High Wall Units

Transcript

HIGH WALL UNITS °C °F A B l I Fee Start Stop Sleep 1 2 3 Daily -JET TURBO MY ECONO English-Operation Instruction for Remote Control TAC-292 French-Instruction d'opération pour la télécommande TAC-292 Spanish-Instrucción de la operación para el mando a distancia TAC-292 600 SERIES 421 02 9217 00 Composite June 2006 Composite Introduction Dear Customer, ● ● We would like to congratulate you for purchasing one of our company's new air conditioners . The air conditioner enables you to control your environment and adjust it to your personal preference. IMPORTANT 1. Duct free systems should be installed by authorized personnel only, using approved tubing and accessories. If technical assistance is needed, please contact the installer. 2. You should read the operating instructions carefully and follow them accordingly in order to maximize the air conditioner's performance. Warning! If the main power supply cable is damaged, please contact a qualified electrician to replace it in order to prevent unnecessary risks. Model Cooling DFS2A309J1A DFS2A312J1A DFS2A318K1A DFS2A324K1A DFS2A330K1A DFS2A336K1A DFS2A318J2A DFS2A324J2A Heat Pump DFS2H309J1A DFS2H312J1A DFS2H318K1A DFS2H324K1A DFS2H330K1A DFS2H336K1A DFS2H318J2A DFS2H324J2A Table of Contents Introduction _________________________________________________________________________________ 1 Remote Control ______________________________________________________________________________ 2 For Beginners - Summer Operation _______________________________________________________________ 3 For Beginners - Winter Operation ________________________________________________________________ 5 Selecting fan speed and air conditioning modes _____________________________________________________ 7 Selecting air conditioner modes __________________________________________________________________ 8 Setting the real time clock on the remote ___________________________________________________________ 9 Additional Functions: Automatic Mode ___________________________________________________________ 10 Additional functions - Energy management ________________________________________________________ 11 Additional Functions: Using the 'I Feel Sensor' _____________________________________________________ 12 Additional Functions: Adjusting air outlet grill - Sweep Mode _________________________________________ 13 Additional functions: Switching ON automatically at a later time - Delay ________________________________ 14 Additional Functions: Switching ON/OFF several times during the day __________________________________ 15 Additional functions: Detailed explanation on setting time periods _____________________________________ 16 Battery installation ___________________________________________________________________________ 17 Additional functions: Detailed explanation for Sleep Mode settings _____________________________________ 17 Technician related functions ____________________________________________________________________ 18 Operating the Air Conditioner from the Display Panel _______________________________________________ 19 Air Conditioner Display Panel __________________________________________________________________ 20 Cleaning and Maintenance _____________________________________________________________________ 21 Troubleshooting _____________________________________________________________________________ 22 For Technician/Service ________________________________________________________________________ 23 Loading the remote control with batteries, The remote control must be loaded with two AAA batteries (see page 17). To switch display from Fahrenheit to Celsius, please see page 18. 421 02 9217 00 1 Remote Control INFRARED SIGNAL TRANSMITTER WINDOW DESIRED TEMPERATURE TEMPERATURE SENSOR TRANSMISSION INDICATOR LOW BATTERY INDICATOR °F OPERATING MODES: COOLING, FAN, HEATING, DEHUMIDIFICATION, AUTO A B FAN INDICATORS LOW, MEDIUM, HIGH, AUTO SWEEP INDICATOR I Feel SENSOR ACTIVE INDICATOR ENERGY INDICATOR 1 2 3 Start CLOCK Stop TIMER START/STOP ONE-TIME/DAILY INDICATORS Sleep Daily SLEEP INDICATOR ON/OFF BUTTON FLAP DOOR HEATING MODE BUTTON UP/DOWN BUTTON ECONOMY TURBO-JET ECONOMY BUTTON COOLING MODE BUTTON TURBO-JET BUTTON ° F A B I Feel Start Stop *SELECTION BUTTON (ENTER) 1 2 3 Sleep Daily *UP(+)/DOWN(-) SELECTION BUTTON SEL *RIGHT/LEFT SELECTION BUTTON TIMER CLEAR SWEEP *TIMER CLEAR BUTTON *SWEEP BUTTON I FEEL DELAY *I FEEL BUTTON *DELAY BUTTON *Button functions when flap door is open 2 421 02 9217 00 For Beginners - Summer Operation Beat the Heat! There is nothing to it! Press the Blue button on the remote control - and the air conditioner will start cooling. Important! Max distance from remote to air conditioner should not exceed 4.6m (15 feet). Displayed symbols The air conditioner will cool to a temperature of 22°C (71.6°F). The remote control sends a command to the air conditioner. (The air conditioner beeps to confirm). The "snowflake" symbol shows that the air conditioner is cooling. The air outlet grill (fixed or moving). Detailed explanation on page 11. The FAN is spinning at automatic speed ECONOMY (The FAN symbol spins). TURBO-JET The time is now 23:45 Switching the air conditioner OFF
