Transcript
HRA 3000 MONO CLOCK RADIO MUSIC BOX WITH USB/SD FOR MP3 PLAYBACK
INSTRUCTION MANUAL
E-1
LOCATION OF CONTROLS 1) 2) 3) 4) 5) 6) 7) 8) 9) 10) 11) 12) 13) 14) 15) 16) 17) 18) 19) 20) 21) 22) 23) 24) 25) 26) 27)
SNOOZE/DISPLAY BUTTON DIMMER CONTROL BUTTON SLEEP FUNCTION BUTTON STANDBY LED INDICATOR SPEAKER CLOCK-ADJUST/ID3 BUTTON PLAY MODE BUTTON PRE-SET EQ BUTTON SD/MMC CARD SLOT ALARM 2 ON/OFF BUTTON ALARM 1 ON/OFF BUTTON FOLDER UP BUTTON TRACK SKIP DOWN BUTTON LCD DISPLAY TRACK SKIP UP BUTTON BAND / STOP BUTTON POWER ON/STANDBY BUTTON FUNCTIONS BUTTON BUTTON PLAY/PAUSE VOLUME UP + BUTTON TUNING KNOB VOLUME DOWN – BUTTON STEREO HEADPHONE JACK USB SOCKET FM WIRE ANTENNA AUXILIARY INPUT JACK AC POWER CORD
CAUTION: USAGE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. THIS UNIT SHOULD NOT BE ADJUSTED OR REPAIRED BY ANYONE EXCEPT QUALIFIED SERVICE PERSONNEL.
PRECAUTIONS FOR USE INSTALLATION • • •
UNPACK ALL PARTS AND REMOVE PROTECTIVE MATERIAL. DO NOT CONNECT THE UNIT TO THE MAINS BEFORE CHECKING THE MAIN VOLTAGE AND BEFORE ALL OTHER CONNECTIONS HAVE BEEN MADE. DO NOT COVER ANY VENTS AND MAKE SURE THAT THERE IS A SPACE OF SEVERAL CENTIMETERS AT THE BACK OF THE UNIT FOR VENTILATION.
CONNECTION 1. 2. 3.
CONNECT THE POWER CORD (27) TO AC OUTLET WHEN YOU FIRST PLUG THE UNIT INTO THE MAINS, THE UNIT WILL GO INTO STANDBY MODE AND THE STANDBY LED INDICATOR (4) WILL LIGHT UP, THE CLOCK AT LCD DISPLAY WILL SHOW “ 00 : 00 ”. TURN ON THE POWER (17), IF THE LCD DISPLAY IS ON WITH BACKLIGHTING, IT MEANS THE POWER SUPPLY IS NORMAL. NOW YOUR SYSTEM IS READY TO PLAY THE MUSIC.
SETTING THE CLOCK 1. 2. 3. 4.
¾
SET UNIT AT STANDBY MODE. PRESS THE “ CLK-ADJ/ID3 ” BUTTON (6) TO ENTER CLOCK ADJUST MODE, THENPRESS OR BUTTON (13,15) TO SELECT THE APPROPIATE AREA HOUR (12H/24H) OR PRESS “ CLK-ADJ/ID3 ” BUTTON (6) AGAIN, THE FIRST SECOND DIGIT OF “00” IS FLASHING. PRESS BUTTON (13,15) TO SET THE CORRECT HOUR. PRESS ” CLK-ADJ/ID3 ” BUTTON (6)TO STORE THE CORRECT HOUR. OR BUTTON (13,15) TO SET THE THE THIRD FOURTH DIGIT OF “00” IS FLASHING, PRESS THE CORRECT MINUTES. THEN PRESS “CLK-ADJ/ID3” (6) TO STORE THE CORRECT MINUTE.
THE PRE-SET TIME WILL BE RE-SET COMPLETELY IF DIS-CONNECTING THE MAIN POWER SUPPLY. YOU ARE RECOMMENDED TO SWITCH THE SYSTEM INTO STANDBY MODE FOR CONVENIENCE USAGE. E-2
LISTENING TO RADIO OPERATION 1. 2. 3.
