this document, including but not limited to any instructions, descriptions and product specifications, is considered proprietary and confidential to Ocean Manufacturing and shall not be modified, used, copied, reproduced or disclosed in whole or in part, in any form or by any means, electronic or mechanical, for any purpose, without the written consent of Ocean Manufacturing Ocean Manufacturing Ocean reserves the right to change products or specifications without notice. Revision: V03 Page 16 of 16