Press the red ON/OFF button . Displayed symbols The current room temperature is 23°C (73°F). A command is sent to the air conditioner. (The air conditioner beeps to confirm). The "In-house thermometer" symbol continuously measures room temperature. The time is now 23:45 ECONOMY TURBO-JET Switching the air conditioner ON again If you wish to switch the air conditioner ON again you have the following two options: A. Press the blue button . The air conditioner will start cooling down to 22°C (71.6°F) once again,using its default settings,with the fan on automatic mode. B. Press the red ON/OFF button . The air conditioner will start running at the same settings as it was set before being switched off . 421 02 9217 00 Always point the remote at the air conditioner AIR-CONDITIONER BEEP JET BOTUR Y NOM ECO 3 For Beginners - Summer Operation Changing the fan speed To increase air volume To minimize air volume TURBO-JET
Press the air volume. ECONOMY TURBO-JET button for maximum Displayed symbols on the remote control
Press the ECONOMY button for low, economical and quiet speed. Displayed symbols on the remote control A command is sent to the air conditioner. (The air conditioner beeps to confirm). A command is sent to the air conditioner. (The air conditioner beeps to confirm). °C The fan spins at high speed ECONOMY TURBO-JET The fan spins at low speed ECONOMY TURBO-JET If you wish to change the air conditioner's set temperature (warmer/cooler)
Press the button with the minus sign Each time you press the minus button Each time you press the plus button 4 or the button with the plus sign . the temperature is reduced (cooler) by one degree centigrade. the temperature is increased (warmer) by one degree centigrade. 421 02 9217 00 For Beginners - Winter Operation Stay warm in the winter time. There's nothing to it! Press the red button on the remote control - and the air conditioner will start heating. Displayed symbols Room temperature is set to 23°C (73°F). °C A command is sent to the air conditioner (The air conditioner beeps to confirm) The "sun" symbol indicates that the air conditioner is in heat mode. The air outlet grill (fixed or moving) Detailed explanation on page 11. The fan is spinning at an automatic speed. ECONOMY TURBO-JET The time is now 23:45 Switching the air conditioner off
Press the red on/off button . Displayed symbols The current room temperature is 21°C (69.8°F). °C A command is sent to the air conditioner (The air conditioner beeps to confirm). The "In-house thermometer" symbol continuously measures room temperature. The time is now 23:45 ECONOMY TURBO-JET Switching the air conditioner on again If you wish to switch the air conditioner on again, you have the following two options: A. Press the red button Always point the remote at the air conditioner . The air conditioner will start heating up to 23°C (73°F) once again, using its default settings, with the fan on automatic mode. B. Press the red on/off button AIR-CONDITIONER . The air conditioner will start running at the same settings as BEEP it was set before being switched off. 421 02 9217 00 JET BOTUR Y NOM ECO 5 For Beginners - Winter Operation If you wish to change the air conditioner's set temperature (warmer/cooler)
Press the button with the minus sign Each time you press the minus button Each time you press the plus button or the button with the plus sign . the temperature is reduced (cooler) by one degree centigrade. the temperature is increased (warmer) by one degree centigrade. Changing the fan speed To minimize air volume To increase air volume TURBO-JET
ECONOMY Press the TURBO-JET. Turbo-Jet button for maximum air volume.
Press the ECONOMY button for low, economical and quiet speed. Displayed symbols Displayed symbols A command is sent to the air conditioner (The air conditioner beeps to confirm). A command is sent to the air conditioner (The air conditioner beeps to confirm). The fan spins at low speed The fan spins at high speed ECONOMY TURBO-JET ECONOMY TURBO-JET Important The units are designed to work in heat mode only down to -10°C (14°F) outdoor ambient temperature. If at starting time outdoor temperature is equal or lower than -10°C (14°F) the unit will not start and the filter led will flash five (5) times to indicate that low temperature protection is activated. 6 421 02 9217 00 Selecting fan speed and air conditioning modes Important During any programming process, if next step is not selected for over 10 seconds, the remote will exit from programming back to previous settings. SEL SE SEL SE Changing the fan mode SEL SE There are 4 fan speed modes: Low speed Medium speed High speed SEL I FEEL TIMER CLEAR and Automatic speed (the blades spin) ECONOMY SWEEP TURBO-JET DELAY Open the flap door of the remote control. the fan symbol start blinking.
