Transcript
Tech Spec
IC-80-J
Industrial Crane
18,000 lb Max. Capacity Available in 3 Boom Lengths
Rated Capacity Limiter ... Standard Capacity on Outriggers ... 18,000 lb Pick and Carry Capacity ... up to 11,700 lbs Height ... 7’ 3” Width ... 6’ 6” Boom Rotation ... 360 Degree Continuous Sheave Height ... up to 46’ Horizontal Reach ... up to 40’ 4-Wheel Steer ... Standard Powershift Transmission ... Standard Fully Hydraulic Controls for Smooth Precise Operations Independent Outrigger Controls Dual Fuel or Diesel Engine Available
Manufacturing Corp.
IC-80-J
Specifications GENERAL: Weight: 2-Wheel Drive
IC-80-1J 16,200 lb (7,350 kg)
IC-80-2J 16,400 lb (7,440 kg)
IC-80-3J 16,750 lb (7,600 kg)
Boom Movement: Continuous Continuous Continuous Rotation Elevation 0º to 70º 0º to 70º 0º to 70º Extension 12 ft. 14 ft. 6 in. 18 ft. 6 in. (366 cm) (442 cm) (564 cm) Boom Speeds: Rotation 2.0 RPM 2.0 RPM 2.0 RPM Elevation 10.0 sec. 10.0 sec. 10.0 sec. Extension 17.0 sec. 21.0 sec. 27.0 sec. Turning Radius: (C/L of Outside Steering Wheel) 11 ft. 2 in. (3.40 m) Aisle Width for 90º Turn: 9 ft. 7 in. (2.92 m) Gradeability: 63 percent (32 degrees) ENGINE: Dual Fuel Diesel Make GM Cummins Model 3.0 EFI* EPA Tier II B 3.3L EPA Tier IVi Type Gas Diesel No. Cyl. 4 4 Displacement 181 CID (3.0 L) 199 CID (3.3 L) HP @ Gov. Speed 59 (44kW) 74 (55kW) Electronic Fuel Injection with Dual Fuel, US EPA & CARB. Certified for 2012 emissions standards
Fuel Tank Capacity: 17.6 Gallons (66.6 L) TRANSMISSION: Powershift transmission with 4-speeds in forward & reverse. Provides powershifts at any engine speed in any gear. All shifting is done with a single lever electrical control mounted on the steering column. Multiple-disc clutch packs operated by solenoid valve provide forward, neutral, reverse and speed selection. Equipped with oil cooler and filter. Torque converter has stall ratio of 2.2:1. Transmission Forward Travel Speed Drawbar Pull1 Gear or Reverse MPH (km/h) Pounds (kg) First 5.72:1 4 (6) 15,500 (7,031) Second 3.23:1 7 (11) 8,700 (3,946) Third 1.77:1 13 (21) 4,600 (2,087) Fourth 1.00:1 22 (35) 2,500 (1,134) 1) Drawbar pull is calculated based on GM 3.0L gasoline engine.
AXLES: Front: Planetary drive/steer axle with 11.625:1 axle ratio. Differential is “No-Spin.” Axle mounted rigidly to frame. Rear: 2-Wheel Drive: Axle with 1-1/2° oscillation in either direction. STEERING: Hydraulic steering unit with cylinders attached to each axle. Rear axle is the primary steer. An electric switch in the operator’s commartment is used to select rear-wheel steering, four-wheel round steering or crab steering. Electronic sensors and control box automatically align the steering when a new mode is selected. BRAKES: Four-wheel hydraulic. Wet disc brakes are on the front and rear axles. Parking brake is disc type. TIRES: 2-Wheel Drive 10.00 x 15, load range H bias, 16-ply rating. CHASSIS: Cargo Deck: 53 square feet (5 m2) of deck area. A maximum of 14,000 lb (6,350 kg) capacity on deck when load is centered over or between axles.1 A storage box is located in front cargo deck. Steps located on front corners. Heavy deck loads allowed at creep speed below 2 MPH (3.2 km/h) and less than 200 feet (61 m) in 30 minutes.
