Transcript
ICM 516
ICM 516
SURGE PROTECTOR ELECTRICAL SHOCK HAZARD – Before installing this unit, turn off power at the main service panel by removing the fuse or switching the appropriate circuit breaker to the OFF position.
SPECIFICATIONS AC Protection Modes: L-L, L-G Size: 4.8” X 2.75” X 1.69” Weight: 0.55 lbs.
Service Voltage: 120/240 Volt Single Phase Maximum Surge Current: 100,000 Amps Maximum Energy Dissipation: 1,400 Joules Installation Point: Electrical Panel, Electrical Disconnect Diagnostics: Green light indicates surge suppression present
AC Protection Modes: L-L, L-G Size: 4.8” X 2.75” X 1.69” Weight: 0.55 lbs.
A/C DISCONNECT INSTALLATION
7313 William Barry Blvd. North Syracuse, NY 13212
800.365.5525 LII360
ICM CONTROLS www.icmcontrols.com
7313 William Barry Blvd. North Syracuse, NY 13212
SPECIFICATIONS
ICM 516 LII360
ICM 516
SURGE PROTECTOR ELECTRICAL SHOCK HAZARD – Before installing this unit, turn off power at the main service panel by removing the fuse or switching the appropriate circuit breaker to the OFF position.
GRN
800.365.5525
ICM 516
SURGE PROTECTOR ELECTRICAL SHOCK HAZARD – Before installing this unit, turn off power at the main service panel by removing the fuse or switching the appropriate circuit breaker to the OFF position.
SPECIFICATIONS AC Protection Modes: L-L, L-G Size: 4.8” X 2.75” X 1.69” Weight: 0.55 lbs.
Service Voltage: 120/240 Volt Single Phase Maximum Surge Current: 100,000 Amps Maximum Energy Dissipation: 1,400 Joules Installation Point: Electrical Panel, Electrical Disconnect Diagnostics: Green light indicates surge suppression present
A/C DISCONNECT INSTALLATION
7313 William Barry Blvd. North Syracuse, NY 13212
GRN
800.365.5525 LII360
ICM CONTROLS www.icmcontrols.com
7313 William Barry Blvd. North Syracuse, NY 13212
GRN
Ground Bus
BLK
BLK
GRN
Ground Bus
BLK
BLK
Keep the surge protection wires as short as possible to increase the response time and effectiveness. 1. Turn off main breaker. Neutral 2. Remove the front cover from the electrical panel. Bus 3. Remove a knockout from the electrical panel. 4. Mount the unit through the knockout to the side of the electrical panel. 4.1 Remove the retaining ring on the unit. 4.2 Feed the wires into the electrical panel. 4.3 Re-secure the retaining ring. 5. Route the green wire to the grounding lug and secure. 6. Connect the two black wires to the closest two-pole breaker. 7. Close cover on the panel.
ICM 516
ELECTRICAL PANEL INSTALLATION ICM 516
ELECTRICAL PANEL INSTALLATION Keep the surge protection wires as short as possible to increase the response time and effectiveness. 1. Turn off main breaker. Neutral 2. Remove the front cover from the electrical panel. Bus 3. Remove a knockout from the electrical panel. 4. Mount the unit through the knockout to the side of the electrical panel. 4.1 Remove the retaining ring on the unit. 4.2 Feed the wires into the electrical panel. 4.3 Re-secure the retaining ring. 5. Route the green wire to the grounding lug and secure. 6. Connect the two black wires to the closest two-pole breaker. 7. Close cover on the panel.
The unit can be installed at the main breaker panel or the service disconnect for the A/C condenser. ICM recommends installation at the service disconnect for the A/C condenser. Keep the surge protection wires as short as possible to increase the response time and effectiveness. 1. Turn off the main power to the service disconnect. 2. Remove the cover on the service disconnect. 3. Remove a knockout from the service disconnect. Ground Bus 4. Mount the unit through the knockout to the side of the service disconnect. 4.1 Remove the retaining ring on the unit. 4.2 Feed the wires into the service disconnect. 4.3 Re-secure the retaining ring. 5. Route the green wire to the grounding lug and secure. 6. Connect the two black wires to the disconnect power terminals. 7. Close cover on the service disconnect.
