Transcript
IM a G IN AT ION INNO VAT ION INT EG R ATI O N
ETHERNET OVER COAX adaptor
NEW PHOTO
HIGHWIRE™ allows IP network cameras to communicate over existing coax cables Simple retro-fit of IP cameras in place of analogue Full 100 BaseT Ethernet performance Uses legacy cabling - cuts installation costs Supports multiple IP cameras Supports mega-pixel cameras Fully automatic - no configuration required Up to 300m on RG59, 500m on RG6 Powered by legacy PSU at camera end Rack mount option for control room end
I Ma G IN AT I O N I N NO VAT I O N I N T E G RAT ION
High - Speed Ethernet over video cable
Why HIGHWIRE cuts installation costs
Signal Converter
Simple Installation
HIGHWIRE turns any existing analogue
HIGHWIREs are used in pairs and
video cable (co-ax) into a high-speed
installing them is extremely simple. One
• Uses legacy analogue video cabling
Ethernet connection. This allows multiple
HIGHWIRE unit is connected to each
• Supports multiple IP cameras
networked IP cameras to replace a
end of the co-axial cable with the BNC
• Supports mega-pixel cameras
single analogue CCTV camera, without
connectors, thus providing a straight
• Supports any network device - fully
installation of any new cabling. Thus
RJ45 to RJ45 network connection from
transparent 100BaseT Ethernet
the investment in the original cabling
end to end across the existing cabling.
• Simple to install - no IP address or
(usually around 30% of any system
This HIGHWIRE to HIGHWIRE
other setup required
installation cost) can be retained and
connection instantly operates as a
• Full-speed over 300m (1000ft)
exploited for new-generation networked
full-duplex 100BaseT Ethernet
of RG-59
CCTV camera systems. HIGHWIRE is
connection and is completely
• Compact - fits inside camera housings
especially suited to mega-pixel IP camera
transparent to any network device.
• Low power - uses camera supply
applications or multiple IP cameras as it
HIGHWIRE has no MAC address or IP
• Rack-mount option for control room end
supports high data rates.
address and requires no set-up at all.
NETWORK SWITCH
CAMERA
NVR
CO-AXIAL VIDEO CABLE
Application
external camera housing. The HIGHWIRE
Universal Application
In the application above, a high-resolution
link runs across the existing installed
Although designed for IP video, the
mega-pixel IP camera replaces a standard
75ohm co-axial video cable, and the
HIGHWIRE connection is a universal
analogue CCTV video camera. The IP
rest of the network is connected at the
100Base-T network link that can be
camera’s standard Ethernet TCP/IP
other end (usually, but not necessarily, a
used for any application. Any legacy
connection is linked to a HIGHWIRE
control or equipment room). One, several
coaxial cable can be used, or new coaxial
device with a short CAT5 patch cable
or many such links may feed into the
cable can be installed, to deliver an
(straight through or cross-over). Both
network to an NVR. As the network link
extended network connection that is a
the camera and the HIGHWIRE are
is full speed and fully-transparent, the
rugged and low-cost alternative to fibre.
powered from the same power supply,
IP camera appears on the network as a
and both may be fitted inside a standard
completely normal IP connection.
HIGHWIRE Quad
HIGHWIRE Rack
HIGHWIRE QUAD integrates Veracity's
The HIGHWIRE accessory range
HIGHWIRE DIN Rail Mount
HIGHWIRE Ethernet over coaxial cable
includes a 19” 1U adaptor plate which
The HIGHWIRE accessory range
technology with a four-port POE switch.
allows 8 standard HIGHWIRE units to be
includes a Din Rail mounting kit.
This means that up to four IP cameras
neatly rack-mounted in a control room.
can be installed in place of an old
This is especially useful when installing
analogue video camera. Legacy coax
many HIGHWIRE channels together.
cabling can be used as the network connection, and an existing 12VDC or 24VAC supply can be converted into universal Power over Ethernet (POE) for the new IP cameras.
Applications HIGHWIRE Quad can be used to expand the numbers of cameras in an installation without running new cables. Whilst most commonly used with IP cameras, HIGHWIRE Quad can be used for any networking application such as VOIP, IP access control, wireless access points, or any combination of these.
www.veracityglobal.com
TM
Technical Specification: HIGHWIRE INTERFACE
Connector type
BNC 75ohm
Cable impedance
75ohm (RG59 or similar)
Cable length max
Up to 300m (RG59), 500m (RG11)
Data throughput max
200Mbps (total up + down).
ETHERNET INTERFACE
Connector type
RJ45
Cable type
Straight through or cross-over, auto detected
Rates supported
100BaseT / 10BaseT, full/half duplex with auto negotiation
LED INDICATORS
Green – Constant
Power OK, Full HIGHWIRE data link
Green – Blink
Power OK, no HIGHWIRE link
Green – Off
No power
Amber – Constant
Ethernet link On
Amber – Blink
Network traffic
POWER SUPPLY
Connector type
Screw terminals with detachable plug
Power supply type
IEC Class II isolated only
Operating voltage
8-57V DC or 20-28V AC (type & polarity auto detected)
Supply current
120mA (12V), 60mA (24V)
ENVIRONMENTAL
Operating temp.
-10ºC to 50ºC
Relative humidity
85% non-condensing
Grounding
Chassis should be grounded and is connected to the BNC shield.
Dimensions
L 104mm (83mm excl. conns.) x W 54mm x H 23mm
Weight
110g
CE, FCC, RoHS
Compliance
HIGHWIRE PRODUCT CODES
VHW-HW
HIGHWIRE Ethernet over video cable converter
VPSU-12V-U
12V DC power supply (normally not required)
VHW-WMB
Wall mounting bracket (1 HIGHWIRE unit)
VHW-1U
Rackmount kit (Bracket for 8 units in 1U high)
VHW-RMPSU-UK
Power Supply for rackmount kit (8 units)
© Veracity UK Ltd 2012 V2.0 UK
Veracity USA Inc. 65 Harristown Rd Suite 207 Glen Rock NJ 07452 USA Tel: 1-800-679-1590 Fax: 1-800-679-0714 www.veracityglobal.com
[email protected]
Veracity UK Ltd Prestwick International Aerospace Park 4 Dow Road, Prestwick KA9 2TU UK Tel +44 (0) 1292 264967 Fax +44 (0) 845 582 1081 www.veracityglobal.com
[email protected]
