Homelite Super Xl 925 Ut-10415-a

Transcript

Super XL 925 Chain Saw UT-10415-A Carburetor Chamber Page 1 of 15 Super XL 925 Chain Saw UT-10415-A Carburetor Chamber Ref # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 Part Number 63370A 63166A 63371B 65483 A674601 82174 82173 67540 A69812A 69751 83046 82179 63266A 58348 A67639 A694142 58319A 69880 80821 A67101A 583921 70189 95671 58405 58409 65745 65719 86324 A68429 64862 A68025D 68445 68767 68768 80560 A69045 59064 68046 65718B 63622 A5783416 59074 74388 59293 633435 80568 80891 80676 63779C 637781 800232 656601 A65705 80571 81126 65357 655131 A65682 Page 2 of 15 Qty 1 4 1 1 1 2 1 1 1 1 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 2 1 4 1 1 1 1 1 4 2 1 1 1 Description RETAINER- Reed valve VALVE- Reed SEAT- Reed valve GASKET- Reed valve seat MANIFOLD- Intake SCREW- Pan hd., 8-32 x 1 1/4 SCREW- Pan hd., 8-32 x 1 GASKET- Carburetor CARBURETOR GROMMET- Hi-Lo WASHER- Lock #10 SCREW- Hex hd. 10-32 x 1 7/8 ROD- Throttle BOOT- Throttle rod NUT- Cover mounting COVER- Air filter element RING- Retaining FILTER ELEMENT- Air SCREW- Hex hd. 12-24 x 1/2 BRACKET- Air filter GASKET- Mounting nut DEFLECTOR- Air PIN- Throttle latch SPRING- Throttle latch RING- Retaining TRIGGER- Throttle PIN- Throttle latch adjusting PIN- Cotter ROD- Choke GROMMET HANDLE- Throttle BUSHING (not shown) GRIP- Throttle handle GRIP- Throttle handle cover SCREW- Pan hd. 8-32 x 1/2 COVER- Throttle handle BUSHING- Nylon (not shown) GROMMET- Fuel line LINE- Fuel BUTTON- Oil pump plunger PLUNGER- Oil pump "O" RING- Shaft "O" RING- Plunger SPRING- Compression BODY- Oil pump SCREW- Hex hd. 3-32 x 7/8 SCREW- Hex hd. 12-24 x 7/8 SCREW- Hex hd. 12-24 x 5/8 GASKET- Throttle handle GASKET- Cylinder (Fig 2) SCREW- Fil. hd. 8-32 x 5/8 CLAMP- Oil line LINE- Oil (intake) SCREW- Pan hd. 6-32 x 3/8 NUT- Lock 6-32 GROMMET- Oil line CLAMP- Oil line LINE- Oil (discharge) Super XL 925 Chain Saw UT-10415-A Carburetor Chamber Ref # 57 58 Part Number A65502 25527 A65515 25527 59022 Page 3 of 15 Qty 1 1 1 1 1 Description VALVE- Check BALL- (not shown) VALVE- Check BALL- (not shown) SPRING- (not shown) Super XL 925 Chain Saw UT-10415-A Engine Internals Page 4 of 15 Super XL 925 Chain Saw UT-10415-A Engine Internals Ref # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 Part Number A69467 64742 69452 A69658A 69638 69919 68010 75078 671683 A69056 58190S 58319A 70306 59705 A65284B 69834 69451 68750 A69500A 69451 69454 69501 69502 69503 82256 65593A A69923 64083 67080 655971 80605 63367 A68023B 65144 65143 82358 95725 671532 63621 82147 55871 67159 58138 63115 28097 67158 12282A A64715 65357 93039 81204 A68265A 80919 64102A 59736 59926 59675 82248 Page 5 of 15 Qty 1 2 2 1 1 2 2 1 1 1 1 1 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 6 8 1 1 1 4 1 1 1 1 2 1 1 1 1 1 1 2 1 1 1 1 3 Description PISTON & PIN RING- Piston pin retaining PISTON RING