Transcript
88509995 C Kitchen Center Dear Our Valuable Customers, Please follow our assembly instructions in every step, we guarantee that you will get the perfect merchandise. Thank you so much for purchasing our quality products.
Casual Attire For Today's Home
Thai Patent Pending Numbers 086878
PART LIST D. Middle Frame 1 pc. A. Top 1 pc.
B. Side Panel 1 pc.
G. Upper Back Stretcher 1 pc. H. Lower Back Stretcher 1 pc.
J1. Back Post 1 pc.
I. Front Rail 1 pc.
R. Back Support 2 pcs.
N. Shelf 2 pcs.
S. Side Rack 1 pc.
J2. Back Post 1 pc.
E. Middle Frame 1 pc. F. Back Panel 3 pcs.
C. Side Panel 1 pc.
L. Door 1 pc.
K. Base 1 pc.
O. Drawer 2O. pcs. Shelf 2 pcs.
T. Side Rack 1 pc.
U. Base Rack 1 pc.
M. Door 1 pc.
P. Drawer 2 pcs.
Q. Divider 1 pc.
(Knock-Down Construction, please refer to the last page of these instructions for steps to complete assembling drawers)
V. Brush Chrome Pipes 3 pcs.
W. Handle Arm 2 pcs.
X. Round Arm 1 pc.
HARDWARE LIST Head Cap Bolt 30 pcs. (+1Extra) Caster with and without lock 4 pcs.
Hex Wrench 1 pc.
Wood Screw for Side Drawer Part (Long 6 x 1” ) 16 pcs.(+1 Extra)
Machine Screw for Pull Handle 6 pcs.
Wood Plug 7 pcs. (+2 Extra)
Pull Handle 2 pcs.
Wood Screw for Bottom Drawer Part (Short 6 x ½”) 12 pcs.(+1 Extra)
Wood Screw 16 pcs. (+ 1 Extra)
Adjustable Pin 16 pcs. (+1 Extra)
Pull Handle 2 pcs.
Tools Required For Assembly : Philips screwdriver
Assembly Instructions 2/5 IMPORTANT NOTE Do not tighten up all the screws until each part is properly assembled. You should keep Hex Wrench in the safe place as you may need to tighten up the Head Cap Bolts in the future.
A G F
Head Cap Bolt
STEP 1 Attach the Lower Back Stretcher (H) to the Side Frame (B), using Head Cap Bolts.
B
F
F
I J1
H
Attach The Back Post (J1),(J2) to the Lower Back Stretcher (H) and slide the Back Panels (F) to place.
J2
C
Attach the Upper Back Stretcher (G) to the assembled unit, using Head Cap Bolts. Attach the Front Rail (I) to the Side Frame (B) with Head Cap Bolts. Attach the Side Frame (C) to the assembled unit, tighten up all Head Cap Bolts.
STEP 2 Turn the unit in Step1 upside down. Attach the Middle Frame (D) and (E) to the unit.
J A E
Head Cap Bolt
D A
Assembly Instructions 3/5 Wood Screw
STEP 3 Attach 4 Casters to the underside of the Base (K), put the 2 Casters with lock in front as you first need to keep the cart firmly in place. (See sticker in the bottom indicating front side)
K Locking Caster
Head Cap Bolt
K
STEP 4 Place the Base (K) on the unit. Tighten up all Head Cap Bolts.
STEP 5 Turn the assembled unit to back its normal position. Attach the Divider (Q) in the middle.
R Q
Head Cap Bolt
R G
W
Attach the Back Support (R) to the Upper Back Stretcher (G), using Head Cap Bolts. Attach the Handle Arm (W) to the Side Panel (C) with Head Cap Bolts. Slide the Round Arm (X) into place.
W C
A X
Assembly Instructions 4/5 Head Cap Bolt
STEP 6 Attach the Side Rack (S) to the Side Panel (B) with Head Cap Bolts.
B
S
Attach the Brush Chrome Pipes(V) and the Base Rack (U) to the pre-drilled holes of the Side Rack (S).
U
T
Attach the Side Rack (T) to the Side Panel (B).
V
STEP 7
Head Cap Bolt
A
Place the Top (A) on the unit. Tighten up the Head Cap Bolts.
STEP 8 Insert the Adjustable Pins into the Side Panels and into the Middle Frame at the desired level, then put the Shelf (N) into the place. Attach the Pull Handles to the Door (L) and (M) with Machine Screws. Attach the Door (L) and (M) to the Side Panel by sliding the door lift hinges into the side panel lift hinges. See assembly instructions for Drawers in the last page. Slide the Drawers (P) into place.
L O
A P N
O
A M
N Adjustable Pin
STEP 9 Cover all holes with Wood Plugs.
Lift hinge Assembly
Pull Handle Assembly
Assembly Instructions 5/5
Drawer A P1 P3
(Fig) 1 (Fig)1
P2
Line up Side Parts (O3) and (O4) to the Front Part (O1) and Back Part (O2). Be sure to follow the Arrow sign sticker on the parts. Using a Philips screw driver, insert 1” screws into each of the 4 pre-drilled holes in sides (O3) and (O4), then tighten half way.
P4
MAKE SURE ROLLER IS ON THE BACK
(Fig) 2 Turn the assembled drawer over and slide the Plywood Bottom Part (O5) into the grooves on Side Parts (O3) and (O4). Be sure to push the plywood all the way forward so it meets the Front Part (O1).
A P1
P4 A P5 P2
P3
A P1
P4 (Fig)2
P3 A P5
(Fig) 3 Insert the remaining (6) 1/2” screws into the pre-drilled holes in Bottom Part (O5), then tighten all screws
(Fig)3 (Fig)4
(Fig) 4 * If you are missing any of these parts, please contact our DMI Customer Service Department at 1-877-831-0319 or fax us at 1-800-755-2878.
Assemble the Pull Handles with Machine Screws on the Front Part (O1).
Unit Part List
P1. Front Part 2 pcs.
P2. Back Part 2 pcs.
P3. Side Part 2 pcs.
P4. Side Part 2 pcs.
P5. Bottom Part 2 pcs.
