Ijet-nav-pro

Transcript

iJet-Nav-Pro Date: 09-15-10 Table of Content Introduction .......................................................................................................................................... 2 Before Using the iJet-Nav-Pro ............................................................................................................. 2 Charging the iJet-Nav-Pro Remote Control......................................................................................... 3 Remote Control Wheel Pad ................................................................................................................. 4 iPods Compatible with the iJet-Nav-Pro ............................................................................................. 4 The iPhone ........................................................................................................................................... 5 Waiting for iPod Message.................................................................................................................... 5 Display Main Menu ............................................................................................................................. 5 The “Play/Pause” Sub-Menu ............................................................................................................... 5 The “Playlists” Sub-Menu ................................................................................................................... 6 The “Artists” Sub-Menu ...................................................................................................................... 7 The “Songs” Sub-Menu ....................................................................................................................... 7 The “Settings” Sub-Menus – Shuffle................................................................................................... 8 The “Settings” Sub-Menus – Display Timer ....................................................................................... 8 The “Settings” Sub-Menus - EQ .......................................................................................................... 9 The “Settings” Sub-Menus - Now Playing Mode ................................................................................ 9 The “Settings” Sub-Menus- Select iPod Mode.................................................................................... 9 The “Settings” Sub-Menus - About ................................................................................................... 10 The “Tech Support” Sub-Menus........................................................................................................ 11 The Sleep Mode ................................................................................................................................. 11 The Hidden Reset button ................................................................................................................... 11 www.buyijet.com 1 iJet-Nav-Pro Date: 09-15-10 Introduction Thank you for your purchase of the iJet-Nav-Pro. This is the NAVigation version of the PROfessional top of our line 2 way wireless iPod control products offered by BuyiJet.com. Please read and follow the instructions in this manual before using the product for the first time. Figure 1 – Product Components Before Using the iJet-Nav-Pro • • • • Plug the power charger into 100vac to 240vac power source, wall outline. Plug the opposite end of the power cable into the “5V DC” power input on the back side of the iJet-Nav-Pro dock. See picture below point B. Place the iJet-Nav-Pro remote unit into the charging slot on the dock. See Figure 3 below. Snap the support carriage into the iPod docking slot. This will support the iPod while docked. The slide on the carriage allows you to better position the support point. Figure 2 – Rear View A) USB connection for iTunes downloads etc. B) Power cable connection 5 VDC mini female plug. C) Audio cable connection 3.5 mm stereo jack. www.buyijet.com 2 iJet-Nav-Pro Date: 09-15-10 Charging the iJet-Nav-Pro Remote Control The remote control unit should always be stored plugged into the dock so it will stay charged. The battery performance can be maximized by always returning the remote to the docking carriage for charge. In order for the remote to charge via the iJet-Nav-Pro dock, the power cube must be plugged into a wall outline and the other end connected to the 5VDC input on the rear of the docking unit. While not in use, place the remote back into the remote charging cradle on the docking unit. While the remote is charging it will blink in the display “charging”. The typical time for the remote to fully charge is 3 hours. The remote will indicate when it is fully charged by displaying “charge complete”. It will display “charge complete” for ten minutes then it will go blank. Figure 3 – Remote Docking Carriage The charge should last for several days, dependent on how often the remote is used. When the remote is not in use, return it to the docking station so that it can charge. There is a battery level indicator in the upper right hand corner of the display. This will indicate how much battery life is left in the remote. Figure 4 – Remote Display Dock the iPod onto the 30 pin connection on the dock of the iJet-Nav-Pro. If the remote and the iPod are both docked