Transcript
High Power VCSEL Pumped Solid State Laser Product # PR-LSIG-12-W1064 • VCSEL technology • DPSS pass Q-switch • High temperature operation without active cooling. • Compact rugged design • High shock/vibration resistance • High pulse energy and power density OPTICAL & ELECTRICAL CHARACTERISTICS PARAMETER
CONDITIONS
MIN
TYP
MAX
UNIT
Pulse energy
200A, 50C ambient
10
12.0
20
mJ
Pulse duration
200A, 50C ambient
4
4.5
5
nS
Repition rate
200A, 50C ambient
--
15.0
20
Hz
Operating current
200A, 50C ambient
180
200
220
A
Operating voltage
200A, 50C ambient
12.2
12.9
13.5
V
Center wavelength
200A, 50C ambient
--
1064
--
nm
Beam M²
200A, 50C ambient
--
--
5
Focal power density
200A, 50C ambient
200
--
--
GW/cm²
Working distance
200A, 50C ambient
3
5
10
mm
--
50
--
ºC
Operating temperature
Copyright © 2010 Princeton Optronics, Inc. All Rights Reserved. Princeton Optronics reserves the right to change product design and specifications at any time without notice. No license is granted by implication or otherwise under any patents or patent right of Princeton Optronics. No responsibility is assumed for the use of these products, nor for any infringement on the rights of others resulting from the use of these products
Laser diode product components are intended for use in a user-devised end system. However, these products are capable of emitting Class IIIB radiation. Extreme care must be exercised during their operation. Only persons familiar with the appropriate safety precautions should operate a laser product. Directly viewing the laser beam or exposure to specular reflections must be avoided. Serious injury may result if any part of the body is exposed to the beam. The eye is extremely sensitive to the infrared radiation and therefore, proper eye-wear must be worn at all times. Use of optical instruments with these products may increase eye hazard. Always wear eye protection when operating.
>100mW
IV
REV. A – May 2015
Princeton Optronics, Inc. * 1 Electronics Drive * Mercerville, New Jersey 08619 Voice: (609) 584-9696 * Fax: (609) 584-2448 * E-mail:
[email protected] * www.princetonoptronics.com
High Power VCSEL Pumped Solid State Laser Product # PR-LSIG-12-W1064
Mechanical Diemensions:
Copyright © 2010 Princeton Optronics, Inc. All Rights Reserved. Princeton Optronics reserves the right to change product design and specifications at any time without notice. No license is granted by implication or otherwise under any patents or patent right of Princeton Optronics. No responsibility is assumed for the use of these products, nor for any infringement on the rights of others resulting from the use of these products
Laser diode product components are intended for use in a user-devised end system. However, these products are capable of emitting Class IIIB radiation. Extreme care must be exercised during their operation. Only persons familiar with the appropriate safety precautions should operate a laser product. Directly viewing the laser beam or exposure to specular reflections must be avoided. Serious injury may result if any part of the body is exposed to the beam. The eye is extremely sensitive to the infrared radiation and therefore, proper eye-wear must be worn at all times. Use of optical instruments with these products may increase eye hazard. Always wear eye protection when operating.
>100mW
IV
REV. A – May 2015
Princeton Optronics, Inc. * 1 Electronics Drive * Mercerville, New Jersey 08619 Voice: (609) 584-9696 * Fax: (609) 584-2448 * E-mail:
[email protected] * www.princetonoptronics.com
High Power VCSEL Pumped Solid State Laser Product # PR-LSIG-12-W1064 Option-1: laser driver
• • • • • • • • • • •
Input Voltage: + 24VDC Interface Connector: 15 Pin “D” Sub Female Pulse Enable: +5V TTL to +15V CMOS Output Power: 75 watts average Output Pulse current: 200A Pulse Width Range: 20usec to 2msec Max Rep Rate: 10kHz Rise/Fall Time: 10uSec Current Regulation: 1.0% Current Ripple: <0.5% Current Overshoot: <5%
Option-2: power supply • 24V DC power supply for multiple drivers.
Option-3: customized mount. • Customized mounting tube fits specified openings • Glass or lens seal from harsh environments • Customized beam delivery optics to meet specified working distance.
Copyright © 2010 Princeton Optronics, Inc. All Rights Reserved. Princeton Optronics reserves the right to change product design and specifications at any time without notice. No license is granted by implication or otherwise under any patents or patent right of Princeton Optronics. No responsibility is assumed for the use of these products, nor for any infringement on the rights of others resulting from the use of these products
Laser diode product components are intended for use in a user-devised end system. However, these products are capable of emitting Class IIIB radiation. Extreme care must be exercised during their operation. Only persons familiar with the appropriate safety precautions should operate a laser product. Directly viewing the laser beam or exposure to specular reflections must be avoided. Serious injury may result if any part of the body is exposed to the beam. The eye is extremely sensitive to the infrared radiation and therefore, proper eye-wear must be worn at all times. Use of optical instruments with these products may increase eye hazard. Always wear eye protection when operating.
>100mW
IV
REV. A – May 2015
Princeton Optronics, Inc. * 1 Electronics Drive * Mercerville, New Jersey 08619 Voice: (609) 584-9696 * Fax: (609) 584-2448 * E-mail:
[email protected] * www.princetonoptronics.com
