Transcript
I-CK-600
SPECIAL INSTRUCTIONS for SUNNEN® CK-6000 CE COVER KIT
http://www.sunnen.com
For Use on Sunnen® CK-21 Vertical Honing Machines
INTRODUCTION
4. Turn OFF all power to the Machine.
Sunnen®
CK-6000 CE Cover Kit is designed to be installed on Sunnen CK-21 Vertical Honing Machine to ensure they conform with CE safety standards.
5. Remove one screw on each side of machine’s A-Frame (refer Figure 1).
INTALLATION
6. Attach CE Cover to A-Frame using two screws removed in step 5 and hardward provided.
Read the following instructions carefully and thoroughly before installing the CE Cover (see Figure 1). 1. Assembly Frame (item’s 1, 3, & 6) using the hardware provided. 2. Attach Side Covers (item’s 4 & 5) to Frame.
7. Attach Cover Extension (item 14) to CE Cover as shown (see Figure 2). 8. Turn ON power to machine and check that Overarm clears Cover. Adjust as required.
3. Attach Rear Cover (item 2) to Side Covers.
#7 WASHER (6) #12 SCREW (6)
#2 REAR COVER
#14 COVER EXTENSION #10 NUT(6)
#4 CE COVER, LEFT EXISTING
#3 REAR CE BRACKET #9 SCREW (2)
#1 SWAYBAR (2)
#7 WASHER (2) #10 NUT(2) #5 CE COVER, RIGHT #11 SCREW (16)
#6 SUPPORT BAR (2) #13 WASHER (16)
A-FRAME A-FRAME
FIGURE 1 SUNNEN ®
PRODUCTS COMPANY • 7910 MANCHESTER AVENUE • ST. LOUIS, MO 63143, U.S.A. • PHONE: 314-781-2100
14 2 10 4
1
7
12
EXISTING
1
3 6 7
10
6
5 11 13 6
A-FRAME
Figure 2 Item #
1 2 3 4 5 6 7 8 9 10 11 12 13 14 -
Part No.
CK6001 CK6002 CK6003 CK6004 CK6006 CK6007 PHWM509 PHSM534 PHSM964 PHNM407 PHSM431 PHSM510 LBA451 CK6015 CK6016 CK6017
Qty.
2 1 1 1 1 2 18 4 2 14 16 12 16 1 -
Description
Swaybar Rear Cover Rear CE Bracket Left CE Cover Right CE Cover Support Bar Lockwasher (M6) Screw (M6 x 1,0 x 20mm SHCS) Screw (M6 x 1,0 x 35mm SHCS) Nut, Hex (M6 x 1,0) Screw (M5 X 0.8 X 10mm BHCS) Screw (M6 X 1.0 X 12mm BHCS) Lockwasher (#10) Cover Extension CE Cover Extension Standoff
“SUNNEN AND THE SUNNEN LOGO ARE REGISTERED TRADEMARKS OF SUNNEN PRODUCTS COMPANY.”
Sunnen® reserves the right to change or revise specifications and product design in connection with any feature of our products contained herein. Such changes do not entitle the buyer to corresponding changes, improvements, additions, or replacements for equipment, supplies or accessories previously sold. Information contained herein is considered to be accurate based on available information at the time of printing. Should any discrepancy of information arise, Sunnen recommends that user verify discrepancy with Sunnen before proceeding. PRINTED IN U.S.A.
0501
SUNNEN PRODUCTS LIMITED No. 1 Centro, Maxted Road Hemel Hempstead, Herts HP2 7EF ENGLAND Phone: ++ 44 1442 39 39 39 Fax: ++ 44 1442 39 12 12 www.sunnen.co.uk e-mail:
[email protected]
SUNNEN AG
SUNNEN PRODUCTS COMPANY 7910 Manchester Ave., St. Louis, MO 63143 U.S.A. Phone: 314-781-2100 Fax: 314-781-2268 U.S.A. Toll-Free Sales and Service – Automotive: 1-800-772-2878 • Industrial: 1-800-325-3670 International Division Fax: 314-781-6128
Fabrikstrasse 1 8586 Ennetaach-Erlen, Switzerland Phone: ++ 41 71 649 33 33 Fax: ++ 41 71 649 34 34 www.sunnen.ch e-mail:
[email protected]
SHANGHAI SUNNEN MECHANICAL CO., LTD. 889 Kang Qiao East Road, PuDong Shanghai 201319, P.R. China Phone: 86 21 5 813 3322 Fax: 86 21 5 813 2299 www.sunnensh.com e-mail:
[email protected]
SUNNEN ITALIA S.R.L.
http://www.sunnen.com e-mail:
[email protected]
Viale Stelvio 12/15 20021 Ospiate di Bollate (MI) Italy Phone: 39 02 383 417 1 Fax: 39 02 383 417 50 www.sunnenitalia.com e-mail:
[email protected]
©COPYRIGHT SUNNEN® PRODUCTS COMPANY 2005, ALL RIGHTS RESERVED
