Transcript
INSTALLATION INSTRUCTIONS
MSP-DCCKTP225
MSP-DCCKTP445
MSP-DCCKTP225U MSP-DCCKTP445U
Horizontal Table Stands Spanish Product Description German Product Description Portuguese Product Description Italian Product Description Dutch Product Description French Product Description
MSP-DCCKTP SERIES
MSP-DCCKTP SERIES
Installation Instructions
DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries (collectively “Milestone”), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document. Chief® is a registered trademark of Milestone AV Technologies. All rights reserved.
IMPORTANT SAFETY INSTRUCTIONS WARNING: A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions.
WARNING: Failure to read, thoroughly understand, and follow all instructions can result in serious personal injury, damage to equipment, or voiding of factory warranty! It is the installer’s responsibility to make sure all components are properly assembled and installed using the instructions provided.
WARNING: Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment. Reinforce the structure as required before installing the component. WARNING: Exceeding the weight capacity can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the combined weight of all components attached to the MSP-DCCKTP SERIES mounts does not exceed 35 lbs (15.87 kg) per display for the single array models (MSP-DCCKTP225/U) or 20 lbs (9.07 kg) per display for the dual array models (MSP-DCCKTP445/U).
2
WARNING: Use this mounting system only for its intended use as described in these instructions. Do not use attachments not recommended by the manufacturer.
WARNING: Never operate this mounting system if it is damaged. Return the mounting system to a service center for examination and repair.
WARNING: Do not use this product outdoors.
--SAVE THESE INSTRUCTIONS--
Installation Instructions
MSP-DCCKTP SERIES
DIMENSIONS MSP-DCCKTP225 17.24 437.8
2.00 50.8
15.47 393.0
12.50 317.5
31.04 788.4 34.43 874.6
30.73 780.5 2.95 75.0
3.94 100.0
14.25 362.0
13.25 336.6
MSP-DCCKTP445
17.24 437.8 2.00 50.8
15.47 393.0
12.50 317.5
31.04 788.4 34.43 874.6
30.73 780.5 2.95 75.0
3.94 100.0
28.25 717.6
27.25 692.2
12.25 311.2
IF SAME SIZE DISPLAY IS USED FOR BOTH, MAXIMUM SCREEN WIDTH OF 30.0"
3
MSP-DCCKTP SERIES
Installation Instructions
DIMENSIONS (CONTINUED) 17.24 437.8
MSP-KTP225U
12.47 316.8
2.00 50.8
12.50 317.5
25.04 636.0 34.43 874.6
24.73 628.1 2.95 3.94 75.0 100.0
14.25 362.0
13.25 336.6
IF SAME SIZE DISPLAY IS USED FOR BOTH, MAXIMUM SCREEN WIDTH OF 30.0"
17.24 437.8
MSP-KTP445U
12.47 316.8
2.00 50.8
12.50 317.5
25.04 636.0 34.43 874.6
24.73 628.1 2.95 3.94 75.0 100.0
28.25 717.6
27.25 692.2
12.25 311.2
IF SAME SIZE DISPLAY IS USED FOR BOTH, MAXIMUM SCREEN WIDTH OF 30.0"
4
Installation Instructions
MSP-DCCKTP SERIES
LEGEND Tighten Fastener
Pencil Mark
Apretar elemento de fijación
Marcar con lápiz
Befestigungsteil festziehen
Stiftmarkierung
Apertar fixador
Marcar com lápis
Serrare il fissaggio
Segno a matita
Bevestiging vastdraaien
Potloodmerkteken
Serrez les fixations
Marquage au crayon
Loosen Fastener
Drill Hole
Aflojar elemento de fijación
Perforar
Befestigungsteil lösen
Bohrloch
Desapertar fixador
Fazer furo
Allentare il fissaggio