Press the SEL button With every press of the SEL . SEL button the fan's speed will change and SEL the air conditioner will beep: Low speed Pull to open the flap door, the fan symbol start blinking Medium speed High speed Automatic speed ( ). Once you close the flap the selected symbol will stop blinking. Changing the air conditioner operation mode Cooling Mode (snowflake symbol) - The air conditioner will cool according to the set temperature, while drying and filtering the room air. Fan Mode (fan symbol) - The air conditioner circulates and filters the air, without changing room temperature. Heating Mode (sun symbol) - The air conditioner heats according to the set temperature and filters the room air. ECONOMY The operational modes appear in a single line on the remote control’s display TURBO-JET Dehumidify Mode (drop symbol) - The air conditioner dries and filters the room air, while cooling it slightly. Automatic Mode (the letter ) - The air conditioner heats or cools the room air, according to the selected set temperature: If the room is colder than the desired temperature - the air conditioner will automatically change to heat mode. If the room is warmer than the desired temperature - the air conditioner will automatically change to cool mode. See further explanation in Automatic section ( ) on page 9. Changing operation mode Displayed symbols Open the flap door. Fan symbol will blink. SEL TIMER CLEAR SWEEP ECONOMY I FEEL DELAY TURBO-JET Fan symbol blinks. Always point the remote at the air conditioner Select Button SEL Left -Right navigation buttons Up-Down navigation buttons SEL SEL AIR-CONDITIONER SEL TIMER CLEAR SWEEP BEEP I FEEL DELAY JET BOTUR Y NOM ECO 421 02 9217 00 7 Selecting air conditioner modes ❶
Press the plus sign button once to move to the operating modes section. One of the operating modes blinks. For example - ❶ heating mode blinks. SEL I FEEL TIMER CLEAR SWEEP ❷
Press right or left DELAY buttons to select the desired operating mode. SEL ❷ ❸
When you have selected the desired mode, press the SEL TIMER CLEAR I FEEL SWEEP DELAY SEL button to select that mode. SEL TIMER CLEAR ❸ Close the Flap door. SWEEP I FEEL DELAY Note: You can select the operating mode on the remote control even if the air conditioner is not currently on. Later, switch the airconditioner on by pressing the on/off button and the air conditioner will function according to the mode you selected. If you did not press any buttons or make any selections for ten (10) seconds, the fan symbol will blink again (the initial mode when you opened the flap). Always point the remote at the air conditioner Select Button SEL Left -Right navigation buttons Up-Down navigation buttons SEL SEL AIR-CONDITIONER SEL TIMER CLEAR SWEEP BEEP I FEEL DELAY JET BOTUR Y NOM ECO 8 421 02 9217 00 Setting the real time clock on the remote Fan symbol blinks Open the flap on the remote control. Once you open the flap, the remote control's display will show the last mode you were in. The fan symbol blinks. SEL SWEEP ❶
Press the minus sign button ECONOMY I FEEL TIMER CLEAR TURBO-JET DELAY once to go down to the clock symbol. The symbol blinks. 1 Start Sleep Daily SEL I FEEL TIMER CLEAR ❶ ❷
Press the SEL button SWEEP DELAY - mode selection. The hours and SEL minutes symbol blinks (- - - -). 1 Start Sleep Daily For quick time change Pressing the plus sign button or the minus sign button continuously moves the clock forward or backward rapidly. SEL ❷ I FEEL TIMER CLEAR SWEEP DELAY One press is one minute Pressing the plus sign button or the minus sign button only once moves the clock one minute forward or backward. Start 1 Sleep Daily For example, set the time to be 23:45. SEL I FEEL TIMER CLEAR ❸
Press the minus sign button ❹
Press the SEL button SWEEP until the digits 23:45 appear and blink. ❸ (-)minus 1 minute SEL DELAY (+) plus 1 minute - mode selection and close the flap door. Start The new hour is set. 1 Sleep Daily SEL ❹ Always point the remote at the air conditioner Select Button SEL I FEEL TIMER CLEAR SWEEP DELAY Left -Right navigation buttons Up-Down navigation buttons SEL SEL AIR-CONDITIONER SEL TIMER CLEAR SWEEP BEEP I FEEL DELAY JET BOTUR Y NOM ECO 421 02 9217 00 9 Additional Functions: Automatic Mode Select Automatic mode to keep constant temperature comfort all year round. In this mode, the unit will operate at the selected temperature setting and will automatically select the required operation mode and fan speed to maintain this setting. When required, the unit will automatically switch between cooling, fan and heating modes. SEL TIMER CLEAR SWEEP ECONOMY I FEEL TURBO-JET DELAY To select Automatic mode: ❶
