Hush Endura

Transcript

INSTRUCTION MANUAL HUSH endura™ ® TM TANNING SYSTEM (FOR PROFESSIONAL USE ONLY) (Suitable for Continuous Use) DO NOT USE EQUIPMENT BEFORE READING THIS MANUAL The Hush Endura™ sound level is: 58db DO NOT USE EQUIPMENT BEFORE READING THIS MANUAL DO NOT USE EQUIPMENT BEFORE READING THIS MANUAL This manual contains important warnings and instructions. important warnings and instructions. PleaseThis readmanual these contains instructions carefully and keep for your reference. Please fill out the warranty card at the back to obtain warranty. Please read these instructions carefully and keep for your reference. ©2017 Solaire Pty Ltd ©2012 Solaire Pty Ltd Unit 5, 32 Essington Street, Grovedale, 3216, Australia. email: [email protected] Ph: 1300 650 079 Ph: 1300 650 079 www.solaire.com.au International: +61 (3) 5245 8367 www.solaire.com.au Unit 5, 32 Essington Street, Grovedale, 3216 email: [email protected] 1 Table of Contents 1. General Safety Information: ........................................................................................................ 4 2. Set up and operate your Hush Endura™ Spray Tan System: .................................... ............. 5 3. Prepare the Hush Optimiser™ Spray Gun .................................................................................... 6 4. Adjusting the Hush Optimiser™ Spray Gun ................................................................................. 9 5. Spraying ....................................................................................................................................... 10 6. Maintenance ................................................................................................................................. 11 7. Troubleshooting ........................................................................................................................... 13 8. Warranty Card............................................................................................................................... 17 2 HUSH endura™ ® TM Features • • • • • • • • • • • • • • • Quietest Motor 58dba (Blow TEC Magetic motor) - Think whisper quiet. Can run continuously for 24 hours - Its an absolute work horse. Motor, pre-set for Spray Tanning delivers superior airflow and so you the operator simply turn on and spray. Commercial Grade Exterior Casing - easy cleaning. Heavy-duty rubber feet to protect floors 3.5 Meters lightweight, tough flexible hose Brass quick-connections to Machine and Gun Easy to fill, simply place gun on the holder and fill the cup 3/4 full. The miniature gravity cup holds 250ml Carry Handle Stainless steel 0.5 mm fine needle tip Only 15kg with gun, 14kg without 33cm Long x 26cm High x 22cm Wide Metal Connections 58 dB 12 Month Warranty The Hush Endura™ By Solaire® provides a superior performance. Like the name the Endura™ will provide performance continuously over a 24 hour period with minimal energy consumption. When you are back to back with spray tans The Endura™ is the only option. It will work as hard as you do. Hush Endura™ By Solaire® Instruction Manual Congratulations on purchasing the Hush Endura™ tanning system. This product has been specially designed to provide the best application of professional spray tanning solutions. Take a minute to read and understand how to operate your new Hush Endura™ tanning system and you will be able to provide the perfect tan with every application. Your Hush Endura™ is packaged with the following: 1. Hush Endura™ unit. 2. 3.5m lightweight, tough Flexible Hose 3. Hush Optimiser™ Spray Gun 4. Instruction Manual (see website) 5. Warranty Card 3 GROUNDING INSTRUCTIONS Read all instructions and safety precautions before operating the unit. HUSH endura™ THISproduct INDICATES A CONDITION THAT In WILL INJURY OR LOSS OF LIFE IF THE IS This must be properly grounded. the CAUSE event of SERIOUS an electrical short circuit, grounding reduces theWARNING risk of electrical IGNORED. shock by providing an alternate path for the electrical current. 1. General Information This product isSafety equipped with a cord that has a ground wire and an appropriate ground plug. Plug the unit into an outlet ® that is properly installed and grounded in accordance with local codes and ordinances. Read instructions safety precautions before CAUSE operatingSERIOUS the unit. INJURY OR LOSS OF LIFE IF THE WARNING IS THIS all INDICATES A and CONDITION THAT COULD IGNORED. TM INSTALLATION OF THE GROUND PLUG CAN RESULT IN THE RISK OF 1 IMPROPER General Safety Information cont’d.: THIS INDICATES A CONDITION THAT WILL CAUSE SERIOUS INJURY OR LOSS OF LIFE IF THE WARNING IS IGNORED. THIS INDICATES A CONDITION THAT MAY CAUSE MINOR INJURY AND/OR 1 ELECTRICAL SHOCK. IF REPAIR OR REPLACEMENT OF THE PLUG OR CORD IS EQUIPMENT/PROPERTY DAMAGE. NECESSARY, DO Safety NOT CONNECT THE GROUND 1 General Information cont’d.:WIRE TO EITHER FLAT BLADE TERMINAL. THE WIRE WITH GREEN INSULATION (WITH OR WITHOUT A YELLOW STRIPE) IS THE General WIRE. Safety Information cont’d.: GROUNDING • Tipping the Spray Gun causes the Spray Gun to clog. Dried spray material also clogs the pressure delivery tube INDICATES ASafety CONDITION THAT COULD CAUSE SERIOUS INJURY OR LOSS OF LIFE IF THE WARNING IS IGNORED. 1THIS General Information cont’d.: and fittings. Gunregarding does notproper function when clogging occurs. 