Praticare un foro
Bevestiging losdraaien
Gat boren
Desserrez les fixations
Percez un trou
Phillips Screwdriver
Adjust
Destornillador Phillips
Ajustar
Kreuzschlitzschraubendreher
Einstellen
Chave de fendas Phillips
Ajustar
Cacciavite a stella
Regolare
Kruiskopschroevendraaier
Afstellen
Tournevis à pointe cruciforme
Ajuster
Open-Ended Wrench
Remove
Llave de boca
Quitar
Gabelschlüssel
Entfernen
Chave de bocas
Remover
Chiave a punte aperte
Rimuovere
Steeksleutel
Verwijderen
Clé à fourche
Retirez
By Hand
Optional
A mano
Opcional
Von Hand
Optional
Com a mão
Opcional
A mano
Opzionale
Met de hand
Optie
À la main
En option
Hex-Head Wrench
Security Wrench
Llave de cabeza hexagonal
Llave de seguridad
Sechskantschlüssel
Sicherheitsschlüssel
Chave de cabeça sextavada
Chave de segurança
Chiave esagonale
Chiave di sicurezza
Zeskantsleutel
Veiligheidssleutel
Clé à tête hexagonale
Clé de sécurité
5
MSP-DCCKTP SERIES
Installation Instructions
TOOLS REQUIRED FOR INSTALLATION
7/32" (included) 5/32" (included)
#2 3/4” (19 mm)
PARTS
Quantities listed - (225/445 models)
B (1/2) [Array clamp]
C (2/4) 1/4-20 x 3/4”
F (1/1) 5/32”
D (2/4) 1/4”
E (1/1) 7/32”
G (1/1) 3/8-16 x 1"
A (1/2) [Array assembly] H (8/16) M4x12mm
J (8/16) M4x20mm
K (8/16) M4x30mm
L (8/16) 3/8”
Q (1/1) [Pipe cap]
N (1/1) [Base]
P (1/1) [Pole]
6
R (1/1) [Cable management cover]
M (8/16) 3/4”
Installation Instructions
MSP-DCCKTP SERIES
Assembly And Installation
Display Installation - Non-interface Models
To assemble array to pole
Attach Centris Head to Flush Mount Display
1. Assemble pole (P) to base (N) using one 3/8-16 x 1" flat head cap screw (G). (See Figure 1) (P)
(E)
CAUTION: If display uses a screw size other than those included in the kit, DO NOT use the screws provided. Using the wrong screws could result in damage to your monitor. 1. Install two M4 x 12mm Phillips pan head screws (H) into two upper mounting holes in display back. (See Figure 3)
(G)
NOTE: DO NOT fully tighten at this time. 2. Hang display on Centris head. (See Figure 4) 3. Install bottom two M4 x 12mm Phillips pan head screws (H) through Centris head mounting holes and into lower mounting holes in display back.
(N)
4. Tighten ALL four M4 x 12mm Phillips pan head screws (H). (See Figure 5)
Figure 1 2. Assemble pole clamp back (B) to array assembly (A) using two 1/4” washers (D) and two 1/4-20 x 3/4” button head cap screws (C) using a 5/32” hex key (F). (See Figure 2)
(H) x 2
3. Secure array clamp (B) to array assembly (A) and pole by tightening two 1/4-20 x 3/4” button head cap screws (C). (See Figure 2)
(P) (A) Display (D) x 2 Figure 3 Display
(B)
3
Figure 2 4. Repeat Steps 1-3 for dual array models.
(C) x 2
(A)
Centris Head
5. Add pipe cap (Q) to top of pole (P). Figure 4
7
MSP-DCCKTP SERIES
Installation Instructions
Display
Centris Head
4. Place four 3/8” or 3/4” nylon spacers (L or M) over four mounting holes in display back (See Figure 8). 5. Align Centris head mounting holes with four nylon spacers (See Figure 8). 6. Secure Centris head to display using four M4 x 20mm Phillips pan head screws (J) [if using 3/8” (L) spacers], or four M4 x 30mm Phillips pan head screws (K) [if using 3/4” (M) spacers] (See Figure 8).