ROD- Connecting BEARING- Needle SCREW- Soc hd. 8-32 x 9/16 WASHER- Thrust KEY- Woodruff CRANKSHAFT BEARING- Needle (set of 28) BEARING- Ball RING- Retaining SCREW- Bearing retaining WASHER- Lock CAP- Oil filler GASKET- Oil cap VALVE- Check duck bill (not shown) RETAINER CAP- Fuel filler VALVE- Check (oval duckbill) FILTER- Filler cap GASKET- Fuel cap CHAIN- Bead RETAINER SCREW- Pan hd., plastite 6 x 1/4 LINE- Fuel FILTER- Fuel FILTER- Felt CONNECTOR- Fuel line CLAMP- Fuel line SCREW- Pan hd. 6-32 x 5/16 SCREW- Guide bar adjusting CRANKCASE GASKET- Check valve (not shown) CAP- Check valve (not shown) SCREW- Fil. hd., 8-32 x 5/8 SCREW- Fil. hd., 8-32 x 2 3/16 COVER- Fuel tank PIN- Dowel SCREW- Fil. hd. 8-32 x 1 3/4 STUD GASKET- Fuel tank WASHER CAP- Oil pump PLUG- Pipe BOLT- Guide bar SEAL SHIELD- Sawdust GROMMET- Oil line PIN- Guide bar adjusting NUT- Gripco PUMP- Automatic oil SCREW- Pan hd. 4-40 x 1/4 SCREW- Cam GASKET- Cam screw SEAL- Felt WORM- Gear SCREW- Fil hd. 8-32 x 3/4 Super XL 925 Chain Saw UT-10415-A Engine Internals Ref # 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 76 77 78 79 80 81 Part Number 31734 65696 A65682 A64293 64356 65695 63452A 58406 63751 A69864C 82280 95885 69842 A698361 69843 69844 A93900A A698381 69839 A42206A 637781 80402 93561S 63547S 69027S 810652 83009 A94119 A93900A 78098 Page 6 of 15 Qty 1 1 1 2 2 1 1 1 1 1 2 1 1 1 2 1 1 1 1 1 1 3 1 1 1 4 4 1 1 1 Description CONNECTOR- Elbow FITTING- Tube LINE- Oil (discharge) FILTER- Oil LINE- Oil pick-up CONNECTOR- Oil filter TUBE- Oil line "O" RING GASKET- Oil line tube MUFFLER- Downdraft (complete) SCREW- Hex hd. cap 1/4-20 x 3 SCREW- Hex hd. 1/4-20 x 2 3/8 SHIELD- muffler CAP- Muffler (SXL-925) SUPPORT- Muffler (long) SUPPORT- Muffler (short) SCREEN- Spark arrestor BODY- Muffler PLATE- Muffler body CYLINDER- 2 1/16" bore GASKET- Cylinder SCREW Hex hd. cap 1/4-20 x 5/8 (not shown) SPARK PLUG CJ-6Y Champion (after Lot #C-246) SPARK PLUG- C-J6 Champion (prior to Lot #C-246) SPARK PLUG- C-J4 Champion (opt) (colder plug) NUT- Hex 1/4-28 WASHER- Lock, 1/4 KIT- Muffler temperature ("SXL-925W") SPARK ARRESTOR GASKET- Muffler Super XL 925 Chain Saw UT-10415-A Handles & Clutch Page 7 of 15 Super XL 925 Chain Saw UT-10415-A Handles & Clutch Ref # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 Part Number A69034 82259 68765 65599 A70289A 65598A 80867 65518 65520 A63720 80867 81068 83056 A70618 70399 70400 6715614 810892 680781 63284 64129A 64124 63462 63463 A94117 A95631 93650 A94126 93811 93814A 93126 82253 93628 803612 A24921A 12940 67441 657232A 697541 63462 64124 A65990 63284 63285 64129A A94153 A784571T 680781 688981 65599 78117 687664C 80867 65598A 840651 95898 95935 96757 Page 8 of 15 Qty 1 1 1 1 1 1 2 2 2 1 2 2 2 1 1 1 1 2 1 1 1 1 1 1 1 1 1 3 1 3 3 3 1 2 1 2 2 1 6 2 1 1 1 1 1 1 1 1 1 1 2 1 2 1 1 1 1 1 Description HANDLE BAR- Flush cut (rubber cover) SCREW- Fil, hd., 