ICM 516
ICM 516
GRN
BLK
BLK
The unit can be installed at the main breaker panel or the service disconnect for the A/C condenser. ICM recommends installation at the service disconnect for the A/C condenser. Keep the surge protection wires as short as possible to increase the response time and effectiveness. 1. Turn off the main power to the service disconnect. 2. Remove the cover on the service disconnect. 3. Remove a knockout from the service disconnect. Ground Bus 4. Mount the unit through the knockout to the side of the service disconnect. 4.1 Remove the retaining ring on the unit. 4.2 Feed the wires into the service disconnect. 4.3 Re-secure the retaining ring. 5. Route the green wire to the grounding lug and secure. 6. Connect the two black wires to the disconnect power terminals. 7. Close cover on the service disconnect.
BLK
A/C DISCONNECT INSTALLATION
AC Protection Modes: L-L, L-G Size: 4.8” X 2.75” X 1.69” Weight: 0.55 lbs.
BLK
Service Voltage: 120/240 Volt Single Phase Maximum Surge Current: 100,000 Amps Maximum Energy Dissipation: 1,400 Joules Installation Point: Electrical Panel, Electrical Disconnect Diagnostics: Green light indicates surge suppression present
www.icmcontrols.com
GRN
BLK
Ground Bus
Keep the surge protection wires as short as possible to increase the response time and effectiveness. 1. Turn off main breaker. Neutral 2. Remove the front cover from the electrical panel. Bus 3. Remove a knockout from the electrical panel. 4. Mount the unit through the knockout to the side of the electrical panel. 4.1 Remove the retaining ring on the unit. 4.2 Feed the wires into the electrical panel. 4.3 Re-secure the retaining ring. 5. Route the green wire to the grounding lug and secure. 6. Connect the two black wires to the closest two-pole breaker. 7. Close cover on the panel.
BLK
GRN
BLK
BLK
Ground Bus
ICM 516
ELECTRICAL PANEL INSTALLATION
Keep the surge protection wires as short as possible to increase the response time and effectiveness. 1. Turn off main breaker. Neutral 2. Remove the front cover from the electrical panel. Bus 3. Remove a knockout from the electrical panel. 4. Mount the unit through the knockout to the side of the electrical panel. 4.1 Remove the retaining ring on the unit. 4.2 Feed the wires into the electrical panel. 4.3 Re-secure the retaining ring. 5. Route the green wire to the grounding lug and secure. 6. Connect the two black wires to the closest two-pole breaker. 7. Close cover on the panel.
ICM CONTROLS
BLK
ICM 516
ICM 516
GRN
BLK
BLK
ELECTRICAL PANEL INSTALLATION
The unit can be installed at the main breaker panel or the service disconnect for the A/C condenser. ICM recommends installation at the service disconnect for the A/C condenser. Keep the surge protection wires as short as possible to increase the response time and effectiveness. 1. Turn off the main power to the service disconnect. 2. Remove the cover on the service disconnect. 3. Remove a knockout from the service disconnect. Ground Bus 4. Mount the unit through the knockout to the side of the service disconnect. 4.1 Remove the retaining ring on the unit. 4.2 Feed the wires into the service disconnect. 4.3 Re-secure the retaining ring. 5. Route the green wire to the grounding lug and secure. 6. Connect the two black wires to the disconnect power terminals. 7. Close cover on the service disconnect. BLK
A/C DISCONNECT INSTALLATION The unit can be installed at the main breaker panel or the service disconnect for the A/C condenser. ICM recommends installation at the service disconnect for the A/C condenser. Keep the surge protection wires as short as possible to increase the response time and effectiveness. 1. Turn off the main power to the service disconnect. 2. Remove the cover on the service disconnect. 3. Remove a knockout from the service disconnect. Ground Bus 4. Mount the unit through the knockout to the side of the service disconnect. 4.1 Remove the retaining ring on the unit. 4.2 Feed the wires into the service disconnect. 4.3 Re-secure the retaining ring. 5. Route the green wire to the grounding lug and secure. 6. Connect the two black wires to the disconnect power terminals. 7. Close cover on the service disconnect.
www.icmcontrols.com
ELECTRICAL SHOCK HAZARD – Before installing this unit, turn off power at the main service panel by removing the fuse or switching the appropriate circuit breaker to the OFF position.
SPECIFICATIONS
Service Voltage: 120/240 Volt Single Phase Maximum Surge Current: 100,000 Amps Maximum Energy Dissipation: 1,400 Joules Installation Point: Electrical Panel, Electrical Disconnect Diagnostics: Green light indicates surge suppression present
ICM CONTROLS
SURGE PROTECTOR
800.365.5525 LII360
