Transcript
Manual Version: 6P103-20130125
BOM: 3123A0F9
Part number: 5998-2243
HP 7500 NetStream Monitoring Module 1 Appearance The silkscreen LSQ1NSMSC0 is printed at the upper right corner of the front panel, and it identifies the module. Figure 1 Appearance of the LSQ1NSMSC0
2 Specifications The LSQ1NSMSC0 module provides one console port, one CF card slot, two USB interfaces, two 10/100/1000BASE-T management Ethernet copper interfaces, and two management Gigabit combo interfaces. Figure 2 Front panel of the LSQ1NSMSC0
(1) CF card eject button
(2) CF card slot (CF CARD)
(3) CF LED (CFS)
(4) Console port (CONSOLE)
(5) USB interface 1 (reserved)
(6) USB interface 2 (reserved)
(7) Management Ethernet interface 1 (10/100/1000BASE-T)
(8) Management Ethernet interface 2 (10/100/1000BASE-T)
(9) Management Ethernet interface 1 LED (LINK)
(10) Management Ethernet interface 1 LED (ACT)
(11) Management Ethernet interface 2 LED (LINK)
(12) Management Ethernet interface 2 LED (ACT)
(13) Management interface 3 (Electrical port of combo interface 10/100/1000BASE-T)
(14) Management interface 4 (Electrical port of combo interface 10/100/1000BASE-T)
(15) Management interface 3 (Optical port of combo interface 1000BASE-X)
i
Manual Version: 6P103-20130125
BOM: 3123A0F9
Part number: 5998-2243
(16) Management interface 4 (Optical port of combo interface 1000BASE-X)
(17) Management interface 3 LED (LINK)
(18) Management interface 3 LED (ACT)
(19) Management interface 4 LED (LINK)
(20) Management interface 4 LED (ACT)
(21) Ejector lever
(22) Captive screw
Table 1 Description of the LEDs on the LSQ1NSMSC0 Silkscreen
CFS
Color
Green
LINK
Green
ACT
Yellow
Status
Description
Off
No CF card is present or the CF card is not recognizable.
On
A CF card is in position and has passed the power-on self test.
Blinking
The system is accessing the CF card. In this state, do not remove the CF card.
Off
No link is present.
On
A link is present.
Off
No data is being sent and received.
Blinking
Data is being sent and received.
Table 2 LSQ1NSMSC0 specifications Item
Specification One console port Two USB interfaces (reserved) Two 10/100/1000BASE-T management Ethernet electrical interfaces
Interface
Two Gigabit combo interfaces, supporting flexible switching between optical and electric interfaces. Only one type of interface(s), optical or electrical, can work at a time. Supported interface types are as follows:
• 10/100/1000BASE-T electrical interface • 1000BASE-X SFP optical interface Interface transmission speed
• Console port—9600 bps to 115200 bps (default: 9600 bps) • 10/100/1000BASE-T electrical interface—10/100/1000 Mbps, half/full duplex • 1000BASE-X SFP optical interface—1000 Mbps, full duplex
Connector
RJ-45 (for electrical interface) or SFP/LC (for optical interface)
• Console port—Asynchronous serial cable with maximum transmission distance of Cable and maximum transmission distance
15 m (49.21 ft)
• 10/100/1000BASE-T electrical interface—Category 5 or above UTP with maximum transmission distance of 100 m (328.08 ft)
• 1000BASE-X SFP optical interface—For more information, see Table 3 CF card and slot Applied to
One CF card slot, 256 MB by default for the external CF card 256 MB, 512 MB, or 1 GB for an optional external CF card HP 7500 series switches
ii
Manual Version: 6P103-20130125
BOM: 3123A0F9
Part number: 5998-2243
Table 3 1000BASE-X SFP interface specifications Item
Specification
Connector
SFP/LC
Interface standards
802.3, 802.3u, and 802.3ab
Type
Short-haul multi-mode (850 nm) Optical interface module
Mid-haul single-mode (1310 nm) Optical interface module
Long-haul (1310 nm) Optical interface module
Long-haul (1550 nm) Optical interface module
Extra-long-ha ul (1550 nm) Optical interface module
Min
–9.5dBm
–9dBm
–2dBm
–4dBm
–4dBm
Max
0dBm
–3dBm
5dBm
1dBm
2dBm
Reception sensitivity
–17dBm
–20dBm
–23dBm
–21dBm
–22dBm
Central wavelength
850nm
1310nm
1310nm
1550nm
1550nm
Fiber type
62.5/125μm MM fiber
9/125μm SM fiber
9/125μm SM fiber
9/125μm SM fiber
9/125μm SM fiber
Max transmission distance
0.55 km (0.34 miles)
10 km (6.21 miles)
40 km (24.86 miles)
40 km (24.86 miles)
70 km (43.50 miles)
Optical transmit power
3 Installing and removing the LSQ1NSMSC0 WARNING! • Wear an ESD-preventive wrist strap and ESD-preventive gloves before installing or removing the module, and make sure that the ESD-preventive wrist strap is properly grounded. • Avoid touching any components on the PCB and hold the PCB by its edge when installing and removing the module. NOTE: The LSQ1NSMSC0 is hot swappable. That is, you can remove the module from a switch when the switch is powered on.
