Igigaswitch 16xx E+ Family

Transcript

iGigaSwitch 16XX E+ family Managed industrial Ethernet switches 16 port switches family • • • • Up to 12x PoE+ ports according to IEEE 802.3at with 360W budget Models with12x, 8x 6x or 4x SFP ports HSR switches model Extensive diagnostics functionality LANactive Industry More about the solution for mission critical applications: www.nexans.com/LANsystems Application Nexans iGigaSwitch 16xx E+ family presents full gigabit industry grade managed DIN-rail mounted switches designed to ensure extremely high reliability and long lifespan in harsh environments of different mission critical applications. Those switches are targeted to provide highest network availability, security and to make network maintenance much easier. Nexans iGigaSwitch 16xx E+ family provides high flexibility in network design – they have up to 16 ports: fibre-optic or copper in different com- binations, including the variant with 12x SFP and 4x RJ45 ports. The switches allows to adapt the interfaces to the application by using the corresponding pluggable modules (Fast Ethernet or Gigabit SFP). I/O Interfaces (optional) I/O interfaces allow a fast, simple and low-cost integration of additional non-Ethernet devices directly in the field. The switches are offering extensive management functionalities with interactions, sending of messages as well as the activation of alarms. Power over Ethernet+ (optional) Up to 12 connected users can be supplied with Power over Ethernet. In accordance with the latest IEEE 802.3at (PoE+) standard, up to 25.5 watts of power are available for each connected device (360W budget). IEC 61850 compliance Nexans iGigaSwitch family enable an intelligent communication environment for Smart Grids supporting the IEC 61850 standard (parts 6, 7-1, 7-2, 7-3, 7-4, 8-1, 9-1 and 9-2 Communication networks and systems for power utility automation). Features General • 16 Port Switch • up to 12x Vario-SFP ports • 10/100/1000 Mbps • Support of Jumboframes • -40°C ... +85°C (Operation) • HSR model is available • IEC 61850 standard compliance (parts 6, 7-1, 7-2, 7-3, 7-4, 8-1, 9-1 and 9-2) I/O Interfaces (optional) • 4x potential-free function inputs and 2x programmable alarm contacts Memory card (optional) • Memory card with MAC-Address • System Configuration and fimware backup on Memory Card and boot up with Memory Card MAC address and Configuration Redundant Power Supply • Two redundant Wide Range Power Supply Inputs (18 VDC ...72 VDC) Energy Management • Low Power Design (typ. 15 Watts) Twisted Pair User Interfaces • up to 12x RJ45 user interfaces (10/100/1000 Mbit/s) • MDI/MDI-X Auto-Crossover and Auto-Polarity Mechanic • Ruggedized design without vents and holes • Compact design (95mm x 184mm x 125mm) www.nexans.com/LANsystems • Power over Ethernet+ (optional) • up to 12x Power over Ethernet (PSE+) according to IEEE 802.3at Management • WEB/SNMP/SSH/V.24 Management • Hardened management, corruption impossible • LLDP and CDP • Compatibility to “Cisco Identity Services Engine ISE“ • Extensive security functions SCP, SSHv2, HTTPS, RADIUS, SNMPv3, IEEE802.1X etc. • Integrated in ARP Guard Secure Management • Configuration via NexMan (administration tool) • IPv6 according to IPv6 Forum phase 2 core specification [email protected] Technical data iGigaSwitch 16xx E+ family Version Order numbers iGigaSwitch 1604 E+ SFP-4VI PRO3 iGigaSwitch 1606 HSR SFP-6VI PRO4 iGigaSwitch 1608 E+ SFP-8VI PRO3 iGigaSwitch 160C E+ SFP-12VI PRO3 88306400 88306406 88306408 