Hs-ts1

Transcript

HS-TS1 HS-Series Terreon Undermount Basins ® • Bowl(s) are constructed of Terreon® or Terreon®RE Solid Surface Material • Clean, contemporary lines • Designed to maximize basin capacity • Integrate with Terreon Solid Surface counters to create a seamless look • Available in a variety of colors • Ideal for healthcare and multipurpose applications • ADA and ANSI Compliant when mounted at required dimensions Specifications Specify on model LD-3010, a prefabricated OmniDeck or as a stand alone basin with countertop material of your choice, including Terreon sheet goods (Model TSA) or other cast polymer material. HS-TS1 Square Undermount Bowl Construction Constructed of Terreon, a densified solid surface material composed of polyester resin or TerreonRE, a densified solid surface material composed of a bio-based resin and preconsumer recycled granules. Terreon and TerreonRE are resistant to chemicals, HS-TS1 Dimensions stains, burns and impact. Surface damage can be easily repaired with everyday cleansers Top View or fine grit abrasives. Terreon and TerreonRE are certified to meet ANSI Z124.3, Z124.6 and ANSI/ICPA SS-1-2001. Terreon and TerreonRE are GREENGUARD® certified as low-emitting materials. Code Compliance and Certifications 15" (381mm) 7½" (190mm) ANSI Standards Terreon and TerreonRE are Home Innovation Lab Certified to meet ANSI Z124.3, Z124.6 and ANSI/ICPA SS-1-2001. 7½" (190mm) Ø 4½" (114mm) 15" (381mm) National and International Plumbing Approval Terreon undermounts are Uniform Plumbing Code (UPC), International Plumbing Code (IPC) and National Plumbing Code of Canada (NPC) approved through the International Association of Plumbing and Mechanical Officials (IAPMO). Manufactured in compliance with IGC 156, CSA B45 Series & ASME A112.18.1/CSA B125.1. Standard Height Mounting To comply with ADA, the rim height of the counter or deck, and at least one bowl, must be 34" above the finished floor and must have proper knee and toe clearances. Always review local codes for compliance. Juvenile Height Mounting The rim height of the counter or deck must be no higher than 31" above finished floor and must have proper knee and toe clearances in order to comply with ADA Accessibility Guidelines for Building and Facilities: Building Elements Designed for Children’s use; Final Rule. Always review local codes for compliance. Ø 3" (77mm) ½" (13mm) 14" (356mm) Side View Section A 5⁵⁄₈" (143mm) Section A 14" (356mm) 5" (128mm) Verify all rough-in dimensions prior to installation. Consult local and national codes. Conformity and compliance to local and national codes is the responsibility of the installer. Page 1 of 2 2/10/2015 This information is subject to change without notice. Bradley_Sink_Basin_HS-TS1 © 2015 Bradley P.O. Box 309, Menomonee Falls, WI 53052-0309 800 BRADLEY (800 272 3539) +1 262 251 6000 bradleycorp.com HS-TS1 HS-Series Terreon Undermount Basins ® Basin Mounting Method Terreon Countertop Seam Adhesive (By Others) Standard Selections (Must select one from each category) All Undermount Basins are non-cancelable and non-returnable. Will Tempered Water Be Supplied to This Unit? This question must be answered to determine bowl color options (see below).  TEMP Tempered (less than 110°F or 43°C)  NO-TEMP Not tempered Drain Assembly  D-ASSY Drain Assembly Color of Terreon Bowl Solid Colors Terreon Basin  ALP-WHT  BONE  DS-WHT Alpine White Bone Designer White  NONE None  LONDON GRAY  O-TAUPE London Gray Organic Taupe Standard Colors (tempered water required) Color Matching and Installation Considerations • Basins are to be installed by a licensed fabricator. • Proper seam, joint integrity and bowl location are the responsibility of the fabricator. • Fabricator to ensure proper seam adhesive color match between basin and counter. • Specifications with sheet and basin(s) of the same solid color will require close inspection for acceptable color match before fabrication. Bradley does not guarantee an exact color match between individual sinks and sheets of the same color. • Prefabricated product available with Bradley model LD-3010 Verify all rough-in dimensions prior to installation. Consult local and national codes. Conformity and compliance to local and national codes is the responsibility of the installer. Page 2 of 2 2/10/2015 This information is subject to change without notice. Bradley_Sink_Basin_HS-TS1  AVALANCHE†  CHAR  COBBLE  DRIFT†  DUNE†  E-GRAY  GLACIER  GRAPH  LANNON Avalanche Charcoal Gray Cobblestone Driftwood Sand Dune Empire Gray Glacier Graphite Lannonstone  MOONSTONE†  PEBBLE  PEP-WHT  POLAR†  SAND  S-CREEK  S-MIST  WHT-SAND Moonstone Pebble Beach Peppered White Polar Ice Sandtrap Stone Creek Silver Mist White Sand Designer Colors (available at an additional charge) (tempered water required) Coffee Bean  ARC-CHP  COFFEE Arctic Chip  RIVER Riverstone TerreonRE Colors (available at an additional charge) (tempered water required) Moondust  BIRCH-BARK Birch Bark  MOONDUST Oat  DUSK  OAT Dusk † This color contains large, randomly distributed chips. © 2015 Bradley P.O. Box 309, Menomonee Falls, WI 53052-0309 800 BRADLEY (800 272 3539) +1 262 251 6000 bradleycorp.com