1. ForThe anySpray question installation of the ground plug, consult a qualified • Tipping the Spray Gun causes the Spray Gun to clog. Dried spray material also clogs the pressure delivery tube (licensed or certified) electrician. and fittings. SpraytoGun does notthe function when clogging occurs. •• When not in Spray use,The be sure disconnect hose and place Spray Gun into holder the turbine to avoid Tipping the Gun causes the Spray Gun to clog. Driedthe spray material alsothe clogs the in pressure delivery tube tipping. explosion! Solvent andIfpaint fumes can or ignite, causing 2. of Dofire notor modify the plug provided. the plug does notexplode fit the outlet, have the propersevere and• Risk fittings. The Spray Gun does not function when clogging occurs. When not use, be sure toTHAT disconnect the hose and placeAND/OR the Spray Gun into the holder DAMAGE. in the turbine to avoid injury andinproperty damage. INDICATES ASafety CONDITION MAY CAUSE MINOR INJURY EQUIPMENT/PROPERTY outlet installed by aInformation qualified electrician. 1•THIS General cont’d.: tipping.the Spray Gun causes the Spray Gun to clog. Dried spray material also clogs the pressure delivery tube • Tipping • When not in use, be sure to disconnect the hose and place the Spray Gun into the holder in the turbine to avoid and fittings. The Spray Gun not function when clogging occurs. GROUNDING INSTRUCTIONS • Paints and solvents containing HYDROCARBONS can react 3. This product is for usedoes on a HALOGENATED nominal 240-volt circuit and has a grounding plugexplosively that tipping. with aluminum. Always check the product’s label before using these materials in the unit. looks like the plug in Figure 2. Make sure that the product is connected to an outlet INSTRUCTIONS • GROUNDING When not in use, be sure to disconnect the hose and place the Spray Gun into the holder in the turbine to avoid This product must be properly grounded. In the event of an electrical short circuit, grounding the risk of electrical having the same configuration as the plug. No adapters should be used with thisreduces GROUNDING INSTRUCTIONS tipping. shock by providing an alternate path for the electrical current. • Hazardous vapors: Paint, solvents, insecticides and other materials may be harmful if product. GROUNDING INSTRUCTIONS • This Tipping the Spray Gun causes the Spray Gunevent to clog. spray material clogs the pressure delivery tube product must be properly grounded. In the of anDried electrical short circuit,also grounding reduces the risk of electrical inhaled, causing severe nausea, fainting or poisoning. and fittings. The Spray Gun does not function when clogging occurs. This product must bean properly grounded. In the of an current. electrical short circuit, grounding reduces thethe riskunit of electrical shock by shock by providing alternate path the electrical This product equipped with a cord that for has a event ground appropriate ground plug. into of anelectrical outlet 4. Ifis an extension is required, use only aofwire three wireanextension cord that has thePlug Thisproviding product must be properly In current. the event an and electrical short circuit, grounding reduces the risk an alternate pathcord forgrounded. the electrical GROUNDING INSTRUCTIONS that is properly installed and grounded in accordance with local codes and ordinances. • Make sure the is well ventilated. Avoid all ignition sources, such as static electricity same configuration as the unit including the place (round) ground Make shock by providing anroom alternate path for thecord, electrical current. • This When not inisuse, be sure to the hose and Sprayterminal. Gun ground into theplug. holder inthe theunit turbine tooutlet avoid product equipped with adisconnect cord that has afrom ground wire and the an appropriate Plug into an sparks, open flames, hot objects, sparks connecting and disconnecting power cords, sure that the extension cord is plugged into a properly grounded receptacle. This product is equipped with a cord that has a ground wire and an appropriate ground plug. Plug the unit into an outlet that is properly tipping. that is properly installed and grounded local codes andcircuit, ordinances. This product must be properly grounded.inInaccordance the event ofwith an electrical short grounding reduces the risk of electrical and working light switches. Thisinstalled product is equipped with a cord that a codes groundand wire and an appropriate ground plug. Plug the unit into an outlet and grounded in accordance withhas local ordinances. shock by providing an alternate path for the electrical current. 5. When using and an extension be sure it is in good condition heavy enough to that is properly installed groundedcord, in accordance with local codes andand ordinances. • Follow the the material and solvent manufacturers’ safety precautions and warnings. Do not meet specifications in the chart below. If an extension cord is needed the GROUNDING INSTRUCTIONS This product is equipped with a cord that has a ground wire and an appropriate ground plug. Plug the unit into an outlet IMPROPER INSTALLATION OF THE GROUND PLUG CAN RESULT IN THE RISK OF use liquids with flash points less than 100 degrees Fahrenheit (38 degrees Celsius). I following wire sizes must be used. that is properly installed and grounded in accordance with local codes and ordinances. ELECTRICAL SHOCK. IF REPAIR OR REPLACEMENT OF THE PLUG OR CORD IS This productDO must be properly grounded. In the event of anCAN electrical short grounding reduces the risk of electrical IMPROPER INSTALLATION