Transcript
HY1601 IN-DASH DIN RADIO INSTALLATION KIT FOR SELECT
1995-UP HYUNDAI/MITSUBISHI VEHICLES VEHICLE APPLICATIONS: HYUNDAI 1995-99 1992-94 1995-00 1990-99 1986-89 1991-96
ACCENT ...................................... 2 ELANTRA ..................................... 2 ELANTRA ..................................... 2 EXCEL ......................................... 2 EXCEL ......................................... 3 SCOUPE ...................................... 3
HYUNDAI (Cont'd) 1989-94 SONATA ...................................... 4 1995-99 SONATA ...................................... 4 1997-99 TIBURON ..................................... 4 MITSUBISHI 1990-93 PRECIS ........................................ 3 1987-89 PRECIS ........................................ 3
ILLUSTRATION 1
REAR SUPPORT STRAP
ELANTRA LEFT BRACKET ACCENT LEFT BRACKET MOUNTING PANEL 2364
ELANTRA RIGHT BRACKET
PANEL 1541
ACCENT RIGHT BRACKET REAR SUPPORT STRAP
ELANTRA BRACKET
SHAFT RADIO
EXCEL BRACKET
ELANTRA BRACKET EXCEL BRACKET PANEL 2029
CAUTION: Rear supporting the radio adds to the installation's structural integrity.
INTRODUCTION/PRELIMINARY Thank you for purchasing the Scosche HY1601 Installation Kit. This installation kit was manufactured to the highest quality standards with the best materials available. CAUTION: Disconnect your vehicle’s negative battery terminal before the installation to help prevent electrical damage. We recommend the use of a volt/ohm meter over a test light to check wiring. A test light or grounded wire probe can cause damage to the vehicle’s computer and/or diagnositic systems. Avoid all factory air bag wiring - air bags can accidentially deploy causing serious injury or death. NOTES: • See your vehicle’s instructions for any special tools your installation might require. • Read all instructions accompanying your car stereo/cassette player for proper wiring and mounting instructions.
FACTORY WIRE CODES For Factory Wiring Codes go to: www.scosche-cars.com LIABILITY DISCLAIMER This instruction booklet is based on carefully documented data and research of automobile dash disassembly, wire harness/codes and information pertaining to installation of this kit HY1601 in select 1995-UP Hyundai / Mitsubishi Vehicles. Scosche Industries, Inc. cannot be held responsible for discrepancies/inconsistencies that may occur due to the automobile manufacturing changes or options, or damage that may occur in the automobile during the installation of components while using this booklet.
If you have any further questions, call © 2002 SCOSCHE INDUSTRIES, INC.
TECH HELP: 1-800-621-3695x3 SI 10/02-HY1601 (3000003)
RADIO / KIT AS SEMBL Y ASSEMBL SEMBLY ILLUSTRATION 2
SHAFT MOUNT RADIOS Using the hardware supplied with the radio, secure the radio shafts to the mounting panel (kit) as shown in Illustration1. DIN RADIOS Remove the sections indicated in Illustration 2. Use side cutters, an X-acto knife or hacksaw blade to cut the top and bottom sections (follow the cut lines) then simply pull outward to break off each tab.
DIN CHASSIS CUTLINES
USE PILERS TO BREAK AWAY, OR SIDE CUTTERS (WIRE CUTTERS) TO CUT THE UNNECESSARY BRACKETS OFF.
REMOVING THE TABS This kit features breakaway mounting tabs for all applications. Tabs that will not be used in a particular installation need to be cut off. Use the shaded brackets and tabs. 1995-99 Hyundai Accent
Read page 2 for kit assembly.
RADIO REMOVAL: 1. Extract (4) 10mm bolts from panel below steering column. 2. Remove ashtray and extract (2) screws from the ashtray cavity. 3. Open glovebox and use a panel removal tool to remove the glovebox stopper. 4. Extract (2) screws and remove entire glove box. 5. From behind glovebox area, unclip LEFT SIDE RIGHT SIDE climate control cable. ATTACH ATTACH ACCENT ACCENT 6. Unclip (2) climate control cables SPACERS SPACERS from behind steering column panel on the side of duct/fan assembly. USE THIS TAB USE THIS TAB 7. Unsnap radio trim bezel, unplug FRONT OF PANEL 2364 and remove bezel. 8. Extract (4) screws holding radio in, unplug connectors, antenna, and remove radio.
PANEL 2364
USE THE SHADED BRACKETS & THE INDICATED SPACERS.
1996-UP Hyundai Elantra
Read page 2 for kit assembly.
RADIO REMOVAL: 1. Carefully pop out shifter trim bezel and remove one screw at the bottom of the radio dash bezel. 2. Pop out dimmer control switch, unplug and remove. 3. Extract (1) screw from dimmer switch location. LEFT SIDE 4. From driver’s side underdash area (above gas pedal) unhook temperature control cable. 5. Carefully pry out on radio dash bezel, to ATTACH ELANTRA unsnap, unplug all switches, vacuum SPACERS lines and remove. 6. Extract (4) screws securing radio, USE THIS TAB unplug and remove.
PANEL 2364
RIGHT SIDE
ATTACH ELANTRA SPACERS
USE THIS TAB
FRONT OF PANEL 2364
USE THE SHADED BRACKETS & THE INDICATED SPACERS.