then the iPod keyboard will be active and functional. When the iPod is docked and the remote is removed from the dock then the iPod will display “OK to disconnect” (note: The remote must be charged) and the iPod keyboard will be locked out. If the remote is placed back into the dock for charge the iPod controls will become enabled and it will exit the “OK to disconnect” mode. Be sure to connect the audio cable from the audio output on www.buyijet.com 3 iJet-Nav-Pro Date: 09-15-10 the docking unit of the iJet-Nav-Pro to the stereo auxiliary input audio left and right channels. Make sure the stereo is set to the correct auxiliary input setting. Set the volume control on the stereo to a mid-range. This way the remote will control higher and lower levels from the mid-range setting. Remote Control Wheel Pad The remote control has on it a wheel shaped key pad for maneuvering the menus and entering song selections, settings, etc. See figure 5 below. Figure 5 - Remote Button Wheel 1.) Menu: To enter a selection or navigate in and out of sub-menus. 2.) Next Song: For next song selection, Fast forward, or enter Sub-Menus. 3.) Previous Song: To play current song again, back up to a previously played song, Fast rewind, or to exit sub-menu. 4.) Volume Up: To increase volume while in the play/pause menu or song selected menu or to move up and down through main menu or sub-menus. Once a song is selected and playing then the volume up and down functions as such. 5.) Volume Down: To decrease volume while in the play/pause menu or song selected menu or to move up and down through main menu or sub-menus. Once a song is selected and playing then the volume up and down functions as such. iPods Compatible with the iJet-Nav-Pro The remote control unit will not start to communicate with the iJet-Nav-Pro dock until the iPod product is place in the docking station. The iPod’s which will work with this product are listed below. • • • • • • • • • • • iPhone 4, 3G, 3GS (See below using the iPhone) iPad iTunes iPod Classic iPod Mini iPod Photo iPod Video iPod 3G iPod 4G iPod 5G iPod 6G iPod Nano (including 5th Gen) www.buyijet.com 4 iJet-Nav-Pro • Date: 09-15-10 iPod Touch (including 3rd Gen) The iPhone Make sure that the iPhone is in the iPod mode before docking the iPhone on the iJet-Nav-Pro docking station. The iJet-Nav-Pro is a music control device therefore the Apple product must be in the correct mode before docking. Waiting for iPod Message The “waiting for the iPod” and/or “Out of Range” message may appear for short duration while the remote waits for the communication link with the dock. If either of these message don’t go away after a short period of time, verify that the iPod is docked on the iJet-Nav-Pro and that the iPod is in the “OK to Disconnect” mode. If you are to far from the dock with the remote control unit, then the “Out of Range” message will appear indicating that you must move closer as communications has been lost. The Remote control communicates with the dock for song, artist and other settings via Radio Frequency communication. Each time new information is to be displayed then the remote will request only the information needed. The artists and playlists information is sent in real time to the iPod remote control. Down loading of song lists and artist list into the remote is no longer necessary as in other products. It will update continuously because it is in constant communication with the iPod. No need to wait for the iPod to send large amounts of data to the remote, the remote will only request the most relevant data it needs to display on the remote. Display Main Menu On the remote display from the main menu there are 6 categorize that can be selected that are listed below. Each will be described in the following sections. Main Menu Play/Pause Playlists Artists Songs Settings Tech Support > > > > > The “Play/Pause” Sub-Menu From the main menu move the highlighted selection bar over the Play/Pause and press the Menu Pad on the selection wheel to enter the Play/Pause Sub-Menu. What shows next to the Play/Pause while viewing in the main menu is one of three song states: See Figure 4. 1.) If song is playing the play symbol will be showing. This is a solid right pointing arrow. www.buyijet.com 5 iJet-Nav-Pro Date: 09-15-10 2.) If the song is paused then the pause symbol will be showing. This is the two vertical lines (II). 3.) If there is no song selected then no symbol will be showing. While in the Play/Pause sub-menu the Up/Down Volume and Next/Prev song controls are active. In order to navigate between play a song and pause, you need to press the “menu” button. The first press will begin to play the song, the second press will take you back to the main menu, the third press will pause the song and the fourth press will take you back to the main menu. This is a process that toggles back and forth between playing, exiting to the main menu and pausing and exiting to main menu. When there is a “>” then you are able to use the “next song” to navigate into the sub-menu. Main Menu Play/Pause Playlist Artists Songs Settings Tech Support II > > > > > Sub-Menu ……... Song Title displayed here Artiest Name displayed here The “Playlists” Sub-Menu Move the Highlighted bar in the main menu display up and down using the Volume up and Volume down pad. Highlight the Playlists selection, and then press the Menu pad. The