88306412 88301602 Memory card with MAC address 88300692 Memory card with MAC address and MRP Multi licence 88300694 iOption PoE Type at 4-30 88301602 88301602 88301602 iOption PoE Type at 8-30 88301604 88301604 88301604 - iOption PoE Type at 12-30 88301606 - - - I/O module digital 4xIn 2xOut 88301600 RJ45 serial cable for iGigaSwitch 88646169 LAN Interfaces Twisted Pair interfaces (RJ45) SFP interfaces 12x 10/100/1000 Mbps 10x 10/100/1000 Mbps 8x 10/100/1000 Mbps 4x 10/100/1000 Mbps 4x 100/1000 Mbps 4x 100/1000 Mbps 8x 100/1000 Mbps 12x 100/1000 Mbps - 2x 100/1000 Mbps - - SFP interfaces HSR in connection with PoE options Power over Ethernet (optional) Number of RJ45 ports with PoE+ Max. PoE power output max. 12x PoE+ - max. 8x PoE+ max. 4x PoE+ 360 Watt - 240 Watt 120 Watt Diagnostic functions (Interfaces) Digital Diagnostic Monitoring interface Yes Twisted Pair cable diagnostic Pending General Housing Anodised / varnished aluminium case Color Mounting Black 35mm DIN-Rail Mounting accoring to EN 60715, (EN50022), different positions of DIN-rail clip, optional: wall mounting Dimensions [WxHxD] 95 mm x 184 mm x 125 mm IP degree of protection IP 30 (EN 60529) Ambient temperature Operation: -40 ... +85 °C, Storage: -40 ... +85 °C Relative humidity 20 - 90 % (non-condensing) Weight MTBF 1800g >500.000 h >500.000 h >500.000 h >500.000 h BTU Power suppy Input voltage for switch min. 18 / tipical 24 / max. 72 VDC Input voltage for PoE+ min. 46 / tipical 54 / max. 57 VDC Power consumption without PoE+ min. 13 / tipical 15 / max. 28 W Interface connector for power source 2x 3-pin terminal block, screw-on type Separate PoE input Yes Interface connector for PoE Source 3-pin terminal block, screw-on type I/O Adapter - Alarm contacts - Function inputs (optional) I/O interface connector (optional) 16-pin teminal block (screw-on type) Number of outputs 2x independent outputs (Changer function) Current/Voltage of Output contacts 2A / 30V DC Auxiliary voltage sorurce 24V DC /max. 42mA / For support of digital contacts Number of digital inputs 4x Input Voltage of input contacts 12 - 60V DC Dry contacts support Yes / Via auxiliary voltage provided by the switch Functional parameters Firmware Type Data throughput PRO3 PRO4 PRO3 > 1.488.000 Pakete/Sek. per Port (FDX, bidirectional) Switching method Store and forward, self-lerning Max. Framesize 9.600 bytes (Support of Jumboframes) Paket Buffer 512 kByte Max Frame Length 10/100/1000 Mbit/s 9000 Max MTU Length 10/100/1000 Mbit/s 9582 Backplane capacity 50 GBit/sec 100Mbit/s 64Byte: 9µs / 3,9µs 100Mbit/s 1518Byte: 125µs / 4µs 1Git/s 64Byte: 2,7µs / 2,2µs 1Gbit/s 1518Byte: 15µs / 2,5µs Latency time (FIFO/LIF0) www.nexans.com/LANsystems • [email protected] PRO3 Technical data iGigaSwitch 16xx E+ family Version iGigaSwitch 1604 E+ SFP-4VI PRO3 iGigaSwitch 1606 HSR SFP-6VI PRO4 iGigaSwitch 1608 E+ SFP-8VI PRO3 iGigaSwitch 160C E+ SFP-12VI PRO3 On-Board High-Performance Management Management Memory Firmware update Update in separate FLASH area, Corruption impossible FLASH Configuration Dual Configuration, Corruption impossible Secure management protocols SCP, SSH, HTTPS, SNMPv3 Passwort Strength Checker Yes Configuration reset button Yes (Configuration button deactivatable) SD memory card with fixed MAC-Address for redundant storage of the complete switch configuration and firmware (optional) Memory Card Console Interface Yes (Cisco like) Standards Electrical safety (IT equipment) EN 60950 Electrical conditions (EMC) EN 55022 IEC 61850-6, 