OFTHE THE GROUND PLUG RESULT INcircuit, THE OFconductive NECESSARY, NOT CONNECT GROUND WIRE EITHER FLAT BLADE TERMINAL. • Static electricity can beOF produced by HVLP spraying. Make any electrically IMPROPER INSTALLATION GROUND PLUG CANTO RESULT INsure THE RISK OFRISK 6.by (See Chart 1) Figure 2THE shock providing an alternate path for the electrical current. ELECTRICAL SHOCK. IF REPAIR OR OF THE OR PLUG ORISCORD IS THE WIRE GREEN INSULATION (WITH OR WITHOUT APLUG YELLOW STRIPE) IS THE ELECTRICAL SHOCK. IF REPAIR ORGROUND REPLACEMENT OF THE objectWITH being sprayed isOF grounded toREPLACEMENT prevent static sparking. The sprayer grounded to IMPROPER INSTALLATION THE PLUG CAN RESULT INCORD THE RISKis OF NECESSARY, DO NOT CONNECT THE GROUND WIRE TO EITHER FLAT BLADE TERMINAL. GROUNDING WIRE. NECESSARY, DO NOT CONNECT THE GROUND WIRE TO EITHER FLAT BLADE prevent static sparking. The25’ spray grounded through the PLUG electrical cord. If IS an extension ELECTRICAL SHOCK. IF REPAIR OR REPLACEMENT OF THE OR CORD cord……………………..…….10, 12, or 14 Gauge This product isTHE equipped with aGREEN cord that has a ground wire an appropriate ground IS plug. Plug the unit into an outlet THE WIRE WITH GREEN INSULATION OR WITHOUT A wires YELLOW STRIPE) THE TERMINAL. WIRE WITH INSULATION (WITH ORand WITHOUT A YELLOW cord is necessary, the cord must be a(WITH grounded with three made the appropriate NECESSARY, DO NOT CONNECT THE GROUND WIRE TO EITHER FLAT BLADE TERMINAL. 50’ cord……………………….………..10 or 12 for Gauge that is properly installed and grounded in accordance with local codes and ordinances. GROUNDING WIRE. IMPROPER INSTALLATION THE GROUND PLUG CAN RESULT IN THE RISK OF ISused. THE GROUNDINGOF WIRE. voltage THESTRIPE) WIRE WITH GREEN INSULATION (WITH OR WITHOUT A YELLOW STRIPE) IS THE 100’ cord………………………………………10 Gauge ELECTRICAL SHOCK.regarding IF REPAIR OR installation REPLACEMENT OF THEplug, PLUG OR CORD IS 1. For any question proper of the ground consult a qualified GROUNDING WIRE. 1. Foraany question regarding proper THE installation of the groundTO plug, consult a may qualified NECESSARY, DO NOT CONNECT GROUND WIRE EITHER FLAT BLADE TERMINAL. (licensed or certified) electrician. • Use respirator or mask whenever there is a chance that vapors be inhaled. Read Chart 1 Extension Cord Requirements (licensed or certified) electrician. 1. For any question regarding proper installation of the ground plug, consult a qualified THEall WIRE WITH GREEN INSULATION (WITH OR WITHOUT A YELLOW STRIPE) IS THE instructions with the mask to ensure that the mask will provide the necessary (licensed orthe certified) electrician. GROUNDING WIRE. 2. Do modify pluginhalation provided. Ifofthe plug does not ground fit the outlet, have the proper against the harmful vapors. 4RESULT 1.protection Fornot any question regarding installation plug,the consult qualified IMPROPER INSTALLATION OF proper THE GROUND CAN INproper THE aRISK OF 2. Do not modify the plug provided. If the plug does PLUG notoffitthe the outlet, have outlet installed by a qualified electrician. Fig 1 (licensed or certified) electrician. outlet installed by a qualified electrician. ELECTRICAL SHOCK. IF REPAIR OR REPLACEMENT OF THE PLUG OR CORD IS not modify the plug provided. If the plug does not fit the outlet, have the proper • Do2.notDo carry the turbine while spraying. NECESSARY, DO CONNECT THE GROUND WIRE TO EITHER FLAT BLADE TERMINAL. outlet by aon qualified electrician. 1.This For anyinstalled question regarding proper installation of the ground plug, consult a that qualified 3. product isNOT foruse use a nominal 240-volt circuit and has a grounding plug 2. WIRE Do not modify the plug provided. If the plug does not outlet, havethat the proper 3. This product isGREEN for on a nominal 240-volt circuit and hasfita the grounding plug THE WITH INSULATION (WITH OR WITHOUT A YELLOW STRIPE) IS (licensed orplug certified) electrician. looks like the Figure 2.electrician. Make sure that the the product is connected to an outlet THE • Keep turbine at the maximum distance from area. outlet installed by qualified looksthe like the plug inain Figure 2. Make sure that the product isspraying connected to an outlet GROUNDING WIRE. 3. This product is for use on a nominal 240-volt circuit and has a grounding plug that having thesame sameconfiguration configuration as the No adapters used having the as the plug.plug. No adapters shouldshould be usedbewith thiswith this looks like the plug in Figure 2. Make sure that the product is connected to an outlet 2. Do not modify the plug provided. If the plug does not fit the outlet, have the product. 3. product. This product is for use on a nominal 240-volt circuit and has a grounding plug proper that having the same configuration as the plug. No adapters should be used with this outlet installed by a qualified electrician. like plug inregarding Figure 2.proper Make sure that theofproduct is connected to ana outlet 1. looks For any the question installation theextension ground plug, consult qualified 4. an extension cord required, use only a three wire cord that has this the 4. IfIfhaving an product. extension cord is is required, use only aplug. three wireadapters extension thewith 3cord that the same configuration as the No should behas used (licensed or certified) electrician. 3.same This product is as for use on a cord, nominal 240-volt andground has a grounding plug that configuration asthe the unit including thecircuit (round) terminal. Make same configuration unit cord, including the ground terminal. Make product. 