PRESS THE FUNCTION BUTTON (18) TO SELECT TUNER MODE. / BAND ” BUTTON (16) TO SELECT DESIRED BAND (AM OR FM).TURN THE TUNING KNOB (21) PRESS “ TO SET THE STATION FREQUENCY AS DESIRED. ADJUST VOLUME CONTROL (20,22) FOR THE DESIRED VOLUME LEVEL.
HINTS FOR BEST RECEPTION:-
AM : THE RECEIVER HAS A BUILT-IN AM BAR ANTENNA. IF AM RECEPTION IS WEAK, SLIGHTLY ROTATE OR RE-POSITIONING OF THE UNIT WILL USUALLY IMPROVE THE AM RECEPTION. FM : THE RECEIVER HAS A BUILT-IN FM WIRE ANTENNA HANGING AT THE REAR CABINET. THIS WIRE SHOULD BE TOTALLY UNRAVELED AND EXTENDED FOR BEST RECEPTION.
PLAYBACK OF MP3/WMA SONG VIA USB STORAGE MEDIA OR MEMORY CARD CONNECTING THE SYSTEM IS ABLE TO DECODE AND PLAYBACK ALL MP3 FILE WHICH STORED IN THE MEMORY MEDIA WITH USB CONNECTING PORT, MULTI- MEDIA CARD (MMC) OR SECURE DIGITAL (SD) MEMORY CARD. 1. 2.
z
3.
PRESS THE FUNCITON BUTTON (18) & SELECT EITHER “ USB “ OR “ CARD “ MODE PLUG-IN THE USB PLUG WITH THE FACE UP & MAKE SURE IT GOING INTO COMPLETELY OR INSERT THE MEMORY CARD (SD/MMC) IN THE DIRECTION OF THE ARROW AS SHOWN IN THE LABEL ON THE UNDERSIDE OF THE MEMORY CARD SLOT COVER. INSERT STRAIGHT WITHOUT BENDING. CONNECTING THE USB / MEMORY CARD (SD/MMC) UPSIDE DOWN OR BACKWARDS COULD DAMAGE THE AUDIO SYSTEM OR THE STORAGE MEDIA (USB / MEMORY CARD). CHECK TO BE SURE THE DIRECTION IS CORRECT BEFORE CONNECTION. THE SYSTEM WILL START READING THE STORAGE MEDIA AUTOMATICALLY AFTER CONNECTING, AND LCD DISPLAY (14) WILL SHOW THE TOTAL NUMBER OF MP3/WMA FILES AND TOTAL NUMBER OF FOLDER BEING DETECTED.
REMARK -
THE SYSTEM CAN DETECT AND READ THE FILE UNDER MP3 AND WMA FORMAT ONLY THOUGH THE USB PORT/MEMORY CARD SLOT. IF CONNECT THE SYSTEM TO MP3 PLAYER VIA THE USB SOCKET, DUE TO VARIANCES IN MP3 ENCODING FORMAT, SOME MP3 PLAYER MAY NOT BE ABLE TO PLAY VIA THE USB SOCKET. IN THESE CASES PLEASE USE THE MP3 PLAYER CONNECTED TO THE AUX-IN SOCKETS AT THE REAR OF THE UNIT. USB PORT DOES NOT SUPPORT CONNECTION WITH USB EXTENSION CABLE AND IS NOT DESIGNED FOR COMMUNICATION WITH COMPUTER DIRECTLY.
OEPRATION PLAY / PAUSE MODE 1. 2.
PRESS THE “PLAY/PAUSE” BUTTON (19) TO START PLAYBACK, THE FIRST TRACK WILL START PLAYBACK. TO INTERRUPT, PRESS THE “PLAY/PAUSE” BUTTON (19) ONCE, AND THE PLAYING TIME WILL BE FREEZE & FLASHING ON THE LCD DISPLAY (14). PRESS AGAIN TO RESUME NORMAL PLAYBACK.
z
STOP MODE
1.
IF “ STOP/BAND” BUTTON (16) IS PRESSED DURING PLAY OR PAUSE MODE, SYSTEM WILL GO TO STOP MODE.
z
SKIP MODE (SKIP UP
1.
