Transcript
HydraConnect LLC
HEXT-21b HDBaseT HDMI Extender
www.hydraconnect.com
( 720-583-4364
HydraConnect LLC
Table of Contents Safety Information.........................................................................1 Introduction...................................................................................2 Product Features............................................................................2 Module Connections....................................................................3 Transmitter Module Connections........................................3 Receiver Module Connections..............................................3 Product Installation.......................................................................4 Product Operation........................................................................6 Product Maintenance....................................................................6 Cable Pinouts.................................................................................7 IR Cables..................................................................................7 Link Cable................................................................................7 HDMI Cable............................................................................7 Technical Specifications................................................................9 Warranty.........................................................................................10 Limited Warranty....................................................................10 Customer Remedies................................................................10 No Other Warranties..............................................................10 No Liability For Damages......................................................10
Rev 1.1 www.hydraconnect.com
( 720-583-4364
HydraConnect LLC
Safety Information Please read and understand all instructions in this manual before operating this equipment. ¾¾ Keep these instructions in a safe, accessible place for future reference. ¾¾ Pay attention to all warnings, and follow all instructions. If the equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impaired. ¾¾ Do not use this equipment near water, and unplug the product before cleaning and clean only with a dry cloth. ¾¾ Do not install near any heat sources such as heat registers, stoves, or other equipment that produce heat. ¾¾ Explanation of graphical symbols: Exclamation point symbol: the exclamation point within an equilateral triangle symbol is intended to alert the user to the presence of important operating and maintenance instructions in the literature accompanying the product.
¾¾ WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE AND OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHOULD NOT BE PLACED ON THIS EQUIPMENT. ¾¾ Do not block the air ventilation openings. Only mount the equipment per HydraConnect’s instructions. ¾¾ Ensure that all IR connections are made BEFORE power is applied to either module. Failure to observe this requirement may result in damage to the modules that will not be covered under warranty. ¾¾ NOTE, This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures: •
Reorient or relocate the receiving antenna
•
Increase the separation between the equipment and the receiver
•
Connect the equipment into a outlet on a circuit different from that to which the receiver is connected
•
Consult the dealer or an experienced radio/TV technician for help
www.hydraconnect.com
Page 1
( 720-583-4364
HydraConnect LLC
Introduction The HEXT-21 is a second generation HDMI extender. It utilizes HDBaseT technology to extend uncompressed HDMI signals up to 330 feet (100 meters). The HEXT-21 consists of a transmitter, a receiver, a 24 volt power supply, and mounting brackets. The transmitter and receiver are interconnected using a single CAT5e/6 cable.
Product Features •
Fully compatible with HDBaseT specifications for HDMI Extenders
•
Provides 330 feet (100 meter) distance signal link with full uncompressed HD 1080p video
•
Supports HDMI v1.4a with CEC and EDID pass through and Deep Color
•
Fully compliant with HDCP
•
Fully 3D Compatible (all 7 formats), including the most popular e.g., Frame Packing, Side-by-Side, Top-to-Bottom
•
Supports all latest Audio formats such as Dolby True HD, DTS-master, etc.