4. Ifthat an the extension cord isisrequired, useinto only a three wire extension cord that hasoutlet the looks like the plug incord Figure 2. Make the product is connected to an sure extension cord plugged into asure properly grounded receptacle. sure the extension is plugged a that properly grounded receptacle. 2. Do not configuration modify theconfiguration plug Ifthe theincluding plug No does fit the outlet, have the proper same as provided. the unitas cord, thenot (round) ground terminal. Make having the same plug. adapters should be used with this 4. If an extension cord required,electrician. use only a three wire extension cord that has the outlet installed by ais qualified sure thatan the extension is plugged into a properly receptacle. 5. When When using extension cord,cord be be sure it is it in is good condition andgrounded meets specifications. product. 5. using an extension sure in the good condition and terminal. heavy enough same configuration as thecord, unit cord, including (round) ground Make to Fig 2 meet the specifications in the chart below. If an extension cord is needed the sure that the extension cord is plugged 240-volt into a properly grounded receptacle. 3. This product is for use on a nominal circuit and has a grounding plug that 5. When using an extension cord, be sure it is in good condition and heavy enough to 4. If an extension cord is required, use only a three wire extension cord that has the wire sizes must be used. and tested every 12 months after initial purchase to comply with Australian Electrical Safety 6. following Ensure the Hush Endura™ is tagged looks like plug in 2. cord, Makeincluding sure that theextension productground iscord connected to an meetconfiguration the the specifications the chart below. If an isterminal. needed theoutlet same asFigure theinunit the (round) Make standards. 5. When using an extension cord, beassure itplug. is in No good condition and heavy enough to having the same configuration the adapters should be used with this following wire sizes must beisused. sure that the extension cord plugged properly grounded receptacle. 6. (See Chart 1) Figure 2 in meet the specifications the chart below.into If ana extension cord is needed the product. 7. Always turn off power switch of Hush Endura™ and remove plug after operation. following wire sizes must be used. (See using Chart an 1) Figure 2 cord……………………..…….10, 5.6. When extension cord, be sure it is in good condition and enough to 25’ 12, or 14heavy Gauge Ifaware an extension required, onlyfrom aIfthree wireNever extension that the hasjust thepulling the flexible part of the power 8. 4.Bemeet to hold thecord solidis plug bodychart touse remove socket. remove theGauge plug by the specifications incord……………………….………..10 the below. an extension cord iscord needed 50’ or 12 6. cord (See Chart 1) Figure 2as the unit cord, including the (round) ground terminal. Make same configuration following wire sizes must be used. cord……………………..…….10, 12, orGauge 14 Gauge 100’25’ cord………………………………………10 sure that the extension cord plugged into a properly grounded receptacle. 50’ is cord……………………….………..10 or 12 Gauge 25’ cord……………………..…….10, 12, by or an 14authorised Gauge technician only as this voids all warranty. 9. 6.Disassemble or1) maintenance the cord………………………………………10 Hush Endura™ is to be conducted (See Chart Figure 2 of 100’ Gauge 1 Extension Cord Requirements 50’ cord……………………….………..10 or 12 Gauge 5. When using an extension cord,Chart be sure it is in good condition and heavy enough to cord………………………………………10 Gauge 10. Domeet not operate near water100’ orinmoisture as below. electrocution may occur. cord is needed the specifications the chart If an extension the 4 Cord 25’ cord……………………..…….10, 12, or 14 Gauge Chart 1 Extension Requirements 4 following wire sizes must be used. 50’ cord……………………….………..10 or 12 Gauge Chart 1 Extension Cord 4 Requirements Gauge 100’ cord………………………………………10 6. (See Chart 1) Figure 2 HUSH endura™ 2. Set up and operate your Hush Endura™ Tanning System ® TM 1. Plug the Hush Endura™ tanning system unit into a proper electrical outlet. Make sure that the electric current you are connecting to is the same as your unit. (240v). DO NOT attempt to connect the unit to the wrong electric current as this 2 Set up and operate your PRINCESS Tanning System: will not only damage your unit but also void your warranty. 1. Plug the PRINCESS tanning system unit into a proper electrical outlet. Make sure that the electric current 2. Next, locate the male end of the air hose and connect it to the female quick connect on the Hush Endura™ tanning you are connecting to is the same as your unit. (110v or 220v). DO NOT attempt to connect the unit to the wrong system. electric current as this will not only damage your unit but also void your warranty. a. To insert the male connection pull back on the ring of the brass coupler located on the Hush Endura™ system male and connector onitthe hose. Figure 6. connect on the PRINCESS 2. Next, tanning locate the male and end insert of the the air hose connect to the female quick tanning system. a. To insert the coupler pull back on the ring of the black coupler located on the PRINCESS tanning system and connect it to the male connector on the hose. Figure 6. Fig. 6 b. Release the ring to allow the coupler to snap into place. The hose should now be connected to the