DURING PLAY OR PAUSE MODE, IF “SKIP UP ” BUTTON (15) IS PRESSED. IT WILL GO TO NEXT TRACK AND DISPLAY THE TRACK NO. AND THEN REMAIN THE PLAYBACK MODE. ” BUTTON (13) IS PRESSED. IT WILL GO BACK TO THE DURING PLAY OR PAUSE MODE, IF “SKIP DOWN BEGINNING OF THE TRACK, ORIGINAL TRACK NO. IS DISPLAY AND REMAIN PLAYBACK MODE. AFTER STEP 2, PRESS “SKIP DOWN ” BUTTON (13) AGAIN WILL GO TO THE PREVIOUS TRACK AND REMAIN PLAYBACK MODE.
2. 3.
/ SKIP DOWN
)
z
FOLDER UP
1.
PRESS “ FOLDER UP “ BUTTON (12) DURING PLAYBACK MODE, THE SYSTEM WILL START PLAYBACK THE 1ST TRACK IN THE NEXT FOLDER
E-3
z
REPEAT/RANDOM MODE
PRESS THE “ PLAY MODE” BUTTON (7) BEFORE OR DURING PLAYBACK, A SINGLE TRACK, SINGLE FLODER OR ALL THE TRACKS CAN BE REPEATED. EACH PRESS SWITCH THE REPEAT/RANDOM MODE AS FOLLOW:(1) REPEAT ALL TRACK
(2) REPEAT 1 TRACK
REPEAT MODE REPEAT ALL TRACK REPEAT SINGLE TRACKS REPEAT CURRENT FOLDER RANDOM
(3) REPEAT FOLDER
(4) RANDOM
REPEAT INDICATOR ON LCD DISPLAY ALL
RAN.
REMOVING OF USB / MEMORY CARD TO REMOVE THE USB / MEMORY CARD, TURN OFF THE POWER OR SWITCH THE FUNCTION MODE TO EITHER AUX OR TUNER FIRST. FOR USB PORT – UN-PLUG IT BY PULLING OUT THE USB SOCKET DIRECTLY, FOR MEMORY CARD – PRESS THE MEMORY CARD INWARD & THEN RELEASE, NOW THE CARD BEING PARTIALLY EJECT AND YOU CAN REMOVE IT BY HAND.
SLEEP / ALARM CLOCK SET UP A. SLEEP SETTING 1. 2. 3. 4.
B.
PRESS “SLEEP” BUTTON (3) AND “ SLEEP ” INDICATOR SHOWN ON THE LCD (14). KEEP PRESSING THE BUTTON TO ADJUST THE SLEEP TIMER IN THE ORDER OF 90 > 80 >70….10 MINUTES. SYSTEM WILL STOP AND GOTO STANDBY MODE AUTOMATICALLY AFTER THE SELECTED TIMING. TO CANCEL THE SLEEP MODE, PRESS “SLEEP” BUTTON UNTIL THE “SLEEP” INDICATOR DISAPPEAR ON LCD DISPLAY.
ALARM CLOCK SETTING
THIS FUNCTION ALLOWS THE SYSTEM TO TURN ON AUTOMATICALLY AND WAKE YOU UP BY MODE OF TUNER / CARD / USB / BUZZER SOUND RESPECTIVELY FIRST, PRESS AND HOLD THE “ ALARM 1 “ BUTTON (11) TO ENTER SETTING MODE.:-1)
WAKE UP TIME :
PRESS THE SKIP UP OR SKIP DOWN BUTTON (13,15) TO SET THE HOUR AND THEN PRESS AGAIN “ ALARM 1 ” BUTTON (11) TO SET THE MINUTES.
2) WAKE UP MODE :
PRESS THE “ ALARM 1 “ BUTTON (11) & THEN SKIP UP OR SKIP DOWN BUTTON (13,15) TO SELECT THE WAKE UP MODE FROM BUZZER / USB / CARD/ TUNER RESPECTIVELY.