•
Supports bi-directional IR pass through of all frequency band hardware - 20K – 80KHz, all protocols
•
Supports 10.2Gbps HD source signal (4Kx2K)
•
Operates over standard CAT5e/6 UTP/STP link cable solid
•
Supports standard CAT6 FTP solid link cable (recommended)
•
Small Size Transmitter - 1” X 2” X 3 “ (2.4cm X 4.8cm X 7.2cm)
•
Small Size Receiver - 1” X 3” X 4” (2.4cm X 7.2cm X 10.1cm)
•
Single 24VDC power supply at the transmitter only
•
Extensive side-mounted diagnostic LEDs
•
Fully compliant with IEEE802.1Q, IEEE802.3, IEEE802.3u & IEEE802.3x standards
•
Green power features - low operating power of ~8 W, auto power down to ~2W
www.hydraconnect.com
Page 2
( 720-583-4364
HydraConnect LLC
Module Connections Transmitter Module Connections
1 3
2
5
4
1. IRDA Out - Infrared 3.5mm socket for plugging in the IR flasher 2. +24VDC IN - Connect to supplied power supply 3. CAT5e/6 OUT - Plug in a Cat-5e/6 cable that needs to be linked to the Receiver module. 4. HDMI IN - Connect to a HDMI source with a HDMI male-male cable 5. IRDA In- Infrared 3.5mm socket for plugging in the IR receiver
Receiver Module Connections
1
2
3
4
1. IRDA Out - Infrared 3.5mm socket for plugging in the IR flasher 2. CAT5e/6 IN - Plug in a Cat-5e/6 cable that needs to be linked to the Transmitter module. 3. HDMI OUT - Connect to a HDMI Display with a HDMI male-male cable 4. IRDA In - Infrared 3.5mm socket for plugging in the IR receiver www.hydraconnect.com
Page 3
( 720-583-4364
HydraConnect LLC
Product Installation 1. Identify a location for the transmitter module that is within 6 feet (2 meters) of the source. To use the supplied mounting bracket, follow these steps: a. Determine on which side of the module to attach the mounting bracket b. Remove the 2 screws from that side of the module and discard c. Attach the supplied bracket using the two supplied screws per the picture below:
d. Using the appropriate screws, mount the module through the mounting bracket holes 2. Connect a High Speed HDMI Male-to-Male cable between the transmitter module and the source. 3. If used, connect an IR Flasher or Receiver to the designated connectors. NOTE THAT INSTALLING AN IR FLASHER OR RECEIVER INTO THE WRONG CONNECTOR MAY DAMAGE THE MODULE WHICH WILL NOT BE REPAIRED UNDER WARRANTY. 4. If an automation system IR passthrough is needed, connect a 3.5mm mono connector cable between the output of the automation system and the IR input on the transmitter. Connect the IR flasher to the IR output on the receiver. NOTE: Unlike previous extenders, no adapter cable is required between the automation system and the transmitter. 5. Connect the properly terminated end of a CAT5e/6 cable to the designated connector (see Link Cable specifications for cable requirements). NOTE: DO NOT CONNECT THE CAT5e/6 TO ANY DEVICE OTHER THAN THE SUPPLIED TRANSMITTER AND RECEIVER, PARTICULARLY NOT TO ANY NETWORK DEVICE! THE VOLTAGE DELIVERED FROM THE TRANSMITTER WILL LIKELY DAMAGE SUCH DEVICES.
www.hydraconnect.com
Page 4
( 720-583-4364
HydraConnect LLC 6. Similarly, locate the receiver module within 6 feet (2 meters) of the display. The receiver has permanently attached mounting brackets. Mount the receiver so that the status LEDs which are mounted on the side of the unit are visible when you look behind the display.
IT IS IMPERATIVE THAT THE RECEIVER BE MOUNTED HORIZONTALLY ON A VERTICAL WALL FOR PROPER OPERATION AS SHOWN BELOW:
7. Connect a High Speed HDMI Male-to-Male cable between the receiver module and the display. 8. If used, connect an IR Flasher or Receiver to the designated connectors. NOTE THAT INSTALLING AN IR FLASHER OR RECEIVER INTO THE WRONG CONNECTOR MAY DAMAGE THE MODULE WHICH WILL NOT BE REPAIRED UNDER WARRANTY. 9. Plug the output power cable from the supplied 24VDC power supply into the transmitter module. Plug the power supply into an electrical outlet. 10. Both modules should power up - the Power and Link LEDs should light on both modules
www.hydraconnect.com
Page 5
( 720-583-4364
HydraConnect LLC
Product Operation
The transmitter and receiver modules have no user adjustments or controls - they are fully self configuring and automatically adjust themselves to the environment. Both modules have three LEDs which indicate the module’s status. They are interpreted as follows:
Transmitter LEDs
Receiver LEDs
Power LED: ON: Indicates that proper power is available OFF: On the transmitter, power is not available from the power supply; on the receiver, no power is available over the link cable HDMI LED: ON: Data is being received and is HDCP protected BLINK: Data is being received and is not HDCP protected OFF: No data is being received Link LED: ON: Link connection is good and unit is powered up BLINK: Link connection is good and unit is powered down FLICKER: Connection cannot be established OFF: No communication between transmitter and receiver
Product Maintenance The transmitter and receiver modules require no maintenance. However, the units should be kept clear of liquids and the ventilation slots should be kept clear of dust and other obstructions.
www.hydraconnect.com
Page 6
( 720-583-4364
HydraConnect LLC
Cable Pinouts IR Cables The IR receiver has the following pinout:
The IR transmitter has the following pinout:
www.hydraconnect.com
Page 7
( 720-583-4364
HydraConnect LLC
Link Cable
The link cable has the following recommended pinout - note that both ends of the cable are identical:
Recommended Link Cable must meet TIA/EIA‐568‐B specifications. Such cable would be CAT5e UTP/STP, CAT‐6 FTP cable in solid core types (350MHz). CAT‐6 cable is preferred for best results.