Open the flap door, press the plus sign button to move to the operating mode section. ❶ SEL I FEEL TIMER CLEAR SWEEP ❷
Press the right button until DELAY symbol blinks. ❷ SEL I FEEL TIMER CLEAR SWEEP ❸
Press the SEL SEL DELAY button to set the unit to auto mode and close flap door. SEL ❸ Always point the remote at the air conditioner Select Button SEL TIMER CLEAR SWEEP I FEEL DELAY Left -Right navigation buttons Up-Down navigation buttons SEL SEL AIR-CONDITIONER SEL TIMER CLEAR SWEEP BEEP I FEEL DELAY JET BOTUR Y NOM ECO 10 421 02 9217 00 Additional functions - Energy management Important Energy management is optional and exists only in some models To operate this fuction: Open flap door, to reach energy symbol press right button press SEL button SEL , to change between energy mode, SEL ECONOMY I FEEL TIMER CLEAR SWEEP TURBO-JET DELAY close flap door. You have three (3) optional energy modes: 1. Auto mode- when using this mode, the control will automatically choose energy state (econo or full), according to room temperature and weather conditions. 2. Full capacity- when using this mode, the unit will work continuously in full capacity. 3. Econo mode- when using this mode, the unit will work continuously in half capacity. Always point the remote at the air conditioner Select Button SEL Left -Right navigation buttons Up-Down navigation buttons SEL SEL AIR-CONDITIONER SEL TIMER CLEAR SWEEP BEEP I FEEL DELAY JET BOTUR Y NOM ECO 421 02 9217 00 11 Additional Functions: Using the 'I Feel Sensor' The 'I feel' feature enables you to maintain desired temperature through a special sensor located on the remote instead of the default sensor located on the unit. °C To operate this feature: ❶
Open the flap door. I Feel I FEEL once during unit's operation. Press the blue button SEL Below the "in house thermometer" symbol , I Feel will appear. TIMER CLEAR I FEEL SWEEP DELAY ELAY I FEEL To quit this feature, press the blue button I FEEL once again. ❶ If you wish to display room temperature on the remote: When the air conditioner is switched OFF Room temperature (near the remote control) is displayed continuously. SEL TIMER CLEAR SWEEP ECONOMY I FEEL TURBO-JET DELAY When the air conditioner is ON, I Feel Open the flap door ❶
❷
Press the right button once. The HOUSE symbol will blink. Press the SEL SEL I FEEL TIMER CLEAR SWEEP SEL button - and the room temperature will be I Feel displayed on the remote control for ten (10) seconds. SEL TIMER CLEAR SWEEP 12 ❶ DELAY I FEEL ❷ DELAY 421 02 9217 00 Additional Functions: Adjusting air outlet grill - Sweep Mode Changing the horizontal louver's position
To change louver from fixed position to automatic sweep mode, open the flap door, SWEEP press the gray SWEEP button once. SEL TIMER CLEAR SWEEP
ECONOMY I FEEL TURBO-JET DELAY The SWEEP symbol will blink and change position continuously. The sweep louver on the air-conditioner will move up and down continuously. . To change the angle of the air louver: ❶
Open the flap door, SWEEP , press the sweep button 1 Start Sleep Daily wait until the symbol shows the desired angle, SEL SWEEP press the swep button again and close the flap door. I FEEL TIMER CLEAR SWEEP Changing the angle of the vertical louvers (left-right) is done by using the handles near the air-vent (see air-conditioner operating manual). DELAY ❶ °C Start 1 Sleep Daily SEL TIMER CLEAR SWEEP I FEEL DELAY ❶ Important information! Our summer recommendation: position 6 ∂ Cold air tends to sink, while hot air tends to rise – therefore: Our winter recommendation: position 2 ≤ Always point the remote at the air conditioner AIR-CONDITIONER BEEP JET BOTUR Y NOM ECO 421 02 9217 00 13 Additional functions: Switching ON automatically at a later time - Delay If you want the air conditioner to switch itself ON or OFF automatically at a later time (only once). SEL TIMER CLEAR For example: SWEEP ECONOMY I FEEL TURBO-JET DELAY The air conditioner is ON and you want to switch it OFF automatically in two hours time: Open the flap on the remote control. ❶
DELAY Press the DELAY button . °C The hours:minutes symbol will blink (- - : - -). You are at Stop 1 Start 1 Sleep Daily ❷