3.1 Installing the LSQ1NSMSC0 1.
Locate the slot where you will install the LSQ1NSMSC0, and remove the blank panel from the position. This manual describes installing the LSQ1NSMSC0 to slot 2.
2.
Push the module (with the components facing on) into the slot along the guide rails until the positioning hole of the module is seated onto the positioning pin on the backplane. Push the ejector levers inward to lock the module in place.
3.
Fasten the captive screws on the module with a Philips screwdriver.
iii
Manual Version: 6P103-20130125
BOM: 3123A0F9
Part number: 5998-2243
Figure 3 Insert the LSQ1NSMSC0
(1) Push the module into the slot along the guide rails until the positioning hole of the module is seated onto the positioning pin on the backplane. (2) Push the ejector levers inward to lock the module in place.
3.2 Removing the LSQ1NSMSC0 1.
Loosen the captive screws on the module with a Philips screwdriver until all spring pressure is released.
2.
Hold the ejector levers of the module and push them outward. Gently pull the module out of the slot along the guide rails.
3.
Put the removed module on an antistatic workbench with the PCB side facing upward or place it in an antistatic bag. If you do not install a new LSQ1NSMSC0 in the slot, install a blank panel to prevent dust from entering the chassis and ensure normal ventilation in the switch.
4 Logging in to the LSQ1NSMSC0 Before logging in to the LSQ1NSMSC0, configure the AUX user interface of the module.
iv
Manual Version: 6P103-20130125
BOM: 3123A0F9
Part number: 5998-2243
Table 4 Configure the AUX user interface of the LSQ1NSMSC0 Commands
Description
system-view
Available in user view.
user-interface aux first-number [ last-number ]
Enter one or more AUX user interface views Specify the none authentication mode
authentication-mode none
By default, password authentication is performed for users that log in through the AUX user interface. Configure the user privilege level for login users
user privilege level level
By default, the default command level is 0 for the AUX user interface. HP recommends you to set the level to 3.
After configuring the AUX user interface, use the oap connect command to log in to the module from the switch to enter the command line interface (CLI) of the module and manage the module. To return to the CLI of the switch, press Ctrl+K. Table 5 Redirect from the switch to the LSQ1NSMSC0 Command
Description
When the switch works in standalone mode:
Available in user view
oap connect slot slot-number When the switch works in IRF mode: oap connect chassis chassis-number slot slot-number
Available in user view
NOTE: Besides the login method mentioned in this manual, you can also log in to the LSQ1NSMSC0 through Telnet, or the console port on the module. For more information, see HP NetStream Monitoring Module Configuration Guide.
5 Upgrading the LSQ1NSMSC0 The LSQ1NSMSC0 supports software upgrade through the console port and a management Ethernet interface on the module. For more information about how to upgrade the LSQ1NSMSC0, see HP Security Modules Software Upgrade Guide. The LSQ1NSMSC0 adopts independent boot and application programs, so the boot menu is different from the switch. To upgrade the application program of the LSQ1NSMSC0, use one of the following ways: 1.
Remote upgrade at the CLI
•
Use the FTP/TFTP protocol through the management Ethernet interface of the LSQ1NSMSC0.
2.
Local upgrade through the boot menu
•
Use the XMODEM protocol through the console port of the LSQ1NSMSC0
•
Use the FTP/TFTP protocol through the management Ethernet interface of the LSQ1NSMSC0.
v
Manual Version: 6P103-20130125
BOM: 3123A0F9
Part number: 5998-2243
NOTE: • The LSQ1NSMSC0 does not support software upgrade through a switching and routing processing unit (SRPU) of the switch. • Using the XMODEM protocol to upgrade the module is relatively slow. To reduce the upgrade time, HP recommends you to upgrade the module through the FTP/TFTP protocol. • When you upgrade the LSQ1NSMSC0 through the management Ethernet interface, make sure that the module and the FTP or TFTP server can reach each other.
6 Obtaining documentation For module installation, see the HP 7500 Switch Series Installation Guide. For software upgrade, see the HP Security Modules Software Upgrade Guide. To find related documents, browse to the Manuals page of the HP Business Support Center website: http://www.hp.com/support/manuals
© Copyright 2013 Hewlett-Packard Development Company, L.P. The information in this document is subject to change without notice.
5998-2243
vi