unit Figure 7. Fig. 6 b. Release the ring to allow the coupler to snap into place. The hose should now be connected to the unit Figure 7. Fig. 7 7 brass coupler and remove c. To remove the air hose, pull back on the ring Fig. of the d. See page 7 for How to connect the Hush Endura™ to the Hush Optimiser™ spray gun. c. To remove the air hose, pull back on the ring of the black coupler and remove To Turn the UNIT ON Press the red power switch button. IfIfyou Endura™ to cool down for about youhave havejust justfinished finishedspraying, spraying,the theconnector connectormay maybe behot. hot.Allow Allowthe theHush PRINCESS unitunit to cool down or minutes about 10before minutes before disconnecting thefrom air hose from turbo unit. 5 the 10 disconnecting the air hose the Hush Endura™ unit. Use Use Caution! Caution! 5 HUSH endura™ 3 Prepare the Hush Optimiser™ Spray Gun: 6 ® TM HUSH endura™ 3 Prepare the Hush Optimiser™ Spray Gun cont’d ® TM Fig. 6 b. Release the ring to allow the coupler to snap into place. The hose should now be connected to the unit Figure 7. Fig. 7 1. Follow the diagram to prepare the Hush Optimiser™ Spray Gun c. plastic To remove the the air hose, back on the ringGun. of the black coupler and remove a. Unscrew the cup from Hush pull Optimiser™ Spray Pour tanning solution into the cup. Do not fill more than ¾ full. If you have justscrew finished spraying, thethe connector may be hot. the PRINCESS unitScrew to cool b. Carefully the cup back onto main body of the HushAllow Optimiser™ Spray Gun. the down cup on firmly but or about 10 minutes before disconnecting the air hose from the turbo unit. Use Caution! 5 DO NOT over tighten. Over tightening will cause the cup to “pop” and damage the threads. Leakage can then occur requiring replacement of the cup. c. Locate the air cap (#1) on the Hush Optimiser™ diagram. With the gun facing towards you, slightly turn the air cap ring (#1-1, page 6) anti clockwise to loosen the air cap. Notice that you can now rotate the air cap freely. d. Look at Mist Applicator Patterns diagram above. Note the position of the air cap and the direction of the spray pattern. Pattern 1 is for spraying across from side to side. Pattern 2 is for spraying up and down. Patterns 1 and 2 are the most common positions for applying tanning solutions. 7 HUSH endura™ 3. Prepare the Hush Optimiser™ Spray Gun cont’d ® TM e. Turn the air cap (#1) to the position you want. Again with the gun facing towards you, turn the air cap ring (#1-1, page 6) clockwise to lock the air cap in place. f. The spray pattern can be changed from flat to circle using the Pattern Adjusting knob (#12). A circle pattern (as seen below) can be used for contouring. ← ← Pattern Adjusting Knob How to mist in a spot or circle 2. Next, position the Hush Endura™ unit as far away as practical and possible from the area where you will be spraying. 3. Attach the remaining end of the hose to the Hush Optimiser™ Spray Gun as follows: a. Locate the male connection at the bottom of the Hush Optimiser™ Spray Gun. See figure 8. b. Pull back on the coupler of the brass connector on the air hose. ← Fig 8 8 Flow Solution Screw HUSH endura™ 2 Set up and operate your PRINCESS Tanning System: 4. Adjusting the Hush Optimiser™ Spray Gun 1. Plug the PRINCESS tanning system unit into a proper electrical outlet. Make sure that the electric current ® TM you connecting is the(#22, same as your 220v). DOdiagram. NOT attempt to connect the unit to the wrong 1. Locate theare Solution Flow to Screw page 7) onunit. the (110v Hush or Optimiser™ electric current as this will not only damage your unit but also void your warranty. 2. Face the front of the Hush Optimiser™ gun away from you and turn the Solution Flow Screw clockwise. This reduces 2. Next, locate the male end of the air hose and connect it to the female quick connect on the PRINCESS and will eventually stop the flow of solution. DO NOT over-tighten the screw as this will cause damage to the end of tanning system. the needle. Once the trigger cannot be pulled back there is no point in tightening the screw down more, this will only a. of Tothe insert the coupler pull back on the ring of the black coupler located on the PRINCESS tanning damage the end needle. system and connect it to the male connector on the hose. Figure 6. 3. Turning the Solution Flow Screw anti clockwise will increase the flow of solution and turning the solution flow screw clockwise will decrease the flow of solution. 4. In general, 1 ½ - 2 full turns from the fully closed position will provide a good solution flow. You may find that you want more or less solution. You can adjust the Solution Flow Screw to your desired setting. NOTE: Opening the Solution Flow Screw more than 3 turns will not increase the solution flow and will in fact decrease the efficiency of your Hush Optimiser™ Spray Gun. 5. In general, hold the Hush Optimiser™ Spray Gun 20-30cm from the person being sprayed. Moving the Hush Fig. 6 Optimiser™ Spray Gun back will increase the size of the mist pattern. Moving the Hush Optimiser™ Spray Gun closer b. Release the ring to allow the coupler to snap into place. The hose should now be connected to the will decrease the size of the mist pattern. The further away you hold the Hush Optimiser™ Spray Gun, the more you will unit Figure 7. need to increase the solution flow thus causing abnormal amounts of airborne solution (overspray). 