7-1, 7-2, 7-3, 7-4, 8-1, 9-1 and 9-2 IEC 61850 Certificate Level A IEC 61850 SERVER functionality - MMS and GOOSE KEMA certified Communication networks and systems for power utility automation General environmental requirements for hardware design IEC 61850-3 Environmental Standards for Networking Devices Installed in Power Utility Substations IEEE 1613 Immunity for industrial environments IEC 61000-6-2 Adjustable speed electrical power drive systems Redundancy protocols Others (abstract) IEC 61800-3 STP, RSTP, MSTP (pending), MRP HSR STP, RSTP, MSTP (pending), MRP STP, RSTP, MSTP (pending), MRP STP, RSTP, MSTP (pending), MRP CE, IEEE 802.3x (Flow Control), IEEE 802.1AB (LLDP), IEEE 802.1D (MAC Bridges), IEEE 802.1D (Rapid Spanning Tree Protocol), IEEE 802.1D (Class of Service), IEEE 802.1X (Port-Based Network Access Control) ANSI/TIA-1057 (Link Layer Discovery Protocol for Media Endpoint Devices), ISO/IEC 15802-3 (Media Access Control Bridges), IEC 62439-2 (Media Redundancy Protocol-MRP) 184mm 193mm Dimensions 125mm 139mm 95mm www.nexans.com/LANsystems • [email protected] Management Features (Extract) iGigaSwitch 16xx E+ family Access Control / Authentication Management 5 admin account with Read/Write access for HTTP/HTTPS, Telnet/SSH/V.24 console and NexMan Access Policy Mode with disabling function for unsecure protocols, activation of SSHv2, HTTPS, SNMPv3 and „Password Checker“ Gratuitous ARP function guarantees that the switch can be reached after change of IP address Securely encrypted transfer of configuration und firmware via SCP- Secure Copy IPv6 according to IPv6 Forum phase 2 core specification WEB / HTTP / HTTPS Access WEB interface (no proxy server required) TCP port number can be set for WEB access Telnet / SSH and V.24 Console Telnet console (no proxy server required) and Cisco-like command line interface SSH/Telnet or V.24 console can be disabled respectively SSH/Telnet and V.24 console authentication via RADIUS server Secure 256-bit encrypted SSH / SSL transfer and use of 1024-bit RSA keys SNMP Access, SNMP Traps and Syslog Messages Configuration of switch possible via “SNMP Set Request“ MIB-II (RFC1213) system, interface, at, ip ETHERLIKE MIB (RFC2665) dot3StatsTable IF-MIB (RFC2863) ifXTable BRIDGE-MIB (RFC4188) dot1dBase, dot1dStp, dot1dTp RSTP-MIB (RFC4318) RMON-MIB (RFC2819) statistics Eight IP addresses can be set as event receivers for SNMP traps, Alarm and Syslog messages Up to 27 different event types can be enabled per receiver Portsecurity Loop/broadcast limiter for protection against accidental or malicious packet storms Active loop protection with automatic disablement of short-circuited ports Manual definition of three authorized MAC addresses per port Automatic learning of up to three authorized MAC addresses per port Port switches off, when an unauthorized MAC address is detected SNMP trap/syslog message for newly detected or for unauthorized MAC address Transparent transmission of IEEE802.1x packets can be enabled/disabled RADIUS authentication of up to three MAC addresses per port Port authentication according to IEEE802.1x in connection with the RADIUS server Unauthenticated ports are switched into a freely selectable Unsecure-Default-VLAN VLAN Support / Trunking VLAN table selectable with up to 256 VLAN IDs, static or dynamic configurable Default-VLAN ID can be set for each port Default-VLAN can be disabled for trunking ports Trunking with tagging in accordance with IEEE802.1q can be enabled/disabled for each port