Transcript
1
2
A
7 b
Type 1870 Li+ Model 1870 Li+ Li-Ion
G
F
B
b
a
I
H
a
3
C
4
b
K
J
1 5
a
D E
L
M N 5
C
Operating Instructions Cord/Cordless Hair Clipper
es
> 80%
80 - 65%
65 - 50%
O
50 - 30%
30 - 10%
10 - 0%
en ENGLISH
IMPORTANT SAFEGUARDS
When using your clipper, basic precautions should always be followed: READ ALL INSTRUCTIONS BEFORE USING
DANGER:
To reduce the risk of death or injury by electric shock: 1) Do not place or store appliance where it can fall or be pulled into a tub or sink. Do not place in or drop into water or other liquid. 2) Except when charging, always unplug this appliance from the electrical outlet when not in use. 3) Unplug the clipper or recharge stand from the cord before cleaning. 4) Do not reach for an appliance that has fallen into water. Unplug immediately. 5) Do not use while bathing or in a shower.
WARNING:
To reduce the risk of burns, fire, electric shock or injury to persons: 1) Do Not Crush, Disassemble, Heat above 100˚C (212˚F), or Incinerate the appliance, due to Risk of Fire, Explosion, or Burns. 2) Close supervision is necessary when this appliance is used by, on, or near children or disabled persons. 3) Use this appliance only for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer. 4) Do not use this appliance with damaged or broken blades or broken attachments, as facial injury may occur. 5) Never operate this appliance if it has a damaged cord or battery charger transformer, if it is not working properly, if it has been dropped or damaged, dropped into water. Do not modify or attempt to repair the clipper, charger, plug-in transformer or battery pack. Return the appliance to a Service Center for examination and repair. 6) Do not carry this appliance by supply cord or use cord as a handle. 7) Keep the cord away from heated surfaces. 8) Never drop or insert any object into any opening. 9) Do not place or leave the appliance where it is expected to be subject to damage by an animal or exposed to weather. 10) Do not operate where aerosol (spray) products are being used or where oxygen is being administered. Do not use clipper germicide cleaners containing phynyl phenol. 11) Use only the charger and/or battery pack supplied by the manufacturer. 12) Always attach plug to appliance first, then to outlet. To disconnect, turn all controls to "off" then remove plug from outlet.
SAVE THESE INSTRUCTIONS
THIS CLIPPER WAS DESIGNED FOR COMMERCIAL USE ONLY GENERAL:
1) Only use hair clippers to cut human hair. Only use animal clippers to cut animal hair and animal fur. 2) The appliance is safety insulated and radio screened. It meets the requirements of EU Directive 2004/108/EC regarding electromagnetic compatibility and EC Low Voltage Directive 2006/95/EC. USA Lithium-Ion Battery Replacement, Clipper Repair and Recycling: · For battery replacement send to: Wahl Annex 3001 North Locust, P.O. Box 578, Sterling, IL 61081
· Lithium-Ion batteries can explode, catch fire, and/or cause burns if disassembled, damaged, or exposed to water or high temperatures. · Lithium-Ion batteries are subject to local disposal regulations. Many locations prohibit disposal in standard waste receptacles. Check your local laws and regulations. · For recycling contact a government recycling agency, waste disposal service, retailer, or visit online recycling sources, such as www.batteryrecycling.com or www.rbrc.org. Canada Lithium-Ion Batttery Disposal · Lithium-Ion batteries can explode, catch fire, and/or cause burns if disassembled, damaged, or exposed to water or high temperatures. · Lithium-Ion batteries may be subject to local disposal regulations. Many locations prohibit disposal in standard waste receptacles. Check your local laws and regulations. For recycling contact a government recycling agency, waste disposal service, retailer, or visit online recycling sources, such as www.batteryrecycling.com or www.rbrc.org Description of parts A Blade set B On/off switch C Battery power indicator D Appliance socket E Charging stand F Attachment comb, cutting length 3 mm G Attachment comb, cutting length 6 mm H Attachment comb, cutting length 9 mm I Attachment comb, cutting length 12 mm J Attachment comb, cutting length 18 mm K Attachment comb, cutting length 25 mm L Oil for blade set M Cleaning brush N Plug-in transformer O Appliance plug Mains operation · Connect the appliance plug on the plug-in transformer to the appliance socket (Fig. 1ⓐ). · Connect the plug-in transformer to the mains power supply (Fig. 1ⓑ). · Switch on the appliance using the on/off switch (Fig. 2ⓐ) and, after use, switch it off again (Fig. 2ⓑ). · Note: If the appliance does not function in power supply operation when the battery is fully discharged, switch it off and charge the battery for 5 minutes until the lowest segment of the LCD charge indicator starts to flash. Switch the appliance on again and operate from the power supply. Charging the battery · Connect the appliance plug on the plug-in transformer to the charging stand socket (Fig 3ⓐ). The appliance can also be connected directly to the plug-in transformer for charging. (Fig. 1ⓐ/ⓑ). · Connect the plug-in transformer into the socket (Fig 3ⓑ). · Switch off the appliance using the on/off switch (Fig. 2ⓑ). · Place appliance in the charging stand or connect directly to the plug-in transformer. A signal will sound and the charging process begins. · According to the charge status, the corresponding segment of the battery power indicator blinks during the charging process. Once the battery is fully charged, all segments of the battery power indicator will remain lit continuously. After the device has been removed from the charging stand, the display goes out after approx. 30 seconds. (power saving mode) · Recommendation: To assure the precision of the battery power indicator, the battery should not be recharged until all segments of the battery power indicator have gone out during battery operation.