6. Holding the Hush Optimiser™ Spray Gun closer to the person being sprayed along with a minimum flow of solution will provide the best results, no streaks or running solution and virtually no mist in the spray area. 7. Be sure to move the Hush Optimiser™ Spray Gun at a slow, steady speed keeping the distance of the Spray Gun the same throughout the application. This will ensure perfect results. It is actually very easy. Practice, Practice, Practice. 8. It is best to hold the Hush Optimiser™ Spray Gun in a vertical position when spraying. If you want to change the direction of the mist pattern, rotate the position of the air cap rather than turning the Hush Optimiser™ Spray Gun on its Fig. 7 side. Refer to the spray gun pattern diagram on page 7/8. c. store To remove air hose, pull back on in thea ring of the black coupler and habit remove 9. Always hold or the Hushthe Optimiser™ Spray Gun vertical position. It is a good to use, when you are not spraying. If you have just finished spraying, the connector may be hot. Allow the PRINCESS unit to cool down or 10over-tighten minutes before disconnecting the air hose unit. Use 10.about Do not the solution flow screw (#22, page from 7)5as the this turbo will damage the Caution! end of the needle point. Tighten the screw until the needle cannot be pulled back. Once this point is reached there is no point in turning the solution slow screw anymore as this will only cause damage to the needle point. 9 HUSH endura™ 5. Spraying ® TM You should now be ready to spray your client. Good quality results with your Hush Endura™ spray tanning system are a combination of careful preparation of your client, a proper spraying environment, a basic knowledge of the solution you will be using and how these solutions work with your Hush Endura™ spray tanning system. 1. You are now ready to begin spraying. 5 2. TheSpraying/Misting ON/OFF Switch is located at the side of the Hush Endura™ Unit. Turn it on. You will hear a sound similar to a vacuum cleaner. You may also notice that air is now blowing out of the front of the Hush Optimiser™ Spray Gun. This is a. You are now ready to begin misting. correct. Air will continually flow from the air cap of the Hush Optimiser™ Spray Gun as long as the Hush Endura™ Unit is b. The and ON/OFF located under the carry handle of the Turbo Unit. Turn it on. You will hear a running the airSwitch hose isisconnected. sound similar to a vacuum cleaner. You may also notice that air is now blowing out of the front of the Spray Thismotor is correct. continually flow from the air cap the Spray Gun as long as the 3. Your HushGun. Endura™ unit isAir setwill for the perfect atomisation of spray tan of solution. Turbo Unit is running and the air hose is connected. 4. Open the Solution Flow Screw as described in item 4 and set the Pattern Adjustment Knob. c. Open the Solution Flow Screw as described in item 4. d. Set the mist pattern you wish to use by adjusting the air cap to the desired position. Refer to Mist 5. Set the mist pattern you wish to use by adjusting the air cap to the desired position. Refer to the spray gun pattern Pattern Diagram. diagram on page 7/8. e. Direct the Spray Gun to the area of the body that you want to start spraying. 6. Direct the Hush Optimiser™ Spray Gun to the area of the body that you want to start spraying. f. Pull back on the trigger (#13) and move the Spray Gun as noted in the diagram below. Do not wave the Spray Gun back and forth in front of your client by bending your wrist. Rather, keep your wrist straight 7. Pull back on the trigger (#32, Diagram on page 7) and move the Hush Optimiser™ Spray Gun as noted in the diagram and move your entire arm. Movement should be steady, even and deliberate, keeping your distance the below. Do not wave the Spray Gun back and forth in front of your client by bending your wrist. Rather, keep your wrist same at all times. straight and move your entire arm. Movement should be steady, even and deliberate, keeping your distance the same at all times. PROPER MISTING TECHNIQUE 10 HUSH endura™ 6. Maintenance ® TM 1. Hush Endura™ Unit. a. There is minimal maintenance to perform on the Hush Endura™ unit. Make sure you keep the motor unit as far away from your spraying area as possible. b. Every night wipe over Hush Endura™ unit with a damp cloth. Please Note: Ensure no excess water is used as this will short circuit the unit. c. Please see maintenance cleaning video at: http://www.solaire.com.au/Main.asp?_=Sunless Education 2. Air Filter. a. Remove the air filter at the base of the unit and wash at the end of every week under hot soapy water. Ensure it is dry before replacing it. Replace the white filter when it can’t be washed anymore. 3. Air Hose. a. Wipe the air hose daily with a damp cloth and store in a clean dry place. 