1/4-20 x 1 SPACER- Handle bar PLATE- Handle bar BRACKET- Handle bar (flush cut) PLATE- Handle bar bracket SCREW- 12-24 x 3/4 GROMMET- Handle bar SCREW- Shoulder KIT- Spiked bumper SCREW- Hex hd., 12-24 x 3/4 NUT- 12-24 WASHER- Lock #12 GUIDE BAR PLATE PLATE- Guide bar (Inner) PLATE- Guide bar (outer) COVER- Drivecase NUT- Hex 3/8-16 GUARD- Chain (SXL-925W) SPROCKET- 7 spline 7T-3/8 pitch 3 shoe clutch (SXL-925W) RACE- Inner BEARING- Roller WASHER- Thrust (inner) for rim sprocket only) WASHER- Thrust (inner) (for spur sprocket & drum) DRUM 8. HUB (SXL-925W) SPROCKET & DRUM (for 3 shoe clutch) 3/8 7 tooth WASHER- Thrust SHOE- Clutch SPIDER- Clutch SPRING- Clutch SCREW- Torx SCREW- Mach pan hd. 8-32 x 3/8'' (alternate) COVER- Clutch SCREW- Hex hd., 10-32 x 1/2 (opt.) COVER- Clutch (opt.) WASHER- Belleville SPRING- Clutch (opt.) SPIDER- Clutch (opt.) SHOE Clutch (opt.) WASHER- Thrust BEARING- Roller DRUM & HUB- Rim type (opt.) SPROCKET- 3/8 pitch 7 tooth (opt.) 404 pitch 7 tooth (opt.) RACE- Inner KIT- Handle- wrap-around (SXL-925W) HANDLE BAR CHAIN GUARD (See Index #18) SPACER PLATE (see Index #4) SCREW- 1 4-20 x 1.125 BRACKET- Handle bar SCREW- 12-24 x 3/4 (see Index #7) PLATE- Handle bar bracket (see index #6) WASHER HAND GUARD WASHER WASHER Super XL 925 Chain Saw UT-10415-A Handles & Clutch Ref # 49 50 51 Part Number 95937 80945 81225 A65886 A95620 A65732 Page 9 of 15 Qty 1 1 1 1 1 1 Description SPACER SCREW- Flat hd., 12-24 x 1 NUT- Lock SPROCKET 8 DRUM 404 7 tooth SPROCKET 8 DRUM 3 8 7 tooth SPROCKET 8 DRUM 3 8 8 tooth Super XL 925 Chain Saw UT-10415-A HS-151B Carburetor Page 10 of 15 Super XL 925 Chain Saw UT-10415-A HS-151B Carburetor Ref # 1 2 3 4 5 6 7 8 9 10 Part Number 95698 95698 95698 95698 95698 95698 95698 95698 70334 69793 A69819 Page 11 of 15 Qty 1 1 1 1 1 1 1 1 1 1 1 Description Repair Kit Repair Kit Repair Kit Repair Kit Repair Kit Repair Kit Repair Kit Repair Kit Governor Valve Check Valve Kit - High altitude nozzle Super XL 925 Chain Saw UT-10415-A Starter & Ignition Page 12 of 15 Super XL 925 Chain Saw UT-10415-A Starter & Ignition Ref # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 Part Number 80676 A64504C A64421 67191 67177 64443 65830 A93875 93862 A69962B 70018A 63566 63268A 63565A A64446 94827 58763 80648 81124 83102 84010 58757E 58756 70901 653752 96801 A96798 96743 88044 A94850 A576503A 72084A1 12793A 802181 A96799 12282A 63195 A33055 A02480 82178 83022 67162 67167 A67618A 12282A 63195 67559 67166 67164A 67163 67409 80048 Page 13 of 15 Qty 4 1 1 4 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 2 2 1 1 1 2 1 1 1 1 1 1 1 1 1 1 7 7 1 1 1 1 1 1 1 1 1 1 3 Description SCREW- Hex hd. 12-24 x 5/8 HOUSING- Fan SCREEN- Fan housing STUD- Drive BUSHING- Starter rope BUSHING- Starter post BUSHING- Rewind spring ROPE- Starting WASHER GRIP- Starting rope INSERT- Rope retaining SHIELD- Spring (inner) SPRING- Rewind