es ESPAÑOL · Once all segments of the battery power indicator have gone out, the appliance still has approx. 20% remaining capacity. · It should take approx. 1 hour for the appliance to charge to full capacity. · Once the battery is fully charged, a signal will sound. Battery operation · Switch on the appliance using the on/off switch (Fig. 2ⓐ) and, after use, switch it off again (Fig. 2ⓑ). · After the appliance has been switched off, the display goes out about 30 seconds later. (power saving mode) · When the battery is fully charged, the appliance can be used for up to 100 minutes without mains connection. This capacity is attained after approx. 5 - 10 charging cycles. · When the speed of the battery audibly begins to slow down, the battery has a remaining capacity of approx. 2 – 3 minutes. Charging the battery. · When the battery has fully run down, the machine will switch itself off automatically. · Note: In case of insufficient maintenance of the blade set, the operating time can be reduced considerably. Cutting-length adjustment The cutting length can be adjusted to between 0.7 mm and 3 mm (5 possible positions) using the cutting-length adjustment integrated into the blade set (Fig. 4). To do this, set the adjustment lever to the desired position and let it snap into place. Cutting with attachment combs The appliance can also be operated with attachment combs. In order to achieve the indicated cutting length, the cutting length adjustment lever should be set to position 1 (Fig. 4). The following attachment combs are included as standard: 3 mm, 6 mm, 9 mm, 12 mm, 18 mm and 25 mm cutting lengths. Attaching/removing the attachment comb · Slide the attachment comb on to the blade set in the direction of the arrow until it reaches the limit stop (Fig. 5ⓐ). · The attachment comb can be removed by pushing it in the direction of the arrow (Fig. 5ⓑ). Cleaning and Care · Do not immerse the appliance in water! · After each use, remove the attachment comb and use the cleaning brush to remove cut hairs from the housing opening and from the blade set. To do this, remove the blade set (Fig. 6ⓐ) and press the cleaning lever (Fig. 7). This allows the cut hairs that accumulate between the bottom blade and the top blade to be easily removed using the cleaning brush (EASY CLEANING). · The charging contacts on the appliance and charging stand should always be kept clean. · Only wipe the appliance with a soft cloth, which may be dampened slightly. Do not use solvents or abrasives! · The blade set can be cleaned with hygienic spray, order no. 4005-7051. Do not use any other cleaning agents. · The 4in1 Blade Ice spray (order no. 89400) delivers instant cooling, oiling and cleaning of the blade set, while also providing corrosion inhibiting action. · For a long-lasting, good cutting performance, it is important to oil the blade set frequently (Fig. 8). Use only blade set oil for this purpose, order no. 3311 (118.3 ml). · Blade set oil and hygienic spray is available from your dealer or our Service Centre. · If the cutting performance deteriorates after long use despite regular cleaning and oiling, the blade set should be replaced. Automatic Sensor System To ensure that your new hair cutting appliance enjoys a long service life, the appliance needs to be cleaned and oiled on a regular basis (see section Cleaning and Care in the user instructions). To give you advance notice of an urgent need for maintenance care, your hair cutting appliance has been equipped with an automatic sensor system. This system automatically recognises when the blade set needs oiling or cleaning. Consistent heavy soiling or lack of oil can lead to early wear and tear of the appliance.
Should the sensor system recognize such a situation, an acoustic signal sounds and the LCD display blinks for 2 minutes after the hair clipper has been switched off. This signal and blinking can be cancelled by briefly switching the hair clipper on and then off again. Before the hair clipper is again used, you are urgently advised to clean both the hair clipper and the blade set and oil the blade set. Please do so as follows (if these instructions are not observed, the hair clipper can suffer damage and stop working. In such cases the warranty claim expires):
· Switch off the appliance using the on/off switch (Fig. 2ⓑ). · Remove the attachment comb and the blade set and use the cleaning brush to clean the opening of the housing and the blade set. (Fig. 7). · Oil the blade set (Fig. 8). Changing the blade set · Switch off the appliance using the on/off switch (Fig. 2ⓑ). · The blade set can be removed by sliding it away from the housing in the direction of the arrow (Fig. 6ⓐ). · Replace the blade set by hooking it into the housing and pressing it down until it clicks into position in the housing (Fig. 6ⓑ).
b a
a 1870-2290 · 03/2012
en
6
b
8