remote will enter the Playlist sub-mean. Move up or down to select a playlist using the Volume up and Volume down pad. Place the highlighted bar over the desired playlist, press the Menu pad to select. The remote will now enter the songs associated with the selected play list. Again use the Volume up and Volume down pads to maneuver through the songs list. Place the highlighted bar over the song to play then press the”MENU” pad. The song will begin to play. Now use the Volume up and Volume down pads to control the volume while in this sub-menu. Use the next song or previous song to move through the songs list. If a pad is not press for the timeout period the remote will sleep in the low power mode until a button is pressed. This will conserve battery power. To exit the songs sub-menu and go to the main menu use the “MENU” pad. Holding down the volume up or down will allow you to jump through the play list or songs list selections. Hold down the Next Song (PREV) pad to fast forward or Previous Song (NEXT ) pad to rewind. If at the top of the play list then the PREV pad stops working as there is not previous song. Likewise if at the end of a play list the NEXT pad stops working as there is no next song in the list. You can back out of the sub-menu by pressing the PREV song pad. See menu flow chart below. Main Menu Play/Pause Playlist Artists Songs Settings Tech Support > > > > > www.buyijet.com Sub-Menu …..> Playlist 1 Playlist 2 Playlist 3.4.5..n Last Playlist entry Sub-Menu ……> Playlist ……> Play Songs 6 iJet-Nav-Pro Date: 09-15-10 The “Artists” Sub-Menu Move the Highlighted bar in the main menu display up and down using the Volume up and Volume down pad. Place the highlighted bar over the Artists selection and then press the Menu pad. The remote will now enter the Artists sub-mean. Scroll up or down to select an Artiest using the Volume up or Volume down pad. Now place the highlighted bar over the Artist to select then press the Menu pad. The remote will now enter the songs associated with the selected Artist. Again use the Volume up and Volume down pads to maneuver through the songs. Place the highlighted bar over the song to play then press the ”MENU” pad. The song will begin to play. Now use the Volume up and Volume down pads to control the volume while in this sub-menu. Use the next song or previous song to move through the songs list. If a pad is not press for the timeout period the remote will sleep in the low power mode until a button is pressed. This will conserve battery power. To exit the songs sub-menu and go to the main menu use the “MENU” pad. Holding down the volume up or down will allow you to jump through the play list or songs list selections. Hold down the Next song pad to fast forward or Previous Song pad to rewind. If at the top of the play list then the PREV pad stops working as there is not previous song. Likewise if at the end of a play list the NEXT pad stops working as there is no next song in the list. You can back out of the sub-menu by pressing the PREV song pad. See menu flow chart below. Main Menu Play/Pause Playlist Artists Songs Settings Tech Support > > > > > Sub-Menu …..... Artist list 1 Sub-Menu Artist list 2 …….. Artist Songs list ……> Play Songs Artist list 3.4.5..n Last Artist list entry The “Songs” Sub-Menu Move the Highlighted bar in the main menu display up and down using the Volume up and Volume down pad. Place the highlighted bar over the Songs selection. Then press the Menu pad, the remote will enter the Songs sub-mean. You will now see the list of all songs in alphabetical order. Move up or down to select a song using the Volume up and Volume down pad. Place the highlighted bar over the song to select then press the Menu pad. The remote will now play the song. Now use the Volume up and Volume down pads to control the volume while in this sub-menu. Use the next song or previous song to move through the songs list. If a pad is not press for the timeout period the remote will sleep in the low power mode until a button is pressed. This will conserve battery power. To exit the songs sub-menu and go to the main menu use the “MENU” pad. Holding down the volume up or down will allow you to jump through the all songs list. While playing a song hold down the Next song pad to fast forward or Previous song pad to rewind. If at the top of the all songs list then the PREV pad stops working as there is not previous song. Likewise if at the end of the all songs list the NEXT pad stops working as there is no next song in the list. You can back out of the sub-menu by pressing the PREV song pad. If playing a song then enter the MENU pad to exit. See menu flow chart below. www.buyijet.com 7 iJet-Nav-Pro Main Menu Play/Pause Playlist Artists Songs Settings Tech Support > > > > > Date: 09-15-10 Sub-Menu …...... All Songs / Song 1 Sub-Menu All Songs / Song 2 …….. Artist Songs list All Songs / Song 3.4.5..n Last Artist list entry The “Settings” Sub-Menus – Shuffle This allows you to remotely set the shuffle mode on the iPod active for either Songs or Artist. The factory default is off. Main Menu Play/Pause Playlist Artists Songs Settings Tech Support > > > > > Sub-Menu Settings …...... Shuffle ……… Display timer > EQ > Now Playing Mode > Enter iPod Mode About > Sub-Menu Shuffle off Songs Artists The “Settings” Sub-Menus – Display Timer The time which the remote will stay awake between