4. Hush Optimiser™ Spray Gun - Daily Clean. a. It is important to clean your Hush Optimiser™ Spray Gun daily. b. At the end of the day or when the equipment will not be used any more, disconnect the Hush Optimiser™ Spray Gun from the air hose. c. Carefully unscrew the cup. If there is remaining solution, either close the cup with a lid, or pour the remaining solution into a proper storage container. d. Rinse the cup under hot running water until clean. e. Turn the gun upside down and allow hot running water to run into the plastic tube, pull back the trigger and allow the water to flow out of the nozzle. Continue until clear. f. Fill the cup about ¼ full with AIRBRUSH CLEANER. Reconnect the Hush Optimiser™ Spray Gun to Air Hose. Turn on the Hush Endura™ Unit. Direct the Hush Optimiser™ Spray Gun to a safe area and spray the AIRBRUSH CLEANER through the Hush Optimiser™ Spray Gun until the cup is empty and until the Spray becomes CLEAR. g. Turn off the Hush Endura™ Unit. Disconnect the Hush Optimiser™ Spray Gun. Unscrew the cup. h. Start to dismantle your Hush Optimiser™ Spray Gun. i. Unscrew and remove the Air Cap Ring (#1, Diagram on page 7). Rinse the threads under warm running water. Wipe, the threads and dry. Add a small amount of Spray lube or Vaseline to the threads. j. Reinstall the two pieces you just removed by reversing the removal procedure. Your Hush Optimiser™ Spray Gun should be ready for the next use. j. Please see Spray Gun maintenance cleaning video at: http://www.solaire.com.au/Main.asp?_=Sunless Education 11 HUSH endura™ 6. Maintenance Cont’d ® TM 5. Hush Optimiser™ Spray Gun - Weekly Clean. Perform the Daily procedure then continue: a. The Solution needle (#20, Diagram on page 6) To remove: Face the front of the gun away from you, turn the Solution flow screw anti clockwise until it comes out of the Spray Gun. Be careful when removing the solution flow Screw as there is a small spring (#21, Diagram on page 6) around the needle. Do not loose it. This is important to the operation of the Hush Optmiser™ Spray Gun. Set the spring aside and pull the trigger all the way back until you can grab the needle with your finger tips and pull it out from the back of the Hush Optimiser™ Spray Gun. Once removed, rinse under the hot running water, dip into AIRBRUSH CLEANER and dry. Add gun lubrication or vaseline to the needle. Simply rub a small amount of Spray Gun lube or vaseline around the needle shaft and spring. Later to reinstall repeat these steps in reverse. b. The solution nozzle (#2, Diagram on page 6) can be removed for additional cleaning as it is recommended to, the needle must first be removed to do this procedure. With an adjustable wrench or spanner that is supplied when you purchase the unit, place the tip of your adjustable wrench or spanner on the nut of the nozzle (whilst the gun is facing you) and twist anti clockwise. Be careful. Rinse under hot running water, take a cotton bud or the brush supplied and dip it into gun cleaner and clean inside the threads. DO NOT USE ANYTHING METAL as it will scratch the threads or nozzle and this will cause leaking. To reinstall repeat these steps in reverse. c. Please see Spray Gun maintenance cleaning video at: http://www.solaire.com.au/Main.asp?_=Sunless Education HVLP Gun/Airbrush Cleaner: Specially formulated to breakdown and remove spray tanning ingredients and residue from Airbrush/HVLP tips & nozzles. When using spray tan in your Hush Optimiser™ spray gun it can leave a build-up of residue that, overtime, can clog your Hush Optimiser™ spray gun tip and interfere with the effectiveness of your spray pattern. Solaire’s Airbrush Cleaner is specifically developed to breakdown the residue left in your airbrush tip or spray gun nozzle. 12 Spray Tan Gun Cleaner Available through our Office – please call us! *Excluded any parts that may be required to be replaced. HUSH endura™ 7. Troubleshooting ® TM Q. Hush Endura™ unit turned ON. Air blows out of Hush Optimiser™ Spray Gun? • This is correct. Air blows constantly when Hush Endura™ unit is ON. Q. Hush Endura™ unit is turned ON the trigger is pulled back on Hush Optimiser™ Spray Gun but no solution comes out? • Check that the cup is screwed firmly to Hush Optimiser™ Spray Gun. • Check that there is no solution bubbling or leaking around the cup. • Turn Hush Endura™ unit OFF. Unscrew cup. Be sure that Solution Tube (#39, Diagram on page 7) is connected and has not come loose. • Turn Hush Endura™ unit OFF. Remove air cap ring (#1-1, Diagram on page 6) remove air cap (#1-2, Diagram on page 6) remove the needle (#20, Diagram on page 6) remove nozzle (#2, Diagram on page 6) with an adjustable wrench or spanner which is supplied at purchase. Rinse Solution Nozzle under running water and check for dried solution that may have blocked the hole. Reinstall Solution Nozzle, solution needle, air cap and air cap ring. Try spraying again. Q. Solution leaks in front of trigger? • With an adjustable wrench or spanner tighten Solution Needle Packing Screw (#28, Diagram on page 6). Do not over tighten. This can cause Solution needle to stick and not spring back. Try spraying again. If leaking continues the Solution Needle Packing needs to be replaced. (Rare). Remove solution needle (#20, Diagram on page 6), then remove Solution Needle Packing Screw (#28, Diagram on page 6). Dry out the Solution Needle Packing’s Replace. Reinstall Solution Needle Packing Screw and solution needle. Tighten all the way, and then back off slightly. (1/8 turn) Test the Hush Optimiser™ spray gun for leakage. Q. When Hush Endura™ unit is ON, Solution continues to spray from the Hush Optimiser™ Spray Gun without trigger being pulled? • Immediately turn Hush Endura™ unit OFF. • Disconnect Hush Optimiser™ spray gun from air hose. • Slightly adjust (loosen) Solution Needle Packing Screw (#28, Diagram on page 6). Test to see if problem is resolved. • Check to see that Needle Spring is installed. (#21, Diagram on page 6). Remove Solution Flow Screw (#22, Diagram on page 6). Look for Needle Spring around the back of the Solution Needle. If lost, order for replacement. • Check Solution nozzle. Remove and clean following the spray gun weekly clean