HDMI Cable The HDMI cable has the following pinout:
Pin 1 TMDS Data2+ Pin 2 TMDS Data2 Shield Pin 3 TMDS Data2Pin 4 TMDS Data1+ Pin 5 TMDS Data1 ShieldPin 6 TMDS Data1Pin 7 TMDS Data0+ Pin 8 TMDS Data0 Shield Pin 9 TMDS Data0Pin 10 TMDS Clock+
www.hydraconnect.com
Pin 11 TMDS Clock Shield Pin 12 TMDS ClockPin 13 CEC Pin 14 Reserved Pin 15 SCL Pin 16 SDA Pin 17 DDC/CEC Ground Pin 18 +5 V Power Pin 19 Hot Plug Detect
Page 8
( 720-583-4364
HydraConnect LLC
Technical Specifications ӹӹ HDMI version 1.4a compliant ӹӹ Supports 3D pass through, deep color, and all available audio formats ӹӹ Fully HDCP compliant ӹӹ Data rate to 10.2 Gbps ӹӹ CEC and EDID Pass through ӹӹ Bi-directional IR pass through »» Signal distance from extender output- up to 40 feet (15 meters) »» Frequency support - 20KHz to 80KHz »» Protocol support - any protocol ӹӹ Recommended link cable is CAT5e UTP/STP, CAT‐6 FTP cable in solid core ӹӹ Power source - 24VDC .36A 8.6W 100-240V AC input power supply ӹӹ Power consumption - ~8 watts operating, ~2 watts standby ӹӹ Approvals: CE/UL and FCC - RoHS compliant
www.hydraconnect.com
Page 9
( 720-583-4364
HydraConnect LLC
Warranty Limited Warranty HydraConnect LLC warrants that (a) its products will perform substantially in accordance with the accompanying written materials for a period of 5 years from the date of receipt and (b) that the product will be free from defects in materials and workmanship under normal use and service for a period of 5 years. In the event applicable law imposes any implied warranties, the implied warranty period is limited to 5 years from the date of receipt. Some jurisdictions do not allow such limitations on duration of an implied warranty, so the above limitation may not apply to customers that fall within those areas.
Customer Remedies HydraConnect LLC and its suppliers’ entire liability and Customer’s exclusive remedy shall be, at HydraConnect LLC’s decision, either return of the price paid for the product, repair, or replacement of the product that does not meet this Limited Warranty and which is returned to HydraConnect LLC with a copy of the Customer’s receipt. This Limited Warranty is void if failure of the product has resulted from accident, abuse, misapplication, or natural occurrence. In example but not limited to: power surges (electrical storms, local power outage), dropping the product (or items on the product), contact with fluids, and physical misconduct. Any replacement product will be warranted for the remainder of the original warranty period.
No Other Warranties To the maximum extent permitted by applicable law, HydraConnect LLC and its suppliers disclaim all other warranties, either expressed or implied, including, but not limited to, implied warranties of merchantability and fitness for a particular purpose, with regard to the product and any related written materials. This Limited Warranty gives customer specific legal rights. Customers may have other rights depending on the jurisdiction.
No Liability For Damages To the maximum extent permitted by applicable law, in no event shall HydraConnect LLC or its suppliers be liable for any damages arising out of the use of or inability to use this product, even if HydraConnect LLC has been advised of the possibility of such damages. Such damages include but are not limited to: special, incidental, consequential, or indirect damages for personal injury, loss of business profits, business interruption, loss of business information, or any other pecuniary loss. HydraConnect LLC’ and its suppliers’ entire liability under any provision of this agreement shall be limited to the amount actually paid by you for the product. Some Jurisdictions do not allow the exclusion or limitation of liability for consequential or incidental damage. The above limitations may not apply to you in such jurisdictional cases.
www.hydraconnect.com
Page 10
( 720-583-4364