DELAY Press the DELAY button SEL TIMER CLEAR I FEEL SWEEP DELAY four times to program switching OFF ❶ in two hours time (02:00 on the display). If you made a mistake, never mind! °C Just repeat the procedure once again and correct it. DELAY , you will add thirty (30) Every time you press the DELAY button Start minutes to the delayed operation time frame. You can also change the delayed or minus operation time using the buttons. SEL TIMER CLEAR I FEEL SWEEP ❸
1 Sleep Daily DELAY x4 ❷ When the mode you desire blinks, press the SEL button and close the flap on the remote control. SEL On the display, instead of the regular clock, you will see a timer that shows how much time remains before switching OFF. This timer is updated every minute. The timer shows - 02:00 Stop 1. (Switching OFF in two hours). SEL I FEEL TIMER CLEAR
To cancel any delay settings, start or stop, just push the red on/off button once. SWEEP DELAY ❸ If the air conditioner is currently OFF you can delay the switch ON time - Start 1 will appear. If the air conditioner is currently ON you can delay the switch OFF time - Stop 1 will appear. 1 Stop In order to know the current time, open the flap, press the minus button Timer instead of the clock and you will see the time blinking. ECONOMY Always point the remote at the air conditioner Select Button SEL TURBO-JET Left -Right navigation buttons Up-Down navigation buttons SEL SEL AIR-CONDITIONER SEL TIMER CLEAR SWEEP BEEP I FEEL DELAY JET BOTUR Y NOM ECO 14 421 02 9217 00 Additional Functions: Switching ON/OFF several times during the day The remote control enables you to start/stop automatically three times in 24 hours. Additional 'sleep time' zone are also available. Very Important! To make sure this function operates properly you must set the clock to the current real time. A few examples: You can program the air conditioner to switch ON automatically in 3 hours and switch OFF 4 hours afterwards. You can program the air conditioner to switch ON at 08:00 and switch itself OFF at 10:30, and later, it will switch ON again at 13:00 and OFF again at 17:30. You can program the air conditioner to switch ON every day at 08:30 in the morning. You can program the air conditioner to gradually decrease cooling temperature during the night, starting at 22:00. ❶
❷
To start timer settings : open flap door and press the minus button . 1 Start The clock starts blinking. Sleep Daily SEL Press the right button . The programming row blinks and Start 1 will appear. I FEEL TIMER CLEAR SWEEP ❶ DELAY If any of the time zones was pre-programmed, the clock will show the pre-programmed time. If you wish to keep the pre-programmed time as is and continue searching through the time periods Each push on SEL button SEL , will take you to the next programming time. 1 Start Sleep Daily c Important - The clock is active but not shown during the setting of the timer. SEL ❷ I FEEL TIMER CLEAR SWEEP DELAY If you want to set or change the time which is currently displayed ❸
Use the plus / minus button, until your desired real time is selected. For example: The first press of the plus button shows 0:10. Therefore, the air conditioner will switch itself ON ten (10) minutes after midnight. Once you close the flap door, the timer will show you how long before the air conditioner will switch itself ON. Start 1 Sleep Daily ❸ SEL If you chose 00:10 as the first start time. I FEEL TIMER CLEAR SWEEP ❹
Press the SEL button SEL DELAY - and close the flap door. The air conditioner will start automatically at 00:10. Start Pay attention: Every time you press the SEL button SEL , you move on to the next 1 Sleep Daily time period. SEL I FEEL TIMER CLEAR If you made a mistake, never mind! Just repeat the procedure once again and correct it. Always point the remote at the air conditioner Select Button SEL SWEEP ❹ DELAY Left -Right navigation buttons Up-Down navigation buttons SEL SEL AIR-CONDITIONER SEL TIMER CLEAR SWEEP BEEP I FEEL DELAY JET BOTUR Y NOM ECO 421 02 9217 00 15 Additional functions: Detailed explanation on setting time periods If you want the air conditioner to switch ON/OFF only once: If you want the air conditioner to switch ON/OFF every day (daily feature):
Perform all the actions as in the single switching ON/OFF procedure (Follow arrow). Press the minus sign button The clock starts blinking. Press the right button . The programming row starts blinking and 'Start 1' appears.