pad presses is determined by this setting. The factory default is 30 Seconds. If you wish the remote to stay active longer between key presses then change the setting to 1 or 2 minutes. Keep in mind the longer the display stays active the sooner the remote will need a recharge. Main Menu Play/Pause Playlist Artists Songs Settings Tech Support > > > > > www.buyijet.com Sub-Menu Settings Shuffle > …...... Display timer >……… EQ > Now Playing Mode > Enter iPod Mode About > Sub-Menu Display Timer 30 Seconds 1 minute 2 minutes 8 iJet-Nav-Pro Date: 09-15-10 The “Settings” Sub-Menus - EQ The Equalizer configuration on the iPod can be remotely changed. Select from the Equalizer settings by placing the highlighted bar over the EQ type and then enter MENU. Main Menu Play/Pause Playlist Artists Songs Settings Tech Support > > > > > Sub-Menu Settings Shuffle > Display timer > Sub-Menu EQ …...... EQ > ……… Lounge Now Playing Mode > Piano Enter iPod Mode Pop About > R&B Rock Small Speaker Spoken Word Treble Booster Vocal Booster The “Settings” Sub-Menus - Now Playing Mode The display show either current song next song or current song and artist when a song is on the display. Select which mode is preferred by placing the highlighted bar over one of the two selections. The factory default is Current song / Next song. Main Menu Play/Pause Playlist Artists Songs Settings Tech Support > > > > > Sub-Menu Settings Shuffle > Display timer > EQ > Sub-Menu Now Playing Mode …...... Now Playing Mode > ………Song/Artist Enter iPod Mode Song/Next Song About > The “Settings” Sub-Menus- Select iPod Mode The setting sub-menu allows you to control the mode of the iPod while the docked. If the iPod is in the “OK to Disconnect” mode the keys on the iPod while on the docking station are disabled. If you wise to enable the keys and exit this mode then enter the settings sub-menu using the volume up/down. Place the highlighted bar over the settings and press the MENU pad. Now again using the volume up/down place the highlighted bar over the selection “Enter iPod Mode” and press MENU pad at the same time. The iPod on the docking station will now exit the “OK to Disconnect” mode. The keys on the iPod are enabled. Remember to re-enable the “OK to Disconnect” mode by pressing the MENU pad and the NEXT SONG pad at the same time. The iPod will not re-enter the “OK to www.buyijet.com 9 iJet-Nav-Pro Date: 09-15-10 Disconnect” mode. It must be in this mode to control all the features available from the wireless remote control. Main Menu Play/Pause Playlist Artists Songs Settings Tech Support > > > > > Sub-Menu Settings Shuffle > Display timer > EQ > Now Playing Mode > Sub-Menu iPod Mode …...... Enter iPod Mode …….. Menu + Track About > restores NAV mode The “Settings” Sub-Menus - About By now you have maneuvered through several menus and have got the wheel control process down. Enter the about sub-menu in the same way you entered any other sub-menu. The About submenu will list the current software version, the unit identification number of the remote and the current signal strength measurement between the dock and the remote. As you walk closer and feather from the dock you will see the sign strength bar increase as the sign gets stronger and decrease in size as the signal gets wicker. If you find that the remote is not communicating with the dock you can allow make sure the sign strength bar has a reading. If there is not indication of sign then simply move closer to dock until there is a reading. Sub-Menu Settings Main Menu Shuffle > Play/Pause Display timer > Playlist > EQ > Artists > Now Playing Mode > Songs > Enter iPod Mode Sub-Menu About Settings > …….. About > …….. Nav-Pro ”Verision Number here” Tech Support > ID = “ID Number here” Sign strength bar While viewing the About menu if you press the Volume up button on the wheel of the remote the ID will increment up. Each time this is done the Dock will attempt to change the to this ID and the conformation message will be displayed. This is only allowed during the first minute of docking of the iPod device. The only need for changing this ID is when two or more iJet-Nav-Pro units are within range of one another. www.buyijet.com 10 iJet-Nav-Pro Date: 09-15-10 The “Tech Support” Sub-Menus This menu keeps at your finger tips the information to contact BuyiJet.com if for any reason you need to do so. Posted on our web site is the contact information as well. Main Menu Play/Pause Playlist > Artists > Songs > Settings > Sub-Menu Tech support Tech Support > …....... BuyiJet.com [email protected] www.buyijet.com The Sleep Mode When the remote is idle for the timeout before sleep period, it will enter the sleep power saver mode. By pressing any pad on the wheel the remote will wake up. That first pad press is a wake up then you must enter the function you want to perform on the wheel pad. Again the first press is just the wake up command. The Hidden Reset button If any sudden abnormal behavior shows up on the remote control then there is a small access hole at the button left side where a paper clip can be inserted to reset the device. See picture below. The switch inside the hole is small and therefore will not need much force to engage. Please only use the reset if necessary. We hope you have many hours of entertainment using our wireless product and again we thank you for your purchase. www.buyijet.com 11