Headlight and Taillight Grilles: Welded steel protective grilles for headlights and taillights. Outriggers: Four hydraulic outriggers of box beam construction. Independent controls for each outrigger. Each cylinder equipped with direct-connected holding valves. Outrigger pad dimension 9 inches (23 cm) x12 inches (30 cm). Lifting Rings: Lifting rings at each corner of cargo deck so sling can be attached for lifting crane. OPERATOR COMPARTMENT: Operator’s control station provides one-position access to all operating functions. Includes adjustable operator’s seat, retracting seat belt, fire extinguisher and bubble level. ELECTRICAL (12 Volt System): Instrument Package: Includes fuel gauge and hourmeter. Also included are warning lights for low oil and transmission pressure, turn signal, high beams, hazard lights, parking brake, hydraulic oil temperature, battery, check engine, stop engine, coolant temperature, outriggers. Lighting Package: One pair headlights with Hi and Low beams, back-up lights, integral tail, brake, front and rear turn signals and emergency flasher switch at operator’s station. 12V horn actuated by button on shifting control. Back-Up Alarm: Provides pulsating sound from 97 dB alarm when transmission is in reverse. Conforms to SAE J994b. Outrigger Alarm System: Two-tone alarm is activated when “outrigger down” controls are operated. HYDRAULIC SYSTEM: Tandem pump, direct-driven by engine crankshaft, rated at 16 & 32 GPM at rated RPM (61 L/min & 121 L/min). Hydraulic oil tank capacity of 25 gallons (95 L). BOOM ASSEMBLY: Three-section boom assembly equipped with bearing pads, double-acting hydraulic cylinders with direct-connected holding valves & boom angle indicator on each side of boom. Boom Rotation: Heavy-duty ball bearing rotation gear with external teeth. Rotation is powered by hydraulic motor and worm gear drive. Boom Hoist: Turret mounted planetary gear hoist hydraulically powered with a bare-drum line pull of 10,000 lbs (4,536 kg) at a speed of 110 FPM (34 m/min). Includes downhaul weight, swivel hook & sheave block for 2-part line and 125 ft (38 m) of 9/16” (14 mm) hoist rope. Anti-Two-Block Device: Prevents damage to hoist rope and/or crane components from pulling load hook against tip. Sheave Block, Two-Part: Single sheave block for 2-part line requirements. Rated Capacity Limiter: Warns operator of impending overload with audible and visual signals. Prevents overload by stopping boom functions that cause overloads. Drum Rotation Indicator: Provides tactile feedback to operator when hoist drum is rotating.
IC-80-1J
IC-80-2J
IC-80-3J
IC-80-J Options
Listed below are brief descriptions of options available for this product. Consult the IC-80-J Engineering Spec for additional information. MODELS: IC-80-1J Industrial Crane with 8’2” (2.5 m) - 20’2” (6.1 m) Boom Reach IC-80-2J Industrial Crane with 9’6” (2.9 m) - 24’ (7.3 m) Boom Reach IC-80-3J Industrial Crane with 11’6” (3.5 m) - 30’ (9.1 m) Boom Reach
CHASSIS OPTIONS: Auxiliary Winch: Mounted behind front bumper, hydraulically driven with control in operator’s console. Pintle Hook: Pintle Hook, Rear Pintle Hook, Front Rearview Mirrors: One mounted on right-hand deck stake and one mounted on left-hand deck stake.
ENGINE: Spark Arrester Muffler: Installed in addition to std. muffler. OPERATOR COMPARTMENT OPTIONS: Catalytic Converter: Operator Guard: Reduces engine emissions. Tubular steel weldment with heavy Engine Heater: expanded steel mesh top section. Engine coolant heater installed to circulate Operator Guard Cover: warm water through engine. Plugs into120 Clear vinyl cover which goes over Operator volt AC. 1,500 watts. Guard, for inclement weather operations. TIRE OPTIONS: All-Weather Cab: Mining & Industrial Tires: Rigid-mounted canopy section & removable 36 x 11-15, 16-Ply Rating hinged door. Includes heater, electric 36 x 11-15, Non Marking windshield wiper, one sliding glass window Solid Rubber Tires, 8.25 x 15 in the door & one in the right side of canopy. Foam Filling of Tires Defroster fan & dome light included. Spare Tire & Wheel: Cab Heater: Bias 10.0 x 15 Heater with two-speed fan for units without Mining & Industrial, 36 x 11-15 All-Weather Cab. Mining & Industrial, Non Marking Windshield Washer: Includes reservoir pump and nozzle. Floor Mat: Vinyl mat with foam backing. Deluxe Seat: Deluxe Seat with upholstery springs provides additional operator comfort. Noise Reduction Kit: Includes floor mat, control valve and side panels of foam backed vinyl for noise reduction. Air Conditioning: Air Conditioner with R134 coolant.
ELECTRICAL OPTIONS: Strobe Lights: Yellow strobe light mounted on each side of turret weight box. Boom Work Lights: One work light mounted to boom to light boom tip and one work light mounted to turret to light ground under boom tip. Work Lights-Rear: Two work lights recessed in rear bumper. BOOM ATTACHMENTS: Boom Extension, 10 Foot (3 m): Boom stowable. Boom Extension, 10 Foot (3 m) Offsettable: Same as above item, except the boom extension is offsettable to 3 different positions; 0 degrees (inline), 15 degrees and 30 degrees offset. Searcher Hook: Nose Mount
Should you require an option or special equipment not listed please consult your dealer salesperson or BMC®.
Manufacturing Corp. PO Box 14770 Lenexa Kansas 66285
Tel (913) 888-0606 Fax (913) 888-8431 www.broderson.net
© 2011, Broderson Manufacturing Corp.
Dimensions and values shown are for reference purposes only. Specifications subject to change. Form #CC111J (11/11)
