Transcript
Before you start
4 Chassis Ground CAUTION
Many new and factory radios require a reset code when disconnected from battery power. This is an anti-theft feature. Before unplugging power, you must determine if your radio/source unit requires a reset code. Check the operation manual for your vehicle or contact the dealer.
The chassis ground connection is critical to the performance of the amplifier. Choose a location that is close to the amplifier. Completely scrape away the paint and use a nut and bolt if possible. DO NOT USE AN EXISTING FACTORY BOLT!
Model
Fuse Size
Cable Size
BE35-500.4
2x25A ATC
4ga
BE35 800.4
2x35A ATC
4ga
BE35 1200.1D
1 x 80A Maxi
4ga
BE35 1700.1D
2 x 70A Maxi
2ga
Be sure to use the proper fuse size for each model. Some models require an external fuse.
BE35 2100.1D External 200A
0ga
BE35 2500.1D External 250A
0ga
External 100A
2ga
BE35 5000.5
1 Disconnect
negative battery terminal
Place terminal in a secure position so that it won’t accidentally contact the negative battery post
2 Run Cables
3 Mount Amplifier Choose a mounting location that will provide adequate air ventilation. Mount the amplifier to a secure surface. Do not mount the amplifier upside down.
SPEAKER
OUTPUT
OUTPUT
Stereo
SPEAKER
OUTPUT
Bridged BRIDGED
BRIDGED
BRIDGED
CH 2
CH 1
RIGHT
LEFT
BRIDGED RIGHT
CH 4
CH 3
5 Negative Power BRIDGED
BRIDGED
LEFT
Attach the chassis ground cable to the amplifier negative terminal. It is important to make sure this connection is very tight.
RIGHT SPEAKER
SPEAKER
CH 4 SPEAKER
CH 3 OUTPUT
OUTPUT
SPEAKER
OUTPUT
BRIDGED
6
Monoblock
Remote Turn-on Connection
Attach the remote turn on wire to the amplifier remote output of the source unit.
LEFT
SPEAKER
OUTPUT
LEFT
CH 4
CH 3
BRIDGED
BRIDGED
BRIDGED RIGHT
OUTPUT SPEAKER
SPEAKER OUTPUT
SPEAKER
SPEAKER OUTPUT
OUTPUT
SPEAKER
LEFT
RIGHT
CH 1
OUTPUT
OUTPUT SPEAKER
SPEAKER
SPEAKER OUTPUT
SPEAKER OUTPUT
CH 2
Monoblock OUTPUT
OUTPUT
BRIDGED LEFTSPEAKER
SPEAKER SPEAKER
multiple woofers
RIGHT OUTPUT
OUTPUTOUTPUT
CH 3
CH 4
Positive Power Connection
Attach the main power cable to the amplifier +12V. The cable must run directly to the battery and be properly fused and be very tight.
RIGHT
11 Positive Battery
OUTPUT
SPEAKER
SPEAKER OUTPUT
SPEAKER
OUTPUT
OUTPUT SPEAKER
OUTPUT
SPEAKER
OUTPUT
Be prepared to disarm your vehicle’s alarm and to enter your radio / source unit code.
BRIDGED CH 4
CH 3
OUTPUT
Connect the power cable to the positive battery terminal. The power cable must be fused within 18 inches of the battery terminal.
Connection
9 Level Control
SPEAKER
Connection
8 Signal Input Connect the RCA cables to the INPUT connectors. The OUTPUT can be used to provide input for a second amplifier.
OUTPUT
CH 4
CH 3
CH 2
CH 1
SPEAKER
BRIDGED
BRIDGED
BRIDGED LEFT
12 Re-connect SPEAKER
Negative Battery Terminal
OUTPUT
Turn the LEVEL control completelyINPUT counter-clockwise to minimum. LEVEL
INPUT LEVEL
MODE XOVER SUBSONIC SUBSONIC Re-connect the negative
battery terminal making sure it is securely tightened. FULL
9V
0.2V
PHASE
6V
0.2V
LPF
15
35Hz
LPF
10
40Hz
LPF
LP
HP
XOVER
MONO STEREO
MODE
SPEAKER
OUTPUT
BRIDGED
7
OUTPUT
BRIDGED
single woofer
SPEAKER
OUTPUT SPEAKER
BRIDGED
CH 4
CH 2
CH 1
RIGHT
SPEAKER OUTPUT
SPEAKER
SPEAKER
OUTPUT
CH 3
SPEAKER
Properly route power, speaker and RCA cables through the vehicle.
CH 4
Bare metal
BRIDGED
Installation
BRIDGED
CH 3
Connect the speaker cables to the speaker output connectors. SPEAKER OUTPUT Follow the diagram below that best fits your speaker configuration.
SPEAKER
Connection
It is critical to use the proper power and ground cable. Select the size listed here for your amplifier model. Always use high quality copper cable. Visit our website for multi amp system cable recommendations.
