Ibus Wall-dock For Distributed Audio With Rs-232 Control

Transcript

A0316 iBus Wall-Dock for Distributed Audio with RS-232 Control TM By 10 The A0316 is an on-wall iPod® docking station that supports RS-232 and IR control. The dock connector slides in and out to adjust for any iPod and the non-skid pad helps to hold the music player in place. Its elegant and contemporary design make the A0316 perfect for anyone who wants to enjoy their music without defacing their wall. Features: ! Supports IR control: compatible with A0505 or Apple Remote ! RS-232 interface for use with advanced control systems ! Built-in IR receiver ! Charges the iPod ! Allows viewing of iPod videos on a TV ! Mounts in a standard 2-gang box Wall Dock Front/Top Front/Bottom Hinged Dock Lid Rotates down to cover the dock connector Dock Connector Connects to iPod Non-Skid Pad Secures the iPod Sliding Dock Platform Slides up to conceal the dock connector Slide Up Sliding Dock Lever Slides the dock connector forward, providing easy access to dock your iPod RJ-45 & 110 Connectors Connect to output wall plate via CAT5 cable (only use one) Composite Video Output Outputs video signals from the iPod Use RG59U coax or CAT5 and a video balun (Suggested balun model B201 CAT5 video balun) 2 Output Wall Plate Back Front Audio Outputs Connect to your amplifier. RJ-45 & 110 Connectors Receive signals from the wall dock via Category 5 or Category 6 cable. ! Serial Connector ! RS-232 interface ! provides advanced ! control and feedback. ! IR Input ! Connect an IR receiver and use the A0505 remote to control your iPod. Installing the Trim Plate Accessory Install Output wall plate in j-box Snap trim into place Install Trim plate chassis over output wall plate Snap front cover over chassis Snap side flange on to front cover Compatibility Made For: ! ! iPod touch (2nd generation) iPod nano (4th generation) ! ! IPod touch (1st generation) iPod nano (3rd generation) ! ! iPod classic iPod nano (2nd generation) ! ! iPod video iPod nano (1st generation) ! ! iPod nano (5th generation) iPod mini ! iPod with dock connector 3 Basic Application A0316 Wall Dock Rear Front HDTV Plasma with speakers TV or Video Display Video Output A C N N EL V IS IO N R WE PO 1 H 2 S O L DE 5 MO 50 A0 U R 3 C E 4 2 1 NE R ZO WE PO A MER CA 4 3 TE MU V CAT L VO D MO A0505 Remote Control The built-in IR receiver allows the A0316 to be controlled directly by the A0505. CAT5 cable up to 350ft. Whole-House Audio System Rear Front Pwr. Serial Control Automation: Control4 driver available from Extravegetables.com IR receiver (optional) C HANNEL V ISION POWER MODEL A0505 1 S O U R C E 2 3 4 ZONE POWER CAMERA 1 2 3 4 CATV MUTE MOD VOL A0505 Note: An IR emitter output A0316 Output Wall Plate from a whole-house IR system Remote can also be connected here. As shown on the following page. 4 Sample Wiring Diagram: When used with the A4623 Connect an IR emitter output into the “IR in” of the A0316 output wall plate. Power supply not shown DVD player CD player IR-4180 POWER 115 IR Emitters 6 Control 5 4 Control 3 O U T P U T 5 6 R-AUDIO-L S P E A K E R O U T P U T S + R - - L + VIDEO + R - - L + 2 Control 1 O U T P U T O U T P U T 3 4 R-AUDIO-L VIDEO + R - - L + 1 Hi-Z 75 1234 + R - - L + R-AUDIO-L VIDEO 3 4 2 RG59U or RG6 1 VIDEO R-AUDIO-L C U ® VIDEO US ~ 230/115V 50/60 Hz MAX 115W Warning: + R - - L + A4623 To prevent fire or shock hazard do not expose this unit to rain or moisture. Tested To Comply With FCC Standards 5 1 I N P U 2 T 4 Channel Vision 6 Input Voltage 3 2 R-AUDIO-L + R - - L + Link Serial FOR HOME OR OFFICE USE CAUTION FUSE RISK OF ELECTRIC SHOCK DO NOT OPEN T3.15AL/250V 115VAC RG59U or RG6 A4623 Rear Panel TV or Video Display The single-gang trim plate can be used to hold a single-gang keypad next to the iPod dock in a 3-gang junction box. See installation section for details. CAT5 CAT5 IR signals detected by the A0127 keypad will be repeated back to the A4623. This allows control of the input sources. CHAN L MODE A0505 NEL POWER N 3 2 4 MUTE 1 S O 2 U R C 3 E 1 VOL V ISIO CAMERA MOD CATV ZONE POWER 4 5 Installing the Wall Dock Installation Steps 1. Connect all wiring. 2. Attach main chassis to j-box using the provided four 6-32 screws. 3. Feed the dock connector circuit board through the opening in the front cover. 4. Hang the front cover on the main chassis from the two top tabs. 5 5. Secure the front cover with the two small screws at the bottom. 6. Place the dock platform over 6 the slide rail and push downward until the retention snaps are engaged. 7. Slide the side protectors into the slots on the main chassis. 7 4 3 1 2 3 2 2 5 Slide Rail 6 Retention Snap Steps 3 & 4 complete Steps 5 & 6 complete Completed Installation 6