Program the switch ON time using the and
Press the right button twice. The word DAILY blinks. The word DAILY indicates buttons. that all the time periods you chose or will choose are set daily. Press the SEL button SEL in order to set the start time. Every press of this button moves you to the next time period. Continue and program, if needed, the second time period Start2/Stop2 and the third period Start3/ Stop3 till you finish programming all the Start/ Stop time periods you want.
Press the SEL button SEL in order to program daily automatic switching ON (including Sleep) Once you close the flap door on the remote control the DAILY symbol will appear, which is active for all time periods (including Sleep). Pay attention: Once you close the flap door, the timer will appear and will show the time left to next start/stop programmed session. SEL TIMER CLEAR SWEEP I FEEL DELAY Pay attention: If at the time of selection, the air conditioner has already been in the programmed time, the remote control will skip the action you choose. If you wish to cancel all the time periods you programmed: TIMER CLEAR Press the TIMER CLEAR button 16 continuously for 5 seconds - this cancels a time period. 421 02 9217 00 Additional functions: Detailed explanation for Sleep Mode settings Sleep mode routine - what is it? If the air conditioner is cooling, the temperature will rise by one (1) degree per hour, or maximum two (2) degrees from the original set temperature selected. If the air conditioner is heating, the temperature will drop be one (1) degree per hour, for maximum two (2) degrees from the original set temperature selected. If you want Sleep mode to operate every day: (Daily feature) If you want Sleep mode to operate only once:
Press the minus sign button If DAILY has already been selected, stop here. If DAILY has not been selected, perform all the actions in the single Sleep mode operation (Follow the arrow) . The clock starts blinking.
Press the right button twice. The programming row starts blinking and 'Start 1' appears.
In this state the FAN symbol blinks Press the SEL button SEL in order to select
a switch ON time.
and
Press the SEL button SEL buttons.


Press the SEL button and SEL three (3) times. Press the SEL button SEL in order to set automatic, daily switching ON time of the air conditioner, according to the time you set for Sleep mode. The Stop time is activated. Program the switch OFF time using the Press the right button The word DAILY starts blinking. in order to set the switch ON time and to move to the switch OFF time.
. The clock starts blinking. The Start time is activated. Program the switch ON time using the Press the minus button buttons. Once you close the flap door on the remote control, the Daily and Sleep symbols will appear each time the time period is active. in order to set the switch OFF time. Battery installation ✓ Remove the battery compartment cover by sliding it off. ✓ Insert two Alkaline AAA 1.5V batteries into the battery compartment, making sure to follow the polarity markings inside the battery compartment. ✓ Replace battery compartment cover. ✓ Replace batteries whenever 'Low Battery' indicator appears. Important After battery replacement, all last settings are re-gained, except timer programming, which might not be saved. 421 02 9217 00 °C 17 Technician related functions For a technician or an experienced user The air conditioner has additional options that can be reached using simultaneous pressing of two buttons: When there are two air conditioners with two separate remote controllers installed in the same room, you might want to change the frequency on one of the remote to differentiate the control between the units. Open the flap door, press both the right and the left buttons simultaneously for three (3) seconds. Instead of the letter A, B will appear on the upper left side of the display. To return to A, repeat the procedure again. °C A B Changing from degrees Centigrade to degrees Fahrenheit: and the buttons simultaneously for five (5) Open the flap door, press both the seconds. To return to degrees Centigrade again - repeat the procedure again. Activating the energy feature Note: This feature is available only in some models. To activate: open flap door and press SWEEP 5 sec. SEL SWEEP DELAY and DELAY buttons TIMER CLEAR I FEEL SWEEP DELAY To show all the symbols on the display: and 5 sec. SEL symbol will apear on the display. simultaneously for five (5) seconds, To return to previous setting, repeat the procedure again. Open the flap door, press the left 3 sec. SEL buttons simultaneously for three seconds. SEL 3 sec. Display will reset to previous setting after ten (10) seconds. To lock the remote control: Open the flap door, press the right