Connections
RIGHT
LEFT
Power cable size and fusing
10 Speaker
BRIDGED LEFT
SPEAKER
BASS EQ
Input Mode 0
10dB
B Xover Mode
35
250Hz
High pass Adjustment
250Hz
40
300Hz
0
9V
9dB 0.2V
60
FULL
1.3KHz 60 1.2KHz 6V 9V 0.2V 0.2V 156V 35Hz 0.2V 10 15 40Hz35Hz
The XOVER Mode switch sets the type of crossover 4 channelLPFLPF PHASE that will LPFbe active. LPF PHASE LPF models will have two switches, one for each set of channels. 180
350
250Hz 180
30 35 250Hz 250Hz 40 30300Hz 250Hz
D Low pass Adjustment
MONO STEREO FULL LPF HPF
E Bass Boost
300Hz
LPF4CH 1.2KHz
6V
0.2V
LPF LPF
LPF
60Hz1
LPF
FULL LPFH PF
SPEAKER
60Hz1
.2KHz
30
10dB
0
60
9dB
0
LPF
250Hz
12dB
SPEAKER
40
300Hz
40Hz
60
60
1.2KHz
250Hz
HP
60Hz1
.2KHz
This is a critical step to insure your amplifier INPUT is properly adjusted to match the signal LEVEL output level of your source unit.
INPUT LEVEL
9V
0.2V
6V
1.5Hz
OUTPUT
XOVER
SPEAKER CH 3
BRIDGED
BASS EQ SPEAKERHPF
LEVEL BRIDGED
LEFT
MODE
SUB SONIC
SPEAKER
OUTPUT
CHLEFT 1
RIGHT
6V
0.2V
SPEAKER
OUTPUT CH 4
1.
If possible, with the source unit off, confirm that the primary volume control is PHASE LPF turned down (counter clockwise).
2.
Turn on the source unit (CD, or MP3 player). Re-confirm that the volume is turned down. Make sure the source unit controls; balance, fader, bass35and250Hz 0 180 treble are all set to center or “0” adjustment. Make sure that the green LED on the end of the amplifier is illuminated. BASS CD EQ is preferred. BASS EQ Play a clean musical selection of which you are very familiar.
15
35Hz
LPF
30
250Hz
HPF
Do not use radio signals for level setting. Hit play and start turning the volume of the source unit up. 0
10dB
0
9dB
4.
Stop increasing the source unit volume when you reach 3/4 (about 75%) or until you hear speakers begin to slightly start producing distortion.
5.
Increase the amplifier level (clockwise) until distortion is heard, then back the level down (counter clockwise) until the distortion is eliminated. Small adjustments may need to be made to balance the levels of multiple amplifiers.
60
1.3KHz
OUTPUT
10
OUTPUT
RIGHT
SPEAKER
Quick Start Installation Guide
OUTPUT
0
12dB
BRIDGED BRIDGED
60
SPEAKER
OUTPUT
SPEAKER
OUTPUT
SPEAKER
OUTPUT
LPF
OUTPUT
BRIDGED CH 2 RIGHT
1.2KHz
30
BRIDGED
BRIDGED LEFT
250Hz
RIGHT
LEFT CH 4
CH 3
RIGHT
CHANNEL 3/4
SPEAKER
OUTPUT
SPEAKER SPEAKER
OUTPUT
OUTPUT OUTPUT SPEAKER
SPEAKER OUTPUT
OUTPUT
SPEAKER SPEAKER
OUTPUT OUTPUT
SPEAKER
MODE
OUTPUT
LEVEL
SPEAKER
BASS EQ
LEVEL 4CH
6V
SPEAKER BRIDGED
BRIDGED HPF
CH 3 LEFT
CH 4 RIGHT
2CH
0.2V
6V
OUTPUT
SPEAKER
0.2V
0 OUTPUT
12dB
60
CHANNEL SPEAKER3/4 SPEAKER
LPF
SPEAKER
SPEAKER
OUTPUT
SPEAKER
OUTPUT
1.2KHz
30
10
40Hz
CH 2
250Hz
OUTPUT OUTPUT
SPEAKER
OUTPUT
LPF
40
XOVER
OUTPUT
SPEAKER
OUTPUT
SPEAKER
OUTPUT
BE35 500.4 BE35 2100.1D BE35 800.4 BE35 2500.1D BE35 1200.1D BE35 5000.5 BE35 1700.1D SPEAKER
300Hz CH 3
MODE
OUTPUT
BRIDGED CH 1
OUTPUT
BRIDGED
OUTPUT
SPEAKER
LEFT
LOW PASS
X-OVER
SUBSONIC
SUBSONIC SUBSONIC
0.2V
OUTPUT OUTPUT
CH 4
CH 3
CH 4
SPEAKER
OUTPUT
BRIDGED
RIGHT HPF
MONO STEREO
X-OVER
12dB Mono 1/2
MONO STEREO
OUTPUT
STEREO FULL LPF HPF 15Hz MONO HPF HPF 50Hz LPF FULL 300Hz LPF FULL 35Hz 35Hz2
0
MODE
SPEAKER SPEAKER
OUTPUT
MODE
0.2V
1.2KHz
OUTPUT CHANNEL
XOVER
LP
6V
LOW PASS
MODE
1.3KHz
SPEAKER
OUTPUT
OUTPUT
SPEAKER
BRIDGED
HPF LPF FULL
SPEAKER
XOVER
40Hz
CH 4
CH 3
X-OVER
HPF LPF FULL
CHANNEL 1/2
OUTPUT
30Hz
LEVEL Mono 4ch - Mixed
10
LPF SPEAKER
SPEAKER SPEAKER
.2KHz
HPF OUTPUT
30Hz BRIDGED 1.5Hz
X-OVER
FULL
30Hz 1.5Hz 40Hz 300Hz 180 35 250Hz
OUTPUT OUTPUT
BRIDGED CH 2
SPEAKER
THIS IS NOT A VOLUME CONTROL!