SHIELD- Spring (outer) PULLEY- Rewind starter LOCK- Rewind spring WASHER- Retaining SCREW- Hex hd. 10-32 x 1/2 NUT- Hex 3/8-24 WASHER- Lock 3/8 WASHER- Flat 3/8 STUD- Pawl PAWL- Starter WASHER- Lock #12 SPRING- Starter pawl ROTOR- Magneto MODULE- Ignition LEAD- High tension SCREW- Sems hex hd. LEAD- Ground SWITCH- Toggle NUT PLATE- Indicating SCREW- 1/4-20 PLATE- Back SEAL BEARING TERMINAL- Spark plug ROTOR- Magneto (prior to lot #C-246) SCREW- Pan 8-32 x 3/4 (prior to lot #C-246) WASHER- Lock #8 (prior to lot #C-246) MODULE- Ignition (prior to lot #C-246) LEAD- Transformer (prior to lot #C-246) PLATE- Back (prior to lot #C-246) SEAL BEARING- Roller "O" RING LEAD- High tension (prior to lot #C-246) COIL- Transformer (prior to lot #C-246) COIL- Core and generator (prior to lot #C-246) RING- Air flow (until lot #7045 only) SCREW- Hex cap 1/4-20 x 5/8 Super XL 925 Chain Saw UT-10415-A Tools & Accessories Page 14 of 15 Super XL 925 Chain Saw UT-10415-A Tools & Accessories Ref # A-17146 A23696A 23717A 2498201 2498202 23846-2 24304 22820-4 A-23965 84035 A-23962 24006-1 23956 23420 23955 24302 23957 A-24290 24306 23136-2A 23972 23971 A-22808 23528 24094 A-94147 80095 81009 23488-B 57084-1 A-94156-A A-93680 70361-2 70093B 12290 70346 12372-3 67911 78200-A 82258 A-12952 12955 81204 78290 A-95620 A-93682 93684 80220-2 A70790A 82335 Part Number A17146 A23696A 23717A 2498201 2498202 238462 24304 228204 A23965 84035 A23962 240061 23956 23420 23955 24302 23957 A24290 24306 231362A 23972 23971 A22808 23528 24094 A94147 80095 81009 23488B 570841 A94156A A93680 703612 70093B 12290 70346 123723 67911 78200A 82258 A12952 12955 81204 78290 A95620 A93682 93684 802202 A70790A 82335 Page 15 of 15 Qty 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Description WRENCH- Spanner (3-shoe) WRENCH- Spanner (6-shoe) PIN- Spanner clutch BIT- Driver torx (clutch plate) 1/4 shank BIT- Driver torx (clutch plate) 5/16 shank ANVIL- Bearing disassembling (back plate) BIT- Pozidriv #2 COLLAR- Bearing installation JACKSCREW- Crankshaft WASHER JACKSCREW- Bearing removal (back plate) PLATE- Crankshaft alligning PLUG- Bearing and seal installatlon (back plate) PLUG- Bearing Installatlon PLUG- Bearing Installatlon (conn. rod) PLUG- Seal Installation (back plate) PLUG- Seal Installation (crankcase) PULLER- rotor SHIM- Air gap (black) SLEEVE- Beanng and shaft installation SLEEVE- Seal Installation (crankcase) SLEEVE- Seal protection (crankcase) WRENCH- Comblnation WRENCH- Hex socket (conn. rod) WRENCH- Spark plug removal PULLER- Back plate SCREW- Hex cap (1) NUT- Hex (3) LOCTITE REEL- 250 ft. starting rope #5 KIT- Clutch conversion (3-shoe) KIT- Chain brake COVER- Drivecase SPRING WASHER BAND- Brake LEVER- Brake band PIN- Roll SCREW SCREW- Pan hd. 1/4-20 x 5/8 BRAKE- Lever w/guard SCREW NUT DECAL SPROCKET & DRUM BRACKET RETAINER SCREW- Fil hd. 8-32 x 7/8 SAFE-T-TIP (standard on units) SCREW