Prioritization of the VLAN tags selectable according to IEEE802.1p Prioritization Prioritization selectable per each port according to IEEE802.1p / IPv4 and IPv6 Four output queues selectable for prioritization weighting per port 4 Prioritization scheme {strict queuing}, {8,4,2,1 weighted fair queuing} , {3 strict/2,1,0 weighted}, {2,3 strict/1,0 weighted} Discovery Protocols LLDP (Link Layer Discovery Protocol) CDP (Cisco Discovery Protocol) Switch Information / Configuration Configuration of IP parameters via DHCP and manual configuration of IP parameters possible Configuration of IP parameters possible without pressing configuration switches (NexCon) Loading of a Switch Configuration or firmware via Telnet/SSH/V.24/DHCP/BOOTP console possible Output of the running configuration in Telnet as CLI script and optional saving on an external TFTP server. Firmware and Configuration Management via Nexans Switch Manager Prevention of corruption through firmware update in separate FLASH segment Avoid corruption of configuration changes with dual configuration management NexMan authentication via RADIUS server Download / upload of the configuration and archiving in a database on the PC Upload of a new configuration into the switch is made On-The-Fly (no reboot required) Archiving of the configuration in an offline database (using NexMan) Securely encrypted configuration via SNMPv3 Link Aggregation LACP Redundancy RSTP - Rapid Spanning Tree Protocol MSTP - Multiple Spanning Tree Protocol Power over Ethernet Detection, monitoring and display of PoE related values, voltage and consumption 5 different modes: Power Setup, Off / On / Auto - 802.3af / Auto 802.3af High-Power /Auto 802.3at High-Power Environment Diagnose/Monitoring/Mirroring Display of internal operating voltages and housing temperature SNMP trap/alarm and syslog messages, if temperature is exceeded Logbook for permanent internal saving of syslog messages 35 counters for packets, bytes, Unicasts, Broadcasts, etc. per port Port monitor for individual ports Switch can be set to VLAN mirroring Display of SFP Information: Vendorname, Part Number, Serial Number, Datecode, etc. Display of SFP Diagnostics: TX and RX power in uW and dBm, temperature, voltage, bias current Configurable Alarm limits for TX- and RX-Power as well as for Laser-Bias-Current SNMP-Trap/Syslog-message activation for preset alarm limits Other Network Protocols IGMP Snooping (Internet Group Management Protocol) can be activated globally, IGMP protocol versions 1 or 2 can be selected SNTP (Simple Network Time Protocol) can be activated globally www.nexans.com/LANsystems • [email protected] • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • Pending • Pending • • • • • • • • • • • • • • Accessories iPowerSupplies – Nexans industrial power supplies • • • • Easy installation on the DIN-rail or wall Maximum energy efficiency thanks to low idling losses Models with startup temperature > -40°C Overload and short circuit-/no-load protection NOMINAL OUTPUT VOLTAGE OUTPUT VOLTAGE POWER OUTPUT AC INPUT VOLTAGE RANGE Nexans iPowerSupply S 115-230VAC/24VDC 30W 24V DC 24 30W 85...264V AC 88645963 Nexans iPowerSupply S 110-230VAC/24VDC 100W 24V DC 22.5-29.5 100W 85...264V AC 88646182 Nexans iPowerSupply S 115-230VAC/48VDC 60W 48V DC 48 60W 85...264V AC 88645960 Nexans iPowerSupply S 115-230VAC/48VDC 100W 48V DC 30…56 100W 85...264V AC 88646250 Nexans iPowerSupply S 115-230VAC/48VDC 240W 48V DC 30…56 240W 85...264V AC 88646072 Nexans iPowerSupply S 115-230VAC/48VDC 