and 3 sec. buttons simultaneously for three seconds. SEL LOC will appear on the display instead of the clock. To unlock, repeat again. Proper air conditioner operation Do: ✓ Make sure the air conditioner is connected directly to the electricity. ✓ Replace both batteries in the remote control when the low battery signal appears ( ). ✓ When you send a command to the air conditioner, point the remote control towards the air conditioner display from a maximum distance of 15 feet. ✓ Choose a moderate operational temperature. Extreme temperatures cause waste of energy. ✓ Close windows and doors. ✓ If a problem arises and you are not able to solve it, call an authorized technician. Don't: ✗ Before performing any maintenance or cleaning operation, make sure the air conditioner is disconnected from the main power. ✗ Do not expose the remote control to direct sunlight or heat. ✗ Do not expose the air conditioner display panel to sunlight or strong lighting, it could interfere with signal reception from the remote control. ✗ Do not block the incoming and outgoing air vents of the internal or external units. 18 421 02 9217 00 Operating the Air Conditioner from the Display Panel Turning the Air-Conditioner On (AUTO Mode) ✓ Raise the grill of the air-conditioner. ✓ Press the Operation push button (AUTO Mode). In the AUTO Mode the air-conditioner will work at a constant temperature setting of 23°C (73°F), by automatically selecting the required operation mode and a constant FAN speed. Turning the Air-Conditioner Off ✓ Press the Operation push button once again. Returning to Remote Controller Operation: Operate the air-conditioner from the Remote Controller. FUSE FUSE AUTO/OFF FILTER RESET SERVICE LED POWER/AIRCOND AUTO/OFF FILTER RESET TIMER FILTER IR RECEIVER SERVICE LED OPERATION PUSH BUTTON (I) 421 02 9217 00 19 Air Conditioner Display Panel The LEDs on the display panel provide alerts regarding various operations and malfunctions. The display panel features are described in the following table: Feature Use/Description A I.R. Receiver ● Receives transmissions from the remote control. B Filter LED ● Lights every 250 hours of unit operation to remind you to check the air filters' cleanliness. Flashes five (5) times to indicate that low temperature protection is activated. ● C Green Operation LED ON ● Lights when the air conditioner is operating. Flashes during defrost, in heat mode or during routine thermostat state. D Timer LED ● Lights when TIMER feature is operated. E ● Lights when the air conditioner is OFF and connected to power supply at the proper voltage. Flashes (red LED) at a constant rate if there's a malfunction. Red Power LED ● ● G Service LED ● Flashes at different rates according to the malfunction. (See detailed information on page 23). I ● Turns the air conditioner ON/OFF without remote control (AUTO mode). Press momentarily the ON/OFF button to turn the air conditioner ON without the remote control (AUTO mode). Press and hold for five seconds to reset filter LED (B) or to cancel malfunction indicator (G). Operation Push button ● FUSE AUTO/OFF FILTER RESET I SERVICE LED G E C OFF ON TIMER D B A FILTER IR RECEIVER 20 421 02 9217 00 Cleaning and Maintenance Warning Danger of Electrical Shock! Before performing any cleaning or maintenance operation on the air conditioner, disconnect the unit from the power supply source. Cleaning Air Filters ✓ After approximately 250 hours of operation (about a month), you need to remove and clean the filters. ✓ Please note: In a very dusty environment, the filters should be cleaned more often. ✓ After removing the filters: vacuum out the dust, wash them with warm soapy water, dry and put them back in place. POWER/AIRCOND TIMER FILTER IR RECEIVER Air Care special filters for better air quality 1. The filters can be re-used several times 2. Wash and dry these filters once every season. 3. With regular use, the filters must be replaced every five (5) years. In more extreme conditions, the filters must be replaced every year. 4. The filters will not be effective if they are not replaced on time. Turning OFF the Filter LED ✓ Hold down the Operation switch button (I) for five (5) seconds and turn on the air conditioner with the remote control. FUSE AUTO/OFF FILTER RESET OFF ON PRESS FOR 5 SEC. TO RESET THE FILTER LED TIMER FILTER IR RECEIVER FILTER LED 421 02 9217 00 21 Troubleshooting The air conditioner has been designed for outstanding reliability and requires very little maintenance. However, smooth operation could be disrupted by a malfunction in the electrical system or incorrect operation. You can try to solve the problems caused by simple malfunctions by referring to the table below. If the malfunction persists, call a qualified service