3.
1.5Hz
EQ 4CHBASS2CH
CH 4 1.2KHz 60
CH 3
Level Setting
.5KHz
MODE
15BRIDGED35Hz
FULL LPFBRIDGED HPF
G
10Hz1
MONO STEREO
MODE
2CH HPF
30 CH 3250Hz
30
Remote Level Control
30Hz
XOVER LEFT
2CH 3CH 4CH
OUTPUT
SPEAKER
FULL LPFH PF
.5KHz
The Bass EQ control will increase the power 2CH 3CH 4CH HPF HPF BASS EQ BASS EQ output at 45Hz for more pronounced bass. Exercise caution when using this control. BRIDGED LPF BRIDGED CHHPF BASS EQ 2 CH 1 LEFT RIGHT Increase the level in small amounts until distortion is noticed, then back off a little. Some models include a bass remote. Avoid adjusting the bass remote while operating vehicle.
BRIDGED CH 1
RIGHT HPF
LPF
XOVER SPEAKER
SUBSONIC SUBSONIC
OUTPUT
0
F
10Hz1
MODE
60
LPF PHASE
0
MODE
HPF
HPF INPUT LEVEL
RIGHT
SPEAKER
LEFT
FULL LPFH PF
.5KHz
HPF
FULL LPF HPF
9VBRIDGED0.2V
The LPF(low pass filter) control will limit output above the selected frequency. This is used to allow a smooth transition to the higher frequency speakers.
MONO STEREO 10Hz1
MODE XOVER
TheBASS HPF(high limitHPF the HPF will EQ pass BASSfilter) EQEQ control HPF BASS EQ This output below the BASS selected frequency. INPUT LEVEL is typically used to protect midrange and hi frequency speakers from damage and to 60 1.3KHz 60 1.2KHz 10dB 0 9dB from allow0 a smooth transition 60 1.3KHz 0 10dB 0 a subwoofer. 9dB LEFT
MONO FULL STEREO HP LP
XOVER LPF
40
SPEAKER SPEAKER
SPEAKER
BRIDGED XOVER
HPF
HP
OUTPUT OUTPUT
4ch - Full Range
MODE
MODE XOVER
10 LP 40Hz
SPEAKER SPEAKER
OUTPUT OUTPUT
Common System Setup
MONO STEREO
FULL LPF HPF
The MODE switch will sum or combine the right MODE and left channel signals 2CH position to XOVER INPUT INPUT INPUT in the HPF HPFINPUT BASS EQ improve bass performance when bridging the SUBSONIC SUBSONIC SUBSONIC LEVEL LEVEL LEVEL SUBSONIC LEVEL amplifier to mono. Use the 4CH mode when driving four full range speakers. 4CH 2CH
0
C
30
SPEAKER SPEAKER
CH 3/4
A
180
OUTPUT
CH 3/4
0
SPEAKER
CH 3/4
Setup
MODE
XOVER
LPF
CH 1/2
LPF
CH 3/4
LPF
CH 1/2
PHASE
CH 4
OUTPUT
The information within this document is intended to offer some SPEAKER basic guidelines OUTPUT MONO STEREO FULL HP contained for a few LP of the most common installations. More complex audio systems should be installed by a competent professional. Additional installation information available at www.maxxsonics.com MODE XOVER
40Hz
LPF
WARRANTY Maxxsonics USA Inc. warrants this product, to the original consumer purchaser, to be free from MONO workmanship STEREO LPF HPF and defectsFULL in material for a period of one (1) year from the date of purchase. 40 300Hz Maxxsonics USA Inc. will, at it’s discretion, repair or replace defective products during the warranty period. Components thatMODE prove to be defective in materials and workmanship under proper installation HPFand use must be returned to the original authorized Maxxsonics USA Inc. retailer from where it was purchased. A photocopy of the original receipt must accompany the product being returned. The costs associated with removal, re-installation and freight are not the responsibility of Maxxsonics 4CH is limited 2CH USA Inc. This warranty to defective parts and specifically excludes any incidental or 60 1.2KHz consequential damages connected therewith. To view the full warranty, please visit the website. Hifonics products are designed and engineered in the USA by 847-540-7700 www.maxxsonics.com
HF BE35 2015 QSG 01 - rev1
Congratulations on your choice of a Hifonics amplifier. This “Quick Start Installation” guide is meant to help you “hook up” and play music. For more detailed information, on system setting, speaker and subwoofer configuration and full specifications by model visit the website, http://hifonics.com/manuals.html