(A)
3
(J or K)
(H) x 2
Centris Head (L or M)
Figure 5 Attach Centris Head to Recessed Mount Display 1. Uninstall end lock using the 5/32” hex key (F). (See Figure 6) 2. Remove Centris head from array rail (A).
Display
Centris Head Square Nut Figure 8
7. Slide display with Centris bracket onto array rail (A). (See Figure 9) NOTE: Repeat previous steps for each additional display. (A)
End Lock
Display with Centris Bracket Figure 6
(A)
(A)
Centris Head Figure 7 3. Place display face down on a clean dry surface.
8
Figure 9
Installation Instructions
MSP-DCCKTP SERIES
8. Reinstall end locks into mounting rail using the 5/32” hex key (F) (See Figure 10).
3.
Slide base of monitor towards mount until lower tabs secure display to mount. An audible “click” should be heard. (See Figure 12)
(side view) (A) End Lock
Centris Head
End Lock Retaining Screw
3
Figure 10
Display Installation - Interface Models IMPORTANT ! : Interface brackets are designed specifically for Dell’s quick-connect style monitors. Do not attempt to install any other type of monitors to these mounts! 1.
Position monitor over mounting tabs on quick-connect bracket (A). (See Figure 11)
2.
Lower monitor onto quick-connect bracket, inserting mounting tabs into top two top mounting holes on back of monitor. (See Figure 11)
Figure 12
2
mounting tabs
Figure 11
9
MSP-DCCKTP SERIES
Display Removal - Interface Models
Installation Instructions
ADJUSTMENTS Display Adjustment
WARNING: Only remove display from mount when the display can be lifted up from the mount! DO NOT remove display unless the display is in the upright position! (See Figure 13)
The MSP-DCCKTP Series mount allows horizontal, pitch, and rotational adjustment of each display.
1.
Press quick release tab on back of display to release display from faceplate. (See Figure 13)
The MSP-DCCKTP Series mount also allows a full 360 deg. of display rotation with a maximum pitch range of 15° up and 15° down.
2.
Pull bottom of display away from faceplate. (See Figure 13)
Display Horizontal Position Adjustment
3.
Lift display up from faceplate. (See Figure 13) and (See Figure 14)
To adjust display horizontal position: 1. Loosen Centris bracket rear adjustment knob (See Figure 15).
1 quick release tab
2. Slide Centris bracket with display left or right until properly positioned on array rail. 3. Tighten Centris bracket rear adjustment knob.
3 Horizontal Adjustment Knob
Figure 13
Figure 15
3
2
Figure 14
10
Installation Instructions
MSP-DCCKTP SERIES
Display Pitch and Roll Adjustment To adjust display pitch or roll position: 1. Loosen Centris bracket front adjustment knob. (See Figure 16) 2. Tilt display up or down, or adjust display roll left or right until properly positioned. 3. Tighten Centris bracket front adjustment knob.
Pitch/Roll Adjustment Knob
Figure 16
CABLE MANAGEMENT The MSP-DCCKTP Series mount includes cable management features used to properly route and secure display cables. To use the cable management features: 1. Connect cables to display. 2. Route cables through cable clips on array rail. 3. Route cables down pole and away from mount and secure to pole using sheath (R).
Cable Clips
(R)
Figure 17
11
MSP-DCCKTP SERIES
Installation Instructions
USA/International
Europe Chief, a products division of Milestone AV Technologies 8800-002651 Rev00 2014 Milestone AV Technologies www.chiefmfg.com 08/14
Asia Pacific
A P F A P F A
6436 City West Parkway, Eden Prairie, MN 55344 800.582.6480 / 952.225.6000 877.894.6918 / 952.894.6918 Franklinstraat 14, 6003 DK Weert, Netherlands +31 (0) 495 580 852 +31 (0) 495 580 845 Office No. 918 on 9/F, Shatin Galleria 18-24 Shan Mei Street Fotan, Shatin, Hong Kong P 852 2145 4099 F 852 2145 4477