OR SKIP DOWN BUTTON 3) VOLUME LEVEL : PRESS THE “ ALARM 1 “ BUTTON (11) & THEN SKIP UP (13,15) TO SELECT THE DESIRE VOLUME LEVEL. THEN PRESS AGAIN “ ALARAM 1 ” BUTTON TO COMPLETE THE SETTING
z ACTIVE/DE-ACTIVE TIMER FUNCTION 1. 2.
PRESS THE “ALARM 1” BUTTON (11) TO ACTIVE THE ALARM FUNCTION. THE TIMER INDICATOR “ ” IS SHOWN ON LCD DISPLAY (14). TO CANCEL ALARM FUNCTION BY PRESS AGAIN “ ALARM 1” BUTTON (11)UNTIL THE TIMER INDICATOR “
” DISAPPEAR.
REMARK:A)
THE SYSTEM PROVIDE DUAL ALARM SETTING “ ALARM 2 ” , YOU CAN PRESET ANOTHER WAKE UP TIME INDIVIDUALLY BY USING “ ALARM 2 “ BUTTON (10). B) IF THERE IS NO USB STICK OR SD/MMC CARD BEING DETECTED AFTER SETTING BY ALARM WAKE UP MODE. THE SYSTEM WILL DEFULT TO “ BUZZER ” SOUND FOR WAKE UP MODE AUTOMATICALLY. C) FOR TUNER WAKE UP, THE SYSTEM WILL PRESET AT THE LATEST RADIO FRQUENCY BEING LISTENED BEFORE SWITCHING OFF.
E-4
z
SNOOZE FUNCTION
PRESS ONCE TO TERMINATE THE ALARM MODE TEMPORARILY, AND SYSTEM WILL RE-START AGAIN AFTER 10 MINUTES ON EACH PRESS. TO CANCEL THE ALARM MODE, PRESS THE POWER OFF BUTTON (17) WHILE SYSTEM IS ON.
MORE FEATURES DIMMER CONROL PRESS THE DIMMER CONTROL BUTTON (2) TO SELECT 4 LEVEL FOR LCD BACKLIGHT FROM BRIGHTNESS > NORMAL > DIM MODE > BACKLIGHT OFF REPEATLY.
PRE-SET EQ FUNCTION THIS UNIT PROVIDES 5 DIFFERENCES SOUND MODE TO ENHANCE YOUR LISTENING EXPERIENCE. YOU CAN SELECT THE DESIRED EFFECT BY PRESSING THE “ PRESET EQ” BUTTON (8) REPEATEDLY AT FOLLOWING SEQUENCE:-
FLAT
JAZZ
ROCK
POP
CLASSIC
DISPLAY FUNCTION FOR CONVERIENCE USAGE, PRESS AND HOLD THE “ SNOOZE/DISPLAY “ BUTTON (1), THE LCD WILL DISPLAY THE CURRENT TIME DURING USB/CARD/AUX OR TUNER MODE RESPECTIVELY.
B) AUX-IN ENCODING CONNECT ANOTHER AUDIO DEVICE, E.G. (PORTABLE) CD PLAYER, MP3 PLAYER, (PORTABLE), IPOD, ETC. TO THIS SYSTEM VIA A CORD WITH 3.5MM DIA JACK PLUGS TO RCA JACK (NOT SUPPLIED). CONNECT ONE END OF THIS CORD TO THE 3.5MM DIA. HEADPHONE JACK ON THE EXTERNAL DEVICE AND THE OTHER END TO THE RCA AUX-IN JACK (26) ON THE BACK OF THE UNIT. WHEN CONNECTED IN THIS WAY IT IS POSSIBLE TO: •
PLAY BACK THE MUSIC ALREADY ON THE CONNECTED DEVICE. FOLLOW THE SAME ENCODING PROCEDURE AS DESCRIBED IN THIS MANUAL.
E-5
SPECIFICATIONS POWER SUPPLY AC :
230V ~ 50Hz
POWER CONSUMPTION
12W
STANDBY
2.5W
FREQUENCIES UKW (FM):
88 – 108 MHz
MW (AM):
540 – 1600 KHz
DESIGH AND SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
E-6