1992-95 Hyundai Elantra
Read page 2 for kit assembly.
RADIO REMOVAL: 1. Remove the ashtray and extract the two screws from the inside. 2. Locate and remove the cover cap next to the steering wheel and extract the screw behind that is securing the radio dash bezel to the sub dash structure. LEFT SIDE USE THESE 3. Carefully pull outward on the radio dash TABS bezel releasing the clip on the top right corner. Disconnect all the connectors and remove. 4. Extract the four screws securing the radio to the sub dash structure. Disconnect all connectors and remove. ATTACH ELANTRA SPACERS
PANEL 2029
RIGHT SIDE USE THESE TABS
FRONT OF PANEL 2029
ATTACH ELANTRA SPACERS
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS AND DISCARD.
2
Read page 2 for kit assembly.
1990-UP Hyundai Excel 1990-UP Mitsubishi Precis
PANEL 2029
RADIO REMOVAL: NOTE: The factory radio mounting unit is fastened to the trim panel. The chassis is inserted into a "pocket" in the cavity. 1. Remove the ashtray, then extract the two screws securing the trim panel at this location. 2. Pop out the two outside blank dummy switches located near the top of the trim panel, below the vents, then remove the single screw located behind each switch. 3. Pull the panel outward from along the bottom, then pull the panel down and away from the dash, ATTACH disconnect the harnesses and remove EXCEL USE the trim panel. SPACERS THESE 4. Remove the four screws securing the radio to the panel, disconnect the connectors and remove the radio.
LEFT SIDE
RIGHT SIDE USE THESE
ATTACH EXCEL SPACERS
FRONT OF PANEL 2029
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS AND DISCARD.
Read page 2 for kit assembly.
1986-89 Hyundai Excel (All Models) 1987-89 Mitsubishi Precis (All Models) RADIO REMOVAL: SHAFT-MOUNT RADIO REMOVAL: 1. Remove knobs from the radio. 2. Remove the shaft nuts and the radio face plate. 3. Remove (2) screws from each sid e of the radio. 4. Slide the radio out of the dash, disconnect wiring, and remove the radio.
PANEL 1541
DIN-TYPE RADIO REMOVAL 1. Place a small screwdriver into the slot on each side of the radio and pull the trim towards the rear of the car to release the trim snaps. Remove the trim and using the radio removal tools (available from the Hyundai dealer), slide the radio out of the cavity. Disconnect all wiring and remove the radio. 2. Extract the single screw from each side of the radio shroud (center screw of three). 3. Carefully pull on the edges of the radio/climate control trim panel to release snaps and remove panel. 4. Remove the (4) screws which secure the radio mounting shroud to the dash and remove the shroud. 5. Snap the radio/climate control trim panel back on to the dash (do not install the screws which hold the climate controls). USE THE SHADED BRACKETS & THE INDICATED SPACER.
Read page 2 for kit assembly.
1991-UP Hyundai Scoupe RADIO REMOVAL: 1. Remove the two sheet metal screws from the bottom of the radio trim bezel. 2. Carefully unsnap the trim bezel by prying outward with a panel removal tool. Unplug and remove all the connectors. 3. Extract the four sheet metal screws securing the radio to the dash. Unplug all the connectors and remove the radio.
PANEL 2029
LEFT SIDE
RIGHT SIDE
USE THESE
USE THESE
FRONT OF PANEL 2029
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS AND DISCARD.
3
Read page 2 for kit assembly.
1995-UP Hyundai Sonata RADIO REMOVAL:
PANEL 2364
1. Carefully pry up on the gear shifter trim bezel with a panel removal tool to release the clips and remove. 2. Extract the (1) screw at the bottom of the radio trim bezel. 3. Using a panel removal tool carefully pry out on the radio trim bezel to release the fastening clips, unplug all the connectors, and remove the bezel. LEFT SIDE 4. Extract the (6) screws securing the radio / pocket assembly to the dash, unplug all the connectors and remove.
RIGHT SIDE
USE THIS TAB
USE THIS TAB FRONT OF PANEL 2364
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS.
Read page 2 for kit assembly.
1989-94 Hyundai Sonata RADIO REMOVAL: 1. Extract the two screws from the inside walls of the dash pocket - one screw on each side. 2. Remove the plastic cover cap located at the top left side of the dash trim panel, extract the single screw from this location. 3. Release the trim panel, disconnect the connector from the defogger switch and remove the panel. 4. Extract the four screws securing the radio to the dash, pull the unit out of the cavity, disconnect the antenna cable/wire harness and remove the LEFT SIDE radio. USE NOTE: Flip kit panel for this application so THESE the brackets are at the front edge.
PANEL 2029
RIGHT SIDE USE THESE
FRONT OF PANEL 2029
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS.
1997-UP Hyundai Tiburon
Read page 2 for kit assembly.
RADIO REMOVAL: 1. Unscrew shift handle and remove. 2. Unsnap and remove shifter trim bezel. 3. For automatic, place car in Low, or for manual place shifter back in 4th gear. 4. Open ashtray, carefully pull back on Radio / console trim bezel to release, and LEFT SIDE disconnect lighter to remove. 5. Extract (4) screws securing radio, unplug and remove.
PANEL 2364
RIGHT SIDE
USE THIS TAB
USE THIS TAB FRONT OF PANEL 2364
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS.
4