500W 48V DC 30…56 500W 85...264V AC CODE NAME 88646181 DC INPUT VOLTAGE RANGE 95...250V DC 95...250V DC SFP modules • • • • • • Gigabit and Fast Ethernet SFP modules Dual and single fibre variants Digital Diagnostic Monitoring Interface to readout specific parameters (e.g. temperature, optical input/output power) Wide operation temperature range: from -40°C up to +85°C Copper and E1 SFP modules are available Other modules, including vendors compatible versions are available upon request FIBRE TYPE WAVELENGTH TYP., NM (TX/RX) TYP. LINK RANGE M OPTICAL BUDGET MIN, DB MM, Dual fibre 1310/1310 2.000 12 Nexans SFP 100 Transceiver SM(LC)E L10 SM, Dual fibre 1310/1310 10.000 16 Nexans SFP 1000 Transceiver GI(LC)E MM, Dual fibre 850/850 550 9 88646016 Nexans SFP 1000 Transceiver SM(LC)E L10 SM, Dual fibre 1310/1310 10.000 12 88646017 Nexans SFP 1000 Transceiver SM(LC)E L40 SM, Dual fibre 1310/1310 40.000 19 88646018 Nexans SFP 1000 Transceiver SM(LC)E L80 SM, Dual fibre 1550/1550 80.000 24 88646019 Nexans SFP 1000 Transceiver SM(LC)E L120 SM, Dual fibre 1550/1550 120.000 29 88646073 Nexans SFP 1000 Transceiver SF3(LC)E L10 SM, Single fibre 1310/1550 10.000 12 88646075 Nexans SFP 1000 Transceiver SF5(LC)E L10 SM, Single fibre 1550/1310 10.000 12 88646133 Nexans SFP 1000 Transceiver SF3(LC)E L40 SM, Single fibre 1310/1550 40.000 19 88646135 Nexans SFP 1000 Transceiver SF5(LC)E L40 SM, Single fibre 1550/1310 40.000 19 88646226 Nexans TP SFP Transceiver 10/100/1000 Base-T RJ45 N.A. 100 N.A. 88646279 Nexans E1/T1 SFP Module RJ45 N.A. 1500 N.A. CODE NAME 88646010 Nexans SFP 100 Transceiver GI(LC)E 88646011 88646015 www.nexans.com/LANsystems • [email protected] Accessories NEXMAN device manager • • • • • • • • CODE Easy, intuitive and comfortable solution for centralised network configuration and management Auto discovery functionality Live device monitoring Master configuration functionality Integration into higher level management systems Client-Server capability Alarm management and logging Simultaneous firmware update for hundred of devices NAME - NEXMAN Device Manager, Evaluation Version 88301908 NEXMAN Device Manager, Single Licence 88301909 NEXMAN Device Manager, Company Licence Memory cards for industry switches • • • • Redundant encrypted storage (AES256) for industrial switches Switches stores its complete and most actual configuration and firmware automatically Using memory cards with MAC-address makes network maintenance processes much easier Two variants of memory cards: with MAC-address or with MAC-address and MRP multi license CODE NAME 88300692 Nexans SD Memory Card for iGigaSwitch with MAC-Address 88300694 Nexans SD Memory Card for iGigaSwitch with MAC address and MRP-Multi licence • • • CODE NAME 88646169 Nexans RJ45 console cable for iGigaSwitch family The V.24 console port on Nexans switches allows to configure the switch on site and/or to retrieve its status without an Ethernet network connection Configuration via the V.24 console port provides the same functionality as configuration via Telnet or SSH USB to Serial converter “Digitus DA-70156 USB to Serial Converter USB 2.0” or similar is recommended for PC‘s without DB-9 serial connector Nexans Deutschland GmbH • Advanced Networking Solutions Bonnenbroicher Str. 2-14 • 41238 Moenchengladbach • Tel +49 (0) 2166 27-2220 • Fax +49 (0) 2166 27-2499 E-Mail: [email protected] • www.nexans.com/LANsystems Copyright © Nexans 2017 - Subject to change without prior notice - kd-01168e05 Console configuration cables