technician. Problem Air conditioner does not work. Possible Solution Possible Causes ● ● ● ● No command command was was transmitted transmitted to the air No air conditioner. conditioner. Airconditioner conditionerdid did not not receive a transmitted Air transmitted command. command. ● ● ● ● ● POWER LED is not lit. ● ● ● ● ● ● ● FILTER LED is lit. ● ● ● conditionerisisworking, working,but but Air conditioner does not notperform performthethe required does required operation. ● ● ● ● Operation C isflashes. constantly lit. OFF LED LED E (red) ● ● ● Press the transmit button. Make sure that the remote control control is is aimed at the air conditioner conditioner when when transmitting commands. Check electrical connection. Check electrical outlet byconnection. connecting another appliance. Check outlet by connecting another Call service personnel. appliance. Reset interrupter. Call service personnel. Airconditioner conditionerisisnot notproperly properlyplugged connected Air in. to power outlet source.is defective. Electrical Electrical outlet is defective. Fuse burned out. Automatic interrupter switched Off. Fuse burned out. ● ● Checkrequire filter's cleanness Filters cleaning.and clean if required Desired temperature setting is higher than room air temperature when operating in the COOLING mode. 1. Remove and clean filters. 2. Hold the Operation (I) pushbutton Holddown down the Operation (I) for five (5) seconds. pushbutton for five (5) seconds. Desired temperature temperature setting setting is higher than Desired than roomair airtemperature temperature when operating in the room the HEATING mode. mode. COOLING The air-conditioner operating. Desired temperatureissetting is lower than room air temperature when operating in the HEATING mode. ● ● Lower the desired temperature setting. setting. ● ● Raise the desired temperature setting. Electronic control detected possible The control system is malfunctioning. malfunctioning. There is no direct line of sight between the remote control and the air conditioner. ● ● Hold the Operation (I) pushbutton Holddown down the Operation (I) for five (5) seconds. pushbutton for five (5) seconds. Restart air control conditioner. the Place thethe remote where itIfhas a problem persists, call qualified direct line of sight to the airaconditioner. technician. ● ● ● ● ● ● Operation LED C is flashing. ● ● The air air conditioner conditioner reached reached the its desired The desired temperature. The is readywas to temperature and compressor the compressor restart, but there noby demand for it. automatically shutisoff the thermostat. ● ● This is normal operation. There is is no no need for any corrective action. Various indicator LEDs behave Air conditioner does not operate differently from control. what appears on with the remote page 18. ● ● The remote controloris malfunction. malfunctioning. Incorrect operation ● ● Operate the air the conditioners with (I) the Hold down Operation Operation (button/switch). pushbutton(I)forcontrol five (5) seconds. Replace Restart the thebatteries. air conditioner. If the problem persists, call service personnel. Air conditioner does operate The remote control ofnot another air with the remote control. conditioner interferes with your air conditioner's operation. ● ● ● The batteries are low. ● ● Bothbatteries remote controls The are low. are transmitting on the same frequency. The remote control is malfunctioning. ● ● The remote control of another air ● Both remote controls are transmitting on the conditioner interferes with your same frequency. air conditioner’s operation. Technician/Service - Malfunction Displays on the next page ● 22 ● ● See pagethe 18,batteries. Frequency change on the Replace Remote Operate Control. the air conditioners with the Operation (I) control (button/switch). See page 16, Frequency change on the Remote Control. 421 02 9217 00 For Technician/Service For each malfunction, LED E (red) flashes at a constant rate: Malfunction Indication Display FUSE AUTO/OFF FILTER RESET G Service LED E OFF OFF ON OF TIMER FILTER IR RECEIVER Malfunction Indicator LED The malfunction can be diagnosed according to the rate at which the G Service LED is flashing Pull up the front cover of the air conditioner to see the service led. Malfunction Display LED - LED E (red) flashes at a constant rate, as follows: TH1 Malfunction (Short circuit or break) ● 1 short pulse TH2 Malfunction (Short circuit or break) ● 2 short pulses Low Pressure Malfunction ● 3 short pulses High Pressure Malfunction ● 4 short pulses Low Voltage Malfunction ● 5 short pulses High Voltage Malfunction ● 6 short pulses 421 02 9217 00 23 Copyright 2006 ICP International Comfort Products Composite A.M.N 0106 ● HIGH WALL 5130-2618913 Printed in Israel