directions on page 12. Q. Solution leaks around the top of the cup. • Make sure there is a gasket (#36, diagram on page 6) • Make sure the cup is screwed firmly to the body of the Hush Optimiser™ Spray Gun. • Make sure the threads around the cup are clean and the threads inside the cup top assembly are clean. • Replace the cup top gasket. Pry out old gasket. Install new gasket. Test Hush Optimiser™ spray gun. 13 HUSH endura™ 7. Hush Optimiser™ Spray Gun Problems ® TM 14 HUSH endura™ RECORD OF Hush Endura™ USE ® TM MODEL SERIAL# DATE PURCHASED DATE HOURS OF USE TOTAL HOURS 15 HUSH endura™ RECORD OF Hush Endura™ MAINTENANCE DATE ® TM MAINTENANCE PERFORMED 16 Solaire Warranty Card Mobile: Purchased from: Yes Serial Number: No Salon or Business Name: Solaire Pty ltd Name: Address: Telephone Number: Email address: Date of Purchase: Proof of Receipt with matching serial number is copied and attached? Model: Date: / / I have read and understood the terms and conditions in the Solaire Warranty Card and I have completed the necessary requirements. Purchaser’s Acknowledgement Signature: A warranty is provided with this piece of equipment provided it is used in conjunction with manufactures instructions and THE WARRANTY CARD IS RETURNED within 14 days of receipt of purchase AND prior to use the purchaser acknowledges reading and fully understanding the Manufactures Instruction Manual. You must complete your spray tan gun maintenance and equipment care training module. If you fail to complete all three of the above YOU VOID your warranty. The most common cause of failure of any spray tan equipment is lack of cleaning, so take the time to make sure you look after your investment. Please ensure you read the instructions carefully and complete the spray tan gun maintenance and equipment care training module at www.solaire.com.au. You will need to register on the site prior to completing your training. The website is also full of a whole range of products and education to help you as the spray tan specialist ensure you deliver the most professional customer service and an award winning Solaire spray tan. • Complete your contact details. Attach a copy of the original receipt showing the serial number. Email to: [email protected]. • Read the Manufactures Instruction Manual. • Register at www.solaire.com.au and complete the spray tan gun maintenance and equipment care training module. This is found in the education tab on the left hand side of the home page. Click on sunless education and watch the video. 5. 6. 7. 8. 3. 4. 2. 1. Email: [email protected] to request a WARRANTY Claim Form. Fill in the WARRANTY claim form and email it to: [email protected]. Try to include as much detail as possible about the problem. If at all possible we try to help you solve the problem and therefore you may be contacted regarding your claim either via phone or email. If we are unable to solve the issue the equipment will need to be assessed and it will need to go to one of our Authorised repairers - we will issue you a claim number. Once you have your claim number insert the number on Warranty Claim Form. Ensure equipment is clean, dry and securely wrapped to prevent any leaking of fluid and well-padded and packaged to prevent damage to the equipment during shipping. Send the form with the goods to the address on the WARRANTY CLAIM FORM. Send a copy of the receipt from the original purchaser showing serial number, place of purchase, date of purchase. You will be required to pre - pay all shipping charges. Our Authorized repairer will attend to you claim promptly and contact you to discuss after they have assessed the claim. Warranty Procedure: Solaire will extend a warranty on equipment as provided by the Manufactures Instruction Manual of the goods. Solaire Pty Ltd warrants that products assembled by Solaire Pty Ltd shall be free from defects as it relates to Solaire Pty Ltd workmanship for a period as outlined in the Manufactures Instruction Manual for each respective piece of equipment from the date of purchase from Solaire Pty Ltd or its distributors or agents to the buyer. If during the warranty period, the goods should prove defective as determined by Solaire Pty Ltd or its authorized repairer, then the Solaire can, at their discretion, repair or replace the goods. In no event shall Solaire Pty Ltd, manufacturer of goods, their subsidiaries and affiliated companies, be liable for special, incidental, or consequential damages, including loss of profits, whether or not caused by or resulting from negligence of seller. In addition, this warranty shall not apply to any goods or portions thereof which have been subjected to abuse, misuse and improper installation, maintenance or operation, electrical failure or abnormal conditions, and to goods which have been tampered with, altered, modified, repaired or reworked by anyone not approved by Solaire Pty Ltd. Solaire Pty Ltd warranty herein is in lieu of and excludes all other warranties of seller and the distributor of the goods and their subsidiaries and affiliated companies, whether expressly implied, statutory or otherwise created under applicable law including, but not limited to, the warranty of merchantability and the warranty of fitness for particular purpose or use. This Warranty does NOT include: misuse, damage, neglect, alterations, disassembled equipment or modifications, lack of maintenance, cleaning, water damage to electrical parts